FAIRCHILD 74VHC132

74VHC132
QUAD 2-INPUT SCHMITT NAND GATE
■
■
■
■
■
■
■
■
■
■
HIGH SPEED: tPD = 3.9 ns (TYP.) at VCC = 5V
LOW POWER DISSIPATION:
ICC = 2 µA (MAX.) at TA=25°C
TYPICAL HYSTERESIS:
Vh = 1V at VCC = 4.5V
POWER DOWN PROTECTION ON INPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 8 mA (MIN)
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
OPERATING VOLTAGE RANGE:
VCC(OPR) = 2V to 5.5V
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 132
IMPROVED LATCH-UP IMMUNITY
LOW NOISE: VOLP = 0.8V (MAX.)
DESCRIPTION
The 74VHC132 is an advanced high-speed
CMOS QUAD 2-INPUT SCHMITT NAND GATE
fabricated with sub-micron silicon gate and
double-layer metal wiring C2MOS technology.
Power down protection is provided on all inputs
and 0 to 7V can be accepted on inputs with no
regard to the supply voltage. This device can be
used to interface 5V to 3V.
SOP
TSSOP
Table 1: Order Codes
PACKAGE
T&R
SOP
TSSOP
74VHC132MTR
74VHC132TTR
Pin configuration and function are the same as
those of the 74VHC00 but the 74VHC132 has
hysteresis.
This together with its schmitt trigger function
allows it to be used on line receivers with slow
rise/fall input signals.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
Figure 1: Pin Connection And IEC Logic Symbols
November 2004
Rev. 4
1/11
74VHC132
Figure 2: Input Equivalent Circuit
Table 2: Pin Description
PIN N°
SYMBOL
1, 4, 9, 12
2, 5, 10, 13
3, 6, 8, 11
7
1A to 4A
1B to 4B
1Y to 4Y
GND
VCC
14
NAME AND FUNCTION
Data Inputs
Data Inputs
Data Outputs
Ground (0V)
Positive Supply Voltage
Table 3: Truth Table
A
B
Y
L
L
H
H
L
H
L
H
H
H
H
L
Table 4: Absolute Maximum Ratings
Symbol
VCC
Parameter
Supply Voltage
VI
DC Input Voltage
VO
DC Output Voltage
IIK
Value
Unit
-0.5 to +7.0
V
-0.5 to +7.0
V
-0.5 to VCC + 0.5
V
DC Input Diode Current
- 20
mA
IOK
DC Output Diode Current
± 20
mA
IO
DC Output Current
ICC or IGND DC VCC or Ground Current
Storage Temperature
Tstg
TL
Lead Temperature (10 sec)
± 25
mA
± 50
mA
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
Table 5: Recommended Operating Conditions
Symbol
VCC
2/11
Parameter
Supply Voltage
Value
Unit
2 to 5.5
V
VI
Input Voltage
0 to 5.5
V
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
-55 to 125
°C
74VHC132
Table 6: DC Specifications
Test Condition
Symbol
Vt+
Vt-
Vh
VOH
VOL
II
ICC
Parameter
High Level
Threshold Voltage
Low Level
Threshold Voltage
Hysteresis Voltage
High Level Output
Voltage
Low Level Output
Voltage
Input Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
3.0
4.5
5.5
3.0
4.5
5.5
3.0
4.5
5.5
Typ.
Max.
2.2
3.15
3.85
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
2.2
3.15
3.85
0.9
1.35
1.65
1.2
1.4
1.6
0.3
0.4
0.5
0.3
0.4
0.5
Max.
