PRODUCT: PESD0402-060 ESD Protector Overvoltage Protection Device 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Raychem Circuit Protection Products DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 1 OF 8 Specification Status: Released Not to be used for new designs. For new design please contact Tyco Electronics Sales BENEFITS • Board space savings • Help protect sensitive electronic circuits against damage from electrostatic discharge (ESD) • Assist equipment to pass IEC 61000-4-2, level 4 testing FEATURES • • • • • • • Thick film technology Low capacitance (0.25 pF typical) Low trigger voltage Low clamping voltage Capable of withstanding numerous ESD strikes Compatible with standard reflow installation procedures Bi-directional protection APPLICATIONS • Cellular phones Caution: This part is not intended to be used under bias, nor for power bus nor data line applications. It is only to be used in RF applications. MATERIALS INFORMATION ROHS Compliant ELV Compliant PART NUMBERING PESD 0402 - 060 Series Operating Voltage Designator 0 6 x 10 = 6VDC EIA Size The operating voltage is used to measure leakage current @ 1s PRODUCT: PESD0402-060 ESD Protector Overvoltage Protection Device 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Raychem Circuit Protection Products DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 2 OF 8 TYPICAL DEVICE RATINGS AND CHARACTERISTICS Typical Typical Typical IEC IEC TLP Clamping Trigger Voltage1 Trigger Voltage1 Voltage2 after 30ns VT(IEC) VC(IEC) VT(TLP) V V V 150 25 225 Symbol Unit Value Typical Typical TLP TLP Clamping Clamping Voltage2 2 Voltage after 60ns after 30ns VC(TLP 30) V 40 VC(TLP 60) V 35 Typical Capacitance @ 1 MHz, 1Vrms Cp pF 0.25 Note 1: Measured during IEC 61000-4-2, level 4 pulse, 8kV contact test method Note 2: TLP test method at 1000V (refer to graph on next page). GENERAL CHARACTERISTICS Operating temperature: -55°C … + 110°C Storage temperature: -40°C … + 85°C ESD voltage capability (tested per IEC 61000-4-2) o o Contact discharge mode: typical 8kV, max 15kV Air discharge mode: typical 15kV, max 25kV ESD pulse withstand: Typically 500 pulses (tested per IEC 61000-4-2, level 4, contact method) Environmental Specifications Thermal Shock Heat Storage Test Solderability Solder Heat Test Conditions Pass/Fail Criteria IL≤10µA Mechanical Shock Solvent Resistance 1500G, 0.5ms, X-YZ axis, 3 times IPA ultrasonic 300s IL≤10µA IL≤10µA 110 C, 1000hours 230 C±5 C 3±1s, 95% coverage 260 C, 10s 10 to 50Hz,60s cycle, 2hrs each in X-Y-Z axis IL≤10µA IL≤10µA IL≤10µA IL≤10µA o -55 C to 125oC 30min dwell 1000 cycles Vibration o o o o PRODUCT: PESD0402-060 ESD Protector 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 3 OF 8 Overvoltage Protection Device Raychem Circuit Protection Products TYPICAL TRANSMISSION LINE PULSE RESPONSE GRAPH 500 450 400 350 Voltage (V) 300 250 200 150 100 50 0 0 10 20 30 40 50 Time (ns) 60 70 80 90 100 PRODUCT: PESD0402-060 ESD Protector 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 4 OF 8 Overvoltage Protection Device Raychem Circuit Protection Products DIMENSIONS D A B C Drawing Not To Scale Length A MIN MAX mm: in*: 0.95 (0.037) 1.05 (0.041) Height B MIN MAX 0.28 (0.008) *Rounded off approximation 0.43 (0.017) Terminal Width C MIN MAX 0.1 (0.004) 0.3 (0.010) Width D MIN MAX 0.45 (0.018) 0.55 (0.022) PRODUCT: PESD0402-060 ESD Protector 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Overvoltage Protection Device Raychem Circuit Protection Products DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 5 OF 8 RECOMMENDED LAND PATTERN: X W Y Solder thickness 0.15 to 0.2mm Z W mm: in: * Min 0.6 (0.024) X Max 0.7 (0.028) Min 0.3 (0.012) Max 0.4 (0.016) Y (Ref) Min Max 0.8 0.9 (0.031) (0.035) Z Min 2.1 0.083) *Rounded off approximation. SOLDER REFLOW RECOMMENDATIONS: A Temperature ramp up 1 From ambient to Preheating temperature 30s to 60s B Preheating 140°C - 160°C 60s to 120s C Temperature ramp up 2 D Main heating E Cooling From Preheating to Main heating temperature at 200°C at 220°C at 240°C at 260°C From main heating temperature to 100°C 20s to 40s 60s ~ 70s 50s ~ 60s 30s ~ 40s 5s ~ 10s max 4°C/s Max 2.2 (0.087) PRODUCT: PESD0402-060 ESD Protector 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Overvoltage Protection Device Raychem Circuit Protection Products DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 6 OF 8 PACKAGING Packaging Tape & Reel Standard Box PESD0402-060 10,000 50,000 PRODUCT: PESD0402-060 ESD Protector DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 7 OF 8 Overvoltage Protection Device 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Raychem Circuit Protection Products EIA referenced Reel Dimensions for PESD Devices Reel Dimensions (mm): 0402 Devices A 178.0 ±2.0 B 2.0 ±0.5 C 13.0±0.5 D 21.0±0.8 E 62.0±1.5 F 9.0±0.5 G 13.0±1.0 Carrier Dimensions (mm): 0402 Devices A 8.0±0.3 B 3.5±0.05 C 1.75±0.1 D 2.0±0.05 E 4.0±0.1 F 1.5±0.1 L 1.15±0.2 W 0.65±0.05 T1 0.40±0.05 Product Orientation – always face up (meaning the substrate is at the bottom), but parts do not have polarity mark. Leader & Trailer: The leader is 180mm in length & consists of empty cavities with sealed cover tape. The trailer is 350mm in length & consists of empty cavities with sealed cover tape. PRODUCT: PESD0402-060 ESD Protector 308 Constitution Drive Menlo Park, CA 94025-1164 Phone: 800-227-4856 www.circuitprotection.com Overvoltage Protection Device Raychem Circuit Protection Products DOCUMENT: SCD 26105 REV LETTER: I REV DATE: DECEMBER 7, 2007 PAGE NO.: 8 OF 8 POST REFLOW, CLEANING CONDITIONS A 5% saponofier combined with water during wash. For Ultrasonic process water temperature should be at 50°C and board should be submerged for a minimum of one minute in the solutions, then rinse and dry. For in-line washing, the temperature of the water sprayed should be at 110°C, rinse and drying is done in-line. Warning: Application Limitations for PESD0402-060. This part is not intended to be used under bias, nor for power bus nor data line applications. It is only to be used in RF applications. Users should independently evaluate the suitability of and test each product selected for their own applications Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Tyco Electronics reserves the right to change or update, without notice, any information contained in this publication; to change, without notice, the design, construction, processing, or specification of any product; and to discontinue or limit production or distribution of any product. This publication supersedes and replaces all information previously supplied. Without expressed or written consent by an officer of Tyco Electronics, Tyco Electronics does not authorize the use of any of its products as components in nuclear facility applications, aerospace, or in critical life support devices or systems. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics’ only obligations are those in the Tyco Electronics Standard Terms and Conditions of Sale and in no case will Tyco Electronics be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of its products. © 2004, 2007 Tyco Electronics Corporation. All rights reserved.