LINER LT1677CN8

LT1677
Low Noise, Rail-to-Rail
Precision Op Amp
U
FEATURES
DESCRIPTIO
■
The LT ®1677 features the lowest noise performance available for a rail-to-rail operational amplifier: 3.2nV/√Hz
wideband noise, 1/f corner frequency of 13Hz and 90nV
peak-to-peak 0.1Hz to 10Hz noise. Low noise is combined
with outstanding precision: 20µV offset voltage and
0.2µV/°C drift, 130dB common mode and power supply
rejection and 7.2MHz gain bandwidth product. The common mode range exceeds the power supply by 100mV.
■
■
■
■
■
■
■
■
■
■
■
Rail-to-Rail Input and Output
100% Tested Low Voltage Noise:
3.2nV/√Hz Typ at 1kHz
4.5nV/√Hz Max at 1kHz
Offset Voltage: 60µV Max
Low VOS Drift: 0.2µV/°C Typ
Low Input Bias Current: 20nA Max
Wide Supply Range: 3V to ±18V
High AVOL: 7V/µV Min, RL = 10k
High CMRR: 109dB Min
High PSRR: 108dB Min
Gain Bandwidth Product: 7.2MHz
Slew Rate: 2.5V/µs
Operating Temperature Range: – 40°C to 85°C
The voltage gain of the LT1677 is extremely high, 19 million
(typical) driving a 10k load.
In the design, processing and testing of the device, particular
attention has been paid to the optimization of the entire
distribution of several key parameters. Consequently, the
specifications have been spectacularly improved compared
to competing rail-to-rail amplifiers.
U
APPLICATIO S
■
■
■
■
■
■
■
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
Low Noise Signal Processing
Microvolt Accuracy Threshold Detection
Strain Gauge Amplifiers
Tape Head Preamplifiers
Direct Coupled Audio Gain Stages
Infrared Detectors
Battery-Powered Microphones
U
TYPICAL APPLICATIO
Distribution of Offset Voltage
25
3V Electret Microphone Amplifier
TA = 25°C
VS = ±15V
PANASONIC
ELECTRET
CONDENSER
MICROPHONE
WM-61
www.panasonic.com/pic
(714) 373-7334
R1
10k
R3
1M
AV = –100
C1
0.68µF R2
10k
23Hz
HIGHPASS
1.5V
2
3
–
+
7
LT1677
6
TO PA
OR
HEADPHONES
4
–1.5V
PERCENT OF UNITS
20
1.5V
15
10
5
1677 TA01
0
–40 –30 –20 –10 0
10 20 30
INPUT OFFSET VOLTAGE (µV)
40
1677 TA02
1677fa
1
LT1677
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
Supply Voltage ...................................................... ±22V
Input Voltages (Note 2) ............ 0.3V Beyond Either Rail
Differential Input Current (Note 2) ..................... ± 25mA
Output Short-Circuit Duration (Note 3) ............ Indefinite
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec.)................. 300°C
Operating Temperature Range
LT1677C (Note 4) ............................. – 40°C to 85°C
LT1677I ............................................. – 40°C to 85°C
Specified Temperature Range
LT1677C (Note 5) ............................. – 40°C to 85°C
LT1677I ............................................. – 40°C to 85°C
TOP VIEW
VOS
1
TRIM
–IN 2
–
VOS
TRIM
7 +VS
+IN 3
+
6 OUT
8
5 NC
–VS 4
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 150°C/ W (N8)
TJMAX = 150°C, θJA = 190°C/ W (S0-8)
S8 PART MARKING
1677
1677I
ORDER PART NUMBER
LT1677CS8
LT1677IS8
LT1677CN8
LT1677IN8
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 3V, VCM = VO = 1.7V; VS = 5V, VCM = VO = 2.5V unless otherwise noted.
SYMBOL
PARAMETER
VOS
Input Offset Voltage (Note 11)
∆VOS
∆Temp
∆VOS
∆Time
IB
IOS
Average Input Offset Drift (Note 10)
CONDITIONS (Note 6)
MIN
Input Offset Current (Note 11)
MAX
UNITS
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
35
55
75
90
150
210
µV
µV
µV
VCM = VS + 0.1V
VCM = VS – 0.2V, 0°C ≤ TA ≤ 70°C
VCM = VS – 0.3V, – 40°C ≤ TA ≤ 85°C
●
●
150
180
200
400
550
650
µV
µV
µV
VCM = – 0.1V
VCM = 0V, 0°C ≤ TA ≤ 70°C
VCM = 0V, – 40°C ≤ TA ≤ 85°C
●
●
1.5
1.8
2.0
5.0
6.0
6.5
mV
mV
mV
SO-8
N8
●
●
0.40
0.20
2.0
1.5
µV/°C
µV/°C
Long Term Input Voltage Stability
Input Bias Current (Note 11)
TYP
µV/Mo
0.3
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
±2
±3
±7
±20
±35
±50
nA
nA
nA
VCM = VS + 0.1V
VCM = VS – 0.2V, 0°C ≤ TA ≤ 70°C
VCM = VS – 0.3V, – 40°C ≤ TA ≤ 85°C
●
●
0.19
0.19
0.25
0.40
0.60
0.75
µA
µA
µA
VCM = – 0.1V
VCM = 0V, 0°C ≤ TA ≤ 70°C
VCM = 0V, – 40°C ≤ TA ≤ 85°C
●
●
