CYPRESS CYV15G0101EQ_07

CYV15G0101EQ
Multi Rate Video Cable Equalizer
Features
■
Pb-free and RoHS compliant
■
Uses Cypress CLEANLink™ technology
■
Pin compatible to existing equalizer devices
■
Multi rate adaptive equalization
■
Operates from 143 to 1485 Mbps serial data rate
■
SMPTE 292M, SMPTE 344M, and SMPTE 259M compliant
Functional Description
■
Supports DVB-ASI at 270 Mbps
■
Cable length indicator for HD-SDI and SD-SDI data rates
■
Maximum cable length adjustment for HD-SDI and SD-SDI
data rates
■
Carrier detect and mute functionality for HD-SDI and SD-SDI
data rates
The CYV15G0101EQ is a multi rate adaptive equalizer designed
to equalize and restore signals received over 75Ω coaxial cable.
The equalizer meets SMPTE 292M, SMPTE 344M, and SMPTE
259M data rates. The CYV15G0101EQ is optimized to equalize
up to 350m of Belden 1694A coaxial cable at 270 Mbps and
typically up to 200m of Belden 1694A coaxial cable at 1.485
Gbps. The CYV15G0101EQ connects seamlessly to the
HOTLink II family of transceivers.
■
Equalizer bypass mode
■
Seamless connection with HOTLink II™ family
■
Equalizes up to 350m of Canare L-5CFB and Belden 1694A
coaxial cable at 270 Mbps
■
Typically equalizes up to 200m of Canare L-5CFB and Belden
1694A coaxial cable at 1.485 Gbps
■
Low power: 160 mW at 3.3V
■
Single 3.3V supply
The CYV15G0101EQ has DC restoration to compensate for the
DC content of the SMPTE pathological patterns. A cable length
indicator (CLI) provides an indication of the cable length being
equalized at HD-SDI and SD-SDI data rates. The maximum
cable length adjust (MCLADJ) sets the approximate maximum
cable length to equalize at SD and HD data rates. The
CYV15G0101EQ’s differential serial outputs (SDO, SDO) mute
when the approximate cable length set by MCLADJ is reached.
CD/MUTE is a bidirectional pin that provides an indication of the
signal present at the equalizer inputs. It also controls muting the
outputs of the equalizer at HD and SD data rates.
■
16-pin SOIC
Power consumption is typically 160 mW at 3.3V.
■
0.18 μm CMOS technology
Equalizer System Connection Diagram
HOTLink II
Serializer
Cypress Semiconductor Corporation
Document Number: 001-04184 Rev. *E
CYV15G0101EQ
Multi Rate
Cable
Equalizer
Serial Links
Cable
Driver
Copper Cable
Connections
•
198 Champion Court
•
HOTLink II
Deserializer
San Jose, CA 95134-1709
•
408-943-2600
Revised October 25, 2007
[+] Feedback
CYV15G0101EQ
Equalizer Block Diagram
CYV15G0101EQ Multi-Rate Video Cable Equalizer Block Diagram
CYV15G0101EQ Multi-Rate Video Cable Equalizer Block Diagram
MCLADJ
Cable Length Analog
Adjustor and Mute
Threshold Block
Carrier Detect and
Mute Control Block
MUTE
CD
DC Restore
BYPASS
SDI, SDI
Equalizer
Differential Output
SDO, SDO
Pinouts
Figure 1. Pin Diagram - 16 Pin SOIC (Top View)
CLI
16
CD/MUTE
VCC
2
15
VCC
GND
3
14
GND
SDI
4
13
SDO
CYV15G0101EQ
Document Number: 001-04184 Rev. *E
SDI
5
12
SDO
GND
6
11
GND
AGC+
7
10
MCLADJ
AGC-
8
9
BYPASS
Page 2 of 10
[+] Feedback
CYV15G0101EQ
Table 1. Pin Descriptions - CYV15G0101EQ Single Channel Cable Equalizer
Name
IO Characteristics Signal Description
Control Signals
CLI
Analog Output
Cable Length Indicator. CLI provides an analog voltage proportional to the equalized cable
length. CLI works at both SD-SDI and HD-SDI data rates.
