CYPRESS CY7C1334H

CY7C1334H
2-Mbit (64K x 32) Pipelined SRAM with
NoBL™ Architecture
Functional Description[1]
Features
• Pin compatible and functionally equivalent to ZBT™
devices
• Internally self-timed output buffer control to eliminate
the need to use OE
• Byte Write capability
• 64K x 32 common I/O architecture
• 3.3V core power supply
• 3.3V/2.5V I/O operation
• Fast clock-to-output times
— 3.5 ns (for 166-MHz device)
— 4.0 ns (for 133-MHz device)
• Clock Enable (CEN) pin to suspend operation
• Synchronous self-timed write
• Asynchronous output enable (OE)
• Offered in Lead-Free JEDEC-standard 100-pin TQFP
package
• Burst Capability—linear or interleaved burst order
• “ZZ” Sleep mode option
The CY7C1334H is a 3.3V/2.5V, 64K x 32
synchronous-pipelined Burst SRAM designed specifically to
support unlimited true back-to-back Read/Write operations
without the insertion of wait states. The CY7C1334H is
equipped with the advanced No Bus Latency™ (NoBL™) logic
required to enable consecutive Read/Write operations with
data being transferred on every clock cycle. This feature
dramatically improves the throughput of the SRAM, especially
in systems that require frequent Write/Read transitions.
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock. The
clock input is qualified by the Clock Enable (CEN) signal,
which, when deasserted, suspends operation and extends the
previous clock cycle. Maximum access delay from the clock
rise is 3.5 ns (166-MHz device)
Write operations are controlled by the four Byte Write Select
(BW[A:D]) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. In order to avoid bus
contention, the output drivers are synchronously tri-stated
during the data portion of a write sequence.
Logic Block Diagram
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
BWA
BWB
BWC
BWD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
ZZ
E
O
U
T
P
U
T
D
A
T
A
S
T
E
E
R
I
N
G
INPUT
REGISTER 0
B
U
F
F
E
R
S
DQs
E
E
READ LOGIC
SLEEP
CONTROL
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05678 Rev. *B
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 6, 2006
[+] Feedback
CY7C1334H
.
Selection Guide
166 MHz
133 MHz
Unit
Maximum Access Time (tCO)
3.5
4.0
ns
Maximum Operating Current (IDD)
240
225
mA
Maximum CMOS Standby Current
40
40
mA
Pin Configuration
VSS
CLK
WE
CEN
OE
ADV/LD
91
90
89
88
87
86
85
A
VDD
92
A
CE3
93
81
BWA
94
82
BWB
95
83
BWC
96
NC/18M
BWD
97
NC/9M
CE2
98
84
A
CE1
99
A
1
80
NC
2
79
DQB
DQC
3
78
DQB
VDDQ
4
77
VDDQ
VSSQ
5
76
VSSQ
DQC
6
75
DQB
DQC
7
74
DQB
DQC
8
73
DQB
DQC
9
72
DQB
VSSQ
10
71
VSSQ
VDDQ
11
70
VDDQ
DQC
12
69
DQB
DQC
13
68
DQB
NC
14
67
VSS
VDD
15
66
NC
NC
16
65
VSS
17
64
VDD
ZZ
DQD
18
63
DQA
DQD
19
62
DQA
VDDQ
20
61
VDDQ
VSSQ
21
60
VSSQ
DQD
22
59
DQA
DQD
23
58
DQA
DQD
24
57
DQA
CY7C1334H
41
42
43
44
45
46
47
48
49
50
VDD
NC/72M
NC/36M
A
A
A
A
A
A
NC/4M
MODE
Document #: 38-05678 Rev. *B
40
NC
39
51
VSS
30
NC/144M
DQA
NC
NC/288M
52
38
29
37
DQA
DQD
A0
53
36
28
A1
VDDQ
DQD
A
54
35
27
34
VSSQ
VDDQ
A
DQA
55
33
56
26
32
25
A
DQD
VSSQ
31
BYTE D
NC
DQC
A
BYTE C
100
100-Pin TQFP Pinout
BYTE B
BYTE A
Page 2 of 13
[+] Feedback
CY7C1334H
Pin Definitions
Name
I/O
Description
A0, A1, A
InputSynchronous
Address Inputs used to select one of the 64K address locations. Sampled at the rising edge
of the CLK. A[1:0] are fed to the two-bit burst counter.
