CD 299 PG Series 9 000h at 105°C CD 299 PG CD 29H QH · Extended Lifetime at 105°C · High Ripple Current · High Professional Industrial Power Supplies longest life higher current highest current CD 296 KC longer life CD 297 BB Item Characteristics Operating Temperature Range (°C) -40 ~ +105 Voltage Range (V) 160 ~ 250 -25 ~ +105 315 ~ 450 Capacitance Range (µF) 39 ~ 2 200 Capacitance Tolerance (20°C, 120Hz) ± 20% Leakage Current (µA) After 5 minutes at 20°C application of rated voltage, leakage current is not more than 0,01CV or 1,5mA, whichever is smaller C: Nominal Capacitance (µF) V: Rated Voltage (V) Rated Voltage (V) Dissipation Factor (20°C, 120Hz) 160 180 200 Tan δ (max) Snap-In 315 350 400 0,20 ≤ 250 315 ~ 450 Z -25°C / Z +20°C 3 8 Z -40°C / Z +20°C 12 - Useful Life 9 000h 450 0,15 Rated Voltage (V) Stability at Low Temperature (Impedance Ratio at 120Hz) Lifetime 250 Load Life >200 000h Endurance Test 7 000h Shelf Life 7 000h 1 000h Leakage Current Not more than specified value Not more than specified Not more than specified value value Capacity Change Within ± 30% of initial value Within ± 20% of initial value Within ± 20% of initial value Within ± 20% of initial value Not more than 300% of specified value Not more than 200% of specified value Not more than 130% of specified value Not more than 200% of specified value UR UR UR UR UR = 0 IR 1,4 x IR IR IR = 0 IR = 0 105°C 50°C 105°C 105°C 105°C ≤ 1% Failure Rate ≤ 1% Failure Rate guaranteed Dissipation Factor Condition: Applied Voltage Applied Current Applied Temperature Failure Rate Level Not more than specified value After test: UR to be applied for 30min >24h before measurement Multiplier for Ripple Current Frequency Coefficient Lifetime Diagram 3.0 Frequency 50Hz Rated Voltage (V) 60Hz 120Hz 300Hz 1kHz ≥50kHz IR 160 ~ 250 0,81 0,85 1,00 1,17 1,45 1,50 315 ~ 450 0,77 0,82 1,00 1,16 1,41 1,43 CD 299 PG Series IA ––– 2.5 2.0 1.5 1.0 X32 0.5 0.0 40 X16 X8 X4 X2 X1 Lifetime Multiplier 50 60 70 80 90 100 110 TA (˚C) IA = actual ripple current at 120Hz, IR = rated ripple current at 120Hz, 105°C Multiplier of Useful Life as a function of ambient temperature and ripple current load 58 Direct Contact & Support: Jianghai Europe GmbH +49 (0)2151-652088-0 [email protected] www.jianghai-europe.com v2006.2 CD 299 PG Series Ratings for CD 299 PG Series Rated Capacitance Max ESR 20°C, 120Hz Typ ESR 20°C, 120Hz Max Ripple Current 105°C, 120Hz (V) (µF) (mΩ) (mΩ) (Arms) 270 330 390 470 560 680 160 (200) 2C 820 1 000 1 200 1 500 1 800 2 200 220 330 470 560 180 (225) 2K 680 820 1 000 1 200 1 500 1 800 2 200 220 270 390 470 200 (250) 2D 560 680 820 1 000 1 200 1 500 180 220 270 330 250 (300) 2E 390 470 560 680 820 315 (365) 2F 1 000 1 200 