CD/MUTE
LVTTL IO
Carrier Detect or Mute Indicator.
Output:
When the incoming data stream is present and the cable length does not exceed that set by
MCLADJ, the CD/MUTE outputs a voltage less than 0.8V.
When the incoming data stream is not present or the cable length exceeds that set by
MCLADJ, the CD/MUTE outputs a voltage greater than 2.8V.
Input:
When the CD/MUTE pin is set LOW, the equalizer’s differential serial outputs are not muted.
When the CD/MUTE pin is set HIGH, the equalizer’s differential serial outputs are muted.
MCLADJ
Analog Input
Maximum Cable Length Adjust. The maximum equalized cable length is set by the voltage
applied to the MCLADJ input. When the maximum cable length set by MCLADJ is reached,
CD is driven high and the differential output is muted.
If MCLADJ functionality is not needed, this pin should be left floating or tied to ground to
allow maximum equalized cable length.
MCLADJ works at both SD and HD data rates.
BYPASS
LVTTL Input
Equalizer Bypass. When BYPASS is set HIGH, the signal presented at the equalizer’s
differential serial inputs (SDI, SDI) is routed to the equalizer’s differential serial outputs
(SDO, SDO) without performing equalization.
When BYPASS is set LOW, the incoming video data stream is equalized and presented at
the equalizer‘s serial differential outputs (SDO, SDO).
In equalizer bypass mode, CD/MUTE is not functional.
AGC±
Analog
Automatic Gain Control. Place a capacitor of 1 μF between the AGC± pins.
SDO, SDO
Differential
Output
Differential Serial Outputs. The equalized serial video data stream is presented at the
SDO/SDO differential serial CML output.
SDI, SDI
Differential
Input
Differential Serial Inputs. SDI/SDI accepts either a single-ended or differential serial video
data stream over 75Ω coaxial cable.
VCC
Power
+3.3V Power.
GND
Gnd
Connect to Ground.
Power
Document Number: 001-04184 Rev. *E
Page 3 of 10
[+] Feedback
CYV15G0101EQ
Equalizer Operation
MCLADJ
The CYV15G0101EQ is a high speed adaptive cable equalizer
designed to equalize standard definition (SD) and high definition
(HD) serial digital interface (SDI) video data streams.
CYV15G0101EQ equalizer is optimized to equalize up to 350m
of Canare L-5CFB and Belden 1694A cable at 270 Mbps and
typically up to 200m of Canare L-5CFB and Belden 1694A cable
at 1.485 Gbps. The CYV15G0101EQ equalizer contains one
power supply and typically consumes 160 mW power at 3.3V.
The multi rate equalizer meets the SMPTE 259M, SMPTE 292M,
SMPTE 344M, and DVB-ASI video standards. It meets all pathological requirements for SMPTE 292M as defined by RP198, and
for SMPTE 259M as defined by RP178. The CYV15G0101EQ
multi rate cable equalizer is auto adaptive from 143 Mbps to
1.485 Gbps.
Maximum Cable Length Adjust (MCLADJ) sets the approximate
maximum amount of cable to be equalized. When the maximum
cable length set by MCLADJ is reached, CD is driven high and
the outputs are muted. MCLADJ works at SD and HD data rates.
The CYV15G0101EQ equalizer has variable gain and multiple
equalization stages that reverse the effects of the cable. This
equalization is achieved by separate regulation of the lower and
higher frequency components in the signal to give a clean output
eye diagram. The CYV15G0101EQ has DC restoration to
compensate for the DC content of the SMPTE pathological
patterns.
SDI, SDI
The CYV15G0101EQ accepts single-ended or differential serial
video data streams over 75Ω coaxial cable. It is recommended
to AC couple the SDI and SDI inputs as they are internally biased
to 1.2V.
