Datasheet 8 Gbps Bi-Directional SFP+ Transceiver SFP-8GD-LR Features Designed for SFF-8472 compliance (SFP) Up to 8.5 Gbps data rates - 2.125/4.25/8.5 Gbps Fibre Channel Single-mode optics (Duplex LC) Dual-fiber, bi-directional Class 1 laser (Tx): 1310 nm Up to 10 km on 9/125 μm SMF Digital Diagnostics (SFF-8472) Commercial operating temperature range RoHS compliant and Lead Free Metal enclosure, for lower EMI Absolute Maximum Ratings* Parameter Maximum Supply Voltage Case Operating Temperature Storage Temperature Relative Humidity (Non-Condensing) Symbol Minimum Maximum Unit Vcc TA -0.5 4.0 V Note - -5 85 ºC - TS RH -40 85 ºC - 0 85 % - Note *Exceeding the limits listed in the table may damage the transceiver module permanently General Specifications Parameter Symbol Minimum Maximum Unit Data Rate BR 2.125 8.5 Gbps 1 Bit Error Rate BER - 10-12 - 2 LMAX1 - 10 km 3 Max. Supported Link Length on 9/125 μm SMF, 2.125, 4.25, 8.5 Gbps Notes: 1. 2. 3. 2x/4x/8x Fibre Channel compliant. Tested with a PRBS 27-1 test pattern. Distances are based on IEEE 802.3 standards and FC-PI-4 Rev. 7.00 (“Fibre Channel Physical Interface-4 Specification”. American National Standard for Information Systems, September 20, 2007.) 1 Datasheet Electrical Specifications Parameter Supply Voltage Supply Current Symbol Minimum Maximum Unit Note Vcc Icc 3.00 3.60 V 1 - 300 mA 1 Rin 80 120 Ω 2 V in, pp 90 350 mV - Vcc Vee + 0.8 V - V 3 Transmitter Input Differential Impedance Single Ended Data Input Swing Transmit Disable Voltage VD 2 Transmit Enable Voltage VEN Vee V out, pp 150 425 mV 4 tr, tf - 120 ps 5 Receiver Single Ended Data Output Swing Data Output Rise/Fall Time @ 2.125 Gbps, 4.25 Gbps Data Output Rise/Fall Time @ 8.5 Gbps tr, tf - 60 ps 5 LOS Fault VLOS fault 2 VccHOST V 6 LOS Normal VLOS norm Vee Vee + 0.8 V 6 Power Supply Rejection PSR 100 - mVpp 7 Deterministic Jitter Contribution < 4.25 Gbps RX Δ DJ - 51.7 ps 8,9 Total Jitter Contribution < 4.25 Gbps RX Δ TJ - 122.4 ps 9 Deterministic Jitter Contribution = 4.25 Gbps RX Δ DJ - 25.9 ps 8,9 Total Jitter Contribution = 4.25 Gbps RX Δ TJ - 61.2 ps 9 Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. Module power consumption never exceeds 1W. AC coupled. Or open circuit. Into 100 ohm differential termination. 20 – 80 %. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA) 6, September 14, 2000. The Power Supply Rejection applies for a supply voltage range of 3.1 to 3.6 V. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ. For 8.5 Gbps operation, Jitter values for gamma T and gamma R are controlled by TDP and stressed receiver sensitivity. 2 Datasheet Optical Specifications Parameter Symbol Minimum Maximum Unit Note Output Optical Power @ 8.5 Gbps PO, RH -8.4 0.5 dBm 1 Output Optical Power @ 2.125, 4.25 Gbps Transmitter PO, RL -8.4 -3 dBm 2 Optical Wavelength λ 1285 1345 nm 3 Spectral Width σ - 1 nm 3 Optical Modulation Amplitude OMA -5.4 - dBm 3,4 Transmitter and Dispersion Penalty @ 8.5 Gbps TDP - 3.2 dB 5 Optical Rise/Fall Time @ 2.125, 4.25 Gbps tr/tf - 90 ps 6 Relative Intensity Noise RIN - -128 dB/Hz - Receiver Unstressed Receiver OMA Sensitivity @ 8.5 Gbps RSENSr - -13.8 dBm 7 Unstressed Receiver OMA Sensitivity @ 4.25 Gbps RSENS4 - -15.4 dBm 7 Unstressed Receiver OMA Sensitivity @ 2.125 Gbps RSENS2 - -18.2 dBm 7 Maximum Average Receiver Power RxMAX 0.5 - dBm - λC 1260 1360 nm - - 12 - dB - Optical Center Wavelength Optical Return Loss LOS De-Assert LOSD - -19 dBm - LOS Assert LOSA -30 - dBm - - 0.5 - dB - LOS Hysteresis Notes: 1. 2. 3. 4. 5. 6. 7. High Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. Low Bandwidth Mode. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. Also specified to meet curves in FC-PI-4 Rev 7.00 (“Fibre Channel Physical Interface-4 Specification”. American National Standard for Information Systems, September 20, 2007) Figures 21, 22, and 23, which allow trade- off between wavelength, spectral width and OMA. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. For 8.5 Gb/s operation, Jitter values for gamma T and gamma R are controlled by TDP and stressed receiver sensitivity. