HV9910 Universal High Brightness LED Driver Description Features The HV9910 is a PWM high-efficiency LED driver control IC. It allows efficient operation of High Brightness (HB) LEDs from voltage sources ranging from 8VDC up to 450VDC. The HV9910 controls an external MOSFET at fixed switching frequency up to 300kHz. The frequency can be programmed using a single resistor. The LED string is driven at constant current rather than constant voltage, thus providing constant light output and enhanced reliability. The output current can be programmed between a few milliamps and up to more than 1.0A. >90% Efficiency 8V to 450V input range Constant-current LED driver Applications from a few mA to more than 1A Output LED string from one to hundreds of diodes PWM Low-Frequency Dimming via Enable pin Input Voltage Surge ratings up to 450V HV9910 uses a rugged high voltage junction isolated process that can withstand an input voltage surge of up to 450V. Output current to an LED string can be programmed to any value between zero and its maximum value by applying an external control voltage at the linear dimming control input of the HV9910. The HV9910 provides a low-frequency PWM dimming input that can accept an external control signal with a duty ratio of 0-100% and a frequency of up to a few kilohertz. Applications DC/DC or AC/DC LED Driver applications RGB Backlighting LED Driver Back Lighting of Flat Panel Displays General purpose constant current source Signage and Decorative LED Lighting Automotive Chargers Typical Application C110504 1 C110504 HV9910 Ordering Information Package Options DIP-8 HV9910P SO-16 HV9910NG SO-8 HV9910LG Absolute Maximum Ratings VIN to GND ...................................….........................-0.5V to +470V CS.....................…………………………………...-0.3V to Vdd + 0.3V LD, PWM_D to GND...........……........…............-0.3V to (Vdd ---0.3V) GATE to GND .................................………......-0.3V to (Vdd + 0.3V) VDDMAX…………………………………………………………..……13.5V Continuous Power Dissipation (TA = +25°C) (Note 1) 16-Pin SO (derate 7.5mW/°C above +25°C).…...…….….....750mW 8-Pin DIP (derate 9mW/°C above +25°C)…..……..…….......900mW 8-Pin SO (derate 6.3mW/°C above +25°C)…..……..…….....630mW Operating Temperature Range ...................……......-40°C to +85°C Junction Temperature....................................……….............+125°C Storage Temperature Range .......................……...-65°C to +150°C Stresses beyond those listed under ‘‘Absolute Maximum Ratings’’ may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Specifications Symbol VINDC Description Min Input DC supply voltage range 8.0 IINsd Shut-Down mode supply current VDD Internally regulated voltage VDDmax VDD current available for external circuitry UVLO VDD undervoltage lockout threshold ∆UVLO VDD undervoltage lockout hysteresis VEN(lo) Pin PWM_D input low voltage VEN(hi) Pin PWM_D input high voltage REN 7.0 Typ Max Units 450 V 0.5 1 mA 7.5 8.0 V 13.5 V 1.0 mA Maximal pin Vdd voltage IDD(ext) VCS(hi) 1 6.45 6.7 6.95 500 1.0 2.4 Conditions DC input voltage Pin PWM_D to GND, VIN = 8V VIN = 8–450V, IDD(ext)=0, pin Gate open When an external voltage applied to pin Vdd VIN = 8–100V V Vin rising mV Vin falling V VIN = 8–450V V VIN = 8–450V Pin PWM_D pull-down resistance 50 100 150 kΩ VEN = 5V Current sense pull-in threshold voltage 225 250 275 mV @TA = -40°C to +85°C VGATE(hi) GATE high output voltage VDD-0.3 VDD V IOUT = 10mA VGATE(lo) GATE low output voltage 0 0.3 V IOUT = -10mA Oscillator frequency 20 80 30 120 kHz kHz 100 % FPWMhf = 25kHz, at GATE, CS to GND. GBD 250 mV @TA = <85°C, Vin = 12V 280 ns VCS = 0.55VLD, VLD = VDD 300 ns Vin = 12V, VLD = 0.15, VCS = 0 to 0.22V after TBLANK fOSC DMAXhf VLD 1 (TA = 25°C unless noted otherwise) 25 100 Maximum Oscillator PWM Duty Cycle Linear Dimming pin voltage range 0 150 215 ROSC = 1.00MΩ ROSC = 226kΩ TBLANK Current sense blanking interval tDELAY Delay from CS trip to GATE lo tRISE GATE output rise time 30 50 ns CGATE = 500pF tFALL GATE output fall time 30 50 ns CGATE = 500pF Also limited by package power dissipation limit, whichever is lower. 