MRV SFP-10GD-LR

Datasheet
10 Gbps 10 km Single-Mode SFP+ Transceiver
SFP-10GD-LR
Features
Hot-pluggable SFP+ footprint
Supports 9.95 to 10.52 Gbps bit rates
Power dissipation < 1W
RoHS-6 compliant (lead-free)
Commercial temperature range -5°C to 70°C
Single 3.3 V power supply
Maximum link length of 10 km
Uncooled 1310 nm DFB laser
Receiver limiting electrical interface
Duplex LC connector
Built-in digital diagnostic functions
MRV’s SFP-10GD-LR 10 Gbps Enhanced Small Form Factor Pluggable SFP+ transceivers are designed for use in 10-Gigabit Ethernet
and 10 Gigabit Fibre Channel links up to 10km over single-mode fiber. They are compliant with SFF-8431, SFF-8432 and IEEE 802.3ae
10GBASE-LR/LW. Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472. The SFP-10GD-LR is
a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s
recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module. The transceiver is RoHS
compliant and lead free per Directive 2002/95/EC.
Absolute Maximum Ratings*
Parameter
Maximum Supply Voltage
Case Operating Temperature
Storage Temperature
Relative Humidity (Non-Condensing)
Symbol
Minimum
Typical
Maximum
Unit
Note
Vcc
TA
-0.5
-
4.0
V
-
-5
-
70
ºC
-
TS
RH
-40
-
85
ºC
-
0
-
85
%
-
*Exceeding the limits listed in the table may damage the transceiver module permanently
Electrical Specifications
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Note
Supply Voltage
Vcc
3.14
3.30
3.46
V
-
Supply Current
Icc
-
200
285
mA
-
Input Differential Impedance
Rin
-
100
-
Ω
1
Differential Data Input Swing
Transmitter
V in, pp
180
-
700
mV
-
Transmit Disable Voltage
VD
2
-
Vcc
V
-
Transmit Enable Voltage
VEN
Vee
-
Vee+0.8
V
-
V out, pp
300
-
850
mV
2, 6
Receiver
Differential Data Output Swing
tr, tf
28
-
-
ps
3
LOS Fault
Output Rise Time, Fall Time
VLOS fault
2
-
VccHOST
V
4
LOS Normal
VLOS norm
Vee
-
Vee+0.8
V
4
mVpp
5
Power Supply Noise Tolerance
Notes:
1.
2.
3.
4.
5.
6.
VccT/ VccR
Per SFF-8431 Rev 2.1
Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
Into 100Ω differential termination.
20 – 80 % . Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s in sequence in the
PRBS 9 is an acceptable alternative. SFF-8431 Rev 2.1
LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of
signal is logic 1.
See section 2.8.3 of SFF-8431. Rev 2.1
The SFP-10GD-LR is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should
follow the IC manufacturer’s recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+
module.
1
Datasheet
Pin Descriptions
Notes:
Pin
Function
Name/Description
Note
1
VEET
Transmitter Ground
1
2
TFAULT
Transmitter Fault
2
3
TDIS
Transmitter Disable. Laser output disabled on high or open.
3
4
SDA
2-wire Serial Interface Data Line
2
5
SCL
2-wire Serial Interface Clock Line
2
6
MOD_ABS
Module Absent. Grounded within the module.
2
7
RS0
Rate Select 0. Not Used.
4
8
RX_LOS
Loss of Signal indication. Logic 0 indicates normal operation.
5
9
RS1
Rate Select 1. Not Used.
4
10
VEER
Receiver Ground
1
11
VEER
Receiver Ground
1
12
RD-
Receiver Inverted DATA out. AC Coupled.
13
RD+
Receiver Non-inverted DATA out. AC Coupled.
14
VEER
Receiver Ground
15
VCCR
Receiver Power Supply
16
VCCT
Transmitter Power Supply
17
VEET
Transmitter Ground
18
TD+
Transmitter Non-Inverted DATA in. AC Coupled.
19
TD-
Transmitter Inverted DATA in. AC Coupled.
20
VEET
Transmitter Ground
1.
2.
3.
4.
5.
1
1
1
Circuit ground is internally isolated from chassis ground.
TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if
intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused
by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal
operation. In the low state, the output is pulled to <0.8V.
Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
Internally pulled down per SFF-8431 Rev 2.0
LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic
0 indicates normal operation; logic 1 indicates loss of signal.
Diagram of Host Board Connector Block Pin Numbers and Names
1
VeeT
2
TX_Fault
3
Towards
Bezel
SDA
5
SCL
6
MOD_ABS
7
RS0
8
RX_LOS
10
20
TD-
19
TD+
18
VeeT
17
VccT
16
VccR
15
VeeR
14
TX_Disable
4
9
VeeT
RD+
13
RD-
12
VeeR
11
RS1
VeeR
2
Towards
ASIC
Datasheet
Optical Specifications
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Note
Optical Modulation Amplitude (OMA)
POMA
-5.2
-
-
dBm
-
Average Launch Power
PAVE
-8.2
-
0.5
dBm
1
λ
1260
-
1355
nm
-
SMSR
30
-
-
dB
-
ER
3.5
-
-
dB
-
Transmitter and Dispersion Penalty
TDP
-
-
3.2
dB
-
-
-
-30
dBm
-
Transmitter
Optical Wavelength
Side-Mode Suppression Ratio
Optical Extinction Ratio
Average Launch Power of OFF Transmitter
Poff
Tx Jitter
Txj
Relative Intensity Noise
RIN
-
-
-128
dB/Hz
-
Receiver Sensitivity (OMA) @ 10.3Gbps
RSENS1
-
-
-12.6
dBm
2
Stressed Receiver Sensitivity (OMA) @ 10.3Gbps
RSENS2
-
-
-10.3
dBm
3
PAVE
-14.2
-
+ 0.5
dBm
-
λC
1260
-
1600
nm
-
Per IEEE 802.3ae requirements
-
Receiver
Average Receiver Power
Optical Center Wavelength
Receiver Reflectance
Rrx
-
-
-12
dB
-
LOS De-Assert
LOSD
-
-
-17
dBm
-
LOS Assert
LOSA
-30
-
-
dBm
-
-
0.5
-
-
dB
-
Note
LOS Hysteresis
Notes:
1.
2.
3.
Average Power figures are informative only, per IEEE802.3ae.
Valid between 1260 and 1355 nm. Measured with worst ER; BER<10-12; 231 – 1 PRBS.
Valid between 1260 and 1355 nm. Per IEEE 802.3ae.
General Specifications
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Bit Rate
BR
9.95
10.3
10.52
Gbps
1
Bit Error Ratio
BER
-
-
10-12
-
2
Max. Supported Link Length
SMAX
-
10
-
km
1
Notes:
1.
2.
10GBASE-LR, 10GBASE-LW, 10G Fibre Channel
Tested with a 231 – 1 PRBS
Environmental Specifications
Parameter
Case Operating Temperature
Storage Temperature
Symbol
Minimum
Typical
Maximum
Unit
Note
Top
Tsto
-5
-
70
ºC
-
-40
-
85
ºC
-
Regulatory and Industry Compliances
MRV transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the
Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available
at MRV Corporation upon request.
3
Datasheet
Digital Diagnostics Functions
MRV’s SFP-10GD-LR SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFF-8472. It is very closely
related to the E2PROM defined in the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces,
manufacturer, and other information.
Additionally, MRV’s SFP+ transceivers provide a enhanced digital diagnostic monitoring interface, which allows real-time access to
device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power
and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when
particular operating parameters are outside of a factory set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X
(A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID
memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification
and the SFP Multi Source Agreement.
The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside
the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL,
Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM
that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bidirectional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation.
The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation.
SFP-10GD-LR transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics.
Digital Diagnostics Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Note
Δ DDTemperature
-
-
3
ºC
-
Δ DDVoltage
-
-
3
%
-
Accuracy
Internally Measured Transceiver Temperature
Internally Measured Transceiver Supply Voltage
Δ DDBias
-
-
10
%
1
Measured TX Output Power
Δ DD Tx-Power
-
-
2
dB
-
Measured RX Received Average Optical Power
Δ DDRx-Power
-
-
2
dB
-
Measured TX Bias Current
Dynamic Range for Rated Accuracy
Internally Measured Transceiver Temperature
Internally Measured Transceiver Supply Voltage
Measured TX Bias Current
DDTemperature
-5
-
70
ºC
-
DDVoltage
3.1
-
3.5
V
-
DDBias
0
-
TBD
mA
-
Measured TX Output Power
DD Tx-Power
-8.2
-
0.5
dBm
-
Measured RX Received Average Optical Power
DD Rx-Power
-14.2
-
0.5
dBm
-
DDTemperature
-40
-
125
ºC
-
DDVoltage
2.8
-
4.0
V
-
DDBias
0
-
20
mA
-
Measured TX Output Power
DD Tx-Power
-10
-
+2
dBm
-
Measured RX Received Average Optical Power
DDRx-Power
-22
-
+2
dBm
-
Max Reporting Range
Internally Measured Transceiver Temperature
Internally Measured Transceiver Supply Voltage
Measured TX Bias Current
Notes:
1.
Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser.
4
Datasheet
Mechanical Dimensions
Mechanical Specifications
MRV’s SFP-10GD-SX SFP+ transceivers are compatible with the SFF-8432 specification for improved pluggable form factor.
Bail color is beige.
Model
Description
Data Rate
Wavelength
(nm)
Bail Latch
Color
Max. Link
Length (km)
Ordering Information
SFP-10GD-LR
SFP+ Transceiver Single-Mode
9.95 - 10.52 Gbps
1310
Blue
0 -10
MRV has more than 50 offices throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com.
Please e-mail us at [email protected] or call us for assistance.
MRV Los Angeles
20415 Nordhoff St.
Chatsworth, CA 91311
800-338-5316
818-773-0900
MRV Boston
295 Foster St.
Littleton, MA 01460
800-338-5316
978-952-4700
MRV International
Business Park Moerfelden
Waldeckerstrasse 13
64546 Moerfelden-Walldorf
Germany
Tel. (49) 6105/2070
Fax (49) 6105/207-100
All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the
accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact MRV Communications for more information.
MRV Communications and the MRV Communications logo are trademarks of MRV Communications, Inc. Other trademarks are the property of their respective holders.
MRV-OP-SFP10GDLR-082708
3020053-001 Rev. A1
Copyright ©2008 MRV Communications, Inc. All Rights Reserved.