Plastic Infrared Emitting Diode OP240 Series OP245 Series Features: • • • • Wide irradiance pattern Side-looking package for space-limited applications Wavelength matched to silicon’s peak response Mechanically and spectrally matched to other OPTEK products OP240 OP245 Description: Each device in this series is a high intensity gallium aluminum arsenide infrared emitting diode that is suited for use as a PCBoard mounted slotted switch or an easy mount PCBoard interrupter. Each dome lens OP240 and OP245 device is an 890 nm diode that is molded in an IR-transmissive clear epoxy side-looking package. OP240 is mechanically and spectrally matched to the OP550 and OP560 series of phototransistors. OP245 is mechanically and spectrally matched to the OP555 and OP565 series devices. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Applications: • • • Ordering Information Space-limited applications PCBoard mounted slotted switch PCBoard interrupter OP240 (A, B, C, D) Part Number OP240A OP240B OP240C OP240D OP245A OP245B OP245C OP245D LED Peak Wavelength Lens Type Total Beam Angle Lead Length 40° 0.50" minimum Dome 890 nm Recessed 1 2 DIMENSIONS ARE IN: [MILLIMETERS] INCHES Pin # LED 1 2 Cathode Anode CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK'S molded plastics. RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.1 01/07 Page 1 of 3 Plastic Infrared Emitting Diode OP240 Series OP245 Series OP245 (A, B, C, D) 1 Pin # LED 1 2 Cathode Anode 2 CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries’ Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK'S molded plastics. DIMENSIONS ARE IN: [MILLIMETERS] INCHES Absolute Maximum Ratings (TA=25°C unless otherwise noted) -40o C to +100o C Storage and Operating Temperature Range 2.0 V Reverse Voltage Continuous Forward Current 50 mA Peak Forward Current 3.0 A 260° C(1) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 100 mW(2) Power Dissipation Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX Apertured Radiant Incidence OP240A, OP245A OP240B, OP245B OP240C, OP245C OP240D, OP245D 0.60 0.40 0.20 0.05 - 1.20 0.86 - UNITS TEST CONDITIONS Input Diode EE (APT) mW/cm2 IF = 20 mA(3) VF Forward Voltage - - 1.80 V IF = 20 mA IR Reverse Current - - 100 µA VR= 2.0 V λP Wavelength at Peak Emission - 890 - nm IF = 10 mA B Spectral Bandwidth between Half Power Points - 80 - nm IF = 10 mA Spectral Shift with Temperature - ±0.18 - nm/°C Emission Angle at Half Power Points - 40 - Degree IF = 20 mA tr Output Rise Time - 500 - ns tf Output Fall Time - 250 - ns ∆λP /∆T θHP IF = Constant IF(PK)=100 mA, PW=10 µs, and D.C.=10.0% Notes: 1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. A maximum of 20 grams force may be applied to the leads when soldering. 2. Derate linearly 1.33 mW/° C above 25° C. 3. EE(APT) is a measurement of the average apertured radiant energy incident upon a sensing area 0.180” (4.57 mm) in diameter perpendicular to and centered on the mechanical axis of the lens and 0.653” (6.60 mm) from the lens tip. EE(APT) is not necessarily uniform within the measured area. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.1 01/07 Page 2 of 3 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Plastic Infrared Emitting Diode OP240 Series OP245 Series OP240, OP245 (A, B, C, D) Forward Voltage vs Forward Current vs Temperature Optical Power vs IF vs Temp 4.0 1.8 Normalized at 20 mA and 20o C 1.7 3.5 -65°C -40°C -20°C +0°C +20°C +40°C +60°C +80°C +100°C +125°C 3.0 Normalized Optical Power Typical Forward Voltage (V) 1.6 1.5 1.4 1.3 -65°C -40°C -20°C +0°C +20°C +40°C +60°C +80°C +100°C +125°C 1.2 1.1 1.0 2.5 2.0 1.5 1.0 0.5 0.9 0.0 0 5 10 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 50 Forward Current IF (mA) Forward Current (mA) Distance vs Output Power vs Forward Current Beam Angle 9 110% Normalized at 0.6" and 50 mA 100% 8 Forward Current 90% 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 80 mA 100 mA 6 5 80% Normalized Radiance Normalized Output Power 7 4 3 70% 60% 50% 40% 30% 2 20% 1 10% 0 0% 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 -80 -70 -60 -50 -40 -30 -20 -10 0 Distance (inches) 10 20 30 40 50 60 70 80 Degrees OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue A.1 01/07 Page 3 of 3