BW[A:D]
InputSynchronous
Byte Write Inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled
on the rising edge of CLK.
WE
InputSynchronous
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW.
This signal must be asserted LOW to initiate a Write sequence.
ADV/LD
InputSynchronous
Advance/Load Input. Used to advance the on-chip address counter or load a new address.
When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a
new address can be loaded into the device for an access. After being deselected, ADV/LD
should be driven LOW in order to load a new address.
CLK
Input-Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
CE1
InputSynchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE2 and CE3 to select/deselect the device.
CE2
InputSynchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select/deselect the device.
CE3
InputSynchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE2 to select/deselect the device.
OE
InputAsynchronous
Output Enable, asynchronous input, active LOW. Combined with the synchronous logic
block inside the device to control the direction of the I/O pins. When LOW, the I/O pins are
allowed to behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input
data pins. OE is masked during the data portion of a write sequence, during the first clock when
emerging from a deselected state, when the device has been deselected.
CEN
InputSynchronous
Clock Enable Input, active LOW. When asserted LOW the Clock signal is recognized by the
SRAM. When deasserted HIGH the Clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
ZZ
InputAsynchronous
ZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep”
condition with data integrity preserved. During normal operation, this pin can be connected to
VSS or left floating.
DQs
I/OSynchronous
Bidirectional Data I/O Lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by A[16:0] during the clock rise of the read cycle. The direction of the pins is controlled
by OE and the internal control logic. When OE is asserted LOW, the pins can behave as outputs.
When HIGH, DQs are placed in a tri-state condition. The outputs are automatically tri-stated
during the data portion of a write sequence, during the first clock when emerging from a
deselected state, and when the device is deselected, regardless of the state of OE.
Input
Strap pin
Mode Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence.
MODE
VDD
VDDQ
VSS
VSSQ
Power Supply
I/O Power
Supply
Ground
I/O Ground
NC
Document #: 38-05678 Rev. *B
Power supply inputs to the core of the device.
Power supply for the I/O circuitry.
Ground for the device.
Ground for the I/O circuitry. Should be connected to the ground of the system
No Connects. Not internally connected to the die. 4M, 9M,18M, 72M, 144M, 288M, 576M and
1G are address expansion pins and are not internally connected to the die.
Page 3 of 13
[+] Feedback
CY7C1334H
Functional Overview
The CY7C1334H is a synchronous-pipelined Burst SRAM
designed specifically to eliminate wait states during
Write/Read transitions. All synchronous inputs pass through
input registers controlled by the rising edge of the clock. The
clock signal is qualified with the Clock Enable input signal
(CEN). If CEN is HIGH, the clock signal is not recognized and
all internal states are maintained. All synchronous operations
are qualified with CEN. All data outputs pass through output
registers controlled by the rising edge of the clock. Maximum
access delay from the clock rise (tCO) is 3.5 ns (166-MHz
device).
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If Clock
Enable (CEN) is active LOW and ADV/LD is asserted LOW,
the address presented to the device will be latched. The
access can either be a Read or Write operation, depending on
the status of the Write Enable (WE). BW[A:D] can be used to
conduct Byte Write operations.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion.
All operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD should be driven LOW once the device has been
deselected in order to load a new address for the next
operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, (3) the Write Enable input
signal WE is deasserted HIGH, and (4) ADV/LD is asserted
LOW. The address presented to the address inputs is latched
into the Address Register and presented to the memory core
and control logic. The control logic determines that a read
access is in progress and allows the requested data to
propagate to the input of the output register. At the rising edge
of the next clock the requested data is allowed to propagate
through the output register and onto the data bus, provided OE
is active LOW. After the first clock of the read access the output
buffers are controlled by OE and the internal control logic. OE
must be driven LOW in order for the device to drive out the
requested data. During the second clock, a subsequent
operation (Read/Write/Deselect) can be initiated. Deselecting
the device is also pipelined. Therefore, when the SRAM is
deselected at clock rise by one of the chip enable signals, its
output will tri-state following the next clock rise.
Burst Read Accesses
The CY7C1334H has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to
four Reads without reasserting the address inputs. ADV/LD
must be driven LOW in order to load a new address into the
SRAM, as described in the Single Read Access section above.
