SC9827 VCD SIGNAL-CHIP PROCESSOR DESCRIPTION SC9827 is a single chip SOC for CD-G system, it integrates CD servo and correct decoder, Audio DAC. Working with the RF pre- processor of CD composes a low cost and high performance CD-G system solution. FEATURES LQFP-128-14X14-0.4 * Periphery circuit is simple, servo and decoder integrated; * Support CD-G decode play; * Embedded Audio DAC, PWM output; * JPEG decode and play function; * OSD function; * Adopts CD servo arithmetic, strong correct function and good ORDERING INFORMATION coherence. APPLICATION Device Package SC9827 LQFP-128-14x14-0.4 * CD-G system BLOCK DIAGRAM 117 122 105 106 107 102 101 97 93 92 88 86 71 70 62 61 DWE# 123 114 124 125 126 VCOM DRAS0# ADC RBIAS Digital Servo GPIO interface CAS# IDATA RFIN 32-bit RISC Processor SRAM/ROM 8kB High Speed Buffer RFREF MOTO1 Digital 108 Signal Processor TRAY_SW TDM Interface LA19 Oscillator Display Controller Gateway DMA controller Transport Parser LA8 LA7 LA0 XOUT 109 110 111 Serial Audio Interface SLED_SW 16-bit Audio DAC LDON DRAM Interface 2 3 CS3# 6 7 8 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn LD7 LD0 Audio ADC Clock Generator 104 103 112 113 XIN 9 60 59 55 54 43 40 33 31 30 28 21 20 10 13 16 17 18 19 REV:1.0 2009.03.26 Page 1 of 7 SC9827 ABSOLUTE MAXIMUM RATING Symbol Rating Unit Power Supply Voltage Characteristics VDD -0.5 ~ +5.5 V Input Voltage on Pins VIN -0.5 ~VDD + 0.5 V Operating Temperature Topr -20 ~ +75 °C ELECTRICAL CHARACTERISTICS (unless otherwise specified, Tamb=25°C) Characteristics Symbol Test conditions Min. Typ. Max. Unit Operating Voltage VDD 4.5 5 5.5 V Operating Current IDD 48 50 52 mA Quiescent Current IDD(q) VDD=5V; Tamb=25°C -- -- 300 μA Operating Temperature Tamb VDD=5V; Tamb=25°C -10 -- +80 °C (THD+N) /S 0dB 1KHz signal input - -65 - dB No signal input - 75 - dB DA output Distortion DA output Signal to Noise S/N HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.0 2009.03.26 Page 2 of 7 SC9827 DBUS8 DBUS7 DBUS6 DBUS5 DBUS4 DBUS3 DBUS2 DBUS1 DBUS0 MA8 MA7 MA6 MA5 MA4 MA3 85 DBUS9 86 DBUS10 87 DBUS11 88 DBUS13 89 DBUS12 90 DBUS14 91 VCC 92 DBUS15 VSS_P 93 VSS VCC_P 94 RESET# AUX27 95 AUX11 AUX12 96 AUX10 AUX13 PIN CONFIGURATION 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 AUX14 97 64 MA2 VPP2 98 63 MA1 MA0 VCC 99 62 VSS 100 61 DOE#/MA9 AUX00 101 60 DWE# AUX01 102 59 DRAS0# CRIN 103 58 VCC CROUT 104 57 VSS RAD 105 56 VPP FOC 106 55 CAS# SLED 107 54 LA19 MOTO1 108 53 LA18 TRAY_SW 109 52 LA17 SLED_SW 110 51 LA16 LDON 111 50 LA15 ADACL 112 49 LA14 ADACR 113 48 LA13 RBIAS 114 47 LA12 VSSA1 115 46 LA11 VDDA1 116 45 LA10 B 117 44 LA9 A 118 43 LA8 C 119 42 VCC D 120 41 VSS F 121 40 LA7 SC9827 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn 29 30 31 32 VSS 13 XOUT 12 XIN 11 VCC 10 LD7 9 LD6 8 LD5 7 LD4 6 LD3 5 LD2 4 LD1 3 LD0 2 CS3# 1 CSO# LA0 LOE# 33 LWR# 128 AUX07 LA1 VDDA2 AUX06 LA2 34 AUX05 35 127 VSSA 126 VSSA2 AUXO3 RRFEF MIC2 LA3 VDDA 36 VCM 125 COMP LA4 RFIN VREF 37 RSET 124 VSSA LA5 IDATA VCCV LA6 38 YDAC 39 123 VSSV 122 VDAC E VCOM REV:1.0 2009.03.26 Page 3 of 7 SC9827 PIN DESCRIPTION Pin no. Pin name I/O Function 1 VSSV I Analog ground. 2 VDAC O Video DAC V port output. 3 YDAC O Video DAC Y port output. 4 VCCV I Analog power supply. 2.5V 5，12 VSSA I Analog ground. 6 RSET O 7 VREF O 8 COMP O 9 VCM O 10 MIC2 I Microphone input. 11 VDDA I Analog 5.0V power supply. 13 AUX03 I/O General-purpose programmable I/O. 14~16 AUX0[5:7] I/O General-purpose programmable I/O. 17 LWR# O RISC interface writable (low active). 18 LOE# O RISC static memory output (low active). 19 CS0# O Chip select 0 for SRAM. 20 CS3# O Chip select 3 for SRAM. 21~28 LD[0:7] I/O Data bus. VCC I Main power supply 2.5V 30 XIN I 27MHz crystal oscillator input, the duty is 50%. 31 XOUT O Input clock crystal oscillator output. VSS I Main ground. Reset the internal current of generator; connect with a 510Ω resistor to ground. Output reference voltage, connect a 0.01μF high frequency filter capacitor to VSSA. Compensation capacitance for low-pass filter on VDAC. Connect to a 0.01μF high-frequency bypass capacitor to VSSA. ADC analog reference voltage, connect to a 0.01μF high frequency filter capacitor to VSSA. 29 42 58 87 99 32 41 57 89 100 33~40 LA[0:7] O Address bus. 43~54 LA[8:19] O Address bus. 55 CAS# O Column address filter to dynamic memory (low active). 