2 C110504 HV9910 Pinout Description SO-16 Name VIN CS GND GATE 1 4 5 8 SO-8 DIP-8 1 2 3 4 PWM_D 9 5 VDD 12 6 LD 13 7 ROSC 14 8 Input voltage 8V to 450V DC Senses LED string current Device ground Drives the gate of the external MOSFET Low Frequency PWM Dimming pin, also Enable input. Internal 100kΩ pull-down to GND Internally regulated supply voltage. 7.5V nominal. Can supply up to 1mA for external circuitry. A sufficient storage capacitor is used to provide storage when the rectified AC input is near the zero crossings. Linear Dimming by changing the current limit threshold at current sense comparator Oscillator control. A resistor connected between this pin and ground sets the PWM frequency. 8-Pin DIP/SOIC No Connects (NC) are not internally connected and may be used for pass-thru PCB traces. 16-Pin SOIC Block Diagram & Typical Application 3 C110504 HV9910 the sense resistor is applied to the CS pin of the HV9910. When the voltage at CS pin exceeds a peak current sense voltage threshold, the gate drive signal terminates, and the power MOSFET turns off. The threshold is internally set to 250mV, or it can be programmed externally by applying voltage to the LD pin. When soft start is required, a capacitor can be connected to the LD pin to allow this voltage to ramp at a desired rate, therefore, assuring that output current of the LED ramps gradually. Application Information AC/DC Off-Line Applications The HV9910 is a low-cost off-line buck, boost or buck-boost converter control IC specifically designed for driving multi-LED stings or arrays. It can be operated from either universal AC line or any DC voltage between 8-450V. Optionally, a passive power factor correction circuit can be used in order to pass the AC harmonic limits set by EN 61000-3-2 Class C for lighting equipment having input power less than 25W. The HV9910 can drive up to hundreds of High-Brightness (HB) LEDs or multiple strings of HB LEDs. The LED arrays can be configured as a series or series/parallel connection. The HV9910 regulates constant current that ensures controlled brightness and spectrum of the LEDs, and extends their lifetime. The HV9910 features an enable pin (PWM_D) that allows PWM control of brightness. Optionally, a simple passive power factor correction circuit, consisting of 3 diodes and 2 capacitors, can be added as shown in the application circuit diagram of Figure 1. Supply Current A current of 1mA is needed to start the HV9910. As shown in block diagram, this current is internally generated in HV9910 without using bulky startup resistors typically required in the offline applications. Moreover, in many applications the HV9910 can be continuously powered using its internal linear regulator that provides a regulated voltage of 7.5V for all internal circuits. The HV9910 can also control brightness of LEDs by programming continuous output current of the LED driver (so-called linear dimming) when a control voltage is applied to the LD pin. The HV9910 is offered in standard 8-pin SOIC and DIP packages. It is also available in a high voltage rated SO-16 package for applications that require VIN greater than 250V. Setting Light Output When the buck converter topology of Figure 1 is selected, the peak CS voltage is a good representation of the average current in the LED. However, there is a certain error associated with this current sensing method that needs to be accounted for. This error is introduced by the difference between the peak and the average current in the inductor. For example if the peak-topeak ripple current in the inductor is 150mA, to get a 500mA LED current, the sense resistor should be 250mV/(500mA+ 0.5*150mA)=0.43Ω. The HV9910 includes an internal high-voltage linear regulator that powers all internal circuits and can also serve as a bias supply for low voltage external circuitry. LED