PSSP100 Series Single Output 100 Watt with PFC Function AC/DC Switching Power Supply FEATURES ● 3 Year Warranty ● Low Cost, High Reliability ● Fixed Switching Frequency ● LED Indicator for Power On ● 100% Full Load Burn-In Tested ● Universal AC Input / Full Range ● Remote ON/OFF Control (Optional) ● Built-In Active PFC Function, PF > 0.93 ● Built-In Constant Current Limiting Circuit ● Soft Start Circuit, Limiting AC Surge Current ● Short Circuit, Overload, and Over Voltage Protected SPECIFICATIONS: PSSP100 Series o All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage Range 85 ~ 264VAC (120 ~ 370VDC) Input Frequency 47 to 63Hz AC Current (typical) 1.7A @ 115VAC 0.8A @ 230VAC Inrush Current (typical) Cold Start 30A @ 230VAC Leakage Current < 2mA @ 240VAC Power Factor (typical) PF > 0.93 @ 230VAC PF > 0.98 @ 115VAC and full load Remote ON/OFF Control (Option) CN1: 4~10VDC Power On, <0 ~ 0.8VDC Power Off OUTPUT SPECIFICATIONS Output Voltage See Table Output Power See Table Voltage Tolerance (See Note 3) 3.3V - 15V outputs: 2.0%; 24V - 48V outputs: 1.0% Voltage Adjustment Range See Table Line Regulation 0.5% Load Regulation 3.3V - 7.5V outputs: 1.0%; 12V - 48V outputs: 0.5% Output Current See Table Ripple & Noise (max) (See Note 2) 3.3V - 15V outputs: 100mVp-p; 24V & 27V outputs: 150mVp-p; 48V output: 250mVp-p Setup, Rise Time 600ms, 30ms @ full load Hold Up Time (typical) 20ms @ full load Temperature Coefficient ±0.05%/°C (0 ~ 50°C) PROTECTION 105 ~ 150% rated output power Overload Protection Protection Type: Constant current limiting; recovers automatically after fault condition is removed See Table Over Voltage Protection Type: Shutdown output voltage, re-power on to recover. GENERAL SPECIFICATIONS Switching Frequency PFC: 67KHz PWM: 134KHz Efficiency (typical) See Table Withstand Voltage 3000VAC (Input to Output), 1500VAC (Input to FG), 500VAC (Output to FG) Isolation Resistance 100MΩ/500DC (Input to Output, Input to FG, and Output to FG) ENVIRONMENTAL SPECIFICATIONS Working Temperature -10°C to +60°C (refer to output load derating curve) Storage Temperature -20°C to +85°C Working Humidity 20 ~ 90% RH non-condensing Storage Humidity 10 ~ 95% RH Vibration 10 ~ 500Hz, 2G 10min./1 cycle, 60min each along X, Y, Z axes. MTBF 211,300 hours min. @ 25°C (MIL-HDBK-217F) PHYSICAL SPECIFICATIONS Weight 600 grams Dimensions 179(L) x 99(W) x 45(H) mm Warranty 3 years SAFETY & EMC Safety Standards UL60950-1, TUV EN60950-1 approved EMI Conduction & Radiation Compliance to EN55022 (CISPR22) Class B Harmonic Current Compliance to EN61000-3-2,-3 EMS Immunity Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSSP100 Series Single Output 100 Watt with PFC Function AC/DC Switching Power Supply OUTPUT VOLTAGE / CURRENT RATING CHART Model Number Input Voltage PSSP100-3.3 PSSP100-5 PSSP100-7.5 PSSP100-12 Output Voltage 3.3 VDC Voltage Adjust. Range 3.14 ~ 3.63V Over Voltage Protection 3.63 ~ 4.46V Output Current 20A 5 VDC 4.75 ~ 5.5V 5.5 ~ 6.75V 7.5 VDC 7.13 ~ 8.25V Output Power Efficiency 66W 70% 20A 100W 76% 8.25 ~ 10.13V 13.5A 101.25W 78% 12 VDC 11.4 ~ 13.2V 13.2 ~ 16.2V 8.5A 102W 80% 13.5 VDC 12.8 ~ 14.9V 14.85 ~ 18.23V 7.5A 101.25W 80% 15 VDC 14.3 ~ 16.5V 16.5 ~ 20.25V 6.7A 100.5W 82% PSSP100-24 24 VDC 22.8 ~ 26.4V 26.4 ~ 32.4V 4.2A 100.8W 84% PSSP100-27 27VDC 25.7 ~ 29.7V 29.7 ~ 36.45V 3.8A 102.6W 83% PSSP100-48 48 VDC 45.6 ~ 52.8V 52.8 ~ 64.8V 2.1A 100.8W 82% PSSP100-13.5 PSSP100-15 85 ~ 264 VAC (120 ~ 370 VDC) NOTES 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load, and 25°C ambient temperature. 2. Ripple & noise are measured at 20MHz bandwidth by using a 12" twisted pair-wire terminated with a 0.1uF& 47uF parallel capacitor. 3. Tolerances include set up tolerance, line regulation, and load regulation. 4. The power supply is considered a component, which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives. BLOCK DIAGRAM DERATING CURVE OUTPUT DERATING VS INPUT VOLTAGE Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSSP100 Series Single Output 100 Watt with PFC Function AC/DC Switching Power Supply MECHANICAL DRAWING Unit: mm Terminal Pin No. Assignment Pin No. 1 2 3 4,5 6,7 Assignment AC/L AC/N FG DC OUTPUT (-V) DC OUTPUT (+V) Remote ON/OFF (CN1): JST S2B-XH or equivalent (optional) Pin No. 1 2 Assignment RC+ RC- Mating Housing JST XHP or equivalent Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Terminal JST SXH-001T-P0.6 or equivalent