PM6670 Complete DDR2/3 memory power supply controller Preliminary Data Features switching ■ ■ Switching section (VDDQ) – 4.5V to 28V input voltage range – 0.9V, ±1% voltage reference – 1.8V (DDR2) or 1.5V (DDR3) fixed output voltages – 0.9V to 2.6V adjustable output voltage – 1.237V ±1% reference voltage available – Very fast load transient response using constant on-time control loop – No RSENSE current sensing using low side MOSFET’s RDS(ON) – Negative current limit – Latched OVP and UVP – Soft start internally fixed at 3ms – Selectable pulse skipping at light load – Selectable No-Audible (33KHz) pulse skip mode – Ceramic output capacitors supported – Output voltage ripple compensation VTT LDO and VTTREF – 2Apk LDO with foldback for VTT – Remote VTT sensing – High-Z VTT output in S3 – Ceramic output capacitors supported – ±15mA Low noise buffered reference Applications ■ DDR2/3 memory supply ■ Notebook computers ■ Handheld and PDAs ■ CPU and chipset I/O supplies ■ SSTL18, SSTL15 and HSTL bus termination VFQFPN-24 4x4 Description The device PM6670 is a complete DDR2/3 power supply regulator designed to meet JEDEC specifications. It integrates a Constant On-Time (C.O.T.) buck controller, a 2Apk sink/source Low Drop Out regulator and a 15mA low noise buffered reference. The C.O.T. architecture assures fast transient response supporting both electrolytic and ceramic output capacitors. An embedded integrator control loop compensates the DC voltage error due to the output ripple. The 2Apk sink/source linear regulator provides the memory termination voltage with fast load transient response. The device is fully compliant with system sleep states S3 and S4/S5, providing LDO output high impedance in Suspend-To-RAM and Tracking Discharge of all outputs in Suspend-To-Disk. Table 1. Device summary March 2007 Part number Package Packaging PM6670 VFQFPN-24 4x4 (Exposed Pad) Tube Rev 1 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1/53 www.st.com 53 Contents PM6670 Contents 1 Typical application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 2.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1 7.2 7.3 2/53 VDDQ section - constant On-Time PWM controller . . . . . . . . . . . . . . . . . 20 7.1.1 Constant-On-Time architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.1.2 Output ripple compensation and loop stability . . . . . . . . . . . . . . . . . . . . 23 7.1.3 Pulse-Skip and No-Audible Pulse-Skip Modes . . . . . . . . . . . . . . . . . . . 27 7.1.4 Mode-of-operation selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.1.5 Current sensing and current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.1.6 POR, UVLO and Soft Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.1.7 Power-Good signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.1.8 VDDQ output discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.1.9 Gate drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.1.10 Reference voltage and bandgap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.1.11 Over Voltage and Under Voltage Protections . . . . . . . . . . . . . . . . . . . . 35 7.1.12 Device thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 VTTREF buffered reference and VTT LDO section . . . . . . . . . . . . . . . . . 36 7.2.1 VTT and VTTREF Soft-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.2.2 VTTREF and VTT outputs discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 S3 and S5 power management pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 PM6670 8 Contents Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.1 External components selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.1.1 Inductor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.1.2 Input capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 8.1.3 Output capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.1.4 MOSFETs selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8.1.5 Diode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.1.6 VDDQ current limit setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.1.7 All ceramic capacitors application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3/53 Typical application circuit PM6670 1 Typical application circuit Figure 1. Application circuit R +5V LP VIN C C IN2 IN3 R1 C IN R2 C 22 BOOT 8 VCC 18 VOSC MODE 6 AVCC SEL 11 12 DSCG 3 VDDQ (LDO input) 23 IN4 PHASE LDOIN 4 VTTREF 2 OUT3 24 VTT VTTREF LGATE PM6670 VTTSNS CSNS L 20 VDDQ 17 C OUT 19 VTT PGND 16 VTTGND VSNS 9 5 C 14 13 7 COMP VREF S5 S3 PG 15 R LIM C 10 OUT2 C 4/53 21 1 SGND C C BOOT HGATE BYP INT PM6670 Pin settings 2 Pin settings 2.1 Connections 24 CSNS PHASE HGATE BOOT LDOIN VTT Pin connection (through top view) 19 1 18 VTTGND VCC VTTSNS LGATE DDRSEL PGND PM6670 VTTREF PG SGND 6 13 S5 COMP MODE VSNS DSCG 12 7 VOSC AVCC S3 VREF Figure 2. 