SDO, SDO
The CYV15G0101EQ has differential serial output interface
drivers that use current mode logic (CML) drivers to provide
source matching for the transmission line. These outputs are
either AC coupled or DC coupled to the HOTLink II SerDes
device.
CLI
Cable Length Indicator (CLI) is an analog output that gives an
output voltage proportional to the equalized cable length. CLI
gives an approximation of the length of cable at the differential
serial inputs (SDI, SDI). CLI works at high definition (HD) data
rates and standard definition (SD) data rates. The graph in
Figure 3 on page 7 illustrates the CLI output voltage at various
Belden 1694A cable lengths. With an increase in cable length,
CLI output voltage decreases.
Document Number: 001-04184 Rev. *E
The graph in Figure 2 on page 7 illustrates the voltage required
at MCLADJ input to equalize various Belden 1694A cable
lengths for SD and HD data rates. If MCLADJ functionality is not
needed, this pin should be left floating or tied to ground to allow
maximum equalized cable length.
CD/MUTE
Carrier Detect/MUTE (CD/MUTE) is a bidirectional pin that
provides an indication of the signal present at the equalizer’s
input, or it controls the muting of the equalizer’s output. The
(CD/MUTE) operates for both HD and SD data rates.
If CD/MUTE is used as an output and the incoming data stream
is not present or the cable length exceeds that set by MCLADJ,
the voltage at the CD/MUTE output is greater than 2.8V. If
CD/MUTE is used as an output, the incoming data stream is
present and the cable length does not exceed that set by
MCLADJ, then the voltage at the CD/MUTE output is less than
0.8V.
If CD/MUTE is used as an input and is set LOW, the equalizer
serial outputs are not muted. If the CD/MUTE is used as an input
and is set HIGH, then the equalizer serial outputs are muted.
When an invalid signal or a signal transmitted with a launch
amplitude of less than 500 mV at HD data rates is received, the
equalizer’s serial outputs are muted.
BYPASS
The CYV15G0101EQ has a bypass mode that allows the user to
bypass the equalizer’s equalization and DC restoration
functions. When the bypass mode is set HIGH, the signal
presented at the equalizer’s differential serial inputs (SDI, SDI)
is routed to the equalizer’s differential serial outputs (SDO, SDO)
without equalizing.
When BYPASS is set LOW, the incoming video data stream is
equalized and presented at the equalizer‘s differential serial
outputs (SDO, SDO).
In equalizer bypass mode, CD/MUTE is not functional.
AGC
Place a capacitor of 1 μF between the AGC± pins of the
CYV15G0101EQ equalizer.
Page 4 of 10
[+] Feedback
CYV15G0101EQ
Maximum Ratings
Power Up Requirements
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
The CYV15G0101EQ contains one power supply. The voltage
on any input or IO pin must not exceed the power pin during
power up.
Storage Temperature .................................. –65°C to +150°C
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Operating Range
Supply Voltage to Ground Potential................–0.5V to +3.8V
Range
Ambient
Temperature
VCC
DC Voltage Applied to Outputs
in High Z State ....................................... –0.5V to VCC + 0.5V
Commercial
0°C to +70°C
+3.3V ±5%
DC Input Voltage ..................................... –0.5V to VCC+0.5V
Electro Static Discharge (ESD) HBM....................... > 2000 V
(JEDEC EIA/JESD-A114A)
Latch Up Current .................................................... > 200 mA
DC Electrical Characteristics
Parameter
Description
Min
Typ
Max
Unit
–
3.135
3.3
3.465
V
–
125
160
190
mW
–
38
48
60
mA
Load = 50Ω
–
VCC –
ΔVSDO/2 = 2.9
–
V
Input Common Mode Voltage[1]
(Bypass = High)
–
1
1.4
V
Input Common Mode Voltage[1]
(Bypass = Low)
–
0
2.9
V
CLI DC Voltage (0m)[1]
–
2.2
2.65
2.95
V
–
1.5
1.9
2.3
V
–
0.4
0.72
1.02
V
Carrier Not Present
2.8
–
–
V
–
–
0.8
V
2.5
–
–
V
–
–
1
V
Supply
Voltage[1]
Power
Consumption[2]
IS
Supply
Current[1]
VCMOUT
Output Common Mode Voltage[1]
VCMIN
VCC
PD
–
–
CLI DC Voltage (No
Signal)[1]
–
Floating MCLADJ DC
–
MCLADJ Range[3]
VCD/MUTE(OH) CD/MUTE Output
Voltage[1]
Voltage[1]
VCD/MUTE(OL)
Test Conditions
–
Carrier Present
VCD/MUTE
CD/MUTE Input Voltage Required to Min to Mute
Force Outputs to Mute[1]
VCD/MUTE
CD/MUTE Input Voltage Required to Max to Activate
Force Active[1]
