DATA SHEET GPJ2500~GPJ2510 GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE 50 to 1000 Volts CURRENT 25 Amperes FEATURES • Plastic material has Underwriters Laboratory Flammability Classification 94V-O • Ideal for printed circuit board • Surge overload rating: 350 Amperes peak • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension • Pb free product are available : 99% Sn can meet Rohs environment substance directive request MECHANICALDATA Case: Reliable low cost construction utilizing molded plastic technique Terminals: Leads solderable per MIL-STD-750, Method 2026 Mounting position: Any Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. PA RA M E TE R S YM B O L G P J 2 5 0 0 G P J 2 5 0 1 G P J 2 5 0 2 G P J 2 5 0 4 G P J 2 5 0 6 G P J 2 5 0 8 G P J 2 5 1 0 U N I T S M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e V RRM 50 100 200 400 600 800 1000 V M a x i m u m R M S B r i d g e In p u t V o l t a g e V RMS 35 70 140 280 420 560 700 V M a xi m um D C B l o c k i ng V o l t a g e V DC 50 100 200 400 600 800 100 V M a xi m um A ve r a g e F o r w a r d T C = 1 0 0 OC N O T E S 3 R e c t i f i e d O ut p ut C ur r e nt a t T A = 2 5 OC M O T E S 2 IF (AV ) 25 3 .5 A I2 t 500 A2Sec IF S M 350 A M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 1 2 . 5 A VF 1 .1 V M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ TA = 2 5 O C D c B l o c k i ng Vo l t a g e @ TC = 1 2 5 O C IR 10 350 µA RθJ A RθJ C 22 1 T J ,T S TG -5 0 to + 1 5 0 I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s ) P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 ) (No te 3 ) O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e O C /W O C NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. REV.0-APR.18.2005 PAGE . 1 Ratings and Characteristic Curves (T A=25 OC unless otherwise noted) 400 Average Forward Output Current (A) 30 Peak Forward Surge Current (A) Heat - Sink Mounting, Tc 25 20 15 10 P.C.B Mounting 5 350 300 200 150 100 50 0 1.0 Cycle 0 0 25 50 75 100 125 150 10 1 FIG.2-Maximum Non-Repetitive Peak Forward Surge Current Per Leg FIG.1-Derating Curve Output Rectified Current 1000 Instanta neous Revers e Current ( m A) Instantaneous Forward Current (V) 100 10 O T A=125 C 100 1 0.1 0.01 0.6 0.8 1 1.2 10 1 O T A=25 C 0.1 1.4 0 20 40 60 80 100 Percent of Rated Peak Reverse Voltage (%) Instantaneous Forward Voltage (V) FIG.4-Typical Reverse Characteristics Per Leg FIG.3-Typical Forward Characteristics Per Leg 10 Transient Thermal Impedance ( OC/W) 1000 Junction Capacitance (pF) 100 Number of Cycles at 60Hz O Temperature ( C) 100 10 1 1 10 Reverse Voltage(V) FIG.5-Typical Junction Capacitance Per Leg REV.0-APR.18.2005 100 1 0.1 0.01 0.1 1 10 t, t , Heating Time (sec) FIG.6-Typical Transient Thermal Impedance PAGE . 2