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
4
5
8
15
20
40
nA
nA
nA
VCM = VS + 0.1V
VCM = VS – 0.2V, 0°C ≤ TA ≤ 70°C
VCM = VS – 0.3V, – 40°C ≤ TA ≤ 85°C
●
●
6
10
15
30
40
65
nA
nA
nA
VCM = – 0.1V
VCM = 0V, 0°C ≤ TA ≤ 70°C
VCM = 0V, – 40°C ≤ TA ≤ 85°C
●
●
20
25
30
100
150
160
nA
nA
nA
– 1.2
–2.0
–2.3
µA
µA
µA
– 0.41
– 0.45
– 0.47
1677fa
2
LT1677
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 3V, VCM = VO = 1.7V; VS = 5V, VCM = VO = 2.5V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS (Note 6)
en
Input Noise Voltage
0.1Hz to 10Hz (Note 7)
VCM = VS
VCM = 0V
90
180
600
nVP-P
nVP-P
nVP-P
Input Noise Voltage Density (Note 8)
fO = 10Hz
VCM = VS, fO = 10Hz
VCM = 0V, fO = 10Hz
5.2
7
25
nV/√Hz
nV/√Hz
nV/√Hz
fO = 1kHz
VCM = VS, fO = 1kHz
VCM = 0V, fO = 1kHz
3.2
5.3
17
fO = 10Hz
fO = 1kHz
1.2
0.3
in
Input Noise Current Density
VCM
Input Voltage Range
RIN
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
Input Resistance
CIN
Input Capacitance
CMRR
Common Mode Rejection Ratio (Note 11)
PSRR
AVOL
Power Supply Rejection Ratio
Large-Signal Voltage Gain
MIN
●
●
TYP
– 0.1
0
0
Common Mode
MAX
4.5
UNITS
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
pA/√Hz
VS + 0.1V
VS – 0.2V
VS – 0.3V
V
V
V
2
GΩ
4.2
pF
VS = 3V
VCM = –0.1V to 3.1V
VCM = 0V to 2.7V
●
55
53
68
67
dB
dB
VS = 5V
VCM = –0.1V to 5.1V
VCM = 0V to 4.7V
●
60
58
73
72
dB
dB
VS = 2.7V to 40V, VCM = VO = 1.7V
VS = 3.1V to 40V, VCM = VO = 1.7V
●
108
105
125
120
dB
dB
VS = 3V, RL ≥ 10k, VO = 2.5V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.6
0.4
0.4
4
3
3
V/µV
V/µV
V/µV
VS = 3V, RL ≥ 2k, VO = 2.2V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.5
0.4
0.4
1
0.9
0.8
V/µV
V/µV
V/µV
VS = 3V, RL ≥ 600Ω, VO = 2.2V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.20
0.15
0.10
0.43
0.40
0.35
V/µV
V/µV
V/µV
VS = 5V, RL ≥ 10k, VO = 4.5V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.8
0.7
0.7
5
4
4
V/µV
V/µV
V/µV
VS = 5V, RL ≥ 2k, VO = 4.2V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.40
0.35
0.25
0.9
0.8
0.6
V/µV
V/µV
V/µV
VS = 5V, RL ≥ 600Ω, VO = 4.2V to 0.7V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.35
0.30
0.20
0.67
0.60
0.45
V/µV
V/µV
V/µV
1677fa
3
LT1677
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 3V, VCM = VO = 1.7V; VS = 5V, VCM = VO = 2.5V unless
otherwise noted.
SYMBOL
PARAMETER
CONDITIONS (Note 6)
VOL
Output Voltage Swing Low (Note 11)
Above GND
ISINK = 0.1mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
VOH
ISC
SR
GBW
Output Voltage Swing High (Note 11)
Output Short-Circuit Current (Note 3)
Slew Rate (Note 13)
Gain Bandwidth Product (Note 11)
MIN
TYP
MAX
UNITS
●
●
110
125
130
170
200
230
mV
mV
mV
Above GND
ISINK = 2.5mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
170
195
205
250
320
350
mV
mV
mV
Above GND
ISINK = 10mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
370
440
465
500
600
650
mV
mV
mV
Below VS
ISOURCE = 0.1mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
75
85
93
170
200
250
mV
mV
mV
Below VS
ISOURCE = 2.5mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
170
195
205
300
350
375
mV
mV
mV
Below VS
ISOURCE = 10mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
450
510
525
700
800
850
mV
mV
mV
VS = 3V
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
15
14
13
22
20
19
mA
mA
mA
VS = 5V
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
20
18
17
29
27
25
mA
mA
mA
AV = – 1
RL ≥ 10k, 0°C ≤ TA ≤ 70°C
RL ≥ 10k, – 40°C ≤ TA ≤ 85°C
●
●
1.7
1.5
1.2
2.5
2.3
2.0
V/µs
V/µs
V/µs
fO = 100kHz
fO = 100kHz, 0°C ≤ TA ≤ 70°C
fO = 100kHz, – 40°C ≤ TA ≤ 85°C
●
●
4.5
3.8
3.7
7.2
6.2
5.8
MHz
MHz
MHz
tS
Settling Time
2V Step 0.1%, AV = +1
2V Step 0.01%, AV = +1
2.1
3.5
µs
µs
RO
Open-Loop Output Resistance
Closed-Loop Output Resistance
IOUT = 0
AV = 100, f = 10kHz
80
1
Ω
Ω
IS
Supply Current (Note 12)
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
2.60
2.75
2.80
3.4
3.7
3.8
mA
mA
mA
1677fa
4
LT1677
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = VO = 0V unless otherwise noted.