5/53 Pin settings 2.2 PM6670 Pin description Table 2. Pin functions N° Pin Function 1 VTTGND LDO Power Ground. Connect to negative terminal of VTT output capacitor. 2 VTTSNS LDO Remote Sensing. Connect as close as possible to the load via a low noise PCB trace. 3 DDRSEL DDR Voltage Selector (if MODE is tied to VCC) or Pulse-Skip/No-Audible Pulse-Skip Selector in Adjustable Mode (MODE voltage lower than 3V). See Section 7.1.4: Mode-of-operation selection on page 29. 4 VTTREF Low Noise Buffered DDR Reference Voltage. A 22nF (minimum) ceramic bypass capacitor is required in order to achieve stability. 5 SGND Ground Reference for analog circuitry, control logic and VTTREF buffer. Connect together with the thermal pad and VTTGND to a low impedance ground plane. See the Application Note for details. 6 AVCC +5V Supply for internal logic. Connect to +5V rail through a simple RC filtering network. 7 VREF High accuracy output Voltage Reference (1.237V) for multilevel pins setting. It can deliver up to 50µA. Connect a 100nF capacitor between VREF and SGND in order to enhance noise rejection. 8 VOSC Frequency Selection. Connect to the central tap of a resistor divider to set the desired switching frequency. The pin cannot be left floating. See Section 7: Device description on page 19 VSNS VDDQ Output Remote Sensing. Discharge path for VDDQ in Non-Tracking Discharge. Input for internal resistor divider that provides VDDQ/2 to VTTREF and VTT. Connect as close as possible to the load via a low noise PCB trace. 10 MODE Mode of operation selector. If MODE pin voltage is higher than 4V, the fixed output mode is selected. If MODE pin voltage is lower than 4V, it is used as negative input of the error amplifier. See Section 7.1.4: Mode-of-operation selection on page 29. 11 COMP DC Voltage Error Compensation Input for the switching section. Refer Section 7.1.4: Mode-of-operation selection on page 29. 12 DSCG Discharge Mode Selection. Refer to Section 7.1.8: VDDQ output discharge on page 33 for Tracking/Non-tracking Discharge or No-Discharge options. 13 S5 Switching Controller Enable. Connect to S5 system status signal to meet S0-S5 power management states compliance. See Section : Power management section on page 12 14 S3 Linear Regulator Enable. Connect to S3 system status signal to meet S0-S5 power management states compliance. See Section : Power management section on page 12 15 PG Power-Good Signal (open drain output). High when VDDQ output voltage is within ±10% of nominal value. 16 PGND Power Ground for the switching section. 17 LGATE Low-side Gate Driver Output. 9 6/53 PM6670 Pin settings Table 2. Pin functions (continued) N° Pin Function 18 VCC +5V Low-side Gate Driver Supply. Bypass with a 100nF capacitor to PGND. 19 CSNS Current Sense Input for the switching section. This pin must be connected through a resistor to the drain of the synchronous rectifier (RDSon sensing) to set the current limit threshold. 20 PHASE Switch Node Connection and return path for the High-side Gate Driver. 21 HGATE High-side Gate Driver Output 22 BOOT Bootstrap Capacitor Connection. Positive Supply Input of the High-side Gate Driver. 23 LDOIN Linear Regulator Input. Connect to VDDQ in normal configuration or to a lower supply to reduce the power dissipation. A 10µF bypass ceramic capacitor is suggested for noise rejection enhancement. See Section 7: Device description on page 19 24 VTT LDO Linear Regulator Output. Bypass with a 20µF (2x10µF MLCC) filter capacitor. 