The sequence of the burst counter is determined by the MODE
input signal. A LOW input on MODE selects a linear burst
mode, a HIGH selects an interleaved burst sequence. Both
burst counters use A0 and A1 in the burst sequence, and will
wrap around when incremented sufficiently. A HIGH input on
ADV/LD will increment the internal burst counter regardless of
Document #: 38-05678 Rev. *B
the state of Chip Enables inputs or WE. WE is latched at the
beginning of a burst cycle. Therefore, the type of access (Read
or Write) is maintained throughout the burst sequence.
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the write signal WE
is asserted LOW. The address presented to the address inputs
is loaded into the Address Register. The write signals are
latched into the Control Logic block.
On the subsequent clock rise the data lines are automatically
tri-stated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQs and
DQP[A:D]. In addition, the address for the subsequent access
(Read/Write/Deselect) is latched into the Address Register
(provided the appropriate control signals are asserted).
On the next clock rise the data presented to DQs (or a subset
for Byte Write operations, see Write Cycle Description table for
details) inputs is latched into the device and the write is
complete.
The data written during the Write operation is controlled by
BW[A:D] signals. The CY7C1334H provides Byte Write
capability that is described in the Write Cycle Description table.
Asserting the Write Enable input (WE) with the selected Byte
Write Select (BW[A:D]) input will selectively write to only the
desired bytes. Bytes not selected during a Byte Write
operation will remain unaltered. A synchronous self-timed
write mechanism has been provided to simplify the Write
operations. Byte write capability has been included in order to
greatly simplify Read/Modify/Write sequences, which can be
reduced to simple Byte Write operations.
Because the CY7C1334H is a common I/O device, data
should not be driven into the device while the outputs are
active. The Output Enable (OE) can be deasserted HIGH
before presenting data to the DQs. Doing so will tri-state the
output drivers. As a safety precaution, DQs are automatically
tri-stated during the data portion of a Write cycle, regardless of
the state of OE.
Burst Write Accesses
The CY7C1334H has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to
four Write operations without reasserting the address inputs.
ADV/LD must be driven LOW in order to load the initial
address, as described in the Single Write Access section
above. When ADV/LD is driven HIGH on the subsequent clock
rise, the Chip Enables (CE1, CE2, and CE3) and WE inputs are
ignored and the burst counter is incremented. The correct
BW[A:D] inputs must be driven in each cycle of the burst write
in order to write the correct bytes of data.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, and CE3, must remain inactive
for the duration of tZZREC after the ZZ input returns LOW.
Page 4 of 13
[+] Feedback
CY7C1334H
Linear Burst Address Table (MODE = GND)
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Cycle Description Truth Table[2, 3, 4, 5, 6, 7, 8]
Operation
Address
Used
CE
ZZ
ADV/LD
WE
BWx
OE
CEN
CLK
DQ
Deselect Cycle
None
H
L
L
X
X
X
L
L-H
Tri-State
Continue Deselect Cycle
None
X
L
H
X
X
X
L
L-H
Tri-State
Read Cycle (Begin Burst)
External
L
L
L
H
X
L
L
L-H
Data Out (Q)
Read Cycle (Continue Burst)
Next
X
L
H
X
X
L
L
L-H
Data Out (Q)
NOP/Dummy Read (Begin Burst)
External
L
L
L
H
X
H
L
L-H
Tri-State
Dummy Read (Continue Burst)
Next
X
L
H
X
X
H
L
L-H
Tri-State
Write Cycle (Begin Burst)
External
L
L
L
L
L
X
L
L-H
Data In (D)
Write Cycle (Continue Burst)
Next
X
L
H
X
L
X
L
L-H
Data In (D)
NOP/WRITE ABORT (Begin Burst) None
L
L
L
L
H
X
L
L-H
Tri-State
WRITE ABORT (Continue Burst)
Next
X
L
H
X
H
X
L
L-H
Tri-State
IGNORE CLOCK EDGE (Stall)
Current
X
L
X
X
X
X
H
L-H
-
Sleep MODE
None
X
H
X
X
X
X
X
X
Tri-State
Notes:
2. X = “Don't Care.” H = HIGH, L = LOW. CE stands for ALL Chip Enables active. BWx = 0 signifies at least one Byte Write Select is active, BWx = Valid signifies
that the desired Byte Write Selects are asserted, see Write Cycle Description table for details.