82 100 120 737 603 511 424 424 356 356 293 293 293 243 199 199 166 166 166 133 133 111 111 91 905 603 603 424 424 424 356 356 293 293 293 243 243 243 199 166 166 133 133 111 91 905 737 737 511 511 511 424 424 424 356 293 293 243 243 243 199 199 166 166 133 1 106 905 737 737 737 603 603 511 511 511 424 424 424 356 293 293 243 243 199 166 2 427 1 990 1 658 516 423 358 297 297 249 249 205 205 205 170 140 140 117 117 117 93 93 78 78 64 634 423 423 297 297 297 249 249 205 205 205 170 170 170 140 117 117 93 93 78 64 634 516 516 358 358 358 297 297 297 249 205 205 170 170 170 140 140 117 117 93 774 634 516 516 516 423 423 358 358 358 297 297 297 249 205 205 170 170 140 117 1 335 1 095 912 1,10 1,20 1,30 1,40 1,40 1,50 1,50 1,70 1,70 1,70 2,00 2,20 2,20 2,30 2,30 2,30 2,50 2,50 2,70 2,70 2,90 1,00 1,20 1,20 1,40 1,40 1,40 1,50 1,50 1,70 1,70 1,70 2,00 2,00 2,00 2,20 2,30 2,20 2,50 2,50 2,70 2,90 1,00 1,10 1,10 1,30 1,30 1,30 1,40 1,40 1,40 1,50 1,70 1,70 2,00 2,00 2,00 2,20 2,20 2,30 2,30 2,50 0,90 1,00 1,10 1,10 1,10 1,20 1,20 1,30 1,30 1,30 1,40 1,40 1,40 1,50 1,70 1,70 2,00 2,00 2,20 2,30 0,64 0,69 0,75 Size Ø DxL VDC (Surge Voltage) Code Rated Capacitance Max ESR 20°C, 120Hz Typ ESR 20°C, 120Hz Max Ripple Current 105°C, 120Hz (mm) (V) (µF) (mΩ) (mΩ) (Arms) 22 x 25 22 x 30 25 x 25 22 x 35 25 x 30 22 x 40 30 x 25 22 x 45 25 x 35 30 x 30 25 x 40 25 x 45 30 x 35 25 x 50 30 x 40 35 x 35 30 x 45 35 x 40 30 x 50 35 x 45 35 x 50 22 x 25 22 x 30 25 x 25 22 x 35 25 x 30 30 x 25 22 x 40 25 x 35 22 x 50 25 x 40 30 x 30 25 x 45 30 x 35 35 x 30 30 x 40 30 x 45 35 x 35 30 x 50 35 x 40 35 x 45 35 x 50 22 x 25 22 x 30 25 x 25 22 x 35 25 x 30 30 x 25 22 x 40 25 x 35 30 x 30 22 x 45 25 x 40 30 x 35 25 x 50 30 x 40 35 x 30 30 x 45 35 x 35 30 x 50 35 x 40 35 x 50 22 x 30 25 x 25 22 x 35 25 x 30 30 x 25 22 x 40 25 x 35 22 x 45 25 x 40 30 x 30 25 x 45 30 x 35 35 x 30 25 x 50 30 x 45 35 x 35 30 x 50 35 x 40 35 x 45 35 x 50 22 x 25 22 x 30 25 x 25 150 180 220 315 (365) 2F 270 330 390 470 560 680 82 100 120 150 350 (400) 2V 180 220 270 330 390 560 56 68 82 100 120 150 400 (450) 2G 180 220 270 330 390 470 39 47 56 68 82 450 (500) 2W 100 120 150 180 220 270 330 1 327 1 327 1 327 1 106 1 106 905 905 905 737 737 737 603 603 511 511 424 424 356 293 2 427 1 990 1 990 1 658 1 658 1 327 1 327 1 106 1 106 1 106 905 905 737 737 737 603 603 511 511 356 3 553 2 926 2 926 2 427 1 990 1 658 1 658 1 658 1 327 1 327 1 327 1 106 1 106 1 106 905 905 905 737 737 603 603 511 424 6 802 5 644 4 737 4 737 3 901 3 901 3 235 3 235 3 235 2 653 2 653 2 653 2 211 1 769 1 769 1 769 1 474 1 474 1 206 1 206 983 804 730 730 730 608 608 498 498 498 406 406 406 332 332 281 281 233 233 196 161 1 335 1 095 1 095 912 912 730 730 608 608 608 498 