LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * * * * * * Package in 12mm tape on 7" diameter reels. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. EIA STD package. I.C. compatible. Meet green product and Pb-free(According to RoHS) Package Dimensions Part No. Lens Color Source Color InGaN Blue LTW-008RGB-L Water clear InGaN Green AlInGaP Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1 mm (.004") unless otherwise noted. Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 1 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only °C Absolute Maximum Ratings at Ta=25°C Parameter Rating Unit Symbol R G B Power Dissipation Po 75 120 120 mW Peak Forward Current 1 IFP 100 100 100 mA Continuous Forward Current IF 30 30 30 mA Reverse Voltage VR 5 V Operating Temperature Range Topr -40 ~ +85 °C Storage Temperature Range Tstg -40 ~ +100 °C Soldering Condition Tsol 260°C For 10 Seconds Note 1: 1/10 Duty Cycle, 0.1ms Pulse Width. Suggestion IR Reflow Profile For Pb Free Process : IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B) Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 2 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only °C Absolute Maximum Ratings at Ta=25°C Values Parameter Symbol Min Luminous Intensity 1 IV 2θ1/2 λd B 500 700 100 700 Typ. Min Dominant Wavelength 2 G Typ. Max. Viewing Angle R 1200 520 R: IF = 20mA G: IF = 20mA B: IF = 20mA mcd IF = 20mA ° R: IF = 20mA G: IF = 20mA B: IF = 20mA nm R: IF = 20mA G: IF = 20mA B: IF = 20mA nm R: IF = 20mA G: IF = 20mA B: IF = 20mA V IF = 20mA lm VR = 5V µA IF = 20mA nm 455 Typ. Max. Unit 300 120 610 Test Condition 620 530 465 623 518 455 1.8 3.0 3.0 Min Peak Wavelength λp Typ. Max. Min Forward Voltage 3 VF Typ. Max. 2.4 3.6 3.6 1.57 2.66 0.49 Luminous Flux Φv Typ. Reverse Current IR Max. Spectrum Radiation Bandwidth ∆λ Typ. 10 20 33 22 Note : 1. Tolerance of Luminous Intensity +/- 10% 2. Tolerance of Dominant Wavelength +/- 1nm 3. Tolerance of Forward Voltage +/- 0.1V 4. Caution in ESD: Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. CAS140B is the test standard for the chromaticity coordinates IV. . Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 3 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List VF Spec. Table Forward Voltage (V) at IF: R=20mA, G=20mA, B=20mA Rank Red 1.8 – 2.1 3.0 – 3.3 3.3 – 3.6 3.0 – 3.3 3.3 – 3.6 Green 2.1 – 2.4 3.0 – 3.3 V11 V21 W11 W21 3.3 – 3.6 V12 V22 W12 W22 Blue Tolerance on each Forward Voltage bin is +/- 0.10volt. IV Spec. Table Luminous Intensity (mcd) at IF: R=20mA, G=20mA, B=20mA Rank Red 500 – 700 700 – 800 800 – 900 900 – 1000 1000-1100 1100-1200 100 – 200 A21 A31 A41 A51 A61 200 – 300 A22 A32 A42 A52 A62 Green Blue Tolerance on each Luminous Intensity bin is +/- 10%. Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 4 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List λD Spec. Table Dominated Wavelength (nm) at IF: R=20mA, G=20mA, B=20mA Rank Red 610 – 620 Green 520 – 525 525 – 530 455 – 460 M N 460 – 465 P R Blue Tolerance on each Dominated Wavelength bin is +/- 1nm. Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 5 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 100% Relative Intensity Blue Green Red 80% 60% 40% 20% 0% 350 400 450 500 550 600 650 700 nm Wavelength Fig.1 Relative Intensity vs Dominant Wavelength Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 6 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only User Guide Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less one minute. Recommend Printed Circuit Board Attachment Pad Infrared / vapor phase Reflow Soldering Package Dimensions of Tape Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 7 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-2000 pieces per reel. 3. Minimum packing quantity is 500 pieces for remainders. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with EIA-481-1-B specifications. Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 8 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing this moisture sensitive product is important to ensure the reliability of the product. The package is sealed: The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to solder process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the storage limiting time since opened, that we recommended to baking LEDs at 60°C at least 48hrs. To seal the remainder LEDs return to package, it’s recommended to be with workable desiccants in original package. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Soldering iron Pre-heat 120~150°C Pre-heat time 120 sec. Max. Soldering Temp. 260°C Max. Soldering time 30 sec. Max. Temperature Soldering time 300°C Max. 3 sec. Max. (one time only) 5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 9 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED’s plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward Voltage, or “no light-up” at low currents. To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be>[email protected] for InGaN product. 7.1 Reliability Test Test Item Test Condition Reference Standard Note Number of Damaged Solderability (Reflow Soldering) Tsld=245±5℃, 3sec. (Lead Free Solder) JEITA ED-4701 300 303 1 time Over 95% 0/50 Thermal Shock -30℃ ~ 85℃ 30min. 30min. JEITA ED-4701 300 307 100 cycles 0/50 Temperature Cycle -40℃ ~ 25℃ ~ 100℃ ~ 25℃ 30min. 5min. 30min. 5min. JEITA ED-4701 100 105 100 cycles 0/50 Moisture Resistance Cyclic 25℃ ~ 65℃ ~ -10℃ 90%RH 24HRS./1cycle JEITA ED-4701 200 203 10 cycles 0/50 High Temperature Storage Ta=100℃ JEITA ED-4701 200 201 1000 hrs. 0/50 Temperature Humidity Storage Ta=60℃, RH=90% JEITA ED-4701 100 103 1000 hrs. 0/50 Low Temperature Storage Ta=-40℃ JEITA ED-4701 200 202 1000 hrs. 0/50 Steady State Operating Life Condition 1 Ta=25℃, IF=20mA 1000 hrs. 0/50 Steady State Operating Life Condition 2 Ta=25℃, IF=30mA 500 hrs. 0/50 Steady State Operating Life of High Temperature Ta=85℃, IF=5mA 1000 hrs. 0/50 Steady State Operating Life of High Humidity Heat 60℃, RH=90% , IF=15mA 500 hrs. 0/50 Steady State Operating Life of low Temperature Ta=-30℃, IF=20mA 1000 hrs. 0/50 Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 10 of 11 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 7.2 Criteria for Judging the Damage Criteria for Judgment Min. Max. Item Symbol Test Conditions Forward Voltage VF IF=20mA - - U.S.L.*) × 1.1 Reverse Current IR VR=5V - - U.S.L.*) × 2.0 Luminous Intensity IV IF=20mA - U.S.L.**) × 0.7 - 8. Others The appearance and specifications of the product may be modified for improvement without prior notice. 9. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTW-008RGB-L BNS-OD-C131/A4 Page : 11 of 11