MAXIM MAX5318

EVALUATION KIT AVAILABLE
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
General Description
The MAX5318 is a high-accuracy, 18-bit, serial SPI input,
buffered voltage output digital-to-analog converter (DAC)
in a 4.4mm x 7.8mm, 24-lead TSSOP package. The
device features Q2 LSB INL (max) accuracy and a Q1
LSB DNL (max) accuracy over the full temperature range
of -40NC to +105NC.
The DAC voltage output is buffered resulting in a fast
settling time of 3Fs and a low offset and gain drift of
Q0.5ppm/NC of FSR (typ). The force-sense output (OUT)
maintains accuracy while driving loads with long lead
lengths. Additionally, a separate AVSS supply, allows the
output amplifier to go to 0V (GND) while maintaining full
linearity performance.
The MAX5318 includes user-programmable digital gain
and offset correction to enable easy system calibration.
At power-up, the device resets its outputs to zero or midscale. The wide 2.7V to 5.5V supply voltage range and
integrated low-drift, low-noise reference buffer amplifier
make for ease of use.
The MAX5318 features a 50MHz 3-wire SPI interface. The
MAX5318 is available in a 24-lead TSSOP package and
operates over the -40NC to +105NC temperature range.
Benefits and Features
SIdeal for ATE and High-Precision Instruments

INL Accuracy Guaranteed with ±2 LSB (Max)
Over Temperature
SFast Settling Time (3µs) with 10kI || 100pF Load
SSafe Power-Up-Reset to Zero or Midscale DAC
Output (Pin-Selectable)
Predetermined Output Device State in Power-Up
and Reset in System Design
SNegative Supply (AVSS) Option Allows Full INL
and DNL Performance to 0V
SSPI Interface Compatible with 1.8V to 5.5V Logic
SHigh Integration Reduces Development Time and
PCB Area
Buffered Voltage Output Directly Drives
2kI Load Rail-to-Rail
Integrated Reference Buffer
No External Amplifiers Required
SSmall 4.4mm x 7.8mm, 24-Pin TSSOP Package
Ordering Information and Typical Operating Circuit appear
at end of data sheet.
Applications
Test and Measurement
Equipment
Programmable Voltage
and Current Sources
Automatic Test Equipment
Automatic Tuning and
Calibration
Gain and Offset
Adjustment
Data-Acquisition Systems
Functional Diagram
Communication Systems
VDDIO
REF
AVDD1
AVDD2
24
18
14
21
Medical Imaging
Process Control and
Servo Loops
LDAC
5
CS 9
DIGITAL
OFFSET
SCLK 8
SPI
DIN 7
DOUT 6
SPI
INTERFACE
READY 2
For related parts and recommended products to use with this part,
refer to www.maximintegrated.com/MAX5318.related.
17 REFO
BUFFER
MAX5318
BUSY
4
RST
1
M/Z
3
TC/SB
10
PD
11
7.8kI
DIGITAL
GAIN
INPUT/DAC
REGISTER
DIN
18-BIT
DAC
7.8kI
7.8kI
OUTPUT
BUFFER
CONTROL
LOGIC
POWER-ON
RESET
16 RFB
15 OUT
7.8kI
SHUTDOWN
23
22
13
19
20
12
DGND
BYPASS
AGND
AGND_S
AGND_F
AVSS
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-6465; Rev 0; 9/12
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ABSOLUTE MAXIMUM RATINGS
AGND to DGND....................................................-0.3V to +0.3V
AGND_F, AGND_S to AGND................................-0.3V to +0.3V
AGND_F, AGND_S to DGND................................-0.3V to +0.3V
AVDD to AGND........................................................-0.3V to +6V
AVDD to REF............................................................-0.3V to +6V
AVSS to AGND.........................................................-2V to +0.3V
VDDIO to DGND........................................................-0.3V to +6V
BYPASS to DGND........................................ -0.3V to the lower of
(VAVDD_ or VDDIO + 0.3V) and +4.5V
OUT, REFO, RFB to AGND.......................... -0.3V to the lower of
(VAVDD + 0.3V) and +6V
REF to AGND....................-0.3V to the lower of VAVDD and +6V
SCLK, DIN, CS, BUSY, LDAC, READY,
M/Z, TC/SB, RST, PD, DOUT to DGND........ -0.3V to the lower of
(VDDIO + 0.3V) and +6V
Continuous Power Dissipation (TA = +70NC)
TSSOP (derate 13.9mW/NC above +70NC).............1111.1mW
Operating Temperature Range......................... -40NC to +105NC
Maximum Junction Temperature......................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TSSOP
Junction-to-Case Thermal Resistance (qJA)................13°C/W
Junction-to-Ambient Thermal Resistance (qJA)...........72°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(VAVDD = VDDIO = 4.5V to 5.5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 4.096V, TC/SB =
PD = LDAC = M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = -40°C to +105°C, unless
otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
N
Integral Nonlinearity (Note 3)
INL
Differential Nonlinearity (Note 3)
DNL
Zero Code Error
OE
Zero Code Error Drift (Note 4)
Gain Error
Gain Error Temperature
Coefficient (Note 4)
Output Voltage Range
Maxim Integrated
GE
18
DIN = 0x00000 to 0x3FFFF
(binary mode), DIN = 0x20000 to 0x1FFFF
(two’s complement mode)
DIN = 0x01900 to 0x3FFFF (binary
mode), DIN = 0x21900 to 0x1FFFF (two’s
complement mode), VAVSS = 0V
Bits
-2
Q0.5
+2
LSB
-1
Q0.275
+1
LSB
-48
Q4
+48
DIN = 0, TA = -40NC to +105NC
DIN = 0
-1.6
Q14
Q0.10
+1.6
TA = +25NC
-16
Q1
+16
DIN = 0, TA = +25NC
TA = -40NC to +105NC
TCGE
Q27
-2.5
No load
0
Q0.10
LSB
ppm/NC
LSB
+2.5
ppm/NC
of FSR
VAVDD 0.1
V
2
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDDIO = 4.5V to 5.5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 4.096V, TC/SB =
PD = LDAC = M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = -40°C to +105°C, unless
otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
SYMBOL
CONDITIONS
RST = pulse low
Reset Voltage Output
VOUT-RESET
RST = pulse low,
VAVSS = 0V
RST = DGND
RST = DGND,
VAVSS = 0V
DC Output Impedance (Normal
Mode)
ROUT
Output Resistance (Power-Down
Mode)
Output Current
IOUT
CL
Load Resistance to GND
RL
Short-Circuit Duration
DC Power-Supply Rejection
ISC
TSC
DC PSRR
TYP
MAX
UNITS
75
FV
M/Z = VDDIO
2.048
V
M/Z = DGND
10
mV
M/Z = VDDIO
2.048
V
M/Z = DGND
-68
mV
M/Z = VDDIO
2.036
V
M/Z = DGND
M/Z = VDDIO
Closed-loop connection (RFB connected
to OUT)
PD = VDDIO
Load Capacitance to GND
Short-Circuit Current
MIN
M/Z = DGND
10
mV
2.036
V
4
mI
2
kI
Source/sink within 100mV of the supply
rails
Q4
Source/sink within 800mV of the supply
rails
Q25
mA
200
For specified performance
2
OUT shorted to AGND or AVDD
Q60
REFO shorted to AGND or AVDD
Q65
BYPASS shorted to AGND or AVDD
Q48
Short to AGND or AVDD
pF
kI
mA
s
Indefinite
VOUT at full scale, VAVDD = 4.5V to 5.5V
-2.5
Q0.20
+2.5
VAVSS = -1.5V to -0.5V
-2.5
Q0.012
+2.5
LSB/V
STATIC PERFORMANCE—VOLTAGE REFERENCE INPUT SECTION
VAVDD 0.1
Reference High Input Range
VREF
Reference Input Capacitance
CREF
10
pF
Reference Input Resistance
RREF
10
MI
IB
Q0.15
FA
Reference Input Current
2.4
V
STATIC PERFORMANCE—VOLTAGE REFERENCE OUTPUT SECTION
Reference High Output Range
Reference High Output Load
Regulation
Reference Output Capacitor
Maxim Integrated
VAVDD 0.1
2.4
RESR < 5I
V
500
ppm/
mA
0.1
nF
3
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDDIO = 4.5V to 5.5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 4.096V, TC/SB =
PD = LDAC = M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = -40°C to +105°C, unless
otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
2.3
2.4
2.5
V
1
8
FF
STATIC PERFORMANCE—VBYPASS OUT SECTION
Output Voltage
Load Capacitance to GND
VBYPASS
CL
Required for stability, RESR = 0.1I (typ)
POWER-SUPPLY REQUIREMENTS
Positive Analog Power-Supply
Range
VAVDD
4.5
5.5
V
Digital Interface Power-Supply
Range
VDDIO
1.8
VAVDD
V
Negative Analog Power-Supply
Range
VAVSS
-1.5
-1.25
0
V
Positive Analog Power-Supply
Current
IAVDD
No load, external reference, output at zero
scale
5.2
6.5
mA
Negative Analog Power-Supply
Current
IAVSS
No load, external reference, output at zero
scale
Interface Power-Supply Current
IVDDIO
Digital inputs at VDDIO or DGND
0.2
5.0
FA
Positive Analog Power-Supply
Power-Down Current
PD = VDDIO, power-down mode
20
50
FA
Negative Analog Power-Supply
Power-Down Current
PD = VDDIO, power-down mode
-1.5
-5
-1.0
mA
-3
FA
4.9
V/Fs
3
Fs
1.9
Fs
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
SR
From 10% to 90% full scale, positive and
negative transitions
Voltage Output Settling Time
tS
From falling edge of LDAC to within
0.003% FS, RL = 10kI, DIN = 04000h