498 406 406 406 332 332 281 281 196 1 954 1 610 1 610 1 335 1 095 912 912 912 730 730 730 608 608 608 498 498 498 406 406 332 332 281 233 3 061 2 540 2 132 2 132 1 756 1 756 1 456 1 456 1 456 1 194 1 194 1 194 995 796 796 796 664 664 543 543 443 362 0,82 0,82 0,82 0,90 0,90 1,00 1,00 1,00 1,10 1,10 1,10 1,20 1,20 1,30 1,30 1,40 1,40 1,50 1,70 0,64 0,69 0,69 0,75 0,75 0,82 0,82 0,90 0,90 0,90 1,00 1,00 1,10 1,10 1,10 1,20 1,20 1,30 1,30 1,50 0,51 0,56 0,56 0,64 0,69 0,75 0,75 0,75 0,82 0,82 0,82 0,90 0,90 0,90 1,00 1,00 1,00 1,10 1,10 1,20 1,20 1,30 1,40 0,37 0,40 0,47 0,47 0,53 0,53 0,56 0,56 0,56 0,64 0,64 0,64 0,72 0,79 0,79 0,79 0,87 0,87 1,00 1,00 1,19 1,38 Size Ø DxL (mm) 22 x 35 25 x 30 30 x 25 22 x 40 25 x 35 22 x 45 25 x 40 30 x 30 25 x 45 30 x 35 35 x 30 25 x 50 30 x 40 30 x 45 35 x 35 30 x 50 35 x 40 35 x 45 35 x 50 22 x 25 22 x 30 25 x 25 22 x 35 25 x 30 22 x 40 30 x 25 22 x 45 25 x 35 30 x 30 22 x 50 25 x 40 25 x 50 30 x 35 35 x 30 30 x 45 35 x 35 30 x 50 35 x 40 35 x 50 22 x 25 22 x 30 25 x 25 22 x 35 25 x 30 22 x 40 25 x 35 30 x 25 22 x 50 25 x 40 30 x 30 25 x 45 30 x 35 35 x 25 25 x 50 30 x 40 35 x 30 30 x 45 35 x 35 30 x 50 35 x 40 35 x 45 35 x 50 22 x 25 22 x 30 22 x 35 25 x 25 22 x 40 25 x 30 22 x 45 25 x 35 30 x 25 22 x 50 25 x 40 30 x 30 25 x 45 25 x 50 30 x 40 35 x 30 30 x 45 35 x 35 30 x 50 35 x 40 35 x 45 35 x 50 Custom products are available on request. Direct Contact & Support: Jianghai Europe GmbH +49 (0)2151-652088-0 [email protected] www.jianghai-europe.com v2006.2 59 Snap-In VDC (Surge Voltage) Code Part Number System Order Code SMD, Radial, Snap-In EC R 1C Technology Terminal Type Rated Voltage Code EC = Electrolytic Capacitor PC = Polymer Capacitor SMD =V Radial = R Snap-In = S For coding please refer to the pages of ratings PT 101 M Series Code Capacitance Code (in µF) Capacitance Tolerance 0,47 = R47 ±20% FF 25 Lead Form Terminal/ Pitch Size = M SMD: 0611 JE xxxxx Dimension for Specials only 4x7 = 0407 CD VS = BS CD VH = VH 1,0 = 010 CD VZ = VZ 2,2 = 2R2 +30 / -10% = Q Radial: CD 261 = LK 100 = 101 Long Lead = LL 2,0mm = 20 35x80 CD 261X = QX 1 000 = 102 Cut 5,0mm = CB 2,5mm = 25 45x100 = 45100 ±10% =K +50 / -10% = T Taped = FF Terminal = T2 5x11,5 = 0511 6,3x11,5= 0611 CD 262 = QM 10 000 = 103 Cut4,5mm = CC 3,5mm = 35 CD 263 = BK Cut 4,0mm = CD 5,0mm = 50 CD 269 = PH Cut 3,5mm = CE 7,5mm = 75 CD 281 = LL Cut 3,0mm = CF 10,0mm = 10 CD 284 = XY CD 287 = GC CD 28L = QL Snap-In: CD 293 = BZ 4,0mm Pin Length = T4 2 Pin CD 294 = BW 6,3mm Pin Length = T6 3 Pin = P3 CD 295 = BC Soldering Pin 4 Pin = P4 CD 296 = KC 5 Pin = P5 CD 297 = BB CD 299 = PG on request: alternative lead forms (axial, 90° - angle, others) = 3580 12,5mm = 12 = S4 = P2 preferred CD 