1.3
V
Notes
1. Production test.
2. Calculated results from production test.
3. Not tested. Based on characterization.
Document Number: 001-04184 Rev. *E
Page 5 of 10
[+] Feedback
CYV15G0101EQ
AC Electrical Characteristics
Parameter
Description
Test Conditions
[1]
Min
Typ
Max
Unit
–
–
Serial Input Data Rate
–
143
1485
Mbps
VSDI
Input Voltage Swing
Single-ended, at the transmitter,
HD data rate
500[5]
1200
mV
VSDI
Input Voltage Swing
Single-ended, at the transmitter,
SD data rate
500[6]
1200
mV
ΔVSDO
Output Voltage Swing[1]
Differentialp-p, 50Ω load
950
mV
–
Output Jitter for Various Cable
Lengths and Data Rates
450
700
[1]
270 Mbps
Belden 1694A: 0-350m
Canare L-5CFB: 0-350m
800 mV transmit amplitude
Equalizer pathological pattern
–
0.2
–
UI
1.485 Gbps
Belden 1694A: 0-140m
Canare L-5CFB: 0-140m
800 mV transmit amplitude
Equalizer pathological pattern
–
0.25[1]
–
UI
1.485 Gbps
Belden 1694A: 140-200m
Canare L-5CFB: 140-200m
800 mV transmit amplitude
Equalizer pathological pattern
–
0.3[7]
–
UI
–
Output Rise/Fall Time[3, 4]
20% - 80%, HD data rate
80
120
220
ps
–
Output Rise/Fall
Time[3, 4]
20% - 80%, SD data rate
80
120
350
ps
–
Mismatch in Rise/Fall Time[3, 4]
–
–
30
ps
–
20
–
ps
–
–
–
10
%
–
Distortion[3, 4]
–
Duty Cycle
–
Overshoot[3, 4]
–
HD color bar pattern
Loss[3]
–
Input Return
-15
–
–
dB
–
Input Resistance[3, 4]
Single-ended
–
2.5
–
kΩ
–
Input Capacitance[3, 4]
Single-ended
–
1
–
pF
–
[3, 4]
Single-ended
–
50
–
Ω
Output Resistance
Notes
4. Not tested. Guaranteed by design simulations.
5. Based on characterization across temperature and voltage with 140m of Belden 1694A cable, transmitting SMPTE Equalizer Pathological Test Pattern.
6. Based on characterization across temperature and voltage with 350m of Belden 1694A cable, transmitting SMPTE Equalizer Pathological Test Pattern.