Driver Operation The HV9910 can control all basic types of converters, isolated or non-isolated, operating in continuous or discontinuous conduction mode. When the gate signal enhances the external power MOSFET, the LED driver stores the input energy in an inductor or in the primary inductance of a transformer and, depending on the converter type, may partially deliver the energy directly to LEDs The energy stored in the magnetic component is further delivered to the output during the off-cycle of the power MOSFET producing current through the string of LEDs (Flyback mode of operation). Dimming Dimming can be accomplished in two ways, separately or combined, depending on the application. Light output of the LED can be controlled either by linear change of its current, or by switching the current on and off while maintaining it constant. The second dimming method (so-called PWM dimming) controls the LED brightness by varying the duty ratio of the output current. When the voltage at the VDD pin exceeds the UVLO threshold the gate drive is enabled. The output current is controlled by means of limiting peak current in the external power MOSFET. A current sense resistor is connected in series with the source terminal of the MOSFET. The voltage from The linear dimming can be implemented by applying a control voltage from 0 to 250mV to the LD pin. This control voltage overrides the internally set 250mV threshold level of the CS pin and programs the output current accordingly. For 4 C110504 HV9910 example, a potentiometer connected between VDD and ground can program the control voltage at the CS pin. Applying a control voltage higher than 250mV will not change the output current setting. When higher current is desired, select a smaller sense resistor. The PWM dimming scheme can be implemented by applying an external PWM signal to the PWM_D pin. The PWM signal can be generated by a microcontroller or a pulse generator with a duty cycle proportional to the amount of desired light output. This signal enables and disables the converter modulating the LED current in the PWM fashion. In this mode, LED current can be in one of the two states: zero or the nominal current set by the current sense resistor. It is not possible to use this method to achieve average brightness levels higher than the one set by the current sense threshold level of the HV9910. By using the PWM control method of the HV9910, the light output can be adjusted between zero and 100%. The accuracy of the PWM dimming method is limited only by the minimum gate pulse width, which is a fraction of a percent of the low frequency duty cycle. 95% PWM Ratio at 500Hz Dimming Some of the typical waveforms illustrating the PWM dimming method used with the application circuit of Figure 1 are given below. CH1 shows the MOSFET Drain voltage, CH2 is the PWM signal to pin PWM_D and CH4 is the current in the LED string. 0.4% PWM Ratio at 500Hz Dimming Programming Operating Frequency The operating frequency of the oscillator is programmed between 25 and 300kHz using an external resistor connected to the ROSC pin: FOSC = 25000/(ROSC [kΩ] + 22) [kHz] Power Factor Correction When the input power to the LED driver does not exceed 25W, a simple passive power factor correction circuit can be added to the HV9910 application circuit of Figure 1 in order to pass the AC line harmonic limits of the EN61000-3-2 standard for Class C equipment. The typical application circuit diagram shows how this can be done without affecting the rest of the circuit significantly. A simple circuit consisting of 3 diodes and 2 capacitors is added across the rectified AC line input to improve the line current harmonic distortion and to achieve a power factor greater than 0.85. 