29D = HR CD 29H = QH CD 29L = QL HCP = CP HPM = PM HVC = VC Technical Specification SMD Type Dimensions Ø DxL 4 x 5,4 5 x 5,4 A 1,8 2,1 2,4 2,5 2,9 2,9 3,2 3,2 B 4,3 5,3 6,6 6,6 8,3 8,4 10,3 10,4 C 4,3 5,3 6,6 6,6 8,3 8,4 10,3 10,4 E 1,0 1,3 2,2 2,2 3,1 3,1 4,5 4,5 L 5,4 5,4 5,4 7,7 10,5 11,8 10,5 12,7 W 6,3 x5,4 6,3x 7,7 8 x 10,5 8 x 11,8 10x10,5 10x12,7 0,5 - 0,8 0,7 - 1,1 in mm Taping Dimensions Size (DxL) w ± 0,3 A ± 0,2 B ± 0,2 P ± 0,1 t2 ± 0,2 F ± 0,1 t1 ± 0,1 4 x 5,4 12,0 5,0 5,0 8,0 5,8 5,5 0,4 5 x 5,4 12,0 6,0 6,0 12,0 5,8 5,5 0,4 6,3 x 5,4 16,0 7,0 7,0 12,0 5,8 7,5 0,4 6,3 x 7,7 16,0 7,0 7,0 12,0 8,4 7,5 0,4 8 x 10,5 24,0 8,7 8,7 16,0 11,0 11,5 0,5 8 x 11,8 24,0 8,7 8,7 16,0 12,3 11,5 0,5 10 x 10,5 24,0 10,7 10,7 16,0 11,0 11,5 0,5 10 x 12,7 24,0 10,7 10,7 16,0 14,0 11,5 0,5 in mm Soldering Profile (Aluminium Electrolytic Capacitors) Diameter w D 4; 5 14 ± 1 50 ± 1 6,3 18 ± 1 50 ± 1 8; 10 25 ± 1 50 ± 1 Polymer 25 ± 1 80 ± 1 in mm Allowable Range of Peak Temperature Size T (°C) t (second) t 1 (second) Ø 4 ~ 6,3 Ø 8 x 10,5 Ø 10 x 10,5 250 240 235 90 90 60 40 30 30 For more details or Soldering Profiles of Radials or Polymer-Capacitors please contact our local Sales Offices. Direct Contact & Support: Jianghai Europe GmbH +49 (0)2151-652088-0 [email protected] www.jianghai-europe.com v2006.2 Part Number System Technical Specification Snap-In Type Pin Type: Snap-In Order Code: T6, T4 Pin Type: Soldering Order Code: S4 T6, T4 S4 Terminal T6 T4 Pin Length T 6,3 4,0 Snap-In Terminal Order Code: P2, P3, P4 Soldering Terminal Order Code: P5 P2 P3 P4 P5 Positive Negative Terminal Negative Negative Mounting Holes Mounting Holes Mounting Holes P3 only T4 Terminal Order Code Screw Type EC G Technology Terminal Type 1C BP Rated Voltage Series Code Code 101 M Capacitance Code Capacitance Tolerance CD 135 = BP 100 = 101 EC = Electrolytic Screw = G For coding Capacitor please refer CD 136 = PK 1 000 = 102 to the pages CD 137 = PX 10 000 = 103 of ratings CD 138 = PC CD 139 = BL B E Mounting 160 A361 JExxxxx For Terminal Code see tables below for Specials only Diameter Length ±20% = M Bolt =B 36 = A 53 = 053 ±10% = K No double sleeve =N 40 = B 65 = 065 +30 / -10%= Q 2 stoppers bracket+double sleeve* = I 51 = C 96 = 096 +20 / -0% = R 3 stoppers bracket+double sleeve* = Y 64 = D 100 = 100 +50 / -10%= T No bracket, but double sleeve* 77 = E 115 = 115 preferred =D * Double sleeve for diameter ≥ 51 only 90 = F 236 = 236 101 = G Technical Specification Screw Type Dimensions Standard Housing Order Code: I, Y, D, N Bolt Housing Order Code: B ØD Ød l Ø 36 M8 12 ≥ Ø 51 M12 16 in mm 10 Direct Contact & Support: Jianghai Europe GmbH +49 (0)2151-652088-0 [email protected] www.jianghai-europe.com v2006.2