SILAN SC9640P

SC9640P
CD DIGITAL SERVO SIGNAL PROCESSOR WITH MCU (SLAVE MODE)
DESCRIPTION
SC9640P is a SLAVE chip for desktop audio system with low
cost. It has agile functions and good performance with few external
components.
FEATURES
* Compatible with CD/CD-R/CD-RW
* Support CD play /pause
QFP-64-14 x 14-0.8
* Support CD previous track/next track
* Support appointed music play directly
* Support CD skip forward/skip backward
* Support CD single music, and whole disk repeat play display.
* Support CD random play display
* Support program play for 20 music at most
ORDERING INFORMATION
* Support browse play
* Support A->B repeat reading
* Support IDEX index
Device
SC9640P
Package
QFP-64-14X14-0.8
* Support compatible manual and auto control CD tray..
* Compatible with various chips(Free selecting by jumper)
APPLICATIONS
* Desktop CD audio
BLOCK DIAGRAM
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 1 of 10
SC9640P
ABSOLUTE MAXIMUM RATINGS (Tamb=25°C)
Characteristics
Symbol
Ratings
Unit
Supply Voltage
VDD
-0.5 ~ +5.5
V
Input Voltage On Pins
VIN
-0.5 ~VDD + 0.5
V
Operating Temperature
Topr
-20 ~ +75
°C
ELECTRICAL CHARACTERISTICS (VDD=4.5~5.5V;VSS=0V;Tamb=-10~+50°C)
Characteristics
Symbol
Supply Voltage
VDD
Supply Current
IDD
Condition
5V(When CD is working)
Min.
Typ.
Max.
Unit
4.5
5.0
5.5
V
-
50
-
mA
V
RFIN Input Signal
VRFIN
-
1
-
Reference Voltage
VIr
-
0.5VDD
-
Photo-electricity signal bias input
Vcom
-
2.5
-
V
Input Current Of Central Diode B
IDB
0
-
9
μA
Input Current Of Central Diode A
IDA
0
-
9
μA
Input Current Of Central Diode C
IDC
0
-
9
μA
Input Current Of Central Diode D
IDD
0
-
9
μA
Input Current Of Satellite Diode F
IRF
0
-
4.5
μA
Input Current Of Satellite Diode E
IRE
0
-
4.5
μA
Low-level Input Current at Port PA.
IIL(A)
-
10
-
mA
High-level Output Current at Port PA.
IOH(A)
-
5
-
mA
Low-level Input Current at Port PB.
IIL(B)
-
10
-
mA
High-level Output Current at Port PB.
IOH(B)
-
5
-
mA
LDON Low-level Input Current
ILDON
0
-
2
mA
5
-
-
KΩ
0.9
1.1
1.2
V
0
1
-
mA
0
1
-
mA
0
1
-
mA
0
5
10
mA
Load Resistance DAC
RL
Full-Scale DAC Output Voltage
VFS
RAD Output Current
IRAD
FOC Output Current
IFOC
SLED Current
ISLED
MOTO Output Current
IMOTO
Left channel is the same
as the right.
Left channel is the same
as the right.
High level is the same as
the low level.
High level is the same as
the low level.
High level is the same as
the low level.
High level is the same as
the low level.
Low Level Output Driving Voltage
VOLDRIVE1
RAD,FOC,SELD
0
-
0.4
V
High Level Output Driving Voltage
VOHDRIVE1
RAD,FOC,SELD
VDD-0.4
-
VDD
V
-
1.0
V
-
VDD
V
Moto Low Level Output Voltage
VOLmoto
Moto High Level Output Voltage
VOHmoto
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
0
VDD-1
REV:1.0
2009.03.27
Page 2 of 10
SC9640P
Characteristics
RAD, FOC, SLED, MOTO Output 3State Leakage Current
Total harmonic distortion and NoiseTo-Signal Ratio
DA
Filter Attenuation
OSC Frequency
Symbol
Condition
Min.
Typ.
Max.
Unit
IZODRIVE
RAD,FOC,SELD,MOTO
-10
0
+10
μA
60
65
70
dB
0 to 19 kHz
-
-
19 to 20 kHz
1
-
2
dB
24KHz
25
-
-
dB
25 to 35 KHz
40
-
-
dB
35 to 64 KHz
50
-
-
dB
64 to 68 KHz
31
-
-
dB
68KHz
35
-
-
dB
69 to 88KHz
40
-
-
dB
-
MHz
S/N_DA
Filter_DA
Fsystem
-
8.4672
0.001
dB
PIN CONFIGURATIONS
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 3 of 10
SC9640P
PIN DESCRIPTION
Pin No.