SYMBOL
PARAMETER
VOS
Input Offset Voltage
∆VOS
∆Temp
Average Input Offset Drift (Note 10)
∆VOS
∆Time
Long Term Input Voltage Stability
IB
Input Bias Current
IOS
en
CONDITIONS (Note 6)
MIN
TYP
MAX
UNITS
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
20
30
45
60
120
180
µV
µV
µV
VCM = 15.1V
VCM = 14.8V, 0°C ≤ TA ≤ 70°C
VCM = 14.7V, – 40°C ≤ TA ≤ 85°C
●
●
150
180
200
400
550
650
µV
µV
µV
VCM = – 15.1V
VCM = –15V, 0°C ≤ TA ≤ 70°C
VCM = –15V, – 40°C ≤ TA ≤ 85°C
●
●
1.5
1.8
2.0
5.0
6.0
6.5
mV
mV
mV
SO-8
N8
●
●
0.40
0.20
2.0
1.5
µV/°C
µV/°C
µV/Mo
0.3
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
±2
±3
±7
±20
±35
±50
nA
nA
nA
VCM = 15.1V
VCM = 14.8V, 0°C ≤ TA ≤ 70°C
VCM = 14.7V, – 40°C ≤ TA ≤ 85°C
●
●
0.19
0.20
0.25
0.40
0.60
0.75
µA
µA
µA
VCM = –15.1V
VCM = –15V, 0°C ≤ TA ≤ 70°C
VCM = –15V, – 40°C ≤ TA ≤ 85°C
●
●
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
3
5
8
15
20
40
nA
nA
nA
VCM = 15.1V
VCM = 14.8V, 0°C ≤ TA ≤ 70°C
VCM = 14.7V, – 40°C ≤ TA ≤ 85°C
●
●
5
8
12
25
35
60
nA
nA
nA
VCM = –15.1V
VCM = –15V, 0°C ≤ TA ≤ 70°C
VCM = –15V, – 40°C ≤ TA ≤ 85°C
●
●
20
25
30
105
160
170
nA
nA
nA
– 1.2
–2.0
–2.3
Input Offset Current
µA
µA
µA
– 0.42
– 0.46
– 0.48
Input Noise Voltage
0.1Hz to 10Hz (Note 7)
VCM = 15V
VCM = –15V
90
180
600
nVP-P
nVP-P
nVP-P
Input Noise Voltage Density
fO = 10Hz
VCM = 15V, fO = 10Hz
VCM = –15V, fO = 10Hz
5.2
7
25
nV/√Hz
nV/√Hz
nV/√Hz
fO = 1kHz
VCM = 15V, fO = 1kHz
VCM = –15V, fO = 1kHz
3.2
5.3
17
fO = 10Hz
fO = 1kHz
1.2
0.3
in
Input Noise Current Density
VCM
Input Voltage Range
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
RIN
Input Resistance
CIN
Input Capacitance
Common Mode
●
●
– 15.1
– 15.0
– 15.0
4.5
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
pA/√Hz
15.1
14.8
14.7
V
V
V
2
GΩ
4.2
pF
1677fa
5
LT1677
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = VO = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS (Note 6)
MIN
TYP
CMRR
Common Mode Rejection Ratio
VCM = –13.3V to 14V
●
109
105
130
124
dB
dB
●
74
72
95
91
dB
dB
●
106
103
130
125
dB
dB
VS = 2.7V to 40V
VS = 3.1V to 40V
●
108
105
125
120
dB
dB
RL ≥ 10k, VO = ±14V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
7
4
3
19
13
8
V/µV
V/µV
V/µV
RL ≥ 2k, VO = ±13.5V
0°C ≤ TA ≤ 70°C
–40°C ≤ TA ≤ 85°C
●
●
0.50
0.30
0.15
0.75
0.67
0.24
V/µV
V/µV
V/µV
0.2
0.5
V/µV
VCM = –15.1V to 15.1V
VCM = –15V to 14.7V
PSRR
AVOL
Power Supply Rejection Ratio
Large-Signal Voltage Gain
VS = ±1.7V to ±18V
RL ≥ 600Ω, VO = ±10V
VOL
VOH
ISC
SR
GBW
Output Voltage Swing Low
Output Voltage Swing High
Gain Bandwidth Product
UNITS
Above – VS
ISINK = 0.1mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
110
125
130
170
200
230
mV
mV
mV
Above – VS
ISINK = 2.5mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
170
195
205
250
320
350
mV
mV
mV
Above – VS
ISINK = 10mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
370
440
450
500
600
650
mV
mV
mV
Below +VS
ISOURCE = 0.1mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
110
130
140
170
200
250
mV
mV
mV
Below +VS
ISOURCE = 2.5mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
210
240
250
300
350
375
mV
mV
mV
Below +VS
ISOURCE = 10mA
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
520
590
620
700
800
850
mV
mV
mV
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
●
●
25
20
18
35
30
28
mA
mA
mA
RL ≥ 10k (Note 9)
RL ≥ 10k (Note 9) 0°C ≤ TA ≤ 70°C
RL ≥ 10k (Note 9) – 40°C ≤ TA ≤ 85°C
●
●
1.7
1.5
1.2
2.5
2.3
2.0
V/µs
V/µs
V/µs
fO = 100kHz
fO = 100kHz, 0°C ≤ TA ≤ 70°C
fO = 100kHz, – 40°C ≤ TA ≤ 85°C
●
●
4.5
3.8
3.7
7.2
6.2
5.8
MHz
MHz
MHz
Output Short-Circuit Current (Note 3)
Slew Rate
MAX
1677fa
6
LT1677
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = VO = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS (Note 6)
THD
Total Harmonic Distortion
RL = 2k, AV = 1, fO = 1kHz, VO = 10VP-P
MIN
tS
Settling Time
RO
Open-Loop Output Resistance
Closed-Loop Output Resistance
IS
Supply Current
TYP
MAX
UNITS
0.0006
%
10V Step 0.1%, AV = +1
10V Step 0.01%, AV = +1
5
6
µs
µs
IOUT = 0
AV = 100, f = 10kHz
80
1
Ω
Ω
0°C ≤ TA ≤ 70°C
– 40°C ≤ TA ≤ 85°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The inputs are protected by back-to-back diodes. Current limiting
resistors are not used in order to achieve low noise. If differential input
voltage exceeds ±1.4V, the input current should be limited to 25mA. If the
common mode range exceeds either rail, the input current should be
limited to 10mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum.
Note 4: The LT1677C and LT1677I are guaranteed functional over the
Operating Temperature Range of – 40°C to 85°C.
Note 5: The LT1677C is guaranteed to meet specified performance from
0°C to 70°C. The LT1677C is designed, characterized and expected to
meet specified performance from – 40°C to 85°C but is not tested or QA
sampled at these temperatures. The LT1677I is guaranteed to meet
specified performance from – 40°C to 85°C.
2.75
3.00
3.10
●
●
3.5
3.9
4.0
mA
mA
mA
Note 6: Typical parameters are defined as the 60% yield of parameter
distributions of individual amplifier; i.e., out of 100 LT1677s, typically 60
op amps will be better than the indicated specification.
Note 7: See the test circuit and frequency response curve for 0.1Hz to
10Hz tester in the Applications Information section of the LT1677 data
sheet.
Note 8: Noise is 100% tested at ±15V supplies.
Note 9: Slew rate is measured in AV = – 1; input signal is ±7.5V, output
measured at ±2.5V.
Note 10: This parameter is not 100% tested. VS = 3V and 5V limits are
guaranteed by correlation to VS = ±15V test.
Note 11: VS = 5V limits are guaranteed by correlation to VS = 3V and
VS = ±15V tests.
Note 12: VS = 3V limits are guaranteed by correlation to VS = 5V and
VS = ±15V tests.