33% PWM Ratio at 500Hz Dimming 5 C110504 HV9910 The required value of the inductor is given by: Inductor Design Referring to the Typical Application Circuit below the value can be calculated from the desired peakto-peak LED ripple current in the inductor. Typically, such ripple current is selected to be 30% of the nominal LED current. In the example given here, the nominal current ILED is 350mA. L = (Vin - VLEDs) * Ton/(0.3 * ILED) = 4.6mH Input Bulk Capacitor An input filter capacitor should be designed to hold the rectified AC voltage above twice the LED string voltage throughout the AC line cycle. Assuming 15% relative voltage ripple across the capacitor, a simplified formula for the minimum value of the bulk input capacitor is given by: The next step is determining the total voltage drop across the LED string. For example, when the string consists of 10 High-Brightness LEDs and each diode has a forward voltage drop of 3.0V at its nominal current; the total LED voltage VLEDS is 30V. Cmin = ILED*VLEDs*0.06/VIN^2 Cmin = 22 µF, a value 22uF/250V can be used. Knowing the nominal rectified input voltage VIN=120V*1.41=169V, the switching duty ratio can be determined, as: A passive PFC circuit at the input requires using two series connected capacitors at the place of calculated CMIN. Each of these identical capacitors should be rated for ½ of the input voltage and have twice as much capacitance. D= VLEDs /VIN=30/169=0.177 Then, given the switching frequency, in this example fosc=50KHz, the required on-time of the MOSFET transistor can be calculated: Enable The HV9910 can be turned off by pulling the PWM_D pin to ground. When disabled, the HV9910 draws quiescent current of less than 1mA. Ton=D/fosc=3.5 microsecond Figure 1: Typical Application Circuit 2A, 250 V 1N4004 coilcraft BUSH-2820R5B 1N4004 BYV26B 68µ F, 160 V AC Input 85-135V AC 0.1µ F, 250 V 1N4004 LEDs VIN VDD 0.1µ F, 250 V 1µF, 10V 1N4004 2R NTC 1n F, 250 V 1n F, 250 V RT HV9910 GATE 1N4004 1N4004 750µΗ , 280 kΩ VN2224 68µ F, 160 V 220nF, 400 V LD CS 0.2 Ω optional for PFC GND PW M_D LED(s) – a string of HB LEDs , 16 diodes 6 C110504 HV9910 Output Open Circuit Protection The output voltage can be either higher or lower than the input voltage, depending on duty ratio. When the buck topology is used, and the LED is connected in series with the inductor, there is no need for any protection against an open circuit condition in the LED string. Open LED connection means no switching and can be continuous. However, in the case of the buck-boost or the Flyback topology the HV9910 may cause excessive voltage stress of the switching transistor and the rectifier diode and potential failure. In this case, the HV9910 can be disabled by pulling the PMW_D pin to ground when the over voltage condition is detected. Let us discuss the above example of an automotive LED driver that needs to drive three HB LEDs at 350mA. Knowing the nominal input voltage VIN=12V, the nominal duty ratio can be determined, as D=VLEDs/(VIN+VLEDs)=9/(12+9)=0.43 Then, given the switching frequency, in this example fOSC=50KHz, the required on-time of the MOSFET transistor can be calculated: DC/DC Low Voltage Applications Ton=D/fOSC=8.6 microsecond The required value of the inductor is given by: Buck Converter Operation The buck power conversion topology can be used when the LED string voltage is needed to be lower than the input supply voltage. The design procedure for a buck LED driver outlined in the previous chapters can be applied to the low voltage LED drivers as well. However, the designer must keep in mind that the input voltage must be maintained higher than 2 times the forward voltage drop across the LEDs. This limitation is related to the output current instability that may develop when the HV9910 buck converter operates at a duty cycle greater than 0.5. This instability reveals itself as an oscillation of the output current at a subharmonic of the switching frequency. L = VIN* Ton/(0.3 * Iled) = 0.98mH, use 1mH Output Capacitor Unlike the buck topology, the buck-boost converter requires an output filter capacitor to deliver power to the LED string during the ON time of switching the transistor, when the Flyback inductor current