Pin Name
I/O
Function description
1
PULL_UP
I
2
9258_MUTE
O
3
MODE_IN
ADI
4
PULL_UP
I
-
5
DIODE_IN
I
Jumper selection input
6
IIC_DAT
I/O
-
OPEN/P0
I
Connect pull-up resistor
9258 mute output
When CD stops, close the 9258 driver
2.5V~3.5V selects as SLAVE mode
Connect pull-up resistor
SLAVE mode IIC data bus
The CD tray opens input pin which is low
7
Remark
active.
This pin is used as the jumper selecting
output at the same time.
Note: manual tray
should be connected to
the ground
The CD tray closes input pin which is low
8
CLOSE
I
9
OPMTR
O
CD tray driver output.
10
CLMTR
O
CD tray driver output.
11
P1
O
active.
This pin is used as the pick up head
selecting output at the same time.
SLAVE mode IIC clock line
12
IIC_CLK/P2
I
This pin is used as the pick up head
selecting output at the same time.
13
MVSS
-
MCU ground
14
MVDD
-
+5V
15
MRST
I
MCU reset, low level reset
16
MTEST
I
MCU test pin
17
NC
-
No connection
18
NC
-
No connection
19
NC
-
No connection
20
NC
-
No connection
21
NC
-
No connection
22
NC
-
No connection
23
NC
-
No connection
24
NC
-
No connection
25
NC
-
No connection
26
NC
-
No connection
27
NC
-
No connection
28
NC
-
No connection
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
Connect to the ground
REV:1.0
2009.03.27
Page 4 of 10
SC9640P
Pin No.
Pin Name
I/O
Function description
29
NC
-
30
P3
O
31
AMP_MUTE
O
Power amplifier mute output, high active
32
VSSP
-
MCU ground
33
VPP
-
Voltage supply of testing module
34
Vddo
-
DAC power supply
35
Vsso
-
DAC ground
36
VREF
O
Internal reference voltage output
37
VOR
O
DAC right channel audio output
38
FILTCR
I
DAC right channel filter capacitor
39
FILTCL
I
DAC left channel filter capacitor
40
VOL
O
DAC left channel audio output
41
RAD
O
Tracking drive output
42
FOC
O
Focus drive output
43
SLED
O
Sled drive output
44
MOTO
O
Spindle drive output
45
VDD
-
Servo Supply Voltage
46
GND
-
Servo Ground, I/O ground
47
V2/SLED_SW
I
Sledge motor position monitor signal input
48
LDON
O
Laser control signal output
49
Vssal
-
Analog Ground of Servo Module ADC.
50
Vdda1
-
51
B
I
Central diode current signal input B
52
A
I
Central diode current signal input A
53
C
I
Central diode current signal input C
54
D
I
Central diode current signal input D
55
F
I
Satellite diode current signal input F
56
E
I
Satellite diode current signal input E
57
VCOM
I
Photo-electricity signal bias input
58
ISLICE
O
Data signal feed-back current output
59
HFIN
I
CD data pick up signal input
60
HFREF
I
Reference signal
61
Vssa2
-
No connection
Connect to the diode to power on auto
play.
No connection
Typical value 0.5 Vdd
Built-in pull up resistor
Analog Supply Voltage of Servo Module
ADC.
Analog ground of Servo module HF and
the PLL.
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
Remark
REV:1.0
2009.03.27
Page 5 of 10
SC9640P
Pin No.
Pin Name
I/O
Function description
62
Vdda2
-
63
CRIN
I
8.4672MHz input
64
CROUT
O
8.4672MHz output
Remark
Analog power supply of Servo module HF
and the PLL.
FUNCTION DESCRIPTION
1. Jumper
Detail function description
Flag
Function description
Pickup selection
P1
P2
Function
0
0
SANYO DA11
0
1
SONY KSS213C、SAMSUNG B31
1
0
Jianghai GM9350H
1
1
Jianghai GM9350
P1(PIN11)/
P2(PIN12)
Auto play selection(Clock CD selection)
P3
P3(PIN30)
Function
0
Stop after power on complete reading the toc
1
Play the first music after power on complete reading the toc
Note: 1 denotes the jumper diode is connected
2. SLAVE agreement description
The agreement format is the same with IIC:
Control command format
STARTÆ55H+ACKÆCOMMAND+ACKÆSTOP;
State information format
STARTÆAAH+ACKÆDATA1+ACK+……+DATAn+ACKÆSTOP;
Agreement description
ACK format: The host will set DATA bus high at the falling edge of CLK, and judge the state of DATA bus at the
rising edge of CLK. Then it will set DATA low if its state is high and exit if its state is low.