Note 13: Guaranteed by correlation to slew rate at VS = ±15V and GBW at
VS = 3V and VS = ±15V tests.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Voltage Noise vs Frequency
0.1Hz to 10Hz Voltage Noise
0.01Hz to 1Hz Voltage Noise
VCM < –14.5V
1/f CORNER 8.5Hz
10
VCM
–13.5V TO 14.5V
VOLTAGE NOISE (20nV/DIV)
1/f CORNER 10Hz
VOLTAGE NOISE (20nV/DIV)
RMS VOLTAGE NOISE DENSITY (nV/√Hz)
100
VCM > 14.5V
1/f CORNER 13Hz
VS = ±15V
TA = 25°C
1
0.1
1
10
100
FREQUENCY (Hz)
1000
1677 G01
0
2
4
6
TIME (SECONDS)
8
10
1677 G03
0
20
40
60
TIME (SECONDS)
80
100
1677 G04
1677fa
7
LT1677
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Voltage Noise vs Temperature
6
10Hz
5
4
1kHz
3
10
VS = ±15V
9 VCM = 0V
VS = ±15V
TA = 25°C
VCM < –13.5V
1/f CORNER 180Hz
1
VCM
–13.5V TO 14.5V
1/f CORNER 90Hz
1/f CORNER 60Hz
50
25
0
75
TEMPERATURE (°C)
100
100
1000
FREQUENCY (Hz)
10
125
600
VCM = 14.7V
CURRENT INTO DUT
200
VS = ±15V
TA = 25°C
50
25
0
75
TEMPERATURE (°C)
100
125
400
VCM = –13.6V
200
VCM = 15.15V
INPUT BIAS CURRENT
0
VCM = 14.3V
–200
VCM = –15.3V
–400
200
16
40
6
N PACKAGE
1.0
100
0.5
50
0
0
–0.5
–50
–1.0
–100
–1.5
–150
VS = ±1.5V TO ±15V
TA = 25°C
–200
5 TYPICAL PARTS
–250
2.0 –0.8 –0.4 V + 0.4
–2.5
–1.0
V–
1.0
VCM – V – (V)
VCM – V + (V)
1677 G10
Distribution of Input Offset
Voltage Drift (SO-8)
30
VS = ±15V
TA = –40°C TO 85°C
167 PARTS (4 LOTS)
35
30
25
20
15
10
2
150
VOS IS REFERRED
TO VCM = 0V
25
PERCENT OF UNITS (%)
45
PERCENT OF UNITS (%)
CHANGE IN OFFSET VOLTAGE (µV)
50
8
4
250
Distribution of Input Offset
Voltage Drift (N8)
VS = ±15V
TA = 25°C
125
100
2.5
1677 G09
Warm-Up Drift
SO PACKAGE
50
25
0
75
TEMPERATURE (°C)
2.0
–2.0
–800
0
4
–16 –12 –8 –4
8
12
COMMON MODE INPUT VOLTAGE (V)
1677 G06
10
2
1.5
–600
100
–50 –25
3
Offset Voltage Shift
vs Common Mode
OFFSET VOLTAGE (mV)
INPUT BIAS CURRENT (nA)
300
4
OFFSET VOLTAGE (µV)
INPUT BIAS CURRENT (nA)
800
VS = ±15V
400
5
1677 G05
Input Bias Current Over the
Common Mode Range
VCM = –14V
CURRENT OUT OF DUT
6
1677 G07
Input Bias Current
vs Temperature
500
7
0
–50 –25
10000
1677 G08
600
8
1
VCM > 14.5V
0.1
2
–50 –25
INPUT BIAS CURRENT (nA)
10
VS = ±15V
VCM = 0V
RMS CURRENT NOISE DENSITY (pA/√Hz)
RMS VOLTAGE NOISE DENSITY (nV/√Hz)
7
Input Bias Current
vs Temperature
Current Noise vs Frequency
VS = ±15V
TA = –40°C TO 85°C
201 PARTS (5 LOTS)
20
15
10
5
5
0
0
1
3
2
TIME (MINUTES)
4
5
1677 G02
0
–1.0
–0.6 –0.2 0.2
0.6
1.0
1.4
INPUT OFFSET VOLTAGE DRIFT (µV/°C)
1677 G13
0
–0.8 –0.4 0
0.4 0.8 1.2 1.6 2.0
INPUT OFFSET VOLTAGE DRIFT (µV/°C)
1677 G37
1677fa
8
LT1677
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Common Mode Range
vs Temperature
VOS vs Temperature of
Representative Units
OFFSET VOLTAGE (mV)
80
5
2.0
200
4
1.5
150
60
40
20
0
–20
VS = ±2.5V TO ±15V
125°C
1.0
0.5
100
25°C
–55°C
0
0
–0.5
–50
VOS IS REFERRED 125°C
TO VCM = 0V
–1.0
–100
25°C
3
2
1
0
–1
–2
–3
–40
–1.5
–150
–60
–2.0
–200
–4
–80
–55 –35 –15
–2.5
–1.0
–250
–5
V–
2.0 –0.8 –0.4
1.0
VCM – VS– (V)
V+
160
COMMON MODE REJECTION RATIO (dB)
TA = –55°C
2
1
±5
±10
±15
SUPPLY VOLTAGE (V)
0
VS = ±15V
TA = 25°C
VCM = 0V
140
120
100
80
60
40
20
10k
100k
1M
FREQUENCY (Hz)
60
VCM = 0V
VCM = VCC
20
–20
0.01
10k
100
FREQUENCY (Hz)
1M
NEGATIVE SUPPLY
80
POSITIVE SUPPLY
60
40
20
10M
100
100M
1677 G18
1
10
100
10k
1k
FREQUENCY (Hz)
100k
1677 G17
60
TA = 25°C
RL TO GND
VCM: VO = VS/2
50
RL = 10k
10
RL = 2k
1
VS = ±15V
TA = 25°C
RL = 10k TO 2k
40
RISING
EDGE
30
20
FALLING
EDGE
10
0
10
20
SUPPLY VOLTAGE (V)
1M
Overshoot vs Load Capacitance
0.1
1
100
1677 G16
OPEN LOOP VOLTAGE GAIN (V/µV)
140
VCM = VEE
120
Voltage Gain vs Supply Voltage
(Single Supply)
VS = ±15V
TA = 25°C
VS = ±15V
TA = 25°C
140
0
1k
Voltage Gain vs Frequency
100
160
0
±20
1677 G15
180
Power Supply Rejection Ratio
vs Frequency
OVERSHOOT (%)
SUPPLY CURRENT (mA)
TA = 25°C
1677 G14
Common Mode Rejection Ratio
vs Frequency
4
TA = 125°C
0 100 200 300 400 500 600 700 800 900
TIME (HOURS)
1677 G12
Supply Current vs Supply Voltage
3
0.4
VCM – VS+ (V)
POWER SUPPLY REJECTION RATIO (dB)
5 25 45 65 85 105 125