(6.25% FS) to 3C000h (93.75% FS)
Busy Time
tBUSY
(Note 5)
DAC Glitch Impulse
Major code transition (1FFFFh to 20000h),
RL = 10kI, CL = 50pF
4
nVs
Digital Feed Through
CSB = VDDIO, fSCLK = 1kHz, all digital
inputs from 0V to VDDIO
1
nVs
Output Voltage-Noise Spectral
Density
At f = 1kHz to 10kHz, without reference,
code = 20000h
26
nV/√Hz
Output Voltage Noise
At f = 0.1Hz to 10Hz, without reference,
code = 20000h
1.55
FVP-P
Wake-Up Time
From power-down mode
75
Fs
Power-Up Time
From power-off
2
ms
Maxim Integrated
4
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ELECTRICAL CHARACTERISTICS
(VAVDD = VDDIO = 2.7V to 3.3V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 2.5V, TC/SB = PD = LDAC =
M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, GAIN = 0x3FFFF, OFFSET = 0x00000,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
N
Integral Nonlinearity (Note 3)
INL
Differential Nonlinearity (Note 3)
DNL
Zero Code Error
OE
Zero Code Error Drift (Note 4)
Gain Error
Gain Error Temperature
Coefficient (Note 4)
GE
18
DIN = 0x00000 to 0x3FFFF (binary
mode), DIN = 0x20000 to 0x1FFFF (two’s
complement mode)
DIN = 0x01900 to 0x3FFFF (binary
mode), DIN = 0x21900 to 0x1FFFF (two’s
complement mode), VAVSS = 0V
DIN = 0, TA = +25NC
Output Current
IOUT
Load Capacitance to GND
CL
Load Resistance to GND
RL
Short-Circuit Current
ISC
Short-Circuit Duration
Maxim Integrated
tSC
-1.0
Q0.3
+1.0
LSB
-50
Q6
+50
Q25
Q1.4
+2.7
-16
Q1.5
+16
TA = -40NC to +105NC
RST = pulse low,
VAVSS = 0V
RST = DGND,
VAVSS = 0V
ROUT
LSB
-2.7
RST = DGND
DC Output Impedance
+2.0
TA = +25NC
Q35
No load
VOUT-RESET
Q0.75
DIN = 0
RST = pulse low
Reset Voltage Output
-2.0
DIN = 0, TA = -40NC to +105NC
TCGE
Output Voltage Range
Bits
LSB
ppm/NC
LSB
-3.2
+3.2
ppm/NC
of FSR
0
VAVDD 0.1
V
M/Z = DGND
75
M/Z = VDDIO
1.25
V
M/Z = DGND
10
mV
M/Z = VDDIO
1.25
V
M/Z = DGND
-40
mV
M/Z = VDDIO
1.25
V
M/Z = DGND
10
mV
M/Z = VDDIO
1.24
V
4
mI
Closed-loop connection, RFB connected
to OUT
Source/sink within 100mV of the supply rails
Q4
Source/sink within 800mV of the supply rails
Q25
FV
mA
200
For specified performance
2
OUT shorted to AGND or AVDD
Q60
REFO shorted to AGND or AVDD
Q65
BYPASS shorted to AGND or AVDD
Q48
Short to AGND or AVDD
pF
kI
Indefinite
mA
s
5
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDDIO = 2.7V to 3.3V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 2.5V, TC/SB = PD = LDAC =
M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, GAIN = 0x3FFFF, OFFSET = 0x00000,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
DC Power-Supply Rejection
SYMBOL
DCPSRR
CONDITIONS
MIN
TYP
MAX
VOUT at full scale, VAVDD = 2.7V to 3.3V
-2.5
Q0.4
+2.5
VAVSS = -1.5V to -0.5V
-2.5
Q0.04
+2.5
UNITS
LSB/V
STATIC PERFORMANCE—VOLTAGE REFERENCE INPUT SECTION
VAVDD 0.1
Reference High Input Range
VREF
Reference Input Capacitance
CREF
10
pF
Reference Input Resistance
RREF
10
MI
IB
Q0.15
FA
Reference Input Current
2.4
V
STATIC PERFORMANCE—VOLTAGE REFERENCE OUTPUT SECTION
Reference High Output Range
VAVDD 0.1
2.4
Reference High Output Load
Regulation
Reference Output Capacitor
RESR < 5I
V
500
ppm/mA
0.1
nF
STATIC PERFORMANCE—VBYPASS OUT SECTION
Output Voltage
Load Capacitance to GND
VBYPASS
CL
2.3
Required for stability, RESR = 0.1I (typ)
2.4
2.5
V
1
8
FF
POWER-SUPPLY REQUIREMENTS
Positive Analog Power-Supply
Range
VAVDD
2.7
3.3
V
Interface Power-Supply Range
VDDIO
1.8
5.5
V
Negative Analog Power-Supply
Range
VAVSS
-1.5
-1.25
0
V
Positive Analog Power-Supply
Current
IAVDD
No load, external reference, output at zero
scale
5.0
6.5
mA
Negative Analog Power-Supply
Current
IAVSS
No load, external reference, output at zero
scale
Interface Power-Supply Current
IVDDIO
Digital inputs at VDDIO or DGND
0.2
5.0
FA
Positive Analog Power-Supply
Power-Down Current
PD = VDDIO, power-down mode
20
50
FA
Negative Analog Power-Supply
Power-Down Current
PD = VDDIO, power-down mode
-1.5
-5
-0.8
mA
-2
FA
4.9
V/Fs
3
Fs
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
SR
From 10% to 90% full scale, positive and
negative transitions
Voltage Output Settling Time
tS
From falling edge of LDAC to within
0.003% FS, RL = 10kI, DIN = 04000h
(6.25% FS) to 3C000h (93.75% FS)
Maxim Integrated
6
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = VDDIO = 2.7V to 3.3V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V, VREF = 2.5V, TC/SB = PD = LDAC =
M/Z = DGND, RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, GAIN = 0x3FFFF, OFFSET = 0x00000,
TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.) (GAIN = 0x3FFFF and OFFSET = 0x00000.)(Note 2)
PARAMETER
Busy Time
SYMBOL
tBUSY
CONDITIONS
MIN
TYP
MAX
UNITS
(Note 5)
1.9
Fs
DAC Glitch Impulse
Major code transition (1FFFFh to 20000h),
RL = 10kI, CL = 50pF
2.5
nVs
Digital Feedthrough
CSB = VDDIO, fSCLK = 1kHz, all digital
inputs from 0V to VDDIO
1
nVs
Output Voltage-Noise Spectral
Density
At f = 1kHz to 10kHz, without reference,
code = 20000h
26
nV/√Hz
Output Voltage Noise
At f = 0.1Hz to 10Hz, without reference,
code = 20000h
1.55
FVP-P
Wake-Up Time
From power-down mode
75
Fs
Power-Up Time
From power-off
2
ms
DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS
(VAVDD = 5V, VDDIO = 2.7V to 5.5V, VAVSS = -1.25V, VREF = 4.096V, RL = 10kω, TC/SB = M/Z = DGND, CREFO = 100pF, CBYPASS
= 1µF, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.)(GAIN = 0x3FFFF and OFFSET = 0x00000.)
(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS (SCLK, DIN, CS, LDAC, M/Z, RST)
Input High Voltage
VIH
Input Low Voltage
VIL
Input Hysteresis (Note 4)
0.7 x
VDDIO
V
0.3 x
VDDIO
VIHYST
200
300
Input Leakage Current
IIN
Q0.1
Input Capacitance
CIN
10
DIGITAL OUTPUT CHARACTERISTICS (DOUT, READY, BUSY)
Output Low Voltage
VOL
ISOURCE = 5.0mA
V
mV
Q1
FA
pF
0.25
VDDIO
- 0.25
V
Output High Voltage
VOH
ISINK = 5.0mA, except for BUSY
Output Three-State Leakage
IOZ
DOUT only
Q0.1
Output Three-State Capacitance
COZ
DOUT only
15
pF
Output Short-Circuit Current
IOSS
VDDIO = 5.25V
Q150
mA
Maxim Integrated
V
Q1
FA
7
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = 5V, VDDIO = 2.7V to 5.5V, VAVSS = -1.25V, VREF = 4.096V, RL = 10kω, TC/SB = M/Z = DGND, CREFO = 100pF, CBYPASS
= 1µF, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.)(GAIN = 0x3FFFF and OFFSET = 0x00000.)
(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
TIMING CHARACTERISTICS
Stand-alone, write mode
Serial Clock Frequency
fSCLK
50
Stand-alone, read mode and daisychained read and write modes (Note 5)
12.5
MHz
Stand-alone, write mode
20
SCLK Period
tCP
Stand-alone, read mode and daisychained read and write modes
80
SCLK Pulse Width High
tCH
40% duty cycle
8
ns
SCLK Pulse Width Low
tCL
40% duty cycle
8
ns
Stand-alone, write mode
8
Stand-alone, read mode
and daisy-chained read
and write modes
38
ns
CS Fall to SCLK Fall Setup Time
tCSSO
First SCLK
falling edge
CS Fall to SCLK Fall Hold Time
tCSH0
Inactive falling edge preceding first falling
edge
0
ns
SCLK Fall to CS Rise Hold Time
tCSH1
24th falling edge
2
ns
ns
DIN to SCLK Fall Setup Time
tDS
5
ns
DIN to SCLK Fall Hold Time
tDH
4.5
ns
SCLK Rise to DOUT Settle Time
tDOT
CL = 20pF (Note 6)
SCLK Rise to DOUT Hold Time
tDOH
CL = 0pF (Note 6)
2
32
ns
SCLK Fall to DOUT Disable Time
tDOZ
24th active edge deassertion
2
30
ns
CS Fall to DOUT Enable
tDOE
Asynchronous assertion
2
30
ns
ns
Stand-alone, aborted sequence
35
Daisy-chained, aborted sequence
70
tCRF
24th falling-edge assertion, CL = 20pF
30
tCRH
24th falling-edge assertion, CL = 0pF
SCLK Fall to BUSY Fall
tCBF
BUSY assertion
CS Rise to READY Rise
tCSR
CL = 20pF
CS Rise to SCLK Fall
tCSA
24th falling edge, aborted sequence
20
ns
CS Pulse Width High
tCSPW
Stand alone
20
ns
SCLK Fall to CS Fall
tCSF
24th falling edge
100
ns
20
ns
20
ns
20
ns
CS Rise to DOUT Disable
tCSDOZ
SCLK Fall to READY Fall
SCLK Fall to READY Hold
LDAC Pulse Width
LDAC Fall to SCLK Fall Hold
RST Pulse Width
Maxim Integrated
tLDPW
tLDH
tRSTPW
Last active falling edge
2
ns
ns
ns
5
ns
35
ns
8
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS
(VAVDD = 5V, VDDIO = 1.8V to 2.7V, VAVSS = -1.25V, VREF = 4.096V, RL = 10kω, TC/SB = M/Z = DGND, CREFO = 100pF, CBYPASS
= 1µF, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.)(GAIN = 0x3FFFF and OFFSET = 0x00000.)
(Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS (SCLK, DIN, CS, LDAC, M/Z, RST)
Input High Voltage
VIH
Input Low Voltage
VIL
Input Hysteresis (Note 4)
0.8 x
VDDIO
0.2 x
VDDIO
VIHYST
Input Leakage Current
IIN
Input Capacitance
CIN
V
200
Input = 0V at VDDIO
300
Q0.1
V
mV
Q1
10
FA
pF
DIGITAL OUTPUTS CHARACTERISTICS (DOUT, READY, BUSY)
Output Low Voltage
VOL
ISOURCE = 1.0mA
Output High Voltage
VOH
ISINK = 1.0mA, except for BUSY
Output Three-State Leakage
IOZ
DOUT only
Output Three-State Capacitance
COZ
DOUT only
Output Short-Circuit Current
IOSS
VDDIO = 2.7V
0.2
VDDIO
- 0.2
V
V
Q0.1
Q1
FA
15
pF
Q150
mA
TIMING CHARACTERISTICS
Serial Clock Frequency
fSCLK
Stand-alone write mode
50
Stand-alone read mode and daisychained read and write modes (Note 6)
8
MHz
Stand-alone write mode
20
SCLK Period
tCP
Stand-alone read mode and daisychained read and write modes
125
SCLK Pulse-Width High
tCH
40% duty cycle
9
ns
SCLK Pulse-Width Low
tCL
40% duty cycle
9
ns
Stand-alone write mode
12
Stand-alone read mode
and daisy-chained read
and write modes
72
ns
CS Fall to SCLK Fall Setup Time
tCSSO
First SCLK
falling edge
CS Fall to SCLK Fall Hold Time
tCSH0
Inactive falling edge preceding first
falling edge
0
ns
SCLK Fall to CS Rise Hold Time
tCSH1
24th falling edge
ns
4
ns
DIN to SCLK Fall Setup Time
tDS
8
ns
DIN to SCLK Fall Hold Time
tDH
8
ns
SCLK Rise to DOUT Settle Time
tDOT
CL = 20pF (Note 7)
SCLK Rise to DOUT Hold Time
tDOH
CL = 0pF (Note 7)
Maxim Integrated
40
2
ns
ns
9
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS (continued)
(VAVDD = 5V, VDDIO = 1.8V to 2.7V, VAVSS = -1.25V, VREF = 4.096V, RL = 10kω, TC/SB = M/Z = DGND, CREFO = 100pF, CBYPASS
= 1µF, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C.)(GAIN = 0x3FFFF and OFFSET = 0x00000.)
(Note 2)
PARAMETER
SYMBOL
CONDITIONS
SCLK Fall to DOUT Disable Time
tDOZ
24th active edge deassertion
CS Fall to DOUT Enable
tDOE
Asynchronous assertion
tCSDOZ
CS Rise to DOUT Disable
MIN
TYP
MAX
UNITS
2
40
ns
2
50
ns
Stand-alone, aborted sequence
70
Daisy-chained, aborted sequence
130
60
ns
SCLK Fall to READY Fall
tCRF
24th falling edge assertion, CL = 20pF
SCLK Fall to READY Hold
tCRH
24th falling edge assertion, CL = 0pF
SCLK Fall to BUSY Fall
tCBF
BUSY assertion
CS Rise to READY Rise
tCSR
CL = 20pF
CS Rise to SCLK Fall
tCSA
24th falling edge, aborted sequence
20
ns
CS Pulse Width High
tCSPW
Stand alone
20
ns
24th falling edge
100
ns
20
ns
20
ns
20
ns
tCSF
SCLK Fall to CS Fall
tLDH
LDAC Fall to SCLK Fall Hold
ns
5
ns
60
Last active falling edge
tRSTPW
RST Pulse Width
Note
Note
Note
Note
Note
Note
2
tLDPW
LDAC Pulse Width
ns
ns
2: All devices are 100% tested at TA = +25°C and TA = +105°C. Limits at TA = -40°C are guaranteed by design.
3: Linearity is tested from VREF to AGND.
4: Guaranteed by design.
5: The total analog throughput time from DIN to VOUT is the sum of tS and tBUSY (4.9µs, typ).
6: Daisy-chain speed is relaxed to accommodate (tCRF + tCSS0).
7: DOUT speed limits overall SPI speed..
DIN
R3
R2
R1
R0
D17
tDS
tDH
1
SCLK
3
2
4
D15
D14
D1
D0
–
5
6
7
8
21
22
–
X
23
24
25
tCSA
tCH
tCSSO
tCSH0
D16
tCP
tCSH1
tCL
CS
tCSPW
DOUT
tDOT
tDOE
Z
0
R3
R2
R1
R0
D17
D16
D15
tDOH
D2
tDOZ
D1
D0
0
tCSF
Z
tCRH
READY
tCRF
tCSR
Figure 1. Serial Interface Timing Diagram, Stand-Alone Operation
Maxim Integrated
10
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
1.2
1.2
0.4
-0.4
INL (LSB)
0.4
INL (LSB)
0.8
0.4
0
0
-0.4
0
-0.4
-0.8
-0.8
-0.8
-1.2
-1.2
-1.2
-1.6
-1.6
-1.6
-2.0
-2.0
131072
196608
-2.0
0
65536
131072
196608
262144
0
131072
196608
CODE
DIFFERENTIAL NONLINEARITY
vs. DIGITAL INPUT CODE
DIFFERENTIAL NONLINEARITY
vs. DIGITAL INPUT CODE
DIFFERENTIAL NONLINEARITY
vs. DIGITAL INPUT CODE
2.0
VREF = 4.096V
VAVDD = 5V
1.6
2.0
1.2
1.2
0.8
0.4
0.4
0.4
-0.4
DNL (LSB)
0.8
DNL (LSB)
0.8
0
0
-0.4
0
-0.4
-0.8
-0.8
-0.8
-1.2
-1.2
-1.2
-1.6
-1.6
-1.6
-2.0
-2.0
65536
131072
CODE
Maxim Integrated
196608
262144
VREF = 2.5V
VAVDD = 3V
1.6
262144
MAX5318 toc06
CODE
1.2
0
65536
CODE
VREF = 5V
VAVDD = 5.25V
1.6
262144
MAX5318 toc05
2.0
65536
VREF = 2.5V
VAVDD = 3V
1.6
0.8
0
DNL (LSB)
2.0
0.8
MAX5318 toc04
INL (LSB)
1.2
VREF = 4.096V
VAVDD = 5V
1.6
INTEGRAL NONLINEARITY
vs. DIGITAL INPUT CODE
MAX5318 toc03
VREF = 5V
VAVDD = 5.25V
1.6
2.0
MAX5318 toc01
2.0
INTEGRAL NONLINEARITY
vs. DIGITAL INPUT CODE
MAX5318 toc02
INTEGRAL NONLINEARITY
vs. DIGITAL INPUT CODE
-2.0
0
65536
131072
CODE
196608
262144
0
65536
131072
196608
262144
CODE
11
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
-0.4
0
-0.8
-1.6
-3.2
-2.0
-4.0
-40 -25 -10 5
20 35 50 65 80 95 110
INTEGRAL NONLINEARITY
vs. TEMPERATURE
100
+25°C
1.6
+105°C
0.8
80
60
VREF = 4.096V
2.4
INL (LSB)
120
4.0
MAX5318 toc09a
-40°C
140
0
-2.4
20
-3.2
MIN INL
0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
LSB
Maxim Integrated
MAX5318 toc09
70
60
-40°C
+10°C
50
+25°C
40
30
20
10
-4.0
0
20 35 50 65 80 95 110
INL DISTRIBUTION vs. TEMPERATURE
MAX INL
-1.6
-40 -25 -10 5
TEMPERATURE (°C)
-0.8
40
MIN DNL
-1.2
20 35 50 65 80 95 110
DNL DISTRIBUTION vs. TEMPERATURE
3.2
-0.4
-2.0
-40 -25 -10 5
TEMPERATURE (°C)
160
0
-1.6
TEMPERATURE (°C)
180
MAX DNL
0.4
-0.8
MIN INL
-2.4
VREF = 4.096V
1.2
0.8
0.8
-1.6
MIN DNL
-1.2
1.6
DNL (LSB)
INL (LSB)
0
2.0
MAX INL
1.6
0.4
-0.8
VREF = 2.5V
2.4
MAX DNL
0.8
DNL (LSB)
3.2
MAX5318 toc10a
1.2
COUNT (NO. OF UNITS)
4.0
MAX5318 toc08
VREF = 2.5V
DIFFERENTIAL NONLINEARITY
vs. TEMPERATURE
MAX5318 toc10
1.6
MAX5318 toc07
2.0
INTEGRAL NONLINEARITY
vs. TEMPERATURE
COUNT (NO. OF UNITS)
DIFFERENTIAL NONLINEARITY
vs. TEMPERATURE
0
-40 -25 -10 5
20 35 50 65 80 95 110
TEMPERATURE (°C)
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4
LSB
12
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
DIFFERENTIAL NONLINEARITY
vs. SUPPLY VOLTAGE
MAX DNL
0.8
0.8
+105°C
0.4
0.4
30
-0.4
-0.8
20
MIN DNL
-2.0
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
2.7
3.5
3.9
4.3
4.7
5.1
VAVDD (V)
VAVDD (V)
DIFFERENTIAL NONLINEARITY
vs. REFERENCE VOLTAGE
INTEGRAL NONLINEARITY
vs. REFERENCE VOLTAGE
ZERO-SCALE OUTPUT ERROR
vs. SUPPLY VOLTAGE
INL (LSB)
0.4
0
-0.4
-0.8
0.4
0
MIN INL
-0.4
-0.8
MIN DNL
1.2
OUTPUT ERROR (LSB)
MAX INL
0.8
0.8
0.4
0
-0.4
-0.8
-1.2
-1.2
-1.6
-1.6
-1.6
-2.0
-2.0
-1.2
2.8
3.2
3.6
4.0
4.4
REFERENCE VOLTAGE (V)
Maxim Integrated
4.8
5.2
VREF = 2.5V
CODE = 0x00000
1.6
5.5
MAX5318 toc15
1.2
MAX DNL
0.8
VAVDD = 5.25V
1.6
2.0
MAX5318 toc14
1.2
2.0
MAX5318 toc13
VAVDD = 5.25V
2.4
3.1
LSB
2.0
1.6
MIN INL
-1.6
-2.0
0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4
0
-0.4
-1.2
-1.6
0
MAX INL
-0.8
-1.2
10
DNL (LSB)
1.2
+40°C
0
VREF = 2.5V
1.6
INL (LSB)
40
1.2
2.0
MAX5318 toc11
+25°C
50
VREF = 2.5V
1.6
DNL (LSB)
COUNT (NO. OF UNITS)
60
2.0
MAX5318 toc10b
70
INTEGRAL NONLINEARITY
vs. SUPPLY VOLTAGE
MAX5318 toc12
INL DISTRIBUTION vs. TEMPERATURE
-2.0
2.4
2.8
3.2
3.6
4.0
4.4
REFERENCE VOLTAGE (V)
4.8
5.2
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VAVDD (V)
13
