74VHCT04A HEX INVERTER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 4.7 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 2 µA (MAX.) at TA=25°C COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN.), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 04 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (MAX.) DESCRIPTION The 74VHCT04A is an advanced high-speed CMOS HEX INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provides high noise immunity and stable output. SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74VHCT04AMTR 74VHCT04ATTR Power down protection is provided on all inputs and outputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V since all inputs are equipped with TTL threshold. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols December 2004 Rev. 4 1/11 74VHCT04A Figure 2: Input Equivalent Circuit Table 2: Pin Description PIN N° SYMBOL 1, 3, 5, 9, 11, 13 2, 4, 6, 8, 10, 12 7 14 NAME AND FUNCTION 1A to 6A Data Inputs 1Y to 6Y Data Outputs GND VCC Ground (0V) Positive Supply Voltage Table 3: Truth Table A Y L H H L Table 4: Absolute Maximum Ratings Symbol Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (see note 1) -0.5 to +7.0 V VO DC Output Voltage (see note 2) -0.5 to VCC + 0.5 - 20 V mA ± 20 mA VCC Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Current ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) ± 25 mA ± 50 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) VCC = 0V 2) High or Low State Table 5: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage Unit 4.5 to 5.5 V VI Input Voltage 0 to 5.5 V VO Output Voltage (see note 1) 0 to 5.5 V VO Output Voltage (see note 2) Top Operating Temperature dt/dv Input Rise and Fall Time (see note 3) (VCC = 5.0 ± 0.5V) 1) VCC = 0V 2) High or Low State 3) VIN from 0.8V to 2V 2/11 Value 0 to VCC V -55 to 125 °C 0 to 20 ns/V 74VHCT04A Table 6: DC Specifications Test Condition Symbol VIH VIL VOH VOL II ICC +ICC IOPD Parameter TA = 25°C VCC (V) High Level Input Voltage Low Level Input Voltage High Level Output Voltage 4.5 to 5.5 4.5 to 5.5 Value Min. Typ. Max. 2 -40 to 85°C -55 to 125°C Min. Min. Max. 2 0.8 Max. 2 0.8 Unit V 0.8 V 4.5 IO=-50 µA 4.4 4.5 IO=-8 mA 3.94 Low Level Output Voltage 4.5 IO=50 µA 0.1 0.1 0.1 4.5 IO=8 mA 0.36 0.44 0.55 Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current 0 to 5.5 VI = 5.5V or GND ± 0.1 ± 1.0 ± 1.0 µA 5.5 VI = VCC or GND 2 20 20 µA 5.5 One Input at 3.4V, other input at VCC or GND 1.35 1.5 1.5 mA 0 VOUT = 5.5V 0.5 5.0 5.0 µA Output Leakage Current 4.5 0.0 4.4 4.4 3.8 3.7 V V Table 7: AC Electrical Characteristics (Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time VCC (*) CL (V) (pF) 5.0 5.0 Value TA = 25°C Min. 15 50 -40 to 85°C -55 to 125°C Typ. Max. Min. Max. Min. Max. 4.7 5.5 6.7 7.7 1.0 1.0 7.5 8.5 1.0 1.0 7.5 8.5 Unit ns (*) Voltage range is 5.0V ± 0.5V Table 8: Capacitive Characteristics Test Condition Symbol Value TA = 25°C Parameter Min. Typ. Max. 10 CIN Input Capacitance 4 CPD Power Dissipation Capacitance (note 1) 14 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate) 3/11 74VHCT04A Table 9: Dynamic Switching Characteristics Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) TA = 25°C VCC (V) Min. 5.0 5.0 Value -0.8 CL = 50 pF 5.0 Typ. Max. 0.3 0.8 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. -0.3 V 2.0 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.0V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.0V. Inputs under test switching: 3.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. Figure 3: Test Circuit CL =15/50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) 4/11 74VHCT04A Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) 5/11 74VHCT04A SO-14 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 0.004 0016019D 6/11 74VHCT04A TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/11 74VHCT04A Tape & Reel SO-14 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 8/11 TYP 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74VHCT04A Tape & Reel TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/11 74VHCT04A Table 10: Revision History Date Revision 16-Dec-2004 4 10/11 Description of Changes Order Codes Revision - pag. 1. 74VHCT04A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11