TEMPERATURE (°C)
1677 G11
VOLTAGE GAIN (dB)
50
–55°C
OFFSET VOLTAGE (µV)
VOLTAGE OFFSET (µV)
100
250
2.5
VS = ±15V
VCM = 0V
SO-8
N8
120
OFFSET VOLTAGE CHANGE (µV)
140
Long-Term Stability of Four
Representative Units
30
1677 G19
0
10
100
CAPACITANCE (pF)
1000
1677 G21
1677fa
9
LT1677
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Large-Signal Transient Response
GAIN BANDWIDTH PRODUCT, fO = 100kHz (MHz)
PHASE MARGIN (DEG)
PM, GBWP, SR vs Temperature
70
VS = ±15V
CL = 15pF
PHASE
60
8
GBW
7
50
6
5
SLEW RATE (V/µs)
3
4
SLEW
2
1
–50 –25
50
25
0
75
TEMPERATURE (°C)
Small-Signal Transient Response
50mV
10V
0
– 10V
– 50mV
AVCL = – 1
VS = ±15V
5µs/DIV
AVCL = 1
VS = ±15V
CL = 15pF
0.5µs/DIV
125
100
1677 G22
Settling Time vs Output Step
(Noninverting)
0.1% OF
FULL SCALE
0.01% OF
FULL SCALE
0.1% OF
FULL SCALE
4
2
10
VOUT
+
8
6
VIN
8
6
–
2k
VIN
RL = 1k
6
0.01% OF
FULL SCALE
4
PHASE
10
20
0
0
–10
0.1
1
10
FREQUENCY (MHz)
–20
100
1677 G35
50
20
0
0
0.1
10
–20
100
1
10
FREQUENCY (MHz)
1677 G34
Output Voltage Swing
vs Load Current
100
VS = ±15V
VCM = –14V
CL = 10pF
80
125°C
25°C
– 55°C 60
40
VOLTAGE GAIN (dB)
VOLTAGE GAIN (dB)
GAIN
8
30
20
40
GAIN
PHASE
10
20
0
0
–10
0.1
1
10
FREQUENCY (MHz)
PHASE SHIFT (DEG)
40
PHASE SHIFT (DEG)
20
PHASE
10
Gain, Phase Shift vs Frequency
100
VS = ±15V
VCM = 14.7V
CL = 10pF
80
125°C
25°C
– 55°C 60
30
40
GAIN
1677 G26
Gain, Phase Shift vs Frequency
40
20
–10
6
1677 G25
50
30
0.1% OF
FULL SCALE
0
–10 –8 –6 –4 –2 0 2 4
OUTPUT STEP (V)
10
40
VOUT
+
8
0.01% OF
FULL SCALE
100
VS = ±15V
VCM = 0V
CL = 10pF
80
125°C
25°C
– 55°C 60
2k
0.1% OF
2 FULL SCALE
VS = ±15V
AV = –1
TA = 25°C
0
–10 –8 –6 –4 –2 0 2 4
OUTPUT STEP (V)
50
VS = ±15V
AV = 1
TA = 25°C
5k
–
PHASE SHIFT (DEG)
SETTLING TIME (µs)
10
12
5k
–20
100
1677 G36
+VS – 0
VS = ±15V
–0.1
–0.2
–0.3
–0.4
–0.5
–0.6
–0.7
0.5
125°C
0.4
25°C
0.3
OUTPUT VOLTAGE SWING (V)
0.01% OF
FULL SCALE
SETTLING TIME (µs)
12
Gain, Phase Shift vs Frequency
VOLTAGE GAIN (dB)
Settling Time vs Output Step
(Inverting)
–55°C
25°C
125°C
0.2
–55°C
0.1
–VS + 0
–10 –8 –6 –4 –2 0 2 4 6 8
ISOURCE
ISINK
OUTPUT CURRENT (mA)
10
1677 G27
1677fa
10
LT1677
U W
TYPICAL PERFOR A CE CHARACTERISTICS
SHORT-CIRCUIT CURRENT (mA)
SINKING
SOURCING
1
AV = +100
0.1
AV = +1
0.01
100
10
10k
1k
FREQUENCY (Hz)
–55°C
30
25°C
20
125°C
10
–30
–35
125°C
–40
–55°C
–45
1M
0
AV = –100
0.001
AV = –10
AV = –1
0.0001
20
100
1k
FREQUENCY (Hz)
10k 20k
1677 G31
0.01
AV = 100
0.001
AV = 10
AV = 1
3
2
4
1
TIME FROM OUTPUT SHORT TO GND (MIN)
20
100
1k
FREQUENCY (Hz)
10k 20k
1677 G30
Total Harmonic Distortion and
Noise vs Output Amplitude for
Noninverting Gain
TOTAL HARMONIC DISTORTION + NOISE (%)
TOTAL HARMONIC DISTROTION + NOISE (%)
ZL = 2k/15pF
VS = ±15V
VO = 10VP-P
AV = –1, –10, – 100
MEASUREMENT BANDWIDTH
= 10Hz TO 80kHz
ZL = 2k/15pF
VS = ±15V
VO = 10VP-P
AV = +1, +10, +100
MEASUREMENT BANDWIDTH
= 10Hz TO 80kHz
1677 G28
Total Harmonic Distortion and
Noise vs Frequency for Inverting
Gain
0.1
0.1
0.0001
–50
100k
1677 G29
0.01
25°C
1
Total Harmonic Distortion and
Noise vs Output Amplitude for
Inverting Gain
ZL = 2k/15pF
VS = ±15V
fO = 1kHz
AV = +1, +10, +100
MEASUREMENT BANDWIDTH
= 10Hz TO 22kHz
AV = 100
0.1
0.01
AV = 10
AV = 1
0.001
0.0001
0.3
1
10
OUTPUT SWING (VP-P)
30
1677 G32
TOTAL HARMONIC DISTORTION + NOISE (%)
OUTPUT IMPEDANCE (Ω)
10
VS = ±15V
40
TOTAL HARMONIC DISTROTION + NOISE (%)
50
100
0.001
Total Harmonic Distortion and
Noise vs Frequency for
Noninverting Gain
Output Short-Circuit Current
vs Time
Closed-Loop Output Impedance
vs Frequency
1
ZL = 2k/15pF
VS = ±15V
fO = 1kHz
AV = –1, –10, –100
MEASUREMENT BANDWIDTH
= 10Hz TO 22kHz
0.1
AV = –100
0.01
AV = –10
AV = –1
0.001
0.0001
0.3
1
10
OUTPUT SWING (VP-P)
30
1677 G33
1677fa
11
LT1677
U
W
U U
APPLICATIO S I FOR ATIO
General
The LT1677 series devices may be inserted directly into
OP-07, OP-27, OP-37 and sockets with or without removal
of external compensation or nulling components. In addition, the LT1677 may be fitted to 741 sockets with the
removal or modification of external nulling components.