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
0
-0.4
-0.8
1
SINKING
0
SOURCING
-1
-2
-1.2
-3
-1.6
-2.0
3.1
3.5
3.9
4.3
4.7
5.1
-4
5.5
3
6
+25°C
20
-50 -40 -30 -20 -10 0 10 20 30 40 50
40
30
ZERO CODE ERROR DRIFT
+10°C
70
-40°C
40
30
20
10
10
+105°C
40
30
20
10
0
0
-50 -40 -30 -20 -10 0 10 20 30 40 50
+40°C
60
50
50
20
0
70
60
COUNT (UNITS)
+105°C
LSB
ZERO CODE ERROR DRIFT
+40°C
Maxim Integrated
30
12 15 18 21 24 27 30
COUNT (UNITS)
70
COUNT (NO. OF UNITS)
9
80
MAX5318 toc17b
80
LSB
40
OUTPUT CURRENT (mA)
ZERO CODE ERROR DISTRIBUTION
vs. TEMPERATURE
50
+25°C
0
0
VAVDD (V)
60
+10°C
50
10
MAX5318 toc17c
2.7
-40°C
60
MAX5318 toc17d
0.4
2
70
COUNT (NO. OF UNITS)
OUTPUT ERROR (LSB)
OUTPUT ERROR (LSB)
0.8
CODE = 0x00000
VAVSS = -1.25V
VREF = 4.096V
3
80
MAX5318 toc17
VREF = 2.5V
CODE = 0x3FFFF
1.2
4
MAX5318 toc16
2.0
1.6
ZERO CODE ERROR DISTRIBUTION
vs. TEMPERATURE
ZERO-SCALE OUTPUT ERROR
vs. OUTPUT CURRENT
MAX5318 toc17a
FULL-SCALE OUTPUT ERROR
vs. SUPPLY VOLTAGE
0
0.2
0.4
0.6
0.8
1.0
DRIFT (ppm/°C)
1.2
1.4
1.6
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
DRIFT (ppm/°C)
14
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
+105°C
SINKING
0
SOURCING
-1
-2
-3
40
30
10
10
6
9
12 15 18 21 24 27 30
0
-2.0 -1.8 -1.6 -1.4 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0
-2.0 -1.8 -1.6 -1.4 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0
DRIFT (ppm/°C)
DRIFT (ppm/°C)
OUTPUT CURRENT (mA)
OUTPUT DRIVE CAPABILITY
OUTPUT DRIVE CAPABILITY
OUTPUT ERROR (LSB)
6
4
2
0
-2
-4
CODE = 0x00000
VAVSS = -1.25V
VREF = 4.096V
SINKING CURRENT
TA = +25°C
8
6
OUTPUT ERROR (LSB)
CODE = 0x01900
VAVSS = 0V
VREF = 4.096V
SINKING CURRENT
TA = +25°C
8
10
MAX5318 toc19
10
4
2
OUTPUT DRIVE CAPABILITY
10
0
-2
-4
6
4
2
0
-2
-4
-6
-6
-8
-8
-8
-10
-10
-10
0
1
2
3
4
5
6
OUTPUT CURRENT (mA)
Maxim Integrated
7
8
CODE = 0x3FFFF
VAVDD = 4.2V
VREF = 4.096V
SOURCING CURRENT
TA = +25°C
8
OUTPUT ERROR (LSB)
3
30
20
MAX5318 toc20
0
-40°C
40
20
0
-4
+10°C
50
COUNT (UNITS)
1
60
MAX5318 toc18b
+40°C
50
COUNT (UNITS)
OUTPUT ERROR (LSB)
60
2
GAIN ERROR TEMPERATURE COEFFICIENT
70
MAX5318 toc18a
CODE = 0x3FFFF
VREF = 4.096V
3
GAIN ERROR TEMPERATURE COEFFICIENT
70
MAX5318 toc18
4
MAX5318 toc21
FULL-SCALE OUTPUT ERROR
vs. OUTPUT CURRENT
-6
0
5
10 15 20 25 30 35 40 45 50
OUTPUT CURRENT (mA)
0
1
2
3
4
5
6
7
8
OUTPUT CURRENT (mA)
15
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
OUTPUT DRIVE CAPABILITY
0
-2
-4
4
2
0
-2
-6
-8
-8
-10
-10
5
CODE = 0x00000
VAVSS = -1.25V
VREF = 2.5V
SINKING CURRENT
TA = +25°C
-4
-6
0
MAX5318 toc23
6
0
10 15 20 25 30 35 40 45 50
5
8
5
2
-1
-7
-10
10 15 20 25 30 35 40 45 50
0
5 10 15 20 25 30 35 40 45 50 55 60
5.9
TA = +105°C
OUTPUT CURRENT (mA)
POWER-DOWN SUPPLY CURRENT
vs. SUPPLY VOLTAGE
40
MAX5318 toc25
6.0
VPD = 5V
35
5.7
TA = +105°C
30
5.6
IAVDD (µA)
IAVDD (mA)
11
-4
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
5.5
5.4
25
20
5.3
5.2
TA = +25°C
5.1
TA = +25°C
15
TA = -40°C
5.0
TA = -40°C
10
4.50
4.75
5.00
VAVDD (V)
Maxim Integrated
14
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
5.8
CODE = 0x3FFFF
VAVDD = 5V
VREF = 2.5V
SOURCING CURRENT
TA = +25°C
17
MAX5318 toc26
2
27
OUTPUT ERROR (LSB)
4
8
OUTPUT ERROR (LSB)
6
OUTPUT ERROR (LSB)
MAX5318 toc22
CODE = 0x3FFFF
VAVDD = 5V
VREF = 4.096V
SOURCING CURRENT
TA = +25°C
8
OUTPUT DRIVE CAPABILITY
10
MAX5318 toc24
OUTPUT DRIVE CAPABILITY
10
5.25
5.50
4.50
4.75
5.00
5.25
5.50
VAVDD (V)
16
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
MAX5318 toc27
100
CODE = 0x20000
VOUT
1µV/div
VOLTAGE NOISE (nV/rt-Hz)
90
80
MAX5318 toc28
OUTPUT NOISE DENSITY
0.1Hz TO 10Hz OUTPUT NOISE
70
60
50
40
30
20
10
0
10
1s/div
100
1k
10k
100k
FREQUENCY (Hz)
DIGITAL CLOCK FEEDTHROUGH
GROUND CURRENT vs. CODE
CURRENT THROUGH
AGND_F AND AGND_S
VREF = 4.096V
CURRENT (µA)
500
MAX5318 toc30
MAX5318 toc29
600
VSCLK
5V/div
400
300
VOUT
1mV/div
200
100
0
0
65536
131072
196608
262144
2µs /div
CODE
Maxim Integrated
17
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
MAJOR CARRY GLITCH
(1 LSB NEGATIVE STEP)
MAJOR CARRY GLITCH
(1 LSB POSITIVE STEP)
MAX5318 toc31
MAX5318 toc32
VLDAC
5V/div
VLDAC
5V/div
VOUT
10mV/div
VOUT
10mV/div
400ns/div
400ns /div
SETTLING TIME
(CODE = 0x3C000 to 0x04000)
SETTLING TIME
(CODE = 0x04000 to 0x3C000)
MAX5318 toc33
MAX5318 toc34
VLDAC
5V/div
VLDAC
5V/div
VOUT
2V/div
VOUT
2V/div
VOUT
200µV/div
1µs/div
Maxim Integrated
VOUT
200µV/div
1µs/div
18
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Characteristics (continued)
(VAVDD = VDDIO = 5V, VAVSS = -1.25V, VAGND = VDGND = VAGND_F = VAGND_S = 0V; VREF = 4.096V, TC/SB = PD = M/Z = DGND,
RST = VDDIO, CREFO = 100pF, CL = 100pF, RL = 10kω, CBYPASS = 1µF, TA = +25°C, unless otherwise noted.)
ENTERING POWER-DOWN RESPONSE
EXITING POWER-DOWN RESPONSE
MAX5318 toc35
MAX5318 toc36
VPD
1V/div
VPD
1V/div
VOUT
2V/div
VOUT
2V/div
RL = OPEN
10µs/div
10µs/div
SLOW POWER-UP RESPONSE
(RSTSEL = LOW)
SLOW POWER-UP RESPONSE
(RSTSEL = HIGH)
MAX5318 toc37
4ms/div
Maxim Integrated
MAX5318 toc38
VAVDD
5V/div
VAVDD
5V/div
VAVSS
2V/div
VBYPASS
2V/div
VREFO
2V/div
VAVSS
2V/div
VBYPASS
2V/div
VREFO
2V/div
VOUT
2V/div
VOUT
2V/div
4ms/div
19
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Pin Configuration
TOP VIEW
RST
1
READY
+
24
VDDIO
2
23
DGND
M/Z
3
22
BYPASS
BUSY
4
21
AVDD2
LDAC
5
20
AGND_F
DOUT
6
19
AGND_S
DIN
7
18
REF
SCLK
8
17
REFO
CS
9
16
RFB
TC/SB
10
15
OUT
PD
11
14
AVDD1
AVSS
12
13
AGND
MAX5318
TSSOP
Pin Description
PIN
NAME
FUNCTION
1
RST
Active-Low Reset Input. Drive RST low to DGND to put the device into a reset state. A reset state sets all
SPI input registers to their default power-on reset states as defined by the state of inputs M/Z and TC/SB.
Set RST high to VDDIO, the DAC output remains at the state defined by M/Z until LDAC is taken low.
2
READY
SPI Active-Low Ready Output. READY asserts low when the device successfully completes processing
an SPI data frame. READY asserts high at the next rising edge of CS. In daisy-chain applications, the
READY output typically drives the CS input of the next device in the chain or a GPIO of a microcontroller.
3
M/Z
Reset Select Input. M/Z selects the default state of the analog output (OUT) after power-on or a hardware
or software reset. Connect M/Z to VDDIO to set the default output voltage to midscale or to DGND to set
the default output voltage to zero scale.
4
BUSY
Maxim Integrated
Digital Input/Open-Drain Output. Connect a 2kI pullup resistor from BUSY to VDDIO. BUSY goes low
during the internal calculations of the DAC register data. During this time, the user can continue writing
new data to the DIN, OFFSET, and GAIN registers, but no further updates to the DAC register and
DAC output can take place. If LDAC is asserted low while BUSY is low, this event is stored. BUSY is
bidirectional, and can be asserted low externally to delay LDAC action. BUSY also goes low during
power-on reset, when RST is low, or when software reset is activated.
