LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * * * * * * Package in 8mm tape on 7" diameter reels. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. EIA STD package. I.C. compatible. Meet green product and Pb-free(According to RoHS) Package Dimensions Part No. Lens Color Source Color LTW-089E2CG-A Yellow InGaN White Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1 mm (.004") unless otherwise noted. Definition of Distance Between of PAD and Reflector A: The distance between pad’s bottom and reflector. B: The tolerance between right and left pad. C: The distance between pad and reflector. Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Symbol A B C 0 0 0 Dimension (mm) min 0.05 min 0.03 min 0.05 Page : 1 max max max of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ℃ Absolute Maximum Ratings at Ta=25℃ Parameter LTW-089E2CG-A Unit Power Dissipation (30mA, 4V) 120 mW Power Dissipation (20mA, 3.5V) 70 mW 100 mA DC Forward Current 30 mA Reverse Voltage 5 V Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Operating Temperature Range -30℃ to + 85℃ Storage Temperature Range -40℃ to + 100℃ Reflow Soldering Condition 260℃ For 10 Seconds Suggest IR Reflow Condition : R-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B) Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 2 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical Optical Characteristics At ℃ Ta=25℃ Symbol Part No. LTW- Min. Luminous Flux lm 089E2CG-A 4.0 Luminous Intensity Iv 089E2CG-A 2000 2θ1/2 089E2CG-A 120 Parameter Viewing Angle Chromaticity Coordinates x Typ. Max. Unit Test Condition 6.6 lm IF = 20mA Note 1, 2 IF = 20mA Note 1, 2 deg 0.300 089E2CG-A y IF = 20mA Note 3, 5, 6 0.285 Forward Voltage VF 089E2CG-A 3.0 ESD-Withstand Voltage ESD 089E2CG-A 1K 3.2 Fig.6 3.4 V IF = 20mA V HBM Note : 1. Luminous Flux is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. Flux classification code is marked on each packing bag. 3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram. 4. Caution in ESD: Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. CAS140B is the test standard for the chromaticity coordinates (x, y) 6. Chromaticity coordinates (x, y) is tested by IS. 7. The chromaticity coordinates (x, y) guarantee should be added +/- 0.005 tolerance. Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 3 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List Luminous Spec. Table Flux (lm) and IV (mcd) at IF = 20mA IV Bin lm mcd Min. Max. Min. Max. 5 4.0 4.3 1550 1650 6 4.3 4.6 1650 1750 7 4.6 4.9 1750 1850 8 4.9 5.3 1850 2000 9 5.3 5.7 2000 2150 10 5.7 6.1 2150 2300 11 6.1 6.6 2300 2500 Tolerance on each Luminous Intensity bin and Luminous Flux are +/- 7%, and IV (mcd) is for reference. Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 4 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Color Spec. Table @20mA CA1 x 0.2800 0.2780 0.2805 0.2824 CA2 y 0.2615 0.2640 0.2675 0.2649 x 0.2824 0.2805 0.2830 0.2848 0.2590 0.2615 0.2649 0.2625 0.2843 0.2824 0.2848 0.2865 0.2565 0.2590 0.2625 0.2598 0.2862 0.2843 0.2865 0.2883 0.2540 0.2565 0.2598 0.2573 0.2879 0.2862 0.2883 0.2900 0.2540 0.2515 0.2548 0.2573 0.2879 0.2896 0.2917 0.2900 y 0.2758 0.2780 0.2816 0.2794 x 0.2915 0.2902 0.2925 0.2938 0.2730 0.2758 0.2794 0.2765 0.2931 0.2915 0.2938 0.2953 0.2703 0.2730 0.2765 0.2738 0.2946 0.2931 0.2953 0.2968 0.2680 0.2703 0.2738 0.2714 0.2960 0.2946 0.2968 0.2980 0.2680 0.2657 0.2690 0.2714 0.2960 0.2974 0.2992 0.2980 CB1 0.2820 0.2800 0.2824 0.2843 0.2573 0.2548 0.2586 0.2610 0.2900 0.2917 0.2936 0.2920 y 0.2794 0.2816 0.2855 0.2831 x 0.2938 0.2925 0.2946 0.2958 0.2765 0.2794 0.2831 0.2803 0.2953 0.2938 0.2958 0.2973 0.2738 0.2765 0.2803 0.2773 0.2968 0.2953 0.2973 0.2988 0.2714 0.2738 0.2773 0.2750 0.2980 0.2968 0.2988 0.3000 0.2714 0.2690 0.2727 0.2750 0.2980 0.2992 0.3012 0.3000 0.2660 0.2684 0.2720 0.2694 0.2887 0.2870 0.2893 0.2910 0.2634 0.2660 0.2694 0.2668 0.2904 0.2887 0.2910 0.2926 0.2610 0.2634 0.2668 