The adjustment range with a 10kΩ pot is approximately
±2.5mV. If less adjustment range is needed, the sensitivity and resolution of the nulling can be improved by using
a smaller pot in conjunction with fixed resistors. The
example has an approximate null range of ±200µV
(Figure 3).
Rail-to-Rail Operation
10k
15V
To take full advantage of an input range that can exceed
the supply, the LT1677 is designed to eliminate phase
reversal. Referring to the photographs shown in Figure 1,
the LT1677 is operating in the follower mode (AV = +1) at
a single 3V supply. The output of the LT1677 clips cleanly
and recovers with no phase reversal. This has the benefit
of preventing lock-up in servo systems and minimizing
distortion components.
2
–
1
8
7
LT1677
INPUT
3
6
OUTPUT
+
4
–15V
1677 F02
Figure 2. Standard Adjustment
1k
Offset Voltage Adjustment
15V
4.7k
The input offset voltage of the LT1677 and its drift with
temperature are permanently trimmed at wafer
testing to a low level. However, if further adjustment of
VOS is necessary, the use of a 10kΩ nulling potentiometer
will not degrade drift with temperature. Trimming to a
value other than zero creates a drift of (VOS / 300)µV/°C,
e.g., if VOS is adjusted to 300µV, the change in drift will be
1µV/°C (Figure 2).
Figure 3. Improved Sensitivity Adjustment
Input = – 0.5V to 3.5V
LT1677 Output
4.7k
2
3
+
8
LT1677
7 6
OUTPUT
4
–15V
3V
3V
2V
2V
1V
1V
0V
0V
– 0.5V
– 0.5V
1577 F01a
–
1
1677 F03
1577 F01b
Figure 1. Voltage Follower with Input Exceeding the Supply Voltage (VS = 3V)
1677fa
12
LT1677
U
W
U U
APPLICATIO S I FOR ATIO
Offset Voltage and Drift
Thermocouple effects, caused by temperature gradients
across dissimilar metals at the contacts to the input
terminals, can exceed the inherent drift of the amplifier
unless proper care is exercised. Air currents should be
minimized, package leads should be short, the two input
leads should be close together and maintained at the same
temperature.
The circuit shown to measure offset voltage is also used as
the burn-in configuration for the LT1677, with the supply
voltages increased to ±20V (Figure 4).
50k*
15V
2
100Ω*
3
–
7
LT1677
+
4
50k*
–15V
6
As with all operational amplifiers when RF > 2k, a pole will
be created with RF and the amplifier’s input capacitance,
creating additional phase shift and reducing the phase
margin. A small capacitor (20pF to 50pF) in parallel with RF
will eliminate this problem.
Noise Testing
The 0.1Hz to 10Hz peak-to-peak noise of the LT1677 is
measured in the test circuit shown (Figure 6a). The frequency response of this noise tester (Figure 6b) indicates
that the 0.1Hz corner is defined by only one zero. The test
time to measure 0.1Hz to 10Hz noise should not exceed
ten seconds, as this time limit acts as an additional zero to
eliminate noise contributions from the frequency band
below 0.1Hz.
Measuring the typical 90nV peak-to-peak noise performance of the LT1677 requires special test precautions:
VOUT
VOUT = 1000VOS
1. The device should be warmed up for at least five
minutes. As the op amp warms up, its offset voltage
changes typically 3µV due to its chip temperature
increasing 10°C to 20°C from the moment the power
supplies are turned on. In the ten-second measurement
interval these temperature-induced effects can easily
exceed tens of nanovolts.
*RESISTORS MUST HAVE LOW
THERMOELECTRIC POTENTIAL
1677 F04
Figure 4. Test Circuit for Offset Voltage and
Offset Voltage Drift with Temperature
Unity-Gain Buffer Application
When RF ≤ 100Ω and the input is driven with a fast, largesignal pulse (>1V), the output waveform will look as
shown in the pulsed operation diagram (Figure 5).
During the fast feedthrough-like portion of the output, the
input protection diodes effectively short the output to the
input and a current, limited only by the output short-circuit
protection, will be drawn by the signal generator. With
RF ≥ 500Ω, the output is capable of handling the current
requirements (IL ≤ 20mA at 10V) and the amplifier stays
in its active mode and a smooth transition will occur.
RF
–
2. For similar reasons, the device must be well shielded
from air currents to eliminate the possibility of
thermoelectric effects in excess of a few nanovolts,
which would invalidate the measurements.
3. Sudden motion in the vicinity of the device can also
“feedthrough” to increase the observed noise.
Current noise is measured in the circuit shown in Figure 7
and calculated by the following formula:
1/ 2
2⎤
⎡
2
⎢ eno − 130nV • 101 ⎥
⎦
in = ⎣
1MΩ 101
)
( ) (
( )( )
2.5V/µs
OUTPUT
+
LT1677
1677 F05
Figure 5. Pulsed Operation
The LT1677 achieves its low noise, in part, by operating
the input stage at 100µA versus the typical 10µA of most
other op amps. Voltage noise is inversely proportional
while current noise is directly proportional to the square
1677fa
13
LT1677
U
W
U U
APPLICATIO S I FOR ATIO
100
0.1µF
90
100k
–
2k
*
LT1677
+
+
4.3k
–
2.2µF
VOLTAGE GAIN
= 50,000
24.3k
500k
+
0.1
1
10
FREQUENCY (Hz)
100
Figure 6b. 0.1Hz to 10Hz Peak-to-Peak
Noise Tester Frequency Response
root of the input stage current. Therefore, the LT1677’s
current noise will be relatively high. At low frequencies, the
low 1/f current noise corner frequency (≈ 90Hz) minimizes current noise to some extent.
