CY7C1340G 4-Mbit (128K x 32) Pipelined DCD Sync SRAM Functional Description[1] Features • Registered inputs and outputs for pipelined operation • Optimal for performance (Double-Cycle deselect) — Depth expansion without wait state • 128K × 32 common I/O architecture • 3.3V core power supply (VDD) • 3.3V / 2.5V I/O power supply (VDDQ) • Fast clock-to-output times — 2.6 ns (for 250-MHz device) • Provide high-performance 3-1-1-1 access rate • User-selectable burst counter supporting Intel® Pentium® interleaved or linear burst sequences • Separate processor and controller address strobes • Synchronous self-timed writes • Asynchronous Output Enable • Available in lead-free 100-Pin TQFP package • “ZZ” Sleep Mode option The CY7C1340G SRAM integrates 128K x 32 SRAM cells with advanced synchronous peripheral circuitry and a two-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered Clock Input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining Chip Enable (CE1), depth-expansion Chip Enables (CE2 and CE3), Burst Control inputs (ADSC, ADSP, and ADV), Write Enables (BW[A:D], and BWE), and Global Write (GW). Asynchronous inputs include the Output Enable (OE) and the ZZ pin. Addresses and chip enables are registered at rising edge of clock when either Address Strobe Processor (ADSP) or Address Strobe Controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the Advance pin (ADV). Address, data inputs, and write controls are registered on-chip to initiate a self-timed Write cycle.This part supports Byte Write operations (see Pin Descriptions and Truth Table for further details). Write cycles can be one to four bytes wide as controlled by the byte write control inputs. GW active LOW causes all bytes to be written. This device incorporates an additional pipelined enable register which delays turning off the output buffers an additional cycle when a deselect is executed.This feature allows depth expansion without penalizing system performance. The CY7C1340G operates from a +3.3V core power supply while all outputs operate with a +3.3V or a +2.5V supply. All inputs and outputs are JEDEC-standard JESD8-5-compatible. Selection Guide 250 MHz 200 MHz 166 MHz 133 MHz Unit Maximum Access Time 2.6 2.8 3.5 4.0 ns Maximum Operating Current 325 265 240 225 mA Maximum CMOS Standby Current 40 40 40 40 mA Note: 1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com. Cypress Semiconductor Corporation Document #: 38-05522 Rev. *D • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised July 5, 2006 CY7C1340G Functional Block Diagram ADDRESS REGISTER A0,A1,A 2 A[1:0] MODE ADV CLK BURST Q1 COUNTER AND LOGIC CLR Q0 ADSC ADSP BWD DQD BYTE WRITE REGISTER DQD BYTE WRITE DRIVER BWC DQc BYTE WRITE REGISTER DQC BYTE WRITE DRIVER DQB BYTE WRITE REGISTER DQB BYTE WRITE DRIVER BWB BWA BWE GW CE1 CE2 CE3 OE ZZ SENSE AMPS OUTPUT REGISTERS OUTPUT BUFFERS DQs E DQA BYTE WRITE DRIVER DQA BYTE WRITE REGISTER ENABLE REGISTER MEMORY ARRAY INPUT REGISTERS PIPELINED ENABLE SLEEP CONTROL Document #: 38-05522 Rev. *D Page 2 of 16 CY7C1340G Pin Configurations CE1 CE2 BWD BWC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A 100-Pin TQFP Pinout NC DQc DQc VDDQ VSSQ DQc DQc DQc DQc VSSQ VDDQ DQc DQc NC VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD NC BYTE C 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 CY7C1340G NC DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA NC BYTE B BYTE A A A A A A A A MODE A A A A A1 A0 NC/72M NC/36M VSS VDD NC/18M NC/9M 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 BYTE D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Pin Definitions Pin Type Description A0, A1, A InputAddress Inputs used to select one of the 128K address locations. Sampled at the rising edge Synchronous of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A[1:0] are fed to the two-bit counter. BWA, BWB, BWC, BWD InputByte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM. Synchronous Sampled on the rising edge of CLK. GW InputGlobal Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global