0.2645 0.2920 0.2904 0.2926 0.2940 0.2610 0.2586 0.2622 0.2645 0.2920 0.2936 0.2954 0.2940 y 0.2831 0.2855 0.2890 0.2867 x 0.2958 0.2946 0.2970 0.2982 0.2803 0.2831 0.2867 0.2838 0.2973 0.2958 0.2982 0.2995 0.2773 0.2803 0.2838 0.2808 0.2988 0.2973 0.2995 0.3008 0.2750 0.2773 0.2808 0.2785 0.3000 0.2988 0.3008 0.3020 0.2750 0.2727 0.2762 0.2785 0.3000 0.3012 0.3033 0.3020 0.2694 0.2720 0.2758 0.2730 CC4 0.2668 0.2694 0.2730 0.2703 CD4 CE3 0.2645 0.2668 0.2703 0.2680 CE4 EA3 0.2645 0.2622 0.2657 0.2680 EA4 EB3 y 0.2867 0.2890 0.2930 0.2903 EB4 EC3 0.2838 0.2867 0.2903 0.2875 EC4 ED3 EE2 y 0.2720 0.2745 0.2780 0.2758 CB4 CD3 ED2 EE1 0.2940 0.2954 0.2974 0.2960 0.2900 0.2883 0.2904 0.2920 EC2 ED1 0.2940 0.2926 0.2946 0.2960 0.2573 0.2598 0.2634 0.2610 x 0.2870 0.2855 0.2880 0.2893 CC3 EB2 EC1 0.2926 0.2910 0.2931 0.2946 0.2883 0.2865 0.2887 0.2904 EA2 EB1 0.2910 0.2893 0.2915 0.2931 0.2598 0.2625 0.2660 0.2634 CA4 y 0.2684 0.2710 0.2745 0.2720 CB3 CE2 EA1 x 0.2893 0.2880 0.2902 0.2915 0.2865 0.2848 0.2870 0.2887 CD2 CE1 0.2860 0.2880 0.2896 0.2879 0.2625 0.2649 0.2684 0.2660 CC2 CD1 0.2860 0.2840 0.2862 0.2879 x 0.2848 0.2830 0.2855 0.2870 CB2 CC1 0.2840 0.2820 0.2843 0.2862 CA3 y 0.2649 0.2675 0.2710 0.2684 0.2808 0.2838 0.2875 0.2848 ED4 EE3 0.2785 0.2808 0.2848 0.2820 EE4 0.2785 0.2762 0.2793 0.2820 Color Coordinates Measurement allowance is ±0.005 Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 5 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Color Spec. Table @20mA WA1 x y 0.2982 0.2903 0.2970 0.2930 0.2990 0.2965 0.3003 0.2937 WB1 0.2995 0.2875 0.2982 0.2903 0.3003 0.2937 0.3015 0.2910 WC1 0.3008 0.2848 0.2995 0.2875 0.3015 0.2910 0.3028 0.2883 WD1 0.3020 0.2820 0.3008 0.2848 0.3028 0.2883 0.3040 0.2855 WE1 0.3020 0.2820 0.3033 0.2793 0.3053 0.2828 0.3040 0.2855 MA1 x y 0.3063 0.3043 0.3050 0.3070 0.3070 0.3105 0.3083 0.3077 MB1 0.3075 0.3015 0.3063 0.3043 0.3083 0.3077 0.3095 0.3050 MC1 0.3088 0.2988 0.3075 0.3015 0.3095 0.3050 0.3108 0.3022 MD1 0.3100 0.2960 0.3088 0.2988 0.3108 0.3022 0.3120 0.2995 ME1 0.3100 0.2960 0.3112 0.2932 0.3132 0.2968 0.3120 0.2995 WA2 x y 0.3003 0.2937 0.2990 0.2965 0.3010 0.3000 0.3023 0.2973 WB2 0.3015 0.2910 0.3003 0.2937 0.3023 0.2973 0.3035 0.2945 WC2 0.3028 0.2883 0.3015 0.2910 0.3035 0.2945 0.3048 0.2918 WD2 0.3040 0.2855 0.3028 0.2883 0.3048 0.2918 0.3060 0.2890 WE2 0.3040 0.2855 0.3053 0.2828 0.3072 0.2862 0.3060 0.2890 MA2 x y 0.3083 0.3077 0.3070 0.3105 0.3090 0.3140 0.3103 0.3113 MB2 0.3095 0.3050 0.3083 0.3077 0.3103 0.3113 0.3115 0.3085 MC2 0.3108 0.3022 0.3095 0.3050 0.3115 0.3085 0.3128 0.3058 MD2 0.3120 0.2995 0.3108 0.3022 0.3128 0.3058 0.3140 0.3030 ME2 0.3120 0.2995 0.3132 0.2968 0.3152 0.3002 0.3140 0.3030 WA3 x y 0.3023 0.2973 0.3010 0.3000 0.3030 0.3035 0.3043 0.3007 WB3 0.3035 0.2945 0.3023 0.2973 0.3043 0.3007 0.3055 0.2980 WC3 0.3048 0.2918 0.3035 0.2945 0.3055 0.2980 0.3068 0.2952 WD3 0.3060 0.2890 0.3048 0.2918 0.3068 0.2952 0.3080 0.2925 WE3 0.3060 0.2890 0.3072 0.2862 0.3092 0.2898 0.3080 0.2925 MA3 x y 0.3103 0.3113 0.3090 0.3140 0.3110 0.3175 0.3123 0.3147 MB3 0.3115 0.3085 0.3103 0.3113 0.3123 0.3147 0.3135 0.3120 MC3 0.3128 0.3058 0.3115 0.3085 0.3135 0.3120 0.3148 0.3092 MD3 0.3140 0.3030 0.3128 0.3058 0.3148 0.3092 0.3160 0.3065 ME3 0.3140 0.3030 0.3152 0.3002 0.3172 0.3038 0.3160 0.3065 WA4 x y 0.3043 0.3007 0.3030 0.3035 0.3050 0.3070 0.3063 0.3043 WB4 0.3055 0.2980 0.3043 0.3007 0.3063 0.3043 0.3075 0.3015 WC4 0.3068 0.2952 0.3055 0.2980 0.3075 0.3015 0.3088 0.2988 WD4 0.3080 0.2925 0.3068 0.2952 0.3088 0.2988 0.3100 0.2960 WE4 0.3080 0.2925 0.3092 0.2898 0.3112 0.2932 0.3100 0.2960 MA4 x y 0.3123 0.3147 0.3110 0.3175 0.3130 0.3210 0.3143 0.3183 MB4 0.3135 0.3120 0.3123 0.3147 0.3143 0.3183 0.3155 0.3155 MC4 0.3148 0.3092 0.3135 0.3120 0.3155 0.3155 0.3168 0.3128 MD4 0.3160 0.3065 0.3148 0.3092 0.3168 0.3128 0.3180 0.3100 ME4 0.3160 0.3065 0.3172 0.3038 0.3192 0.3072 0.3180 0.3100 Color Coordinates Measurement allowance is ±0.005 Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 6 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25°° C Ambient Temperature Unless Otherwise Noted) Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 7 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only User Guide Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less one minute. Recommend Printed Circuit Board Attachment Pad Infrared / vapor phase Reflow Soldering Package Dimensions of Tape Note: 1.All dimensions are in millimeters (inches). Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 8 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-2000 pieces per reel. 3. The maximum number of consecutive missing lamps is two. 4. In accordance with EIA-481-1-B specifications. 5. Vacate 20 cm (min) on start of packing tape and vacate 50 cm (min) on last of packing tape. Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 9 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing this moisture sensitive product is important to ensure the reliability of the product. The package is sealed: The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to solder process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the storage limiting time since opened, that we recommended to baking LEDs at 60°C at least 48hrs. To seal the remainder LEDs return to package, it’s recommended to be with workable desiccants in original package. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Pre-heat Pre-heat time Peak temperature Soldering time 120~150°C 120 sec. Max. 260°C Max. 30 sec. Max. Soldering iron 300°C Max. Temperature Soldering time 3 sec. Max. (one time only) 5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 10 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED’s plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or “ no lightup ” at low currents. To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents. The Vf of “ good ” LEDs should be >[email protected] for InGaN product 7. Reliability Test Temperature No Humidity Items Criteria for judgment Other condition (℃) Hrs Times Sampling (%) LED brightness @ 20mA Vf @ 20mA High temperature 1 100 ----- 1000 30 >70% <110% ----- 1000 30 >70% <110% -40 ----- 1000 30 >70% <110% 25 IF =20mA 1000 30 >70% <110% 25 IF =30mA 500 30 >70% <110% 85 IF =20mA 500 30 >70% <110% IF =20mA 500 30 >70% <110% IF =20mA 1000 30 >70% <110% 195 30 >50% <110% 30 >70% <110% 1 30 >70% <110% 2 30 < ±5% < ±5% 1 30 Go or not Go storage Temperature humidity 2 60 90 storage 3 4 5 Low temp Storage Steady State Operating Life Condition 1 Steady State Operating Life Condition 2 Steady State Operating 6 Life of High Temperature Steady State Operating 7 Life 60 90 of High Humidity Heat Steady State Operating 8 Life -30 of Low Temperature IF =20mA 9 On/Off testing 60 Room Humidity 10 Thermal Shock ------ ------ 11 Thermal Cycle [1] [1] 12 13 Part Resistance to Soldering 10secON /10secOFF 35000 circular Continue -30℃ ~ 85℃ 200 0.5hr. 0.5hr cycles [1] 152 hours/2 cycles TSld = 260℃, 10sec. Heat (Reflow Soldering) Vibration[3] Room Temp No. : LTW-089E2CG-A BNS-OD-C131/A4 Room Humidity Random, 1.5Grms, 10~200Hz, for 30 min changeable vibration per circular X,Y,Z 3 directions 30 min /time Page : 11 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only [1] The thermal profile is shown below 8. Estimated Life time Item Test Condition Min. Typ. Max. Unit Life time(*1) Ta=60℃ IF=20mA Tj≦70℃(*2) 10000 - - hrs (*1)Life time means that estimated time to 50% degradation of initial luminous intensity. (*2)Using testing circuit board: Test board dimension: 25x25x1 mm3 (L x W x H) Material: FR4 Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 12 of 13 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 9. Others The appearance and specifications of the product may be modified for improvement without prior notice. 10. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTW-089E2CG-A BNS-OD-C131/A4 Page : 13 of 13