20
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Pin Description (continued)
PIN
NAME
FUNCTION
5
LDAC
Active-Low Load DAC Logic Input. If LDAC is taken low while BUSY is inactive (high), the contents of the
input registers are transferred to the DAC register and the DAC output is updated. If LDAC is taken low
while BUSY is asserted low, the LDAC event is stored and the DAC register update is delayed until BUSY
deasserts. Any event on LDAC during power-on reset or when RST is low is ignored.
6
DOUT
SPI Bus Serial Data Output. See the Serial Interface section for details.
7
DIN
SPI Bus Serial Data Input. See the Serial Interface section for details.
8
SCLK
SPI Bus Serial Clock Input. See the Serial Interface section for details.
9
CS
10
TC/SB
SPI Bus Active-Low Chip-Select Input. See the Serial Interface section for details.
DIN Format Select Input. Connect TC/SB to DGND to set the data input format to straight binary or to
VDDIO to set it to two’s complement.
11
PD
Active-High Power-Down Input. Connect PD to DGND for normal operation. Connect PD to VDDIO to
place the device in power-down. In power-down, OUT (analog voltage output) is connected to AGND
through a 2kω resistor, but the contents of the input registers and the DAC latch do not change. The SPI
interface remains active in power-down.
12
AVSS
Negative Analog Power-Supply Input. Connect to AGND or a negative supply voltage. When connected
to the negative supply voltage, bypass AVSS with a 0.1µF capacitor to AGND.
13
AGND
Analog Ground. Connect to the analog ground plane.
14
AVDD1
Positive Analog Power-Supply Input. Bypass each AVDD_ locally with a 0.1µF and 10µF capacitor to
AGND (analog ground plane). Connect AVDD1 and AVDD2 together.
15
OUT
Buffered Analog Voltage Output. Connect OUT to RFB externally to close the output buffer feedback
loop. The buffered output is capable of directly driving a 10kω load. The state of M/Z sets the poweron reset state of OUT (zero or midscale). In power-down, OUT is connected to AGND through a 2kω
pulldown resistor.
16
RFB
Feedback Resistor Input. RFB is connected through the internal feedback resistor to the inverting input of
the analog output buffer. Externally connect RFB to OUT to close the output buffer feedback loop.
17
REFO
18
REF
19
AGND_S
DAC Analog Ground Sense
20
AGND_F
DAC Analog Ground Force. Connect to the analog ground plane.
21
AVDD2
Positive Analog Power-Supply Input. AVDD2 supplies power to the internal digital linear regulator. Bypass
AVDD2 locally to AGND with 0.1µF and 10µF capacitors. Connect AVDD2 and AVDD1 together.
22
BYPASS
Internal Bypass Connection. Connect BYPASS to DGND with 0.01µF and 1µF capacitors.
23
DGND
Digital Ground
24
VDDIO
Digital Interface Power-Supply Input. Connect to a 1.8V to 5.5V logic-level supply. Bypass VDDIO with a
0.1µF capacitor to DGND. The supply voltage at VDDIO sets the logic-level for the digital interface.
Maxim Integrated
Voltage Reference Buffered Output. Bypass with a 100pF capacitor to AGND.
High-Impedance 10Mω Voltage Reference Input
21
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Detailed Description
up before AVDD at power up. Follow the recommendations described in the Power-Supply Sequencing section.
The MAX5318 is a high-accuracy, 18-bit, serial SPI input,
buffered voltage output digital-to-analog converter (DAC) in
a 4.4mm x 7.8mm, 24-lead TSSOP package. The device features Q2 LSB INL (max) accuracy and a Q1 LSB DNL (max)
accuracy over the full temperature range of -40NC to +105NC.
Visit www.maximintegrated.com/products/references
for a list of available external voltage-reference devices.
The DAC voltage output is buffered resulting in a fast settling
time of 3Fs and a low offset and gain drift of Q0.5ppm/NC of
FSR (typ). The force-sense output (OUT) maintains accuracy
while driving loads with long lead lengths. Additionally, a
separate AVSS supply allows the output amplifier to go to 0V
(GND) while maintaining full linearity performance.
The MAX5318 includes user-programmable digital gain and
offset correction capability to enable easy system calibration.
At power-up, the device resets its outputs to zero or midscale, providing additional safety for applications, which
drive valves or other transducers that need to be off on
power-up. This is selected by the state of the M/Z input on
power-up.
The wide 2.7V to 5.5V supply voltage range and integrated
low-drift, low-noise reference buffer amplifier makes for ease
of use. Since the reference buffer input has a high input
resistance, an external buffer is not required. The device
accepts an external reference between 2.4V and VAVDD 0.1V for maximum flexibility and rail-to-rail operation.
The MAX5318 features a 50MHz, 3-wire SPI, QSPI,
MICROWIRE, and DSP-compatible serial interface. The separate digital interface supply voltage input (VDDIO) is compatible with a wide range of digital logic levels from 1.8V to
5.5V, eliminating the need for separate voltage translators.
DAC Reference Buffer
The external reference input has a high input (REF) impedance of 10MI||10pF and accepts an input voltage from
+2.4V to VAVDD - 0.1V. Connect an external reference
supply between REF and AGND. Bypass the reference
buffer output REFO to AGND with a 100pF capacitor.
Connect the anode of an external Schottky diode to REF
and the cathode to AVDD1 to prevent internal ESD diode
conduction in the event that the reference voltage comes
Maxim Integrated
Output Amplifier (OUT)
The MAX5318 includes an internal buffer for the DAC
output. The internal buffer provides improved load
regulation for the DAC output. The output buffer slews at
5V/Fs and drives up to 2kI in parallel with 200pF. The
buffer has a rail-to-rail output capable of swinging to
within 100mV of AVDD_ and AVSS.
The positive analog supply voltage (AVDD_) determines
the maximum output voltage of the device as AVDD_
powers the output buffer.
The output is diode clamped to ground, preventing negative voltage excursions beyond approximately -0.6V.
Negative Supply Voltage (AVSS)
The negative supply voltage (AVSS) determines the minimum output voltage. If AVSS is connected to ground, the
output voltage can be set to as low as 100mV without
degrading linearity. For operation down to 0V, connect
AVSS to a negative supply voltage between -0.1V and
-1.5V. The MAX1735 is recommended for generating
-1.25V from a -5V supply.
Force/Sense
The MAX5318 uses force/sense techniques to ensure
that the load is regulated to the desired output voltage despite line drops due to long lead lengths. Since
AGND_F and AGND_S have code dependent ground
currents, a ground impedance less than 13mω ensures
that the INL will not degrade by more than 0.1 LSB. Form
a star ground connection (Figure 2a) near the device
with AGND_F, AGND_S, and AGND tied together. Always
refer remote DAC loads to this system ground for best
performance. Figure 2b shows how to configure the
device and an external op amp for proper force/sense
operation. The amplifier provides as much drive as
needed to force the sensed voltage (measured between
RFB and AGND_S) to equal the desired voltage.
22
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
18-Bit Ideal Transfer Function
The MAX5318 features 18-bit gain and 18-bit offset
adjustment as shown in Figure 3.
The incoming DIN code is multiplied and offset compensated by the generic equation shown in Equation 1. The
resulting value is then applied to the DAC.
OUT
RFB
MAX5318
AGND_F
AGND_S
AGND
Equation 1) Generic gain and offset adjustment
DAC =
DIN × GAIN + OFFSET
The GAIN code is always an 18-bit straight binary word.
The OFFSET code is always two’s complement. It is
therefore simply added to the output of the multiplier.
Figure 2a. Star Ground Connection
To guarantee that a gain of exactly 1 is possible, the
actual gain coefficient applied to DIN is as defined in
Equation 2.
OUT
RFB
Equation 2) Calculation of gain
G=
(GAIN) + 1
AGND
MAX5318
AGND_F
218
AGND_S
When DIN is straight binary, the ideal transfer function is
given by:
Equation 3) Straight binary ideal transfer function
Figure 2b. Force/Sense Connection
VOUT =×
G VDIN + VOFFSET
When DIN is two’s complement, the ideal transfer function is given by:
Equation 4) Two’s complement ideal transfer function
LDAC
OFFSET
V
VOUT
= REF + G × VDIN + VOFFSET
2
VDIN and VOFFSET are the voltages to which the DIN and
OFFSET codes are converted and VOUT is the voltage at
the DAC output buffer. See the Conversion Formulas for
DIN, GAIN, and OFFSET section for equations needed
to convert the DIN and OFFSET codes into VDIN and
VOFFSET.
Maxim Integrated
SPI
INTERFACE
GAIN
DIN
DAC
REGISTER
Figure 3. Gain and Offset Adjustment
23
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
The data DIN can be either straight binary or two’s complement. In straight binary, zero code results in a zeroscale output. In two’s complement, zero code results in
a midscale output.
To better understand how GAIN and OFFSET affect the
output voltage, see Figure 4 and Figure 5. Consider
the generation of a ramp. For now assume OFFSET
is set to 0x00000. In straight binary mode, with GAIN
set to 0x3FFFF (G = 1), DIN starts from 0x00000 and
increases to 0x3FFFF. The output voltage will start at 0V
and increase to (VREF - 1 LSB). If GAIN is reduced, the
ramp will still start at 0V but the maximum level reached
is reduced.
With DIN set to two’s complement mode, to generate the
same ramp, DIN would start at 0x20000 and increase
until it wraps around to 0x00000. At this point the
DAC output would be midscale. DIN then increases to
0x1FFFF where the output would be full-scale -1 LSB. As
POSITIVE OFFSET
IDEAL CHARACTERISTIC
NEGATIVE OFFSET
VOUT
In both cases, a nonzero value for OFFSET results in the
output moving up or down.
Should the output of the gain and offset adjust block
overflow full-scale or underflow zero-scale, the data is
clipped so the DAC output will be clipped rather than
overflow or underflow.
The effect of gain and offset adjustment is shown in
Figure 4 for straight binary mode and Figure 5 for two’s
complement mode.
If any of the DIN, GAIN, or OFFSET registers is changed,
the device takes 1.9µs (tBUSY) to compute the new values to present to the DAC. While the device is computing
the new DAC value, the BUSY output is set low. See the
section on the BUSY output and LDAC input for details.
POSITIVE OFFSET
IDEAL CHARACTERISTIC
NEGATIVE OFFSET
FULL-SCALE
VREF
GAIN is reduced, the start of the ramp becomes larger
and the end of the ramp becomes smaller. The ramp is
therefore centered at midscale.