7/53 Electrical data PM6670 3 Electrical data 3.1 Maximum rating Table 3. Absolute maximum ratings (1) Symbol Parameter Value VAVCC AVCC to SGND -0.3 to 6 VVCC VCC to SGND -0.3 to 6 PGND, VTTGND to SGND VPHASE PTOT Unit -0.3 to 0.3 HGATE and BOOT to PHASE -0.3 to 6 HGATE and BOOT to PGND -0.3 to 42 PHASE to SGND -0.3 to 36 LGATE to PGND -0.3 to VCC +0.3 V CSNS, PG, S3, S5, DSCG, COMP, VSNS, VOSC, VREF, MODE, DDRSEL to GND -0.3 to VAVCC + 0.3 VTTREF, VREF, VTT, VTTSNS to SGND -0.3 to VAVCC + 0.3 LDOIN, VTT, VTTREF, LDOIN to VTTGND -0.3 to VAVCC + 0.3 Power dissipation @TA = 25°C 2.3 W 1. Free air operating conditions unless otherwise specified. Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. 3.2 Thermal data Table 4. Thermal data Symbol 3.3 Parameter Value Unit 42 °C/W RthJA Thermal resistance junction to ambient TSTG Storage temperature range -40 to 150 °C TA Operating ambient temperature range -40 to 85 °C TJ Junction operating temperature range 0 to 125 °C Recommended operating conditions Table 5. Recommended operating conditions Values Symbol Parameter Unit Min Max Input voltage range 4.5 28 VAVCC IC supply voltage 4.5 5.5 VVCC IC supply voltage 4.5 5.5 VIN 8/53 Typ V PM6670 4 Electrical characteristics Electrical characteristics TA = 0°C to 85°C , VCC = AVCC = +5V and LDOIN connected to VDDQ output if not otherwise specified. Table 6. Electrical characteristics Values Symbol Parameter Test condition Unit Min Typ Max 0.8 2 Supply section Operating current S3, S5, MODE and DDRSEL connected to AVCC, No Load on VTT and VTTREF Outputs. VCC connected to AVCC ISTR Operating current in STR S5, MODE and DDRSEL connected to AVCC, S3 tied to SGND, No Load on VTTREF. VCC connected to AVCC ISH Operating current in shutdown S3 and S5 tied to SGND. Discharge Mode active. VCC connected to AVCC IIN mA AVCC under voltage lockout upper threshold 4.1 0.6 1 1 10 4.25 4.4 µA V UVLO AVCC under voltage lockout lower threshold 3.9 UVLO hysteresis 70 4.0 4.1 mV ON-time (SMPS) tON On-time duration MODE and DDRSEL high, VVSNS = 2V VOSC = 300mV 650 750 850 VOSC = 500mV 390 450 510 300 350 ns 1.237 1.249 V 4 mV ns OFF-time (SMPS) tOFFMIN Minimum Off time Voltage reference Voltage accuracy 4.5V < VIN < 25V Load regulation -50µA< IVREF < 50µA Undervoltage lockout fault threshold 1.224 -4 800 9/53 Electrical characteristics PM6670 Table 6. Electrical characteristics (continued) Values Symbol Parameter Test condition Unit Min Typ Max VDDQ output VDDQ output voltage, DDR3 VVDDQ VDDQ output voltage, DDR2 Feedback Accuracy MODE connected to AVCC, DDRSEL tied to SGND, No Load MODE and DDRSEL connected to AVCC, No Load 1.5 V 1.8 -1.5 1.5 % 110 µA 5 mV Current limit and zero crossing comparator ICSNS CSNS input bias current 90 Comparator offset -5 Positive current limit threshold Rsense = 1kΩ VPGND - VCSNS Fixed negative current limit threshold VZC,OFFS Zero crossing comparator offset -10 100 -100 mV 110 mV -5 0 HGATE high state (pull-up) 2.0 3 HGATE low state (pull-down) 1.8 2.7 LGATE high state (pull-up) 1.4 2.1 LGATE low state (pull-down) 0.6 0.9 mV High and low side gate drivers HGATE driver on-resistance Ω LGATE driver on-resistance UVP/OVP protections and PGOOD SIGNAL (SMPS only) OVP Over voltage threshold 112 115 118 UVP Under voltage threshold 67 70 73 Power-good upper threshold 107 110 113 Power-good lower threshold 86 90 93 % PGOOD IPG,LEAK PG leakage current PG forced to 5V VPG,LOW PG low-level voltage IPG,SINK = 4mA 1 µA 150 250 mV 3 4 ms Soft start section (SMPS) Soft-start ramp time (4 steps current limit) Soft-start current limit step 10/53 2 25 µA PM6670 Electrical characteristics Table 6. Electrical characteristics (continued) Values Symbol Parameter Test condition Unit Min Typ Max VDDQ Discharge resistance in non-tracking discharge mode 15 25 35 VTT discharge resistance in non-tracking discharge mode 15 25 35 VTTREF discharge resistance in non-tracking discharge mode 1 1.5 2 kΩ 0.2 0.4 0.6 V 1 10 Soft end section Ω VDDQ Output threshold synchronous for final tracking to non-tracking discharge transition VTT LDO section ILDOIN,ON ILDOIN, STR ILDOIN, STD IVTTSNS, LDO input bias current in full-on state S3 = S5 = +5V, No Load on VTT LDO input bias current in suspend-to-RAM state S3 = 0V, S5 = +5V, No Load on VTT 10 LDO input bias current in suspend-to-disk state S3 = S5 = 0V, No Load on VTT 1 VTTSNS bias current S3 = +5V, S5 = +5V, VVTTSNS = VVSNS /2 1 VTTSNS leakage current S3 = 0V, S5 = +5V, VVTTSNS = VVSNS /2 1 BIAS IVTTSNS, LEAK IVTT,LEAK VTT leakage current S3 = 0V, S5 = +5V, VVTT = VVSNS /2 µA -10 10 