7. Based on characterization at TA = 25°C, VCC = 3.3V
Document Number: 001-04184 Rev. *E
Page 6 of 10
[+] Feedback
CYV15G0101EQ
Typical Performance Graphs
(Unless otherwise stated, VCC = 3.3V, TA = 25°C)
Figure 2. MCLADJ Input Voltage vs. Belden 1694A Cable Length at SD-SDI and HD-SDI Data Rates
2.7
2.6
2.5
VOLTAGE (V)
2.4
2.3
2.2
2.1
2
1.9
1.8
1.7
0
50
100
150
200
250
300
350
C A B LE LE N G T H (m )
Figure 3. CLI Output Voltage vs. Belden 1694A Cable Length at SD-SDI and HD-SDI Data Rates
2 .7
2 .6
2 .5
VOLTAGE (V)
2 .4
2 .3
2 .2
2 .1
2
1 .9
1 .8
1 .7
0
50
1 00
15 0
2 00
25 0
300
3 50
C A B L E L E N G T H (m )
Document Number: 001-04184 Rev. *E
Page 7 of 10
[+] Feedback
CYV15G0101EQ
Typical Application Circuit
Figure 4. Interfacing CYV15G0101EQ to the HOTLink II SerDes
C D / MU T E
CL I
+3.3V
+3.3V
C12
LFI
RXD7
RXD6
RXD5
RXD4
RXD3
RXD2
RXD1
RXD0
RXOP
RXST2
RXST1
RXST0
RXCLK+
RXCLK−
RXCLKC+
RXLE
SDASEL
LPEN
INSEL
IN1+
0.01 μF
16
15
14
13
12
11
10
9
Z0
2 Z0
IN1−
FRAMCHAR
RFEN
RFMODE
DECMODE
RXCKSEL
RXMODE
RXRATE
0. 01 μF
C10
R18
Z0
CD/MUTE
CLI
VCC
VCC
VEE
VEE
SDO
SDI
SDO
SDI
VEE
VEE
MCLADJ AGC+
BYPASS AGC−
1
2
3
4
5
6
7
8
CYV15G0101EQ
C15
1 μF
R16
75 Ω
C16
1 μF
BNC JACK
75Ω
L2
6.4 n H
+
1 μF
C11
37.4 Ω
R15
75 Ω
R14
MC L A D J
CYV15G0101DXB
Document Number: 001-04184 Rev. *E
Page 8 of 10
[+] Feedback
CYV15G0101EQ
Ordering Information
Ordering Code
Package Name
CYV15G0101EQ-SXC
SZ16.15
Operating
Range
Package Type
Pb-free 16-Pin 150 Mil SOIC
0 to 70°C
Package Dimension
Figure 5. 16-Pin (150 Mil) SOIC S16.15
0).)$
$)-%.3)/.3).).#(%3;--=-).
-!8
2%&%2%.#%*%$%#-3
0!#+!'%7%)'(4GMS
;=
;=
;=
;=
0!24
334!.$!2$0+'
3:,%!$&2%%0+'
;=
;=
;=
;=
3%!4).'0,!.%
8²
;=
;=
;=
;=
"3#
;=
;=
²^²
;=
;=
;=
;=
;=
;=
51-85068-*B
Document Number: 001-04184 Rev. *E
Page 9 of 10
[+] Feedback
CYV15G0101EQ
Document History Page
Document Title: CYV15G0101EQ Multi Rate Video Cable Equalizer
Document Number: 001-04184
REV.
ECN NO.
ISSUE
DATE
ORIG. OF
CHANGE
**
389196
SEE ECN
BCD
New preliminary datasheet
*A
394763
SEE ECN
BCD
Updated preliminary datasheet for release to the internet
*B
431556
SEE ECN
BCD
Changed AC and DC parameters
*C
504487
SEE ECN
FRE
Updated AC and DC parameters. Changed datasheet status from
preliminary to final
*D
514998
SEE ECN
FRE
*E
1396423
SEE ECN
UKK/AESA
DESCRIPTION OF CHANGE
Fixed typo in diagrams on page 2
Updated AC and DC electrical characteristics and pin description of
MCLADJ and CD.
© Cypress Semiconductor Corporation, 2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-04184 Rev. *E
Revised October 25, 2007
Page 10 of 10
PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered
trademarks referenced herein are property of the respective corporations. Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the
Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. HOTLink II is a trademark of Cypress
Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations. All products and company names mentioned in this document may
be the trademarks of their respective holders.
[+] Feedback