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered. Measured with conformance signals defined in FC-PI-4 Rev. 10.0 specifications. Value in OMA. Measured with PRBS 27-1 at 10-12 BER. 3 Datasheet Pin Descriptions Notes: Pin Function Name/Description Note 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. 2 3 TDIS Transmitter Disable. Laser Output Disabled on High or Open. 3 4 SDA 2-wire Serial Interface Data Line (MOD-DEF2) 4 5 SCA 2-wire Serial Interface Clock (MOD-DEF1) 4 6 MOD_ABS Module Absent, connected to VEET or VEER 4 7 RS0 Rx Rate Select: Open or Low = 2.125 or 4.25 Gbps Fibre Channel (Low Bandwidth) High = 8.5 Gbps Fibre Channel (High Bandwidth) 5 8 LOS Loss of Signal Indication. Logic 0 Indicates Normal Operation. 6 9 RS1 Tx Rate Select: Open or Low = 2.125 or 4.25 Gbps Fibre Channel (Low Bandwidth) High = 8.5 Gbps Fibre Channel (High Bandwidth) 5 10 VEER Receiver Ground (Common with Transmitter Ground) 1 11 VEER Receiver Ground (Common with Transmitter Ground) 1 12 RD- Receiver Inverted DATA Out. AC Coupled. - 13 RD+ Receiver Non-Inverted DATA Out. AC Coupled. - 14 VEER Receiver Ground (Common with Transmitter Ground) 1 15 VCCR Receiver Power Supply - 16 VCCT Transmitter Power Supply - 17 VEET Transmitter Ground (Common with Receiver Ground) 1 18 TD+ Transmitter Non-Inverted DATA In. AC Coupled. - 19 TD- Transmitter Inverted DATA In. AC Coupled. - 20 VEET Transmitter Ground (Common with Receiver Ground) 1 1. 2. 3. 4. 5. 6. Circuit ground is internally isolated from chassis ground. TFAULT is an open collector/drain output, which should be pulled up with a 4.7 k – 10 kohms resistor on the host board if intended for use. Pull up voltage should be between 2.0 V to Vcc + 0.3 V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to < 0.8 V. Laser output disabled on TDIS > 2.0 V or open, enabled on TDIS < 0.8 V. Should be pulled up with 4.7 k – 10 kohms on host board to a voltage between 2.0 V and 3.6 V. MOD_ABS pulls line low to indicate module is plugged in. Rate select can also be set through the 2-wire bus in accordance with SFF-8472 v. 10.1. Rx Rate Select is set at Bit 3, Byte 110, Address A2h. Tx Rate Select is set at Bit 3, Byte 118, Address A2h. Note: writing a “1” selects maximum bandwidth operation. Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. LOS is open collector output. Should be pulled up with 4.7 k – 10 kohms on host board to a voltage between 2.0 V and 3.6 V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 4 Datasheet Diagram of Host Board Connector Block Pin Numbers and Names Towards Bezel 1 VeeT 2 TX_Fault 3 TX_Disable 4 SDA 5 SCL 6 MOD_ABS 7 RS0 8 RX_LOS 9 RS1 10 VeeR Mechanical Dimensions 5 VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 Towards ASIC Datasheet Data Rate (Mbps) Wavelength (nm) Connector Bail Latch Color Max. Link Length (km) SFP+, 2.125 / 4.25 / 8.5 Gb/s, SM, with Digital Diagnostics. 2125 - 8500 1310 Duplex LC Blue 0 -10 Model Description Ordering Information SFP-8GD-LR Regulatory and Industry Compliances Class 1 Laser Product, Complies with 21CFR 1040.10, 1040.11 and EN 60825-1 Certified by one or more of the following agencies: TÜV, UL, CSA RoHS Directive; China RoHS; California RoHS Law, REACH Directive SVHC Please visit http://www.mrv.com or contact a sales representative for more information and for ordering. MRV has more than 50 offices throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com. Please e-mail us at [email protected] or call us for assistance. MRV Los Angeles 20415 Nordhoff St. Chatsworth, CA 91311 800-338-5316 818-773-0900 MRV Boston 295 Foster St. Littleton, MA 01460 800-338-5316 978-952-4700 MRV International Business Park Moerfelden Waldeckerstrasse 13 64546 Moerfelden-Walldorf Germany Tel. (49) 6105/2070 Fax (49) 6105/207-100 All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact MRV Communications for more information. MRV Communications and the MRV Communications logo are trademarks of MRV Communications, Inc. Other trademarks are the property of their respective holders. MRV-OP-SFP8GDLR-031609 3020073-001 Rev. A1 Copyright ©2009 MRV Communications, Inc. All Rights Reserved.