3. Write is defined by BW[A:D], and WE. See Write Cycle Descriptions table.
4. When a write cycle is detected, all I/Os are three-stated, even during byte writes.
5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
6. CEN = H, inserts wait states.
7. Device will power-up deselected and the I/Os in a three-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP[A:D] = Tri-State when
OE is inactive or when the device is deselected, and DQs = data when OE is active.
Document #: 38-05678 Rev. *B
Page 5 of 13
[+] Feedback
CY7C1334H
Write Cycle Description[2, 3]
Function
WE
BWD
BWC
BWB
BWA
Read
H
X
X
X
X
Write − No bytes written
L
H
H
H
H
Write Byte A − (DQA)
L
H
H
H
L
Write Byte B − (DQB)
L
H
H
L
H
Write Bytes A, B
L
H
H
L
L
Write Byte C − (DQC)
L
H
L
H
H
Write Bytes C,A
L
H
L
H
L
Write Bytes C, B
L
H
L
L
H
Write Bytes C, B, A
L
H
L
L
L
Write Byte D − (DQD)
L
L
H
H
H
Write Bytes D, A
L
L
H
H
L
Write Bytes D, B
L
L
H
L
H
Write Bytes D, B, A
L
L
H
L
L
Write Bytes D, C
L
L
L
H
H
Write Bytes D, C, A
L
L
L
H
L
Write Bytes D, C, B
L
L
L
L
H
Write All Bytes
L
L
L
L
L
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
IDDZZ
Sleep mode standby current
ZZ > VDD − 0.2V
tZZS
Device operation to ZZ
ZZ > VDD − 0.2V
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ Active to sleep current
This parameter is sampled
tRZZI
ZZ inactive to exit sleep current
This parameter is sampled
Document #: 38-05678 Rev. *B
Min.
Max.
Unit
40
mA
2tCYC
ns
2tCYC
ns
2tCYC
0
ns
ns
Page 6 of 13
[+] Feedback
CY7C1334H
DC Input Voltage ....................................... −0.5V to VDD + 0.5V
Maximum Rating
(Above which the useful life may be impaired. For user guidelines not tested.)
Storage Temperature ..................................... −65°C to +150°C
Ambient Temperature with
Power Applied.................................................. −55°C to +125°C
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current.................................................... > 200 mA
Operating Range
Supply Voltage on VDD Relative to GND.........−0.5V to +4.6V
Supply Voltage on VDDQ Relative to GND .......−0.5V to +VDD
DC Voltage Applied to Outputs
in Tri-State ................................................−0.5V to VDDQ + 0.5V
Range
Com’l
Ambient
Temperature (TA)
0°C to +70°C
Ind’l
–40°C to +85°C
VDD
VDDQ
3.3V - 5%/+10% 2.5V - 5% to
VDD
Electrical Characteristics Over the Operating Range[9, 10]
Parameter
Description
Test Conditions
Min.
VDD
Power Supply Voltage
VDDQ
I/O Supply Voltage
VOH
Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage[9]
VIL
Input LOW Voltage[9]
IX
Input Leakage Current
except ZZ and MODE
GND ≤ VI ≤ VDDQ
Input Current of MODE
Input = VSS
−30
3.135
3.6
V
3.135
VDD
V
for 2.5V I/O
2.375
2.625
V
for 3.3V I/O, IOH = –4.0 mA
2.4
for 2.5V I/O, IOH = –1.0 mA
2.0
for 3.3V I/O, IOL = 8.0 mA
V
0.4
for 3.3V I/O
2.0
VDD + 0.3V
for 2.5V I/O
1.7
VDD + 0.3V
for 3.3V I/O
–0.3
0.8
for 2.5V I/O
–0.3
0.7
–5
5
V
V
µA
µA
5
−5
Input = VSS
µA
µA
30
µA
5
µA
6-ns cycle, 166 MHz
240
mA
7.5-ns cycle, 133 MHz
225
mA
VDD = Max, Device
Deselected,
VIN ≥ VIH or VIN ≤ VIL
f = fMAX = 1/tCYC
6-ns cycle, 166 MHz
100
mA
7.5-ns cycle, 133 MHz
90
mA
Automatic CE
Power-Down
Current—CMOS Inputs
VDD = Max, Device
Deselected, VIN ≤ 0.3V or
VIN > VDDQ – 0.3V, f = 0
All speeds
40
mA
Automatic CE
Power-Down
Current—CMOS Inputs
VDD = Max, Device
Deselected, or VIN ≤ 0.3V or
VIN > VDDQ – 0.3V
f = fMAX = 1/tCYC
6-ns cycle, 166 MHz
85
mA
7.5-ns cycle, 133 MHz
75
mA
Automatic CE
Power-Down
Current—TTL Inputs
VDD = Max, Device
Deselected,
VIN ≥ VIH or VIN ≤ VIL, f = 0
All Speeds
45
mA
Input = VDD
IOZ
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
IDD
VDD Operating Supply
Current
VDD = Max., IOUT = 0 mA,
f = fMAX = 1/tCYC
Automatic CE
Power-Down
Current—TTL Inputs
ISB2
ISB3
ISB4
V
0.4
Input = VDD
ISB1
Unit
for 3.3V I/O
for 2.5V I/O, IOL = 1.0 mA
Input Current of ZZ
Max.