VOUT
FULL-SCALE
VREF
GAIN < 0x3FFFF (G < 1)
MIDSCALE
MIDSCALE
GAIN < 0x3FFFF (G < 1)
ZERO-SCALE
0V
00000h
20000h
3FFFFh
DIN
Figure 4. Gain and Offset Adjustment in Straight Binary Mode
Maxim Integrated
ZERO-SCALE
0V
20000h
00000h
1FFFFh
DIN
Figure 5. Gain and Offset Adjustment in Two’s Complement
Mode
24
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Conversion Formulas for DIN,
GAIN, and OFFSET
Input, Gain, and Offset Ranges
The ranges of DIN, GAIN, and OFFSET are summarized
in Table 4 to Table 6. Also shown are the range values
for the 18-bit MAX5318 with a 4.096V reference. Note that
VREF is the reference voltage applied to REF and 1 LSB
is equal to VREF/218.
Tables 1a and 1b show how to convert the DIN code to
VDIN in straight binary and two’s complement modes.
Table 2 shows how to convert the GAIN code to the gain
factor G, which is multiplied with VDIN. Table 3 shows
how to convert the OFFSET code to VOFFSET, which is
summed with the product G•VDIN.
Table 1a. Converting DIN to VDIN (Straight Binary Mode)
DIN
EQUATION FOR VDIN
V
=
DIN VREF ×
0x00000 to 0x3FFFF
DIN
2 18
RANGE
0V to (VREF - 1 LSB)
Table 1b. Converting DIN to VDIN (Two’s Complement Mode)
DIN
EQUATION FOR VDIN AND VOFFSET
RANGE
0x20000 to 0x3FFFF
 DIN - 0x20000  VREF
V=
DIN VREF × 
2
2 18


VREF/2 to -1 LSB
V=
DIN VREF ×
0x00000 to 0x1FFFF
CODE
2
18
0V to (VREF/2 1 LSB)
Table 2. Converting GAIN to G
GAIN
0x00000 to 0x3FFFF
EQUATION
G=
RANGE
GAIN + 1
1/218 to 1
2 18
Table 3. Converting OFFSET to VOFFSET
OFFSET
EQUATION
RANGE
0x20000 to 0x3FFFF
 OFFSET − 0x20000  VREF
VOFFSET =
VREF × 
−
2
2 18


-VREF/2 to -1 LSB
0x00000 to 0x1FFFF
Maxim Integrated
VOFFSET
= VREF ×
OFFSET
2 18
0V to (VREF/2 - 1 LSB)
25
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 4a. DIN Range (Straight Binary Mode)
RANGE
DIN
VDIN (V)
VALUE (V)
Minimum
0x00000
0
0
Maximum
0x3FFFF
(VREF - 1 LSB)
4.095984375
Table 4b. DIN Range (Two’s Complement Mode)
RANGE
DIN
VDIN (V)
VALUE (V)
Minimum
0x20000
0
0
Maximum
0x1FFFF
(VREF - 1 LSB)
4.095984375
Table 5. GAIN Range
RANGE
GAIN
G
VALUE (V)
Minimum
0x00000
1/218
0.0000038147
Maximum
0x3FFFF
1
1
Table 6. OFFSET Range
RANGE
OFFSET
VOFFSET (V)
VALUE (V)
Minimum
0x20000
-VREF/2
-2.048
Maximum
0x1FFFF
(VREF/2 - 1 LSB)
2.047992188
Table 7. Straight Binary DIN Examples
DIN
0x20000
0x30000
VDIN (V)
2.048
3.072
Maxim Integrated
GAIN
0x2FFFF
0x0FFFF
G
0.75
0.25
OFFSET
0x10000
0x30000
VOFFSET (V)
CALCULATION
COMMENT
1.024
VOUT = 0.75 x
2.048 + 1.024
= 2.56V
•
•
•
•
For VOUT, use Equation 3
For VDIN, use Table 1a
For G, use Table 2
For VOFFSET, use Table 3 second
formula
-1.024
VOUT = 0.25 x
3.072 - 1.024
= 0.512V
•
•
•
•
For VOUT, use Equation 3
For VDIN, use Table 1a
For G, use Table 2
For VOFFSET, use Table 3 first
formula
26
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 8. Two’s Complement DIN Examples
DIN
0x30000
0x10000
VDIN (V)
-1.024
1.024
GAIN
0x2FFFF
0x0FFFF
G
0.75
0.25
OFFSET
0x08000
0x38000
VOFFSET (V)
CALCULATION
0.512
VOUT = 4.096/2
+ 0.75 x (-1.024)
+ 0.512 = 1.792V
•
•
•
•
For VOUT, use Equation 4
For VDIN, use Table 1b first formula
For G, use Table 2
For VOFFSET, use Table 3 second
formula
-0.512
VOUT = 4.096/2
+ 0.25 x 1.024
- 0.512 = 1.792V
•
•
•
•
For VOUT, use Equation 4
For VDIN, use Table 1b first formula
For G, use Table 2
For VOFFSET, use Table 3 first
formula
Numerical Examples
Several numerical examples for the MAX5318, as shown
in Table 7 and Table 8, illustrate how the gain and offset control changes the output voltage. The examples
assume a reference voltage of 4.096V. Note that if the
result of the calculation results in an under- or over-range
output voltage, VOUT is set to its zero or full-scale value,
respectively. An under-range output is less than 0V and
an over-range output is greater than VREF - 1 LSB.
Reset
The device is reset upon power-on, hardware reset using
RST, or software reset using register 0x4, bit 15, command RSTSW. After reset, the value of the input register,
the DAC latch and the output voltage are set to the values
defined by the M/Z input. If a hardware reset occurs during a SPI programming frame, anything before and after
the reset for the frame will be ignored. A software reset
initiated through the SPI interface takes effect after the
end of the valid frame.
Output State Upon Reset
The output voltage can be set to either zero or midscale upon power-up, or a hardware or software reset,
depending on the state of the M/Z input. After power-up,
if the device detects that this input is low, the output voltage is set to zero scale. If M/Z is high, the output voltage
is set to midscale.
Maxim Integrated
COMMENT
Note that during reset, when RST is low or RSTSW is set
to 0, the output voltage is set slightly lower than the value
after coming out of reset. During reset, the output voltage
is set to the values shown for the VOUT-RESET specification in the Electrical Characteristics.
Power-Down
The device can be powered down by either hardware
(pulling PD high) or software (setting the PD_SW bit in
either the 0x4 or 0xC registers). Note that the hardware
and software inputs are ORed. Asserting either is enough
to place the device in power-down mode.
In order to restore normal operation to the device, satisfy
both of these conditions:
1) Pull PD low.
2) Set the bits PD_SW’s (in both 0x4 and 0xC registers)
to 0.
In power-down, the output is internally connected to
AGND through a 2kI resistor. The SPI interface remains
active and the DAC register content remains unchanged.
Data Format Selection
(Straight Binary vs. Two’s Complement)
The MAX5318 interprets the data code input (DIN) as
either straight binary or two’s complement. To choose the
straight binary format, set the TC/SB input low. For two’s
complement, set the input high.
27
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
LDAC and BUSY Interaction
event but does not implement it until processing is
complete. Then, BUSY goes high and the device
updates the DAC.
The BUSY line is open drain and is normally pulled up
by an external resistor. It is software-configurable bidirectional and can be pulled down externally. If any of the
DIN, GAIN, and OFFSET registers is changed, the device
must calculate the value to be presented to the DAC register. To indicate to the host processor that the device is
busy, the device pulls the BUSY output low. Once computation is complete, the device releases BUSY and the
host processor can load the DAC by toggling the LDAC
input. If LDAC is set low while BUSY is low, the LDAC
event is latched and implemented when the computation
is complete and BUSY rises.
3) LDAC is held low. The host sends a new command
and the device sets BUSY low. The device updates
the DAC when the processing is complete and BUSY
goes high.
4) BUSY is pulled down externally to delay DAC update.
The BUSY pin is bidirectional. To use BUSY as an
input, set the NO_BUSY bit to 1 using the 0x4 or 0xC
command. When configured as an input, pulling BUSY
low at least 50ns before the device releases the line
delays DAC update. DAC update occurs only after
BUSY is released and goes high. If used as an input,
drive BUSY with an open-drain output with a pullup
to VDDIO. The processing required for calculating the
final DAC code is controlled by an internally generated
clock. The clock frequency is not related to any external signals and the frequency is not precisely defined.
Therefore, if the DAC must be updated at a precise
time with the least amount of jitter, use option 1.
There are four ways in which the LDAC and BUSY outputs can be used. This is shown graphically in Figure 6.
1) The host sends a new command. The device sets BUSY
low. The host monitors BUSY to determine when it goes
high. The device then pulses LDAC low to update the
DAC.
2)The host sends a new command. The device sets
BUSY low. The host toggles LDAC low then high
before BUSY goes high. The device latches the LDAC
DIN
X
1
2
X
21
22
23
X
INPUT REGISTER LOADED
SCLK
BUSY
tBUSY
LDAC
tS
tCBF
OPTION 1
VOUT
tLDPW
LDAC
tLDH
OPTION 2
VOUT
LDAC
OPTION 3
OPTION 4
VOUT
BUSY
(USED AS INPUT)
BUSY PULLED LOW EXTERNALLY
50ns
LDAC
VOUT
Figure 6. BUSY and LDAC Timing
Maxim Integrated
28
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Serial Interface
upon the type of read command. Table 9 shows the bit
positions for DOUT and DIN within the 24-bit SPI frame.
Overview
The SPI interface supports speeds up to 50MHz. When
CS is high, the remaining interface inputs are disabled to
reduce transient currents. The interface supports daisy
chaining to enable multiple devices to be controlled on
the same SPI bus.
The device is designed such that SCLK idles low, and
DIN and DOUT change on the rising clock edge and get
latched on the falling clock edge. The SPI host controller
should be set accordingly.
Daisy-Chain SPI Operation Using READY Output
The READY pulse appears 24 clock cycles after the negative edge of CS as shown in Figure 7 and can therefore
be used as the CS line for the next device in the daisy
chain. Since the device looks at the first 24 bits of the
transmission following the falling edge of CS, it is possible to daisy-chain the device with different command
word lengths. READY goes high after CS is driven high.
The device has a double-buffered interface consisting
of two register banks: the input register and the DAC
register. The input register for DIN/GAIN/OFFSET is connected directly to the 24-bit SPI input shift register. The
DAC latch contains the DAC code after digital processing and is loaded as defined in the LDAC and BUSY
Interaction section above.