Synchronous write is conducted (ALL bytes are written, regardless of the values on BW[A:D] and BWE). BWE InputByte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be Synchronous asserted LOW to conduct a byte write. Document #: 38-05522 Rev. *D Page 3 of 16 CY7C1340G Pin Definitions (continued) Pin CLK Type Description InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. CE1 InputChip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE1 is sampled only when a new external address is loaded. CE2 InputChip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE1 and CE3 to select/deselect the device. CE2 is sampled only when a new external address is loaded. CE3 InputChip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE1 and CE2 to select/deselect the device. CE3 is sampled only when a new external address is loaded. OE InputOutput Enable, asynchronous input, active LOW. Controls the direction of the DQ pins. When Asynchronous LOW, the DQ pins behave as outputs. When deasserted HIGH, DQ pins are tri-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV InputAdvance Input signal, sampled on the rising edge of CLK, active LOW. When asserted, it Synchronous automatically increments the address in a burst cycle. ADSP InputAddress Strobe from Processor, sampled on the rising edge of CLK, active LOW. When Synchronous asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC InputAddress Strobe from Controller, sampled on the rising edge of CLK, active LOW. When Synchronous asserted LOW, addresses presented to the device are captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ InputZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a non-time-critical Asynchronous “sleep” condition with data integrity preserved.During normal operation, this pin has to be low or left floating. ZZ pin has an internal pull-down. DQs I/OBidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by Synchronous the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs are placed in a tri-state condition. VDD Power Supply Power supply inputs to the core of the device. Ground Ground for the core of the device. VDDQ I/O Power Supply Power supply for the I/O circuitry. VSSQ I/O Ground Ground for the I/O circuitry. VSS MODE NC,NC/9M, NC/18M, NC/36M, NC/72M InputStatic Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode Pin has an internal pull-up. No Connects. Not internally connected to the die.NC/9M,NC/18M,NC/36M,NC/72M are address expansion pins are not internally connected to the die. Document #: 38-05522 Rev. *D Page 4 of 16 CY7C1340G Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. The CY7C1340G supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium and i486™ processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BW[A:D]) inputs. A Global Write Enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed write circuitry. Synchronous Chip Selects CE1, CE2, CE3 and an asynchronous Output Enable (OE) provide for easy bank selection and output tri-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) chip selects are all asserted active, and (3) the write signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs is stored into the address advancement logic and the Address Register while being presented to the memory core. The corresponding data is allowed to propagate to the input of the Output Registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within tCO if OE is active LOW. The only exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always tri-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single read cycles are supported. The CY7C1340G is a double-cycle deselect part. Once the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output will tri-state immediately after the next clock rise. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) chip select is asserted active. The address presented is loaded into the address register and the address advancement logic while being delivered to the memory core. The write signals (GW, BWE, and BW[A:D]) and ADV inputs are ignored during this first cycle. ADSP triggered write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQx inputs is written into the corresponding address location in the memory core. If GW is HIGH, Document #: 38-05522 Rev. *D then the write operation is controlled by BWE and BW[A:D] signals. The CY7C1340G provides byte write capability that is described in the Write Cycle Description table. Asserting the Byte Write Enable input (BWE) with the selected Byte Write input will selectively write to only the desired bytes. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. Because the CY7C1340G is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQ inputs. Doing so will tri-state the output drivers. As a safety precaution, DQ are automatically tri-stated whenever a write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC ADSC write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted HIGH, (3) chip select is asserted active, and (4) the appropriate combination of the write inputs (GW, BWE, and BW[A:D]) are asserted active to conduct a write to the desired byte(s). ADSC triggered write accesses require a single clock cycle to complete. The address presented is loaded into the address register and the address advancement logic while being delivered to the memory core. The ADV input is ignored during this cycle. If a global write is conducted, the data presented to the DQX is written into the corresponding address location in the memory core. If a byte write is conducted, only the selected bytes are written. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. Because the CY7C1340G is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQX inputs. Doing so will tri-state the output drivers. As a safety precaution, DQX are automatically tri-stated whenever a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1340G provides a two-bit wraparound counter, fed by A[1:0], that implements either an interleaved or linear burst sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. Both read and write burst operations are supported. Asserting ADV LOW at clock rise will automatically increment the burst counter to the next address in the burst sequence. Both read and write burst operations are supported. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CEs, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Page 5 of 16 CY7C1340G Linear Burst Address Table (MODE = GND) Interleaved Burst Address Table (MODE = Floating or VDD) First Address A1, A0 00 01 10 11 Second Address A1, A0 01 00 11 10 Third Address A1, A0 10 11 00 01 First Address A1, A0 00 01 10 11 Fourth Address A1, A0 11 10 01 00 Second Address A1, A0 01 10 11 00 Third Address A1, A0 10 11 00 01 Fourth Address A1, A0 11 00 01 10 ZZ Mode Electrical Characteristics Parameter IDDZZ tZZ tZZREC tZZI tRZZI Description Snooze mode standby current Device operation to ZZ ZZ recovery time ZZ active to snooze current ZZ inactive to exit snooze current Test Conditions ZZ > VDD − 0.2V ZZ > VDD − 0.2V ZZ < 0.2V This parameter is sampled This parameter is sampled Min. Max. 40 2tCYC 2tCYC 2tCYC 0 Unit mA ns ns ns ns Truth Table[2, 3, 4, 5, 6] Address Used CE1 CE2 CE3 Deselected Cycle, Power Down None H X X Operation Deselected Cycle, Power Down None L L X Deselected Cycle, Power Down None L X H Deselected Cycle, Power Down None L L X ZZ ADSP ADSC ADV WRITE OE CLK DQ L X L X X X L-H Tri-State L L X X X X L-H Tri-State L L X X X X L-H Tri-State L H L X X X L-H Tri-State Deselected Cycle, Power Down None L X H L H L X X X L-H Tri-State ZZ Mode, Power-Down None X X X H X X X X X X Tri-State Read Cycle, Begin Burst External L H L L L X X X L L-H Q Read Cycle, Begin Burst External L H L L L X X X H L-H Tri-State Write Cycle, Begin Burst External L H L L H L X L X L-H D Read Cycle, Begin Burst External L H L L H L X H L L-H Q Read Cycle, Begin Burst External L H L L H L X H H L-H Tri-State Next X X X L H H L H L L-H Q Read Cycle, Continue Burst Read Cycle, Continue