LT1677
eno
Figure 7
In most practical applications, however, current noise will
not limit system performance. This is illustrated in the
Total Noise vs Source Resistance plot (Figure 8) where:
Total Noise = [(op amp voltage noise)2 + (resistor noise)2
+ (current noise RS)2]1/2
Three regions can be identified as a function of source
resistance:
1000
VS = ±15V
TA = 25°C
R
TOTAL NOISE DENSITY (nV/√Hz)
30
0.01
1677 F06b
1677 F07
R
(i) RS ≤ 400Ω. Voltage noise dominates
(ii) 400Ω ≤ RS ≤ 50k at 1kHz Resistor noise
dominates
400Ω ≤ RS ≤ 8k at 10Hz
(iii) RS > 50k at 1kHz Current noise
dominates
RS > 8k at 10Hz
SOURCE RESISTANCE = 2R
}
AT 1kHz
AT 10Hz
}
10
RESISTOR
NOISE ONLY
1
0.1
50
1677 F06a
100k
–
60
40
0.1µF
Figure 6a. 0.1Hz to 10Hz Noise Test Circuit
500k
70
110k
100k
*DEVICE UNDER TEST
NOTE: ALL CAPACITOR VALUES ARE FOR
NONPOLARIZED CAPACITORS ONLY
100
SCOPE
×1
RIN = 1M
LT1001
4.7µF
100Ω
22µF
GAIN (dB)
10Ω
80
1
10
SOURCE RESISTANCE (kΩ)
100
1677 F08
Figure 8. Total Noise vs Source Resistance
Clearly the LT1677 should not be used in region (iii), where
total system noise is at least six times higher than the
voltage noise of the op amp, i.e., the low voltage noise
specification is completely wasted. In this region the
LT1792 or LT1793 is the best choice.
1677fa
14
LT1677
U
W
U U
APPLICATIO S I FOR ATIO
Rail-to-Rail Input
Rail-to-Rail Output
The LT1677 has the lowest voltage noise, offset voltage
and highest gain when compared to any rail-to-rail op
amp. The input common mode range for the LT1677 can
exceed the supplies by at least 100mV. As the common
mode voltage approaches the positive rail (+VS – 0.7V),
the tail current for the input pair (Q1, Q2) is reduced,
which prevents the input pair from saturating (refer to the
Simplified Schematic). The voltage drop across the load
resistors RC1, RC2 is reduced to less than 200mV, degrading the slew rate, bandwidth, voltage noise, offset voltage
and input bias current (the cancellation is shut off).
The rail-to-rail output swing is achieved by using transistor collectors (Q28, Q29) instead of customary class A-B
emitter followers for the output stage. Referring to the
Simplified Schematic, the output NPN transistor (Q29) sinks
the current necessary to move the output in the negative
direction. The change in Q29’s base emitter voltage is reflected directly to the gain node (collectors of Q20 and Q16).
For large sinking currents, the delta VBE of Q29 can dominate the gain. Figure 9 shows the change in input voltage
for a change in output voltage for different load resistors
connected between the supplies. The gain is much higher
for output voltages above ground (Q28 sources current)
since the change in base emitter voltage of Q28 is attenuated by the gain in the PNP portion of the output stage.
Therefore, for positive output swings (output sourcing
current) there is hardly any change in input voltage for any
load resistance. Highest gain and best linearity is achieved
when the output is sourcing current, which is the case in
single supply operation when the load is ground referenced.
Figure 10 shows gains for both sinking and sourcing load
currents for a worst-case load of 600Ω.
RL = 600
RL = 1k
RL = 10k
– 15 – 10 – 5 0 5 10 15
OUTPUT VOLTAGE (V)
TA = 25°C
VS = ±15V
RL CONNECTED TO 0V
MEASURED ON TEKTRONIX 577 CURVE TRACER
Figure 9. Voltage Gain Split Supply
RL TO 5V
INPUT VOLTAGE (5µV/DIV)
INPUT VOLTAGE (50µV/DIV)
When the input common mode range goes below 1.5V
above the negative rail, the NPN input pair (Q1, Q2) shuts
off and the PNP input pair (Q8, Q9) turns on. The offset
voltage, input bias current, voltage noise and bandwidth
are also degraded. The graph of Offset Voltage Shift vs
Common Mode shows where the knees occur by displaying the change in offset voltage. The change-over points
are temperature dependent, see the graph Common Mode
Range vs Temperature.
