IRFP064, SiHFP064 Vishay Siliconix Power MOSFET FEATURES PRODUCT SUMMARY VDS (V) • • • • • • • • 60 RDS(on) (Ω) VGS = 10 V 0.009 Qg (Max.) (nC) 190 Qgs (nC) 55 Qgd (nC) 90 Configuration Single D TO-247 Dynamic dV/dt Rating Repetitive Avalanche Rated Ultra Low On- Resistance Very Low Thermal Resistance Isolated Central Mounting Hole 175 °C Operating Temperature Fast Switching Lead (Pb)-free Available Available RoHS* COMPLIANT DESCRIPTION Third generation Power MOSFETs from Vishay provide the designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. The TO-247 package is preferred for commercial-industrial applications where higher power levels preclude the use of TO-220 devices. The TO-247 is similar but superior to the earlier TO-218 package because its isolated mounting hole. It also provides greater creepage distances between pins to meet the requirements of most safety specifications. G S D G S N-Channel MOSFET ORDERING INFORMATION Package TO-247 IRFP064PbF SiHFP064-E3 IRFP064 SiHFP064 Lead (Pb)-free SnPb ABSOLUTE MAXIMUM RATINGS TC = 25 °C, unless otherwise noted PARAMETER SYMBOL LIMIT VDS VGS 60 ± 20 70 70 520 2.0 1000 70 30 300 4.5 - 55 to + 175 300 10 1.1 Drain-Source Voltage Gate-Source Voltage Continuous Drain Currente VGS at 10 V Pulsed Drain Currenta Linear Derating Factor Single Pulse Avalanche Energyb Repetitive Avalanche Currenta Repetitive Avalanche Energya Maximum Power Dissipation Peak Diode Recovery dV/dtc Operating Junction and Storage Temperature Range Soldering Recommendations (Peak Temperature)d Mounting Torque TC = 25 °C TC = 100 °C ID IDM TC = 25 °C EAS IAR EAR PD dV/dt TJ, Tstg for 10 s 6-32 or M3 screw UNIT V A W/°C mJ A mJ W V/ns °C lbf · in N·m Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. VDD = 25 V, starting TJ = 25 °C, L = 69 µH, RG = 25 Ω, IAS = 130 A (see fig. 12). c. ISD ≤ 130 A, dI/dt ≤ 300 A/µs, VDD ≤ VDS, TJ ≤ 175 °C. d. 1.6 mm from case. e. Current limited by the package (die current = 130 A). * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 WORK-IN-PROGRESS www.vishay.com 1 IRFP064, SiHFP064 Vishay Siliconix THERMAL RESISTANCE RATINGS PARAMETER SYMBOL TYP. MAX. Maximum Junction-to-Ambient RthJA - 40 Case-to-Sink, Flat, Greased Surface RthCS 0.24 - Maximum Junction-to-Case (Drain) RthJC - 0.50 UNIT °C/W SPECIFICATIONS TJ = 25 °C, unless otherwise noted PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Static Drain-Source Breakdown Voltage VDS Temperature Coefficient Gate-Source Threshold Voltage Gate-Source Leakage Zero Gate Voltage Drain Current Drain-Source On-State Resistance Forward Transconductance VDS VGS = 0 V, ID = 250 µA 60 - - V ΔVDS/TJ Reference to 25 °C, ID = 1 mA - 0.048 - V/°C VGS(th) VDS = VGS, ID = 250 µA 2.0 - 4.0 V IGSS VGS = ± 20 V - - ± 100 nA VDS = 60 V, VGS = 0 V - - 25 VDS = 48 V, VGS = 0 V, TJ = 150 °C - - 250 IDSS RDS(on) gfs ID = 78 Ab VGS = 10 V VDS = 25 V, ID = 78 Ab µA - - 0.009 Ω 38 - - S - 7400 - - 3200 - - 540 - - - 190 Dynamic Input Capacitance Ciss Output Capacitance Coss VGS = 0 V, VDS = 25 V, f = 1.0 MHz, see fig. 5 pF Reverse Transfer Capacitance Crss Total Gate Charge Qg Gate-Source Charge Qgs - - 55 Gate-Drain Charge Qgd - - 90 Turn-On Delay Time td(on) - 21 - tr - 190 - - 110 - - 190 - - 5.0 - - 13 - - - 70c - - 520 - - 3.0 V - 160 250 ns - 0.9 1.7 µC Rise Time Turn-Off