Burst Next X X X L H H L H H L-H Tri-State Read Cycle, Continue Burst Next H X X L X H L H L L-H Q Read Cycle, Continue Burst Next H X X L X H L H H L-H Tri-State Write Cycle, Continue Burst Next X X X L H H L L X L-H D Write Cycle, Continue Burst Next H X X L X H L L X L-H D Read Cycle, Suspend Burst Current X X X L H H H H L L-H Q Read Cycle, Suspend Burst Current X X X L H H H H H L-H Tri-State Read Cycle, Suspend Burst Current H X X L X H H H L L-H Q Read Cycle, Suspend Burst Current H X X L X H H H H L-H Tri-State Write Cycle, Suspend Burst Current X X X L H H H L X L-H D Write Cycle, Suspend Burst Current H X X L X H H L X L-H D Notes: 2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. 3. WRITE = L when any one or more Byte Write enable signals (BWA, BWB, BWC, BWD) and BWE = L or GW = L. WRITE = H when all Byte write enable signals (BWA, BWB, BWC, BWD), BWE, GW = H. 4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't care for the remainder of the write cycle. 6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). Document #: 38-05522 Rev. *D Page 6 of 16 CY7C1340G Partial Truth Table for Read/Write[2, 7] Function GW BWE BWA BWB BWC BWD Read H H X X X X Read H L H H H H Write byte A - DQA H L L H H H Write byte B - DQB H L H L H H Write byte C - DQC H L H H L H Write byte D - DQD H L H H H L Write all bytes H L L L L L Write all bytes L X X X X X Note: 7. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active. Document #: 38-05522 Rev. *D Page 7 of 16 CY7C1340G Maximum Ratings DC Input Voltage ................................... –0.5V to VDD + 0.5V (Above which the useful life may be impaired. For user guidelines, not tested.) Current into Outputs (LOW)......................................... 20 mA Static Discharge Voltage............................................ >2001V Storage Temperature .................................... –65°C to +150° (per MIL-STD-883,Method 3015) Ambient Temperature with Power Applied............................................. –55°C to +125°C Latch -up Current..................................................... >200 mA Operating Range Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V Supply Voltage on VDDQ Relative to GND ...... –0.5V to +VDD Range DC Voltage Applied to Outputs in tri-state ............................................ –0.5V to VDDQ + 0.5V Commercial Industrial Ambient Temperature (TA) 0°C to +70°C –40°C to +85°C VDD VDDQ 3.3V −5%/+10% 2.5V −5% to VDD Electrical Characteristics Over the Operating Range [8, 9] Parameter Description Test Conditions Min. Max. Unit VDD Power Supply Voltage 3.135 3.6 V VDDQ I/O Supply Voltage 2.375 VDD V VOH Output HIGH Voltage for 3.3V I/O, IOH = –4.0 mA 2.4 for 2.5V I/O, IOH = –1.0 mA 2.0 VOL Output LOW Voltage VIH Input HIGH Voltage[8] for 3.3V I/O VIL Input LOW Voltage[8] for 2.5V I/O IX Input Leakage Current except ZZ and MODE GND ≤ VI ≤ VDDQ Input Current of MODE Input = VSS –30 for 3.3V I/O, IOL = 8.0 mA 0.4 V VDD + 0.3V V for 2.5V I/O 1.7 VDD + 0.3V V for 3.3V I/O –0.3 0.8 V –0.3 0.7 V –5 5 µA Input = VSS µA 5 µA 30 µA µA –5 Input = VDD IOZ Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled IDD VDD Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC Automatic CE Power-down Current—TTL Inputs V 2.0 Input = VDD ISB1 V 0.4 for 2.5V I/O, IOL = 1.0 mA Input Current of ZZ V 5 µA 4-ns cycle, 250 MHz 325 mA 5-ns cycle, 200 MHz 265 mA 6-ns cycle, 166 MHz 240 mA 7.5-ns cycle, 133 MHz 225 mA 120 mA 110 mA VDD = Max., Device Deselected, 4-ns cycle, 250 MHz VIN ≥ VIH or VIN ≤ VIL, f = fMAX = 5-ns cycle, 200 MHz 1/tCYC 6-ns cycle, 166 MHz 7.5-ns cycle, 133 MHz –5 100 mA 90 mA ISB2 Automatic CE Power-down Current—CMOS Inputs VDD = Max., Device Deselected, All speeds VIN ≤ 0.3V or VIN > VDDQ – 0.3V, f=0 40 mA ISB3 Automatic CE Power-down Current—CMOS Inputs VDD = Max., Device Deselected, 4-ns cycle, 250 MHz or VIN ≤ 0.3V or VIN > VDDQ – 5-ns cycle, 200 MHz 0.3V, f = fMAX = 1/tCYC 6-ns cycle, 166 MHz 105 mA 95 mA 85 mA 75 mA 45 mA 7.5-ns cycle, 133 MHz ISB4 Automatic CE Power-down VDD = Max., Device Deselected, All speeds Current—TTL Inputs VIN ≥ VIH or VIN ≤ VIL, f = 0 Notes: . 8. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC)> –2V (Pulse width less than tCYC/2). 9. TPower-up: Assumes a linear ramp from 0V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD. Document #: 38-05522 Rev. *D Page 8 of 16 CY7C1340G Capacitance[10] Parameter Description CIN Input Capacitance CCLK Clock Input Capacitance CI/O Input/Output Capacitance 100 TQFP Max. Test Conditions TA = 25°C, f = 1 MHz, VDD = 3.3V VDDQ = 3.3V Unit 5 pF 5 pF 5 pF 100 TQFP Package Unit Thermal Characteristics[10] Parameter Description Test Conditions ΘJA Thermal Resistance (Junction to Ambient) ΘJC Thermal Resistance (Junction to case) Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51. 30.32 °C/W 6.85 °C/W AC Test Loads and Waveforms 3.3V I/O Test Load R = 317Ω 3.3V OUTPUT ALL INPUT PULSES VDDQ OUTPUT RL = 50Ω Z0 = 50Ω 10% 90% 10% 90% GND 5 pF R = 351Ω ≤ 1ns ≤ 1ns VT = 1.5V INCLUDING JIG AND SCOPE (a) (c) (b) 2.5V I/O Test Load R = 1667Ω 2.5V OUTPUT Z0 = 50Ω 10% R =1538Ω VT = 1.25V INCLUDING JIG AND SCOPE 90% 10% 90% GND 5 pF (a) ALL INPUT PULSES VDDQ OUTPUT RL = 50Ω (b) ≤ 1ns ≤ 1ns (c) Note: 10. Tested initially and after any design or process change that may affect these parameters. Document #: 38-05522 Rev. *D Page 9 of 16 CY7C1340G Switching Characteristics Over the Operating Range [12, 13, 14, 15, 16] –250 Parameter tPOWER Description Min. [11] Max. –200 Min. Max. –166 Min. Max. –133 Min. Max. Unit VDD(Typical) to the first Access 1.0 1.0 1.0 1.0 ms tCYC Clock Cycle Time 4.0 5.0 6.0 7.5 ns tCH Clock HIGH 1.7 2.0 2.5 3.0 ns tCL Clock LOW 1.7 2.0 2.5 3.0 ns Clock Output Times tCO Data Output Valid After CLK Rise tDOH Data Output Hold After CLK Rise [12, 13, 14] 2.6 1.0 2.8 1.0 1.5 1.5 ns Clock to Low-Z Clock to High-Z[12, 13, 14] 2.6 2.8 3.5 4.0 ns tOEV OE LOW to Output Valid 2.6 2.8 3.5 4.0 ns tOEHZ OE LOW to Output OE HIGH to Output High-Z[12, 13, 14] 0 0 ns tCHZ tOELZ 0 4.0 tCLZ Low-Z[12, 13, 14] 0 3.5 0 2.6 0 0 2.8 ns 0 3.5 ns 4.0 ns Set-up Times tAS Address Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tADS ADSC, ADSP Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tADVS ADV Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tWES GW, BWE, BWX Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tDS Data Input Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tCES Chip Enable Set-up Before CLK Rise 1.2 1.2 1.5 1.5 ns tAH Address Hold After CLK Rise 0.3 0.5 0.5 0.5 ns tADH ADSP, ADSC Hold After CLK Rise 0.3 0.5 0.5 0.5 ns tADVH ADV Hold After CLK Rise 0.3 0.5 0.5 0.5 ns tWEH GW, BWE, BWX Hold After CLK Rise 0.3 0.5 0.5 0.5 ns tDH Data Input Hold After CLK Rise 0.3 0.5 0.5 0.5 ns tCEH Chip Enable Hold After CLK Rise 0.3 0.5 0.5 0.5 ns Hold Times Notes: 11. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD minimum initially before a read or write operation can be initiated. 12. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 13. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve High-Z prior to Low-Z under the same system conditions. 14. This parameter is sampled and not 100% tested. 15. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V. 16. Test conditions shown in (a) of AC Test Loads unless otherwise noted. Document #: 38-05522 Rev. *D Page 10 of 16 CY7C1340G Switching Waveforms Read Timing[17] tCYC CLK tCH tCL tADS tADH ADSP tADS tADH ADSC tAS ADDRESS tAH A1 A2 tWES A3 Burst continued with new base address tWEH GW, BWE,BW [A:D] Deselect cycle tCES tCEH CE tADVS tADVH ADV ADV suspends burst OE t Data Out (Q) High-Z CLZ t OEHZ Q(A1) tOEV tCO t OELZ tDOH Q(A2) t CHZ Q(A2 + 1) Q(A2 + 2) Q(A2 + 3) Q(A2) Q(A2 + 1) Q(A3) t CO Single READ BURST READ DON’T CARE Burst wraps around to its initial state UNDEFINED Note: 17. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document #: 38-05522 Rev. *D Page 11 of 16 CY7C1340G Switching Waveforms (continued) Write Timing[17, 18] t CYC CLK tCH tADS tCL tADH ADSP tADS ADSC extends burst tADH tADS tADH ADSC tAS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst tWES tWEH BWE, BW[A:D] tWES tWEH GW tCES tCEH CE tADVS tADVH ADV ADV suspends burst OE t DS Data in (D) High-Z t OEHZ t DH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Note: 18. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A:D] LOW. Document #: 38-05522 Rev. *D Page 12 of 16 CY7C1340G Switching Waveforms (continued) Read/Write Timing[17, 19, 20] tCYC CLK tCL tCH tADS tADH tAS tAH ADSP ADSC ADDRESS A1 A2 A3 A4 A5 A6 D(A5) D(A6) tWES tWEH BWE, BW[A:D] tCES tCEH CE ADV OE tDS tDH tCO Data In (D) tOELZ High-Z tCLZ Data Out (Q) High-Z Q(A1) Back-to-Back READs tOEHZ D(A3) Q(A2) Q(A4) Single WRITE Q(A4+1) Q(A4+2) BURST READ DON’T CARE Q(A4+3) Back-to-Back WRITEs UNDEFINED Notes: 19. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC. 20. GW is HIGH. Document #: 38-05522 Rev. *D Page 13 of 16 CY7C1340G Switching Waveforms (continued) ZZ Mode Timing [21, 22] CLK t ZZ ZZ I t ZZREC t ZZI SUPPLY I DDZZ t RZZI ALL INPUTS (except ZZ) Outputs (Q) DESELECT or READ Only High-Z DON’T CARE Notes: 21. Device must be deselected when entering ZZ mode. See truth table for all possible signal conditions to deselect the device. 22. DQs are in high-Z when exiting ZZ sleep mode. Document #: 38-05522 Rev. *D Page 14 of 16 CY7C1340G Ordering Information Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit www.cypress.com for actual products offered. Speed (MHz) 133 Package Diagram Ordering Code CY7C1340G-133AXC Operating Range Package Type 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial CY7C1340G-133AXI 166 Industrial CY7C1340G-166AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial CY7C1340G-166AXI 200 Industrial CY7C1340G-200AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial CY7C1340G-200AXI 250 Industrial CY7C1340G-250AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free Commercial CY7C1340G-250AXI Industrial Package Diagram 100-Pin TQFP (14 x 20 x 1.4 mm) (51-85050) 16.00±0.20 1.40±0.05 14.00±0.10 100 81 80 1 20.00±0.10 22.00±0.20 0.30±0.08 0.65 TYP. 30 12°±1° (8X) SEE DETAIL A 51 31 50 0.20 MAX. R 0.08 MIN. 0.20 MAX. 0.10 1.60 MAX. 0° MIN. SEATING PLANE STAND-OFF 0.05 MIN. 0.15 MAX. 0.25 NOTE: 1. JEDEC STD REF MS-026 GAUGE PLANE 0°-7° R 0.08 MIN. 0.20 MAX. 2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH 3. DIMENSIONS IN MILLIMETERS 0.60±0.15 0.20 MIN. 51-85050-*B 1.00 REF. DETAIL A Intel and Pentium are registered trademarks, and i486 is a trademark, of Intel Corporation. PowerPC is a registered trademark of IBM. All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-05522 Rev. *D Page 15 of 16 © Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. CY7C1340G Document History Page Document Title: CY7C1340G 4-Mb (128K x 32) Pipelined DCD Sync SRAM Document Number: 38-05522 REV. Orig. of ECN NO. Issue Date Change Description of Change ** 224370 See ECN RKF New Data Sheet *A 288909 See ECN VBL In Ordering Info Section, change TQFP to PB-Free TQFP *B 332895 See ECN SYT Modified Address Expansion balls in the pinouts for 100 TQFP Package as per JEDEC standards and updated the Pin Definitions accordingly Modified VOL, VOH test conditions Removed 200Mhz Speed Bin Replaced TBD’s for ΘJA and ΘJC to their respective values on the Thermal Resistance table Updated the Ordering Information by shading and unshading MPNs as per availability *C 419256 See ECN RXU Converted from Preliminary to Final Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901 North First Street” to “198 Champion Court” Modified test condition from VIH < VDD to VIH < VDD Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the Electrical Characteristics Table Replaced Package Name column with Package Diagram in the Ordering Information table Replaced Package Diagram of 51-85050 from *A to *B Updated the Ordering Information *D 480368 See ECN VKN Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND. Updated the Ordering Information table. Document #: 38-05522 Rev. *D Page 16 of 16