WALL PSMPD65A

PSMPD65 Series
Dual Output
Up to 65 Watts
AC/DC Medical Power Supply
FEATURES
• Medical Application
• Compact Size, Light Weight
• 100% Full Load Burn-In Test
• Universal AC Input/ Full Range
• UL2601-1, EN60601-1 Approved
• Built-In EMI Filter, Low Ripple Noise
• High Efficiency, Low Working Temperature
• Soft-Start Circuit, Limiting AC Surge Current
• Short Circuit, Overload, and Over Voltage Protected
SPECIFICATIONS: PSMPD65 Series
o
All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
INPUT SPECIFICATIONS
Input Voltage
90 – 264VAC (127 – 370VDC)
Input Frequency
47 to 440Hz
AC Current (typical)
1.6A @ 115VAC / 1A @ 230VAC
Inrush Current
20A @ 115VAC cold start / 40A @ 230VAC cold start.
Leakage Current
Less than 0.3mA @ 264VAC
OUTPUT SPECIFICATIONS
Output Voltage
See Table
Output Voltage Tolerance
±4.0% (CH.1) and ±7.0% (CH.2)
Output Adjustment Range
CH1: ±10% rated output voltage.
Output Power (max)
72 Watts with 18CFM min. forced air.
Line Regulation
±1% (CH.1) and ±2% (CH.2)
Load Regulation
±3% (CH.1) and ±4% (CH.2)
Output Current
See Table
Ripple & Noise (20MHz BW)
See Table
Setup, Rise Time
800ms and 20ms at full load and 230VAC.
Hold-Up Time
80ms at full load and 230VAC.
Temperature Coefficient
±0.04%/°C (0~50°C) on +5V output.
PROTECTION
Over Voltage Protection
CH.1 115~135% rated output voltage.
Overload Protection
73~105W hiccup mode, auto-recovery.
GENERAL SPECIFICATIONS
Switching Frequency (fixed)
45KHz
Efficiency
PSMPD-65A: 75% PSMPD-65B: 78%
Isolation Voltage (input to output)
4000VAC for 1 min.
Isolation Voltage (input to field ground)
1500VAC for 1min.
Isolation Resistance
100M/500VDC ohms
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature
-10°C to +55°C (refer to derating curve)
Storage Temperature
-20°C to +85°C (10%~95% RH)
Humidity (non-condensing)
20% to 90% RH
Vibration
10~500Hz, 2G 10min./1cycle, Period for 60 minutes each along X, Y, and Z axes.
MTBF
291,300 hours min.
MIL-HDBK-217 (25°C)
PHYSICAL SPECIFICATIONS
Weight
280g
Dimensions
127(L) x 76(W) x 42(H) mm
SAFETY & EMC
Agency Approvals
UL/ CUL/ TUV/ CB/ CE
Safety Standards
UL2601-1, TUV EN60601-1, IEC601-1 Approved
EMC Standards
EN55011 class B, EN61000-4-2,3,4,5,6,8,11, EN61000-3-2,3, EN60601-1-2, ENV50204
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
PSMPD65 Series
Dual Output
Up to 65 Watts
AC/DC Medical Power Supply
OUTPUT VOLTAGE / CURRENT RATING CHART
Input
Voltage
Model
PSMPD65A
PSMPD65B
Channel 1
Channel 2
Channel 1
Channel 2
90~264VAC
127~370VDC
Output
Voltage
Output Current
Range
Output
Current
Ripple &
Noise
5 VDC
12 VDC
5 VDC
24 VDC
0.4 ~ 7.0A
0.2 ~ 3.2A
0.4 ~ 6A
0.2 ~ 2.6A
5.5A
2.8A
3.5A
2A
60mVp-p
150mVp-p
60mVp-p
150mVp-p
Output
Power
61W
66W
NOTES
1. All parameters are specified at 230VAC input, rated load, 25°C ambient.
2. Tolerances include set up tolerance, line regulation, load regulation.
3. Line regulation is measured from low line to high line at rated load.
4. Mounting holes M1 and M2 should be grounded for EMI purposes.
5. Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uF & 47uF capacitor.
BLOCK DIAGRAM
DERATING CURVE
STATIC CHARACTERISTICS
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797
PSMPD65 Series
Dual Output
Up to 65 Watts
AC/DC Medical Power Supply
MECHANICAL DRAWING
Unit: mm
AC Input Connector (CN1): Molex 5277-02 or equivalent
DC Output Connector (CN2): Molex 5273-06 or equivalent
Pin. No
Assignment
Mating Housing
Terminal
Pin No.
Assignment
1
AC/N
Molex 5194
or equivalent
+V
AC/L
Molex 5195
or equivalent
1
2
2,3
+5V
4,5
COM
6
NC
Mating Housing
Terminal
Molex 5195
or equivalent
Molex 5194
or equivalent
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax 603-778-9797