56 VPP I 5V power supply. 59 DRAS0# O Row address filter to dynamic memory. 60 DWE# O Writable dynamic memory (low active). HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.0 2009.03.26 Page 4 of 7 SC9827 Pin no. Pin name I/O 61 DOE#/MA9 O 62~70 71~86 MA[0:8] DBUS[0:15] Function Output data to dynamic memory (low active), Multivariate memory row and column address. O Multivariate memory row and column address. I/O Input/output when Dynamic memory read/write. 88 RESET# I External system reset will make ES3890 reset. 90 VSS_P I PLL system ground. 91 VCC_P I PLL system 2.5V power supply. 92 AUX27 I/O General-purpose programmable I/O. 93~97 AUX1[0:4] I/O General-purpose programmable I/O. 98 VPP2 I 101~102 AUX0[0:1] I/O 103 CRIN I 8M crystal oscillator input of Servo unit. 104 CROUT O 8M crystal oscillator output of Servo unit. 105 RAD O Tracking driver signal. 106 FOC O Focus driver signal. 107 SLED O Sled motor driver signal. 108 MOTO1 O Spindle motor driver signal. 109 TRAY_SW I Tray position monitor signal input. 110 SLED_SW I Sled motor position monitor signal input. 111 LDON O Laser control signal output. 112 ADACL O Audio DAC left channel output. 113 ADACR O Audio DAC right channel output. 114 RBIAS O Internal resistor adjust. 115 VSSA1 I Analog ground 1 for servo unit. 116 VDDA1 I Analog power supply 1 for servo unit. 117 B I Central diode current signal input 1 118 A I Central diode current signal input 2 119 C I Central diode current signal input 3 120 D I Central diode current signal input 4 121 F I Satellite diode current signal input 122 E I Satellite diode current signal input 123 VCOM I DC voltage input pin 124 IDATA I Output feedback current of data signal. 125 RFIN I CD pick up signal input. 126 RFREF I CD pick up signal reference voltage. 127 VSSA2 I Analog ground 2 for servo unit. 128 VDDA2 I Analog power supply 2 for servo unit. 5V power supply. General-purpose programmable I/O. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.0 2009.03.26 Page 5 of 7 SC9827 FUNCTION DESCRIPTON SC9827 is a single chip SOC for CD-G system, it integrates CD servo and correct decoder, Audio DAC. Working with the RF pre-processor of CD composes a low cost and high performance CD-G system solution. CD servo decode module CD servo decoder is the main module of SC9827, it can perform the CD servo and decode function, and support single/double speed switch, compatible with CD/CD-R/CD-RW/CD-G. Audio DAC module This unit is 16 bits audio DAC, output PWM waveform, and connect to low-filter. CD-G decode module This module has CD-G decode functions. TYPICAL APPLICATION CIRCUIT GND GND Spindle , sled and tray motor driver GND GND DA9 RAD DBUS0 FOC SLED MOTO1 LD7 SLED_SW VDDA2 VSSA2 REREF RFIN IDATA VCOM E F D C A B LA19 VDDA1 AGND LD0 TRAY_SW VSSA1 Tray position monitor signal Sled driver position monitor signal DBUS15 SC9827 EEPROM Driver AVCC DRAM ADACL ADACR CRIN CROUT DA0 LA0 RF processor Focus , tracking driver signal HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn Chip REV:1.0 2009.03.26 Page 6 of 7 SC9827 PACKAGE OUTLINE LQFP-128-14x14-0.4 unit: mm 16.0±0.4 1.60MAX 14.0±0.2 0.15±0.05 14.0±0.2 16.0±0.4 0.10±0.05 128 0.25 0.40 0.185 0.60±0.15 1 HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken: • Persons at a work bench should be earthed via a wrist strap. • Equipment cases should be earthed. • All tools used during assembly, including soldering tools and solder baths, must be earthed. • MOS devices should be packed for dispatch in antistatic/conductive containers. Disclaimer: • Silan reserves the right to make changes to the information herein for the improvement of the design and performance without further notice! • All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products • could cause loss of body injury or damage to property. Silan will supply the best possible product for customers! HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http://www.silan.com.cn REV:1.0 2009.03.26 Page 7 of 7