Delay Time Fall Time td(off) VGS = 10 V ID = 130 A, VDS = 48 V, see fig. 6 and 13b VDD = 30 V, ID = 130 A, RG = 4.3 Ω, RD = 0.22 Ω, see fig. 10b tf Internal Drain Inductance LD Internal Source Inductance LS Between lead, 6 mm (0.25") from package and center of die contact D nC ns nH G S Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulsed Diode Forward Currenta ISM Body Diode Voltage VSD Body Diode Reverse Recovery Time trr Body Diode Reverse Recovery Charge Qrr Forward Turn-On Time ton MOSFET symbol showing the integral reverse p - n junction diode D A G TJ = 25 °C, IS = 130 A, VGS = 0 S Vb TJ = 25 °C, IF = 130 A, dI/dt = 100 A/µsb Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD) Notes a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. Pulse width ≤ 300 µs; duty cycle ≤ 2 %. c. Current limited by the package (die current = 130 A). www.vishay.com 2 Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 IRFP064, SiHFP064 Vishay Siliconix TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted Fig. 1 - Typical Output Characteristics, TC = 25 °C Fig. 2 - Typical Output Characteristics, TC = 175 °C Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 Fig. 3 - Typical Transfer Characteristics Fig. 4 - Normalized On-Resistance vs. Temperature www.vishay.com 3 IRFP064, SiHFP064 Vishay Siliconix Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage Fig. 7 - Typical Source-Drain Diode Forward Voltage Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage Fig. 8 - Maximum Safe Operating Area www.vishay.com 4 Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 IRFP064, SiHFP064 Vishay Siliconix RD VDS VGS D.U.T. RG + - VDD 10 V Pulse width ≤ 1 µs Duty factor ≤ 0.1 % Fig. 10a - Switching Time Test Circuit VDS 90 % 10 % VGS td(on) Fig. 9 - Maximum Drain Current vs. Case Temperature tr td(off) tf Fig. 10b - Switching Time Waveforms Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 www.vishay.com 5 IRFP064, SiHFP064 Vishay Siliconix L Vary tp to obtain required IAS VDS VDS tp VDD D.U.T. RG + - I AS V DD VDS 10 V 0.01 Ω tp IAS Fig. 12a - Unclamped Inductive Test Circuit Fig. 12b - Unclamped Inductive Waveforms Fig. 12c - Maximum Avalanche Energy vs. Drain Current Current regulator Same type as D.U.T. 50 kΩ QG 10 V 12 V 0.2 µF 0.3 µF QGS QGD + D.U.T. VG - VDS VGS 3 mA Charge IG ID Current sampling resistors Fig. 13a - Basic Gate Charge Waveform www.vishay.com 6 Fig. 13b - Gate Charge Test Circuit Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 IRFP064, SiHFP064 Vishay Siliconix Peak Diode Recovery dV/dt Test Circuit + D.U.T. Circuit layout considerations • Low stray inductance • Ground plane • Low leakage inductance current transformer + - - RG • • • • dV/dt controlled by RG Driver same type as D.U.T. ISD controlled by duty factor "D" D.U.T. - device under test Driver gate drive P.W. + Period D= + - VDD P.W. Period VGS = 10 V* D.U.T. ISD waveform Reverse recovery current Body diode forward current dI/dt D.U.T. VDS waveform Diode recovery dV/dt Re-applied voltage VDD Body diode forward drop Inductor current Ripple ≤ 5 % ISD * VGS = 5 V for logic level devices Fig. 14 - For N-Channel Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?91201. Document Number: 91201 S-Pending-Rev. A, 24-Jun-08 www.vishay.com 7 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1