A valid SPI frame is 24-bit wide with 4-bit command R3
to R0, 18-bit data D17 to D0, and 2 unused LSBs. A full
24-bit SPI command sequence is required for all SPI
command operations, regardless of the number of data
bits actually used for the command. Any commands
terminating with less than a full 24-bit sequence will be
aborted without impacting the operation of the part (subject to tCSA timing requirements). Data is not written into
the SPI input register or DAC and it continues to hold the
preceding valid data. If a command sequence with more
than 24 bits is provided, the command will be executed
on the 24th SCLK falling edge and the remainder of the
command will be ignored.
To perform a daisy-chain write operation, drive CS low
and output the data serially to DIN. The propagation of
the READY signal then controls how the data is read by
the device. As the data propagates through the daisy
chain, each individual command in the chain is executed
on the 24th falling clock edge following the falling edge
of the respective CS input. To update just one device
in a daisy chain, send the no-op command to the other
device in the chain. To update the first device in the
chain, raise the CS input after writing to that device.
Because daisy-chain operation requires paralleling the DOUTs of all the MAX5318 in the chain, the
NO_HOLDEN bit in register 0x4 or 0xC should be set
to 1 for all devices. Doing so ensures that DOUT goes
into high-impedance after the SPI frame is complete
(i.e. after the 24th clock cycle) as shown in Figure 8.
All SPI commands result in the device assuming control of the DOUT line from the first SCLK edge through
the 24th SCLK edge. After relinquishing the DOUT line,
the MAX5318 returns to a high-impedance mode. An
optional bus hold circuit can be engaged to hold DOUT
at its last bit value while not interfering with other devices
on the bus.
Stand-Alone Operation
The diagram in Figure 9 shows a stand-alone connection of the MAX5318 in a typical SPI application. If more
than one peripheral device shares the DOUT bus, the
NO_HOLDEN bit in register 0x4 or 0xC should be set to 1
for the MAX5318. Doing so ensures that DOUT goes into
high-impedance after the SPI frame is complete (i.e. after
the 24th clock cycle).
DOUT is disabled at power-up and must be enabled
through the SPI interface. When enabled, DOUT echoes
the 4-bit command plus 18-bit data, which is being
programmed. During readback, DOUT echoes the 4-bit
command followed by the true readback data depending
Table 9. SPI Command and Data Mapping with Clock Falling Edges
CLOCK
EDGE
DIN
DOUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
R3 R2 R1 R0 D17 D16 D15 D14 D13 D12 D11 D10 D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
X
0 R3 R2 R1 R0 D17 D16 D15 D14 D13 D12 D11 D10 D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X
Note that ‘X’ is don’t care.
Maxim Integrated
29
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
µC
MISO
MOSI
SCK
SLAVE 1
SLAVE 2
CS
DOUT
DIN
SCLK
DOUT
DIN
SCLK
DOUT
DIN
SCLK
I/O
SLAVE 3
READY
READY
CS
READY
CS
Figure 7. Daisy-Chain SPI Connection Terminating with a Standard SPI Device.
CS
DIN
SLAVE 1 DATA
SLAVE 2 DATA
SLAVE 3 DATA
SCLK
READY 1
1
2
3
4
20
21
22
23
24
1
2
3
4
5
21
22
23
24
1
2
3
4
5
21
22
23
24
READY 2
READY 3
HI-Z
DOUT1
DOUT2
DOUT3
HI-Z
HI-Z
HI-Z
Figure 8. Daisy-Chain SPI Connection Timing
Maxim Integrated
30
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Command and Register Map
All command and data registers have read and write
functionality. The register selected depends on the command select bits R[3:0]. Each write to the device consists
of 4 command select bits (R[3:0]), 18 data bits (which are
detailed in Table 11 to Table 19), and 2 don’t care LSBs.
A summary of the commands is shown in Table 10.
Applications Information
Power-On Reset (POR)
Upon power-on, the output is set to either zero-scale
(if M/Z is low) and midscale (if M/Z is high). The entire
register map is set to their default values as shown in
Table 11 to Table 19.
TO OTHER DEVICES/CHAINS
µC
CSm
MAX5318
CS1
CS
CS
SCLK
SCLK
DWRITE
DIN
DREAD
DOUT
Figure 9. Stand-Alone Operation
Table 10. Register Map Summary
HEX
R3
R2
R1
R0
0
0
0
0
0
No-op. Used mainly in daisy-chain communications.
FUNCTION
1
0
0
0
1
DIN register write
2
0
0
1
0
OFFSET register write
3
0
0
1
1
GAIN register write
4
0
1
0
0
Configuration register write
5–8
—
—
—
—
Reserved
9
1
0
0
1
DIN register read
A
1
0
1
0
OFFSET register read
B
1
0
1
1
GAIN register read
C
1
1
0
0
Configuration and status register read.
D–F
—
—
—
—
Reserved
Maxim Integrated
31
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Register Details
Table 11. No-Op Command (0x0)
BIT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DEFAULT
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
BIT
NAME
17:0
DESCRIPTION
No action on SPI shift register and DAC input registers. Use for daisy-chain purposes when
R[3:0] = 0000.
Don’t care
Table 12a. Straight Binary DIN Write Register (TC/SB) = 0) (0x1)
BIT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
0x00000 when M/Z = DGND (zero scale)
0x20000 when M/Z = VDDIO (midscale)
BIT
NAME
17:0
DESCRIPTION
18-bit DAC input code in straight binary format. For clarity, a few examples are shown below:
00 0000 0000 0000 0000
0x00000
zero scale
01 0000 0000 0000 0000
0x10000
quarter scale
10 0000 0000 0000 0000
0x20000
midscale
11 0000 0000 0000 0000
0x30000
three-quarter scale
11 1111 1111 1111 1111
0x3FFFF
full scale - 1 LSB
B[17:0]
Table 12b. Two’s Complement DIN Write Register (TC/SB) = 1) (0x1)
BIT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
0x20000 when M/Z = DGND (zero scale)
0x00000 when M/Z = VDDIO (midscale)
BIT
17:0
Maxim Integrated
NAME
DESCRIPTION
B[17:0]
18-bit DAC input code in two’s complement format. For clarity, a few examples are shown below:
10 0000 0000 0000 0000
0x20000
zero scale
11 0000 0000 0000 0000
0x30000
quarter scale
11 1111 1111 1111 1111
0x3FFFF
midscale - 1 LSB
00 0000 0000 0000 0000
0x00000
midscale
00 0000 0000 0000 0001
0x00001
midscale + 1 LSB
01 0000 0000 0000 0000
0x10000
three-quarter scale
01 1111 1111 1111 1111
0x1FFFF
full scale - 1 LSB
32
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 13. OFFSET Register Write in Two’s Complement (0x2)
BIT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
0x00000—Zero Offset
BIT
NAME
17:0
DESCRIPTION
18-bit offset code in two’s complement format. For clarity, a few examples are shown below:
10 0000 0000 0000 0000
0x20000
offset of -217
11 1111 1111 1111 1111
0x3FFFF
offset of -1
00 0000 0000 0000 0000
0x00000
offset of 0
00 0000 0000 0000 0001
0x00001
offset of +1
01 1111 1111 1111 1111
0x1FFFF
offset of 217 – 1
B[17:0]
Table 14. GAIN Write Register (0x3)
BIT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
DEFAULT
0x3FFFF—Gain of 1
BIT
17:0
NAME
B[17:0]
Maxim Integrated
DESCRIPTION
18-bit gain code. For clarity, a few examples are shown below:
11 1111 1111 1111 1111
3FFFF\h
Gain of 1. (218 – 1 + 1)/218
11 1111 1111 1111 1110
3FFFE\h
Gain of 0.999996. (218 – 2 + 1)/218
01 1111 1111 1111 1111
1FFFF\h
Gain of 0.5. (217 – 1 + 1)/218
01 1111 1111 1111 1110
1FFFE\h
Gain of 0.499996. (217 – 2 + 1)/218
00 0000 0000 0000 0000
00000\h
Gain of 0.0000076. 1/218
33
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 15. General Configuration Write Register (0x4)
BIT
NAME
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PD_SW
NO_HOLDEN
X
X
X
X
X
X
X
X
X
X
X
X
X
0
NO_BUSY
0
DOUT_ON
0
RST_SW
1
0
X
X
X
X
X
X
X
X
X
X
X
X
X
DEFAULT
BIT
NAME
17
PD_SW
DESCRIPTION
Software PD (Power-Down). Equivalent to the PD input.
0: Normal mode
1: Power-down mode. OUT is internally connected to AGND using a 2kI resistor.
NO_HOLDEN
SPI Bus Hold Enable.
0: Bus hold enabled for SPI DOUT output. DOUT stays at its last value after the SPI CS
input rises at the end of the SPI frame (i.e. after the 24th clock cycle).
1: Bus hold disabled for SPI DOUT output. DOUT goes high impedance after the SPI CS
input rises at the end of the SPI frame (i.e. after the 24th clock cycle).
RST_SW
Software Reset. Equivalent to the RST input.
0: Place device in reset
1: Normal operation
Set the active low RST_SW bit low to initiate a software reset (equivalent to pulling RST low)
NO_BUSY
BUSY Input Disable.
0: BUSY input is active.
1: BUSY input is disabled.
Note that this does not affect the BUSY bit in the General Configuration and Status
Register. The BUSY pin is bidirectional. When enabled, it can be pulled down externally
to delay DAC updates.
13
DOUT_ON
SPI DOUT Output Disable. DOUT is disabled by default.
0: DOUT output disabled. When DOUT is disabled, the output is pulled low for the
duration of the SPI frame.
1: DOUT output enabled.
12:0
—
16
15
14
Maxim Integrated
Don’t care. These bits are reserved for the corresponding read command.
34
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 16. DIN Read Register (0x9)
BIT
NAME
DEFAULT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT
NAME
17:0
B[17:0]
DESCRIPTION
18-bit DIN readback value.
Table 17. OFFSET Read Register (0xA)
BIT
NAME
DEFAULT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT
NAME
17:0
B[17:0]
DESCRIPTION
18-bit OFFSET readback value in two’s complement.
Table 18. GAIN Read Register (0xB)
BIT
NAME
DEFAULT
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BIT
NAME
17:0
B[17:0]
Maxim Integrated
DESCRIPTION
18-bit GAIN readback value.
