DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 CUSTOMER APPROVAL ※ PART NO. : APPROVAL COMPANY CHOP CUSTOMER COMMENTS DISPLAYTRONIC ENGINEERING APPROVAL DESIGN BY CHECKED BY APPROVED BY AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 REVISION RECORD REVISION VER1.0 VER2.0 REVISION DATE 2008-02-03 PAGE CONTENTS FIRST ISSUE 2008-02-21 DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 1 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 ※ CONTENTS 1.0 MECHANICAL DIAGRAM 2.0 MECHANICAL SPECS 3.0 ABSOLUTE MAXIMUM RATINGS 4.0 ELECTRICAL CHARACTERISTICS 5.0 OPTICAL CHARACTERISTICS 6.0 BLOCK DIAGRAM 7.0 PIN ASSIGNMENT 8.0 APPLICATION 9.0 TIMING CHARACTERISTICS 10.0 RELIABILITY TEST 11.0 DISPLAY CONTROL INSTRUCTION 12.0 PRECAUTION FOR USING LCM DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 2 LCD SPECIFICATION DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 1/1 1.0 XIAMEN ZETTLER ELECTRONICS CO., LTD. DISPLAYTRONIC NC 20 DB7 19 DB6 18 DB5 17 DB4 16 DB3 15 DB2 14 DB1 13 DB0 12 Reset 11 HALT 10 C/D 9 CE 8 RD 7 WR 6 Vee 5 Vadj 4 Vdd 3 Vss 2 FG 1 PIN NO. SYMBOL AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 MECHANICAL DIAGRAM 3 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 2.0 MECHANICAL SPECS 1. Overall Module Size 2. 3. 4. 5. 6. 7. 8. 9. 129.0mm(W) x 102.0mm(H) x max 16.5mm(D) for LED backlight version 0.54mm(W) x 0.54mm(H) 0.58mm(W) x 0.58mm(H) 1/128 T6963C FSTN TRANSFLECTIVE WHITE SIDE LED Wide (-20ºC ~ 60ºC) Dot Size Dot Pitch Duty Controller IC LC Fluid Options Polarizer Options Backlight Options Temperature Range Options 3.0 ABSOLUTE MAXIMUM RATINGS Item Symbol Min Typ Max Unit Operating temperature (Wide temperature) Top -20 - 60 ºC Storage temperature (Wide temperature) Tst -30 - 70 ºC Input voltage Vin -0.3 - Vdd+0.3 V Vdd- Vss -0.3 - 7.0 V Vdd- VLCD 6 - 28 V Supply voltage for logic Supply voltage for LCD drive 4.0 ELECTRICAL CHARACTERISTICS Item Symbol Condition Min Typ Max Unit Input voltage (high) Vih H level Vdd-2.2 - Vdd V Input voltage (low) Vil L level 0 - 0.8 V -20ºC - - - 0ºC - - - 25ºC - 19.1 - 70ºC - - - Idd Vdd=5.0V - 24.5 35.0 mA LED Power Supply Voltage Vop=(VA-VK) - 2.9 3.2 3.5 V LED Power Supply Current Iled(WHITE) RL=0Ω - 135 - mA Recommended LC Driving Voltage Vdd -VLCD Power Supply Current DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. V 4 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 5.0 OPTICAL CHARACTERISTICS Item Mode R S Cr (Contrast Ratio) θ (Viewing Angle) φ (Viewing Angle) 25ºC 25ºC 25ºC MIN. TYP. MIN TYP. MIN TYP. A 2.8 3.05 80° 85° - 35° B 7.10 7.70 80° 85° - 35° C - - - - - - A 2.49 2.99 80° 85° - 35° B 7.05 7.55 80° 85° - 35° C - - - - - - Note: R: Reflective S: Transflective A: STN Gray B: STN Yellow C: FSTN At: φ =0°, θ =0° Item Symbol Condition Min Typ Max Unit Response time (rise) Tr 25 ºC - 150 250 ms Response time (fall) Tf 25ºC - 150 250 ms 6.0 BLOCK DIAGRAM C1 DC/DC 0086 BIAS C64 C65 0086 T6963 LED Backlight DISPLAYTRONIC C128 S1 - S80 S81 - S160 0086 0086 XIAMEN ZETTLER ELECTRONICS CO., LTD. 5 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 7.0 PIN ASSIGNMENT Pin No. Symbol Function 1 FG Frame Ground 2 VSS Ground 3 VDD +5V 4 VADJ 5 VEE 6 /WR WRITE SIGNAL 7 /RD READ SIGNAL 8 /CE Chip Enable 9 C/D Command/Data 10 /HALT 11 /RESET Reset 12 Data bit 0 13 DB0 DB1 14 DB2 Data bit 2 15 DB3 Data bit 3 16 DB4 Data bit 4 17 DB5 Data bit 5 18 DB6 Data bit 6 19 20 DB7 Data bit 7 NC NO CONNECTION Power supply for LCD driving NEGATIVE VOLTAGE SUPPLY Data bit 1 A K 8.0 3.2V 0V APPLICATION DB0-DB7 P0 C/D P3.0 P2 DECODE /CE WR /WR RD /RD RST /RESET AGM1612B 51 SERIES MCU DISPLAYTRONIC VEE VADJ VSS XIAMEN ZETTLER ELECTRONICS CO., LTD. 6 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 9.0 TIMING CHARACTERISTICS Tah C/D Tcyc Taw Tcc RD# WR# Tds Tdh Data Write Tacc Toh Data Read ITEM Address Setup Time Address Hold Time RD#,WR# Cycle RD#,WR# Pulse Width Data Setup Time Data Hold Time (Write) Data