RL TO 0V
0
1
2
3
4
OUTPUT VOLTAGE (V)
TA = 25°C
VS = 5V
RL = 600Ω
MEASURED ON TEKTRONIX 577 CURVE TRACER
5
Figure 10. Voltage Gain Single Supply
1677fa
15
LT1677
U
TYPICAL APPLICATIO S
Microvolt Comparator with Hysteresis
3V Strain Gauge Amplifier
3V
3V
10M
5%
3
+
7
1
INPUT
2
–
15k
1%
LT1677
6
R11
1k
15k
1%
R9
3.4Ω
R8
7.5Ω
R*
R*
R*
R*
R7
22.1Ω
R2
5Ω
OUTPUT
R10
232Ω
4
R3
5.49k
R5
698Ω
3V
+
1677 TA03
–
POSITIVE FEEDBACK TO ONE OF THE NULLING TERMINALS
CREATES APPROXIMATELY 5µV OF HYSTERESIS. OUTPUT
CAN SINK 16mA
INPUT OFFSET VOLTAGE IS TYPICALLY CHANGED LESS THAN
5µV DUE TO THE FEEDBACK
VOUT
LT1677
R*
R4
5.49k
R2
5Ω
*OMEGA SG-3/350LY11
350Ω, 1%
ALL OTHER RESISTORS 1%
(
)(
FOR TEMP
COMPENSATION
R* OF GAIN
R6
22.1Ω
)
1677 TA06
R4
≅ 1000
AV = 2 • R* + R6
R2 + (R*/2)
R6
TRIM R11 FOR BRIDGE BALANCE
Precision High Side Current Sense
SOURCE
3V < VS < 36V
RIN
1k
RLINE
0.1Ω
2
3
–
+
7
LT1677
4
LOAD
6
ZETEX
BC856B
VOUT
ROUT
ROUT
VOUT
20k
ILOAD = RLINE RIN
= 2V/AMP
1677 TA07
1677fa
16
LT1677
U
TYPICAL APPLICATIO S
3V Super Electret Microphone Amplifier with DC Servo
1.5V
1.5V
2N3906
2N3906
C1
10pF
R1
1M
16kHz
ROLL OFF
3
–
+
R3
1M
2
–
3
+
7
LT1677
R5
2k
1.5V
1.5V
2
C3
0.022µF
7Hz POLE FOR SERVO
7
LT1677
6
4
6
–1.5V
4
R2
80k
–1.5V
C4
1µF
PANASONIC
ELECTRET
CONDENSER
MICROPHONE
WM-61
(714) 373-7334
R4
8k
C2
100pF
20kHz
ROLL OFF
1.5V
2
3
–
+
7
LT1677
6
TO
HEADPHONES
4
–1.5V
–1.5V
1677 TA05
1677fa
17
Q13
×2
IA
Q21
R21
100Ω
R24
100Ω
Q24
Q8
Q9
R9
200Ω
Q1A
RC1A
6k
Q3
Q1B
Q12
100µA
IC
Q2A
Q10
PAD
8
Q2B
RC2A
6k
RC2B
1k
Q6
Q4
ID
50µA
Q11
Q7
IC = 200µA VCM < 0.7V BELOW +VS ID = 100µA VCM < 0.7V BELOW +VS
50µA VCM > 0.7V BELOW +VS
0µA VCM > 0.7V BELOW +VS
R8
200Ω
D2
D3
IB
D1
D4
IA, IB = 0µA VCM > 1.5V ABOVE –VS
200µA VCM < 1.5V ABOVE –VS
R13
100Ω
+IN
–IN
Q5
PAD
1
C10
81pF
Q17
Q15
50µA
Q18
R15
1k
Q19
R19
2k
R14
1k
Q14
Q22
100µA
200µA
R16
1k
Q16
160µA
Q20
R20
2k
+
R25
1k
Q25
Q23
C2
80pF
R2
50Ω
Q32
R30
2k
Q30
Q31
R32
1.5k
R26
100Ω
Q26
R1
500Ω
Q35
Q38
Q34
R3
100Ω
C1
40pF
+
RC1B
1k
C3
40pF
Q27
R34
2k
R54
100Ω
1677 SS
R23B
10k
R29
10Ω
Q29
Q28
–VS
C4
20pF
R23A
10k
+
+
18
+
+VS
OUT
LT1677
W
W
SI PLIFIED SCHE ATIC
1677fa
LT1677
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
.255 ± .015*
(6.477 ± 0.381)
.300 – .325
(7.620 – 8.255)
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
8.255
+0.889
–0.381
.130 ± .005
(3.302 ± 0.127)
.045 – .065
(1.143 – 1.651)
)
.120
(3.048) .020
MIN
(0.508)
MIN
.018 ± .003
.100
(2.54)
BSC
(0.457 ± 0.076)
N8 1002
NOTE:
1. DIMENSIONS ARE
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
NOTE 3
.045 ±.005
.050 BSC
8
.245
MIN
7
6
5
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
× 45°
(0.254 – 0.508)
.008 – .010
(0.203 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
.053 – .069
(1.346 – 1.752)
.014 – .019
(0.355 – 0.483)
TYP
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
2
3
4
.004 – .010
(0.101 – 0.254)
.050
(1.270)
BSC
SO8 0303
1677fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT1677
U
TYPICAL APPLICATIO
gain of ~107. Components R5 and Q1 convert the voltage
into a current for transmission back to R10, which converts it into a voltage again. The LM334 and 2N3904 are
not temperature compensated so the DC output contains
temperature information.
This 2-wire remote Geophone preamp operates on a
current-loop principle and so has good noise immunity.
Quiescent current is ≈10mA for a VOUT of 2.5V. Excitation
will cause AC currents about this point of ~±4mA for a
VOUT of ~±1V max. The op amp is configured for a voltage
2-Wire Remote Geophone Preamp
R9
20Ω
V+
R
LINEAR
TECHNOLOGY
LM334Z
6mA
R8
11Ω
V–
3V
C
LT1431CZ
R
R6
4.99k
+
R7
24.9k
A
R4
14k
C3
220µF
R1
365Ω
GEOSPACE
GS-20DX
RL = 630Ω
GEOPHONE
www.geospacecorp.com/default.htm
(713) 939-7093
R2
100k
2
–
3
+
7
–
LT1677
+
C2
0.1µF
Q1
2N3904
12V
R5
243Ω
R10
250Ω
6
VOUT
2.5V ±1V
4
R3
16.2k
C4
1000pF
1677 TA04
AV =
R2 + R3||R4
R1 + RL
≅ 107
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1028/LT1128
Ultralow Noise Precision Op Amps
Lowest Noise 0.85nV/√Hz
LT1115
Ultralow Noise, Low distortion Audio Op Amp
0.002% THD, Max Noise 1.2nV/√Hz
LT1124/LT1125
Dual/Quad Low Noise, High Speed Precision Op Amps
Similar to LT1007
LT1126/LT1127
Dual/Quad Decompensated Low Noise, High Speed Precision Op Amps
Similar to LT1037
LT1226
Low Noise, Very High Speed Op Amp
1GHz, 2.6nV/√Hz, Gain of 25 Stable
LT1498/LT1499
10MHz, 5V/µs, Dual/Quad Rail-to-Rail Input and Output Op Amps
Precision C-LoadTM Stable
LT1792
Low Noise, Precision JFET Input Op Amp
4.2nV/√Hz, 10fA/√Hz
LT1793
Low Noise, Picoampere Bias Current Op Amp
6nV/√Hz, 1fA/√Hz, IB = 10pA Max
LT1806
Low Noise, 325MHz Rail-to-Rail Input and Output Op Amp
3.5nV/√Hz
LT1881/LT1882
Dual/Quad Rail-to-Rail Output Picoamp Input Precision Op Amps
CLOAD to 1000pF, IB = 200pA Max
LT1884/LT1885
Dual/Quad Rail-to-Rail Output Picoamp Input Precision Op Amps
2.2MHz Bandwidth, 1.2V/µs SR
C-Load is a trademark of Linear Technology Corporation.
1677fa
20
Linear Technology Corporation
LT 0306 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
© LINEAR TECHNOLOGY CORPORATION 2000