35
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Table 19. General Configuration and Status Read Register (0xC)
BIT
NAME
17
16
15
14
13
12
11
10
9
8 7
6
5
2
1
0
PD_SW
NO_
HOLDEN
RST_SW
NO_BUSY
DOUT_ON
BUSY
X
X
X X X
X
REV_ID[3:0]
X
X
0
0
1
0
0
0
0
0
0
0
0001
0
0
DEFAULT
BIT
17
NAME
PD_SW
0 0
4
3
DESCRIPTION
Software PD (Power-Down). Equivalent to the PD input.
0: Normal mode.
1: Power-down mode. OUT is internally connected to AGND using a 2kI resistor.
NO_HOLDEN
SPI Bus Hold Enable.
0: Bus hold enabled for SPI DOUT output. DOUT stays at its final value after the SPI CS input
rises at the end of the SPI frame.
1: Bus hold disabled for SPI DOUT output. DOUT goes high impedance after the SPI CS
input rises at the end of the SPI frame.
RST_SW
Software Reset. Equivalent to the RST input.
0: Place device in reset.
1: Normal operation.
Set the active low RST_SW bit low to initiate a software reset (equivalent to pulling RST low).
NO_BUSY
BUSY Input Disable.
0: BUSY input is active.
1: BUSY input is disabled.
Note that this does not affect the BUSY bit in the General Configuration and Status Register.
The BUSY pin is bidirectional. When enabled, it can be pulled down externally to delay DAC
updates.
13
DOUT_ON
SPI DOUT Output Disable. DOUT is disabled by default.
0: DOUT output disabled. When DOUT is disabled, the output is pulled low for the duration
of the SPI frame.
1: DOUT output enabled.
12
BUSY
11:6
—
5:2
REV_ID[3:0]
1:0
—
16
15
14
Maxim Integrated
Global BUSY status readback.
0: Device is busy calculating output voltage.
1: Device is not busy.
Reserved. Will read back 0.
Device revision
Reserved. Will read back 0.
36
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Power Supplies and
Bypassing Considerations
For best performance, use a separate supply for the
MAX5318. Bypass VDDIO, AVDD_, and AVSS with highquality ceramic capacitors to a low-impedance ground
as close as possible to the device. A typical high-quality
X5R 10FF capacitor can become self resonant at 2MHz.
Therefore, it is actually an inductor above 2MHz and is
useless for decoupling signals above 2MHz. It is therefore recommended that several capacitors of different
values are connected in parallel. Figure 10 shows the
magnitude of impedance of typical 1FF, 100nF, and
10nF X5R capacitors. As the capacitance reduces, the
self-resonant frequency increases. In addition, the parallel combination of all three is shown and exhibits a significant improvement over a single capacitor. These plots
do not include any PCB trace inductance.
Minimize lead lengths to reduce lead inductance. Adding
just 2nH trace inductance to each of the typical capacitors above produces the effects shown in Figure 11. This
shows significant reduction in the self-resonant frequencies of the capacitors.
Internal Linear Regulator (BYPASS)
BYPASS is the output of an internal linear regulator and is
used to power digital circuitry. Connect BYPASS to DGND
with a ceramic capacitor in the range of 1FF to 10FF with
ESR in the range of 100mI to 20mI to ensure stability.
The typical voltage on this pin is 2.4V. Use a low-leakage
capacitor to ensure low power-down current.
Power-Supply Sequencing
During power-up, ensure that AVDD_ comes up before
the reference does. If this is not possible, connect a
Schottky diode between the REF and AVDD_ such as
the MBR0530T1G. If REF does come up before AVDD_,
the diode conducts and clamps REF to AVDD_. Once
AVDD_ has come up, the diode no longer conducts.
REF should always be below AVDD_ as specified in the
Electrical Characteristics. AVDD_ and AVDD_ should be
connected together and powered from the same supply.
VDDIO and AVSS can be sequenced in any order. Always
perform a reset operation after all the supplies are brought
up to place the device in a known operating state.
Layout Considerations
Digital and AC transient signals on AGND inputs can
create noise at the outputs. Connect both AGND inputs
to form the star ground for the DAC system. Refer remote
DAC loads to this system ground for the best possible
performance (see the Force/Sense section).
Use proper grounding techniques, such as a multilayer
board with a low-inductance ground plane, or star connect all ground return paths back to AGND. Do not use
wire-wrapped boards and sockets. Use ground plane
shielding to improve noise immunity. Do not run analog
and digital signals parallel to one another (especially
clock signals) and avoid routing digital lines underneath
the device package.
For a recommended layout, consult the MAX5318
Evaluation Kit datasheet.
3k
1k
3k
1k
100
IMPEDANCE (I)
IMPEDANCE (I)
100
10nF
10nF
10
100nF
1
1µF
100m
10m
4m
100k
1M
100nF
1
1µF
100m
10M
FREQUENCY (Hz)
Figure 10. Typical X5R Capacitor Impedance
Maxim Integrated
10nF
10
100M
10m
4m
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 11. Typical X5R Capacitor Impedance with Additional
2nH PCB Trace Inductance
37
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Voltage Reference Selection and Layout
The voltage reference should be placed close to the DAC.
The same power-supply decoupling and grounding rules
as the DAC should be implemented. Many voltage references require an output capacitor for stability or noise
reduction. Provided the trace between the reference
device and the DAC is kept short and well shielded, a single capacitor may be used and placed close to the DAC.
However, for improved noise immunity, additional capacitors may be used but be careful not to exceed the recommended capacitance range for the voltage reference.
Refer to Maxim Applications Note AN4300: Calculating
the Error Budget in Precision Digital-to-Analog Converter
(DAC) Applications for detailed description of voltage
reference parameters and trading off the error budget.
The MAX6126 is recommended for use with this device.
the exact point at which the DAC update occurs is then
determined internally as indicated by the BUSY line rising
edge. This is not an exact time.
BUSY Line Pullup Resistor Selection
The BUSY pin is an open-drain output. It therefore
requires a pullup resistor. 2kI value is recommended as
a compromise between power and speed. Stray capacitance on this line can easily slow the rise time to an
unacceptable level. The BUSY pin can sink up to 5mA.
Therefore a resistor as low as VDDIO/0.005 may be used
if faster rise times are required.
Producing Unipolar High-Voltage
and Bipolar Outputs
Figure 11 and Figure 12 show how external op amps can
be used to produce a unipolar high-voltage output and
a bipolar output
Optimizing Data Throughput Rate
The LDAC and BUSY Interaction section details the timing of data written to the device and how the DAC is
updated. Data throughput speed can be increased by
overlapping the data load time with the calibration and
settling time as shown below in Figure 12. Following the
24th SCLK falling edge, the device starts its calibration
period. Providing that the LDAC falling edge arrives
before the 24th SCLK falling edge, and assuming the SPI
clock frequency is high enough, the throughput period is
therefore limited by the internal calculation and settling
times only. A slight further increase in throughput time
can be gained by either toggling LDAC during the calculation time or by pulling it low permanently. However,
Definitions
Integral Nonlinearity (INL)
INL is the deviation of the measured transfer function from
a straight line drawn between two codes. This line is drawn
between the zero and full-scale codes of the transfer function, once offset and gain errors have been nullified.
Differential Nonlinearity (DNL)
DNL is the difference between an actual step height and
the ideal value of 1 LSB. If the magnitude of the DNL is
less than or equal to 1 LSB, the DAC guarantees no missing codes and is monotonic.
24TH SCLK
24TH SCLK
DIN
BUSY
tBUSY
LDAC
LDAC FALLING EDGE BEFORE 24TH SCLK FALLING EDGE
OUT
Figure 12. Optimum Throughput with Stable Update Period
Maxim Integrated
38
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Offset Error
Digital Feedthrough
Offset error indicates how well the actual transfer function matches the ideal transfer function at a single point.
Typically, the point at which the offset error is specified
is at or near the zero-scale point of the transfer function.
Digital feedthrough is the amount of noise that appears
on the DAC output when the DAC digital control lines are
toggled.
Gain Error
The glitch impulse occurs at the major carry transitions
along the segmented bit boundaries. It is specified as the
net area of the glitch impulse which appears at the output
when the digital input code changes by 1 LSB. The glitch
impulse is specified in nanovolts-seconds (nV-s).
Settling Time
The digital-to-analog power-up glitch is the net area of
the glitch impulse which appears at the output when the
device exits power-down mode.
Gain error is the difference between the ideal and the
actual full-scale output voltage on the transfer curve,
after nullifying the offset error. This error alters the slope
of the transfer function and corresponds to the same
percentage error in each step.
The settling time is the amount of time required from the
start of a LDAC high-to-low transition or BUSY low-to-high
transition (whichever occurs last), until the DAC output
settles to within 0.003% of the final value.
Digital-to-Analog Glitch Impulse
Digital-to-Analog Power-Up Glitch Impulse
MAX44250
MAX5318
MAX9632
OUT
-VREF
TO
VREF
OUT
0V TO KVREF
K = 1 + R2 /R1
MAX5318
R1
R1
R2
R2
REFO
R1 = R2
Figure 13. Unipolar High-Voltage Output
Maxim Integrated
Figure 14. Bipolar Output
39
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Typical Operating Circuit
2.4V TO (VAVDD - 0.1V)
0.1µF
2.0kI
BUSY
4
M/Z
3
2.7V TO 5V
MBR0530T1G
1.8V TO 5V
0.01µF
1µF
0.1µF
10µF
VDDIO
REF
BYPASS
AVDD2
AVDD1
24
18
22
21
14
0.1µF
LINEAR
REGULATOR
TS/SB 10
GPIO’s
µC
PD 11
RST
1
LDAC
5
READY
2
CS
9
SCLK
SPI
INTERFACE
7
DOUT
6
17 REFO
BUFFER
100pF
MAX5318
INTERFACE
AND
CONTROL
16 RFB
INPUT
REGISTER
8
DIN
10µF
DIGITAL GAIN
AND OFFSET
DAC
REGISTER
18-BIT
DAC
OUTPUT
BUFFER
15 OUT
RL
13
23
DGND
AGND
19
AGND_S
12
20
AVSS
AGND_F
0.1µF
0 TO -1.25V
Ordering Information
PART
MAX5318GUG+
TEMP RANGE
PIN-PACKAGE
-40NC to +105NC
24 TSSOP
+Denotes a lead(Pb)-free/RoHS-compliant package.
Chip Information
PROCESS: BiCMOS
Maxim Integrated
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
24 TSSOP
U24+1
21-0066
90-0118
40
MAX5318
18-Bit, High-Accuracy Voltage Output DAC with
Digital Gain, Offset Control, and SPI Interface
Revision History
REVISION
NUMBER
REVISION
DATE
0
9/12
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2012
Maxim Integrated
41
The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc.