U20JL2C48A TOSHIBA HIGH EFFICIENCY DIODE STACK (HED) SILICON EPITAXIAL TYPE U20JL2C48A SWITCHING MODE POWER SUPPLY APPLICATION CONVERTER & CHOPPER APPLICATION z z z z Unit: mm Repetitive Peak Reverse Voltage : VRRM = 600V Average Output Rectified Current : IO = 20A Ultra Fast Reverse−Recovery Time : trr = 35ns (Max) Low Switching Losses and Output Noise. ABSOLUTE MAXIMUM RATINGS (Ta = 25°C) CHARACTERISTIC SYMBOL RATING Repetitive Peak Reverse Voltage VRRM 600 V Average Output Rectified Current IO 20 A Peak One Cycle Surge Forward Current (Sin Wave) Junction Temperature Storage Temperature Range IFSM UNIT 80 (50Hz) A 88 (60Hz) Tj −40~150 °C Tstg −40~150 °C Note: Using continuously under heavy loads (e.g. the application of high JEDEC ― temperature/current/voltage and the significant change in JEITA ― temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. TOSHIBA 12−10D2A operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). ELECTRICAL CHARACTERISTICS (Ta = 25°C) CHARACTERISTIC SYMBOL TEST CONDITION MIN MAX UNIT Peak Forward Voltage VFM IFM = 10A ― 3.2 V Repetitive Peak Reverse Current IRRM VRRM = 600V ― 50 μA trr IF = 2A, di / dt = −50A / μs ― 35 ns tfr IF = 1A ― 100 ns Total DC, Junction to Case ― 1.6 °C / W Reverse Recovery Time Forward Recovery Time Thermal Resistance Rth (j−c) Note 1: VFM, IRRM, trr, tfr ····· A value applied to one cell. POLARITY MARKING 20JL2C Characteristic distinguishing mark Part No. (or brevity code) Lot No. With underline: Lead (Pb)-Free or Lead (Pb)-Free Finish Abbreviation Code Part No. 20JL2C U20JL2C48A 1 2006-11-08 U20JL2C48A Handling Precaution The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be exceeded during operation, even for an instant. The following are the general derating methods that we recommend when you design a circuit with a device. VRRM: We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the absolute maximum rating of VRRM for a DC circuit and be no greater than 50% of that of VRRM for an AC circuit. VRRM has a temperature coefficient of 0.1%/°C. Take this temperature coefficient into account designing a device at low temperature. IO: We recommend that the worst case current be no greater than 80% of the absolute maximum rating of IO. Carry out adequate heat design. If you can’t design a circuit with excellent heat radiation, set the margin by using an allowable Tamax-IO curve. This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180. Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device. We recommend that a device be used at a Tj of below 120°C under the worst load and heat radiation conditions. Please refer to the Rectifiers databook for further information. 2 2006-11-08 U20JL2C48A 3 2006-11-08 U20JL2C48A RESTRICTIONS ON PRODUCT USE 20070701-EN • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 4 2006-11-08