Data format: Sending interval of the control command is longer than 30ms; State information must be received
continuously with interval time longer than 50ms.
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 6 of 10
SC9640P
3. Control command
Address
0X55
Parameter
Meanings
0X00
idle Exit directly, no need to response
0X01
Stop
0X02
Play Resume
0X03
Pause
0X04
-
0X05
Next/Up
0X06
Previous/Down
0X07
Fast Forward
0X08
Fast Rewind
0X09
FAST OFF (Cancel fast forward/backward)
0X0A
Random Off
0X0B
Random
0X0C
Repeat Off
0X0D
Repeat 1
0X0E
Repeat All
0X0F
Memory
0X 10
Intro
0X 11
Intro off
0X12
Door in
0X13
Door out
0x14
Door open/close
0X15~0X1F
Unused
OX20~0X2A
0~9
0X2B
+10
0X 2C
Set start point A of repeat reading
0X2E
Cancel repeat reading
0X2F
INDEX++
0X30
INDEX-Open INDEX browse play:
0X31~0X4F
(Play time of each INDEX is from 6S to 30S corresponding to the
commands from 0X31 to 0X4F)
0X50
Stop INDEX browse play
0X51~0X80
Unused
0X 81~0XE3
Play the appointed music(1~99)
Format: BIT7=1; BIT0~6=music no.;
0XE4~0XFF
0X66
0X81~0XE3
Unused
Play the appointed INDEX(1~99)
Format: BIT7=1;BIT0~6=INDEX 号;
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 7 of 10
SC9640P
4. State information
Address
Parameter
0X01(BIT0)
0X01(BIT1)
0X01(BIT2)
0X01(BIT3)
OXAA
0X01(BIT4)
0X01(BIT5)
0X01(BIT6)
0X01(BIT7)
0X02(BIT0)
0X02(BIT1)
0X02(BIT2)
0X02(BIT3)
0X02(BIT4)
OXAA
Meanings
1=Pause
0=Playing
1=Playing
0=Stop
1=repeat
0=no repeat
1=repeat all
0=no repeat all
1=Random
0=no Random
1=Program active
0=Program invalid
1=program mode
0=non program mode
1=Fast forward/backward state
0=Non fast forward/backward state
1=intro
0=no intro
1=CD Door opened
0=CD Door closed
1=toc reading is completed
0=toc reading is not completed
1=err
0= no err
1=nodisc
0=no nodisc
0X02(BIT5)
Unused, reserved as extension
0X02(BIT6)
Unused, reserved as extension
0X02(BIT7)
Unused, reserved as extension
0X03
The BCD stands for the music number
0X04
The BCD stands for M of MSF
0X05
The BCD stands for S of MSF
0X06
The BCD stands for total music number
0X07
The BCD stands for the minute of total time
0X08
The BCD stands for the second of total time
0X09
The BCD stands for current program unit
0X0A
The BCD stands for current program music
0X0B
The BCD stand for current INDEX number
0X0C
Unused
0X0D
Unused
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 8 of 10
SC9640P
APPLICATION CIRCUIT
Optical pickup
Analog audio output
RF Amp
SA9614
Motor Driver
SA9258/
SA9259
Digital Servo Processor +MCU&Audio DAC
8.4672MHz
Servo Control Unit
DSP Decode Unit
And DAC Unit
SC9640P
Microcontroller Unit
QFP-64-14X14-0.8
IIC_DAT
IIC_CLK
MCU
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 9 of 10
SC9640P
PACKAGE OUTLINE
Unit: mm
17.20±0.30
14.00±0.20
0.73~1.03
QFP-64-14X14-0.8
MOS DEVICES OPERATE NOTES:
Electrostatic charges may exist in many things. Please take following preventive measures to prevent effectively
the MOS electric circuit as a result of the damage which is caused by discharge:
z
The operator must put on wrist strap which should be earthed to against electrostatic.
z
Equipment cases should be earthed.
z
All tools used during assembly, including soldering tools and solder baths, must be earthed.
z
MOS devices should be packed in antistatic/conductive containers for transportation.
Disclaimer:
•
Silan reserves the right to make changes to the information herein for the improvement of the design and performance
without further notice!
•
All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products
in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety
standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products
could cause loss of body injury or damage to property.
•
Silan will supply the best possible product for customers!
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http:// www.silan.com.cn
REV:1.0
2009.03.27
Page 10 of 10