Access Time Data Hold Time (Read) SYMBLE Taw Tah Tcyc Tcc Tds Tdh Tacc Toh MIN 10 10 200 80 80 40 MAX 150 50 10 UNIT ns ns ns ns ns ns ns ns 10.0 RELIABILITY TEST Evaluations and Assessment* Content Current Consumption Oozing Contrast Other Appearances 40ºC,90% RH,96hrs Twice initial value or less none More than 80% of initial value No abnormality 60ºC, 96hrs -20ºC, 96hrs Twice initial value or less Twice initial value or less none More than 80% of initial value No abnormality More than 80% of initial value No abnormality Storage Condition Operation at high temperature and humidity High temperature storage Low temperature storage *Evaluations and assessment to be made two hours after returning to room temperature (25ºC±5ºC). *The LCDs subjected to the test must not have dew condensation. DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 7 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 11.0 DISPLAY CONTROL INSTRUCTION The display control instructions control the internal state of the T6963c. COMMAND Control State CD RD WR Code D7 D6 D5 D4 D3 D2 D1 D0 DESCRIPTION N2 N1 N0 0 0 1 Set Cursor Pointer 0 1 0 Set Offset Register 1 0 0 Set address Pointer N1 N0 0 0 Set Text Home Address 1 1 Set Text Area 2 0 Set Graphic Home Address 1 1 Set Graphic Area CG=0: Internal CG ROM Mode CG=1: Internal CG ROM Mode N2 N1 N0 Graphic & Text 0 0 0 OR Mode 0 0 1 Exor Mode 0 1 1 And Mode 1 0 0 Text Attribute Mode N3=0: Display Off N3=1: Display On N2=0:Text Off N2=1: Text On N1=0: Cursor Off N1=1: Cursor On N0=0: Blink Off N0=1: Blink On N2,N1,N0 Line Number of Cursor N2 N1 N0 0 0 0 1-Line Cursor (Bottom Line) 1 1 1 8-Line Cursor (8x8Dots) N1 N0 0 0 Data Auto Write 0 1 Data Auto Read 1 * Auto Reset N2=0: ADP Variable N2=1: ADP Nonvariable N1=0: Increment ADP N1 =1: Decrement ADP N0=0: Data Write N0=1: Data Read REGISTERS SETTIBG 1 1 0 0 0 1 0 0 N2 N1 N0 SET CONTROL WORD 1 1 0 0 1 0 0 0 0 N1 N0 MODE SET 1 1 0 1 0 0 0 C G N2 N1 N0 DISPLAY MODE 1 1 0 1 0 0 1 N3 N2 N1 N0 CURSOR PATTERN SELECT 1 1 0 1 0 1 0 0 N2 N1 N0 DATA AUTO READ/WRITE 1 1 0 1 0 1 1 0 0 N1 N0 DATA READ/WRITE 1 1 0 1 1 0 0 0 N2 N1 N0 1 1 0 1 1 1 0 0 0 0 0 Screan Peek 1 1 0 1 1 1 0 1 0 0 0 Screen Copy SCREEN PEEK SCREEN COPY BIT SET/RESET 1 1 0 DATA WRITE 0 1 0 Write Data DATA READ 0 0 1 Read Data DISPLAYTRONIC 1 1 1 1 N3 N2 N1 N0 XIAMEN ZETTLER ELECTRONICS CO., LTD. N3=0: Bit Reset N3=1: Bit Set N2, N1, N0 Bit Address 000-D0, 111-D7 Writes data DB0~DB7 into display data RAM. After writing instruction Reads data DB0~DB7 from display data RAM to the data bus. 8 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 12.0 RECAUTION FOR USING LCM 1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage. 2. As LCD panel is made of glass substrate, Dropping the LCD module or banging it against hard objects may cause cracking or fragmentation. Especially at corners and edges. 3. Although the polarizer of this LCD Module has the anti-glare coating, always be careful not to scratch its surface. Use of a plastic cover is recommended to protect the surface of polarizer. 4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If it is stored at above specified temperature, the molecular orientation of the LC material may change to Liquid state and it may not revert to its original state. Excessive temperature and humidity could cause polarizer peel off or bubble. Therefore, the LCD module should always be stored within specified temperature range. 5. Saliva or water droplets must be wiped off immediately as those may leave stains or cause color changes if remained for a long time. Water vapor will cause corrosion of ITO electrodes. 6. If the surface of LCD panel needs to be cleaned, wipe it swiftly with cotton or other soft cloth. If it is not still clean enough, blow a breath on the surface and wipe again. 7. The module should be driven according to the specified ratings to avoid malfunction and permanent damage. Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latchup of driver LSIs and DC charge up to LCD panel. 8. Mechanical Considerations a) LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not make any alterations or modifications. The following should be noted. b) Do not tamper in any way with the tabs on the metal frame. c) Do not modify the PCB by drilling extra holes, changing its outline, moving its components or modifying its pattern. d) Do not touch the elastomer connector; especially insert a backlight panel (for example, EL). e) When mounting a LCM makes sure that the PCB is not under any stress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. f) Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose contact, resulting in missing pixels. 9. Static Electricity a) Operator Ware the electrostatics shielded clothes because human body may be statically charged if not ware shielded clothes. Never touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals with any parts of the human body. b) Equipment There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance 8 (electrostatic earth: 1x10 ohm). Only properly grounded soldering irons should be used. If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks. The normal static prevention measures should be observed for work clothes and working benches; for the latter conductive (rubber) mat is recommended. c) Floor Floor is the important part to drain static electricity, which is generated by operators or equipment. There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the electrostatic earth (electrostatic earth: 1x108 ohm). d) Humidity Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over 50%RH. e) Transportation/storage The storage materials also need to be anti-static treated because there is a possibility that the human body or storage materials such as containers may be statically charged by friction or peeling. The modules should be kept in antistatic bags or other containers resistant to static for storage. f) Soldering Solder only to the I/O terminals.Use only soldering irons with proper grounding and no leakage. Soldering temperature : 280°C ± 10°C DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 9 AGM1612B-FLW-FBW GRAPHIC MODULE VER2.0 Soldering time: 3 to 4 sec. Use eutectic solder with resin flux fill. If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed afterwards. g) Others The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or stains. It should be peeled off slowly using static eliminator. Static eliminator should also be installed to the workbench to prevent LCD module from static charge. 10. Operation a) Driving voltage should be kept within specified range; excess voltage shortens display life. b) Response time increases with decrease in temperature. c) Display may turn black or dark blue at temperatures above its operational range; this is (however not pressing on the viewing area) may cause the segments to appear “fractured”. d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the segments to appear “fractured”. 11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water. The toxicity is extremely low but caution should be exercised at all the time. 12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided. 13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention, do not apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed after display pattern is changed. 14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent (dealcohol or deoxym) to prevent discoloration of polarizer due to gas. 15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time. The brightness of LCD module may be affected by the routing of CCFL cables due to leakage to the chassis through coupling effect. The inverter circuit needs to be designed taking the level of leakage current into consideration. Thorough evaluation is needed for LCD module and inverter built into its host equipment to DISPLAYTRONIC XIAMEN ZETTLER ELECTRONICS CO., LTD. 10