2.2
3.15
3.85
0.9
1.35
1.65
1.2
1.4
1.6
0.3
0.4
0.5
Unit
V
0.9
1.35
1.65
1.2
1.4
1.6
V
V
2.0
IO=-50 µA
1.9
2.0
1.9
1.9
3.0
IO=-50 µA
2.9
3.0
2.9
2.9
4.5
IO=-50 µA
4.4
4.5
3.0
IO=-4 mA
2.58
4.5
IO=-8 mA
3.94
2.0
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=50 µA
0.0
0.1
0.1
0.1
4.5
IO=50 µA
0.0
0.1
0.1
0.1
3.0
IO=4 mA
0.36
0.44
0.55
4.5
IO=8 mA
0.36
0.44
0.55
0 to
5.5
VI = 5.5V or GND
± 0.1
±1
±1
µA
5.5
VI = VCC or GND
2
20
20
µA
4.4
4.4
2.48
2.4
3.8
V
3.7
V
Table 7: AC Electrical Characteristics (Input tr = tf = 3ns)
Test Condition
Symbol
Parameter
VCC
(V)
CL
(pF)
tPLH
tPHL
Propagation Delay
Time
3.3(*)
3.3(*)
(**)
5.0(**)
5.0
Value
TA = 25°C
Min.
-40 to 85°C
-55 to 125°C
Typ.
Max.
Min.
Max.
Min.
Max.
15
5.6
11.9
1.0
14.0
1.0
14.0
50
7.6
15.4
1.0
17.5
1.0
17.5
15
3.9
7.7
1.0
9.0
1.0
9.0
50
5.3
9.7
1.0
11.0
1.0
11.0
Unit
ns
(*) Voltage range is 3.3V ± 0.3V
(**) Voltage range is 5.0V ± 0.5V
3/11
74VHC132
Table 8: Capacitive Characteristics
Test Condition
Symbol
Value
TA = 25°C
Parameter
Min.
Typ.
Max.
10
CIN
Input Capacitance
6
CPD
Power Dissipation
Capacitance
(note 1)
16
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
10
Unit
Max.
10
pF
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per gate)
Table 9: Dynamic Switching Characteristics
Test Condition
Symbol
VOLP
VOLV
VIHD
VILD
Parameter
Dynamic Low
Voltage Quiet
Output (note 1, 2)
Dynamic High
Voltage Input
(note 1, 3)
Dynamic Low
Voltage Input
(note 1, 3)
TA = 25°C
VCC
(V)
Min.
5.0
5.0
Value
-0.8
CL = 50 pF
5.0
Typ.
Max.
0.3
0.8
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
Unit
Max.
V
-0.3
3.5
V
1.5
V
1) Worst case package.
2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND.
3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold
(VIHD), f=1MHz.
Figure 3: Test Circuit
CL =15/50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
4/11
74VHC132
Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle)
5/11
74VHC132
SO-14 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
1.35
1.75
0.053
0.069
A1
0.1
0.25
0.004
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
8.55
8.75
0.337
0.344
E
3.8
4.0
0.150
0.157
e
1.27
0.050
H
5.8
6.2
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.4
1.27
0.016
0.050
k
0°
8°
0°
8°
ddd
0.100
0.004
0016019D
6/11
74VHC132
TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
MAX.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0˚
L
0.45
A
0.60
0.0256 BSC
8˚
0˚
0.75
0.018
8˚
0.024
0.030
A2
A1
b
e
K
c
L
E
D
E1
PIN 1 IDENTIFICATION
1
0080337D
7/11
74VHC132
Tape & Reel SO-14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
8/11
TYP
0.504
22.4
0.519
0.882
Ao
6.4
6.6
0.252
0.260
Bo
9
9.2
0.354
0.362
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
74VHC132
Tape & Reel TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
330
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
TYP.
0.504
22.4
0.519
0.882
Ao
6.7
6.9
0.264
0.272
Bo
5.3
5.5
0.209
0.217
Ko
1.6
1.8
0.063
0.071
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
9/11
74VHC132
Table 10: Revision History
Date
Revision
12-Nov-2004
4
10/11
Description of Changes
Order Codes Revision - pag. 1.
74VHC132
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2004 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
11/11