is diverted from the output of the converter. In order to average the current in the LED, this capacitor must present impedance to the switching output AC ripple current that is much lower than the dynamic impedance ROUT of the LED string. If we assume ROUT=3 Ohm in our example, in order to attenuate the switching ripple by a factor of 10, a capacitor with equivalent series resistance (ESR) of 0.3 Ohm is needed. A chip SMT tantalum capacitor can be selected for this purpose. Flyback (Buck-Boost) Operation This power conversion topology can be used when the forward voltage drop of the LED string is higher, equal or lower than the input supply voltage. For example, the buck-boost topology can be appropriate when input voltage is supplied by an automotive battery (12V) and output string consists of three to six HB LEDs, as the case may be for tail and break signal lights. In the buck-boost converter, the energy from the input source is first stored in the inductor or a Flyback transformer when the switching transistor is ON. The energy is then delivered to the output during the OFF time of the transistor. When the energy stored in the Flyback inductor is not fully depleted by the next switching cycle (continuous conduction mode) the DC conversion between input and output voltage is given by: VOUT = - VIN*D/(1-D) 7 C110504 HV9910 Figure 2 - HV9910 Buck Driver for a single 900mA HB LED (VIN = 8 – 30V) Figure 3 - HV9910 Buck-Boost driver powering 3 to 8, 350mA HB LEDs (VIN = 8 – 30VIN) C110504 Doc. #: DSFPHV9910 8 C110504 Package Outlines 8-LEAD PLASTIC DUAL IN-LINE PACKAGE (P) 0.040 (1.016) T Y P 0.395 max 0.250 ± 0.015 0.250 ± 0.005 0.030 0.110 1 0.300 - 0.320 0.130 ± 0.005 0.020 0.125 min. 0.020 min. 0° - 10°! 0.009 - 0.015 0.018 ± 0.003 0.100 ± 0.010 Note: C ircle (e.g. B ) indicates J E DE C R eference. Doc. #: DSPD8PDP ©2004 S upertex Inc. All rights res erved. Unauthorized us e or reproduction prohibited. 0.325 +0.025 -0.015 Meas urement Legend = Dimens ions in Inches (Dimens ions in Millimeters ) A051004 1235 B ordeaux Drive, S unnyvale, C A 94089 T E L: (408) 222-8888 / F AX : (408) 222-4895 www.s upertex.com Package Outlines 8-LEAD SMALL OUTLINE PACKAGE (LG, TG) (MS-012AA) 0.192 ± 0.005 (4.8895 ± 0.1143) D H 0.236 ± 0.008 (5.9944 ± 0.2032) H1 E 0.154 ± 0.004 (3.9116 ± 0.1016) 0.193 ± 0.012 (4.9022 ± 0.3048) h 7° (4 P LC S ) 0.010 ± 0.002 C (0.254 ± 0.0508) 0.061 ± 0.008 A (1.5494 ± 0.2032) 45° L1 0° - 8 ° e A1 0.007 ± 0.003 (0.1778 ± 0.0762) 0.020 ± 0.009 (0.508 ± 0.2286) 0.050 T Y P. (1.270) B 0.016 ± 0.002 (0.4064 ± 0.0508) Note: C ircle (e.g. B ) indicates J E DE C R eference. Doc. #: DSPD8SOLGTG ©2004 S upertex Inc. All rights res erved. Unauthorized us e or reproduction prohibited. L 0.035 ± 0.015 (0.889 ± 0.381) Meas urement Legend = 0.0275 ± 0.0025 (0.6985 ± 0.0635) Dimens ions in Inches (Dimens ions in Millimeters ) A051004 1235 B ordeaux Drive, S unnyvale, C A 94089 T E L: (408) 222-8888 / F AX : (408) 222-4895 www .s upertex.com Package Outlines 16-LEAD SO PACKAGE (NG) (NARROW BODY) 0.3895 ± 0.0045 (9.8935 ± 0.1145) D 0.156 ± 0.002 (3.962 ± 0.051) 0.2335 ± 0.0105 (5.931 ± 0.267) E H 0.193 ± 0.012 (4.9022 ± 0.3048) 0.350 T Y P. (8.890) 0.500 T Y P. (12.700) D1 A3 0.065 ± 0.004 (1.651 ± 0.102) 0.0255 ± 0.0005 (0.6475 ± 0.0125) 0.009 ± 0.002 C (0.216 ± 0.038) e S 0.050 T Y P. (1.270) 0° - 8 ° 0.059 ± 0.002 (1.499 ± 0.051) B 0.0165 ± 0.0035 (0.4191 ± 0.0889) Note: C ircle (e.g. B ) indicates J E DE C R eference. Doc. #: DSPD16SONG ©2004 S upertex Inc. All rights res erved. Unauthorized us e or reproduction prohibited. A1 0.013 ± 0.004 (0.3302 ± 0.1016) 45° A2 A 0.020 ± 0.002 (0.508 ± 0.0508) h 7° (4 P LC S ) 0.006 ± 0.002 (0.1524 ± 0.0508) 7° (4 P LC S ) L L1 0.033 ± 0.017 (0.8382 ± 0.4318) Meas urement Legend = 0.0275 ± 0.0025 (0.6985 ± 0.0635) Dimens ions in Inches (Dimens ions in Millimeters ) A051004 1235 B ordeaux Drive, S unnyvale, C A 94089 T E L: (408) 222-8888 / F AX : (408) 222-4895 www.s upertex.com