−5
Notes:
9. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC)> –2V (Pulse width less than tCYC/2).
10. TPower-up: Assumes a linear ramp from 0V to VDD (min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document #: 38-05678 Rev. *B
Page 7 of 13
[+] Feedback
CY7C1334H
Capacitance[11]
Parameter
Description
Test Conditions
CIN
Input Capacitance
CCLK
Clock Input Capacitance
CI/O
Input/Output Capacitance
100 TQFP
Max.
Unit
5
pF
TA = 25°C, f = 1 MHz,
VDD = 3.3V,
VDDQ = 2.5V
5
pF
5
pF
100 TQFP
Package
Unit
30.32
°C/W
6.85
°C/W
Thermal Resistance[11]
Parameter
ΘJA
ΘJC
Description
Test Conditions
Thermal Resistance Test conditions follow standard test methods and
(Junction to Ambient) procedures for measuring thermal impedance, per
Thermal Resistance EIA/JESD51
(Junction to Case)
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
10%
R = 351Ω
(a)
INCLUDING
JIG AND
SCOPE
2.5V I/O Test Load
(b)
(c)
10%
(a)
90%
10%
90%
GND
5 pF
VT = 1.25V
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
≤ 1 ns
≤ 1 ns
R = 1667Ω
2.5V
OUTPUT
90%
10%
90%
GND
5 pF
VL = 1.5V
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
R =1538Ω
INCLUDING
JIG AND
SCOPE
(b)
≤ 1 ns
≤ 1 ns
(c)
Notes:
11. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-05678 Rev. *B
Page 8 of 13
[+] Feedback
CY7C1334H
Switching Characteristics Over the Operating Range [12, 13]
166 MHz
Parameter
tPOWER
Description
[14]
VDD (typical) to the First Access
Min.
Max.
1
133 MHz
Min.
Max.
1
Unit
ms
Clock
tCYC
Clock Cycle Time
6.0
7.5
ns
tCH
Clock HIGH
2.5
3.0
ns
tCL
Clock LOW
2.5
3.0
ns
Output Times
tCO
Data Output Valid after CLK Rise
tDOH
Data Output Hold after CLK Rise
1.5
1.5
ns
tCLZ
Clock to
Low-Z[15, 16, 17]
0
0
ns
tCHZ
Clock to
High-Z[15, 16, 17]
tOEV
OE LOW to Output Valid
tOELZ
OE LOW to Output Low-Z[15, 16, 17]
tOEHZ
OE HIGH to Output
3.5
4.0
3.5
3.5
0
High-Z[15, 16, 17]
4.0
ns
4.0
ns
0
3.5
ns
ns
4.0
ns
Set-up Times
tAS
Address Set-up before CLK Rise
1.5
1.5
ns
tALS
ADV/LD Set-up before CLK Rise
1.5
1.5
ns
tWES
GW, BW[A:D] Set-up before CLK Rise
1.5
1.5
ns
tCENS
CEN Set-up before CLK Rise
1.5
1.5
ns
tDS
Data Input Set-up before CLK Rise
1.5
1.5
ns
tCES
Chip Enable Set-Up before CLK Rise
1.5
1.5
ns
tAH
Address Hold after CLK Rise
0.5
0.5
ns
Hold Times
tALH
ADV/LD Hold after CLK Rise
0.5
0.5
ns
tWEH
GW, BW[A:D] Hold after CLK Rise
0.5
0.5
ns
tCENH
CEN Hold after CLK Rise
0.5
0.5
ns
tDH
Data Input Hold after CLK Rise
0.5
0.5
ns
tCEH
Chip Enable Hold after CLK Rise
0.5
0.5
ns
Notes:
12. Test conditions shown in (a), (b) and (c) of AC Test Loads.
13. Timing reference level is 1.5V when VDDQ = 3.3V and 1.25V when VDDQ = 2.5V.
14. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD minimum initially before a Read or Write operation
can be initiated.
15. tCHZ, tCLZ, tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
16. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve Tri-State prior to Low-Z under the same system conditions
17. This parameter is sampled and not 100% tested.
Document #: 38-05678 Rev. *B
Page 9 of 13
[+] Feedback
CY7C1334H
Switching Waveforms
Read/Write Timing[18, 19, 20]
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
A7
10
CLK
tCENS
tCENH
tCH
tCL
CEN
tCES
tCEH
CE
ADV/LD
WE
BW[A:D]
A1
ADDRESS
A2
tCO
tAS
tDS
tAH
Data
tDH
D(A1)
tCLZ
D(A2)
D(A2+1)
tDOH
Q(A3)
tOEV
Q(A4)
tCHZ
Q(A4+1)
D(A5)
Q(A6)
In-Out (DQ)
tOEHZ
tDOH
tOELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
DON’T CARE
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
UNDEFINED
Notes:
18. For this waveform ZZ is tied LOW.
19. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
20. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document #: 38-05678 Rev. *B
Page 10 of 13
[+] Feedback
CY7C1334H
Switching Waveforms (continued)
NOP, STALL, and Deselect Cycles[18, 19, 21]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW[A:D]
ADDRESS
A5
tCHZ
D(A1)
Data
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
DON’T CARE
Q(A2)
D(A4)
Q(A3)
WRITE
D(A4)
STALL
NOP
READ
Q(A5)
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
ZZ Mode Timing[22, 23]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes:
21. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
22. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
23. I/Os are in High-Z when exiting ZZ sleep mode.
Document #: 38-05678 Rev. *B
Page 11 of 13
[+] Feedback
CY7C1334H
Ordering Information
“Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered”.
Speed
(MHz)
Ordering Code
Package
Diagram
Operating
Range
166
CY7C1334H-166AXC
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1334H-166AXI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
133
CY7C1334H-133AXC
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Commercial
CY7C1334H-133AXI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
Package Type
Commercial
Package Diagram
100-pin TQFP (14 x 20 x 1.4 mm) (51-85050)
16.00±0.20
1.40±0.05
14.00±0.10
81
100
80
1
20.00±0.10
22.00±0.20
0.30±0.08
0.65
TYP.
30
12°±1°
(8X)
SEE DETAIL
A
51
31
50
0.20 MAX.
0.10
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
NOTE:
1. JEDEC STD REF MS-026
GAUGE PLANE
0°-7°
R 0.08 MIN.
0.20 MAX.
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0.60±0.15
0.20 MIN.
51-85050-*B
1.00 REF.
DETAIL
A
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device
Technology, Inc. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05678 Rev. *B
Page 12 of 13
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY7C1334H
Document History Page
Document Title: CY7C1334H 2-Mbit (64K x 32) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05678
REV.
ECN NO. Issue Date
Orig. of
Change
Description of Change
**
347357
See ECN
PCI
New Data Sheet
*A
424820
See ECN
RXU
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed Three-State to Tri-State.
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the
Electrical Characteristics Table.
Modified test condition from VDDQ < VDD to VDDQ < VDD
Replaced Package Name column with Package Diagram in the Ordering
Information table.
Replaced Package Diagram of 51-85050 from *A to *B
*B
459347
See ECN
NXR
Converted from Preliminary to Final
Included 2.5V I/O option
Updated the Ordering Information table.
Document #: 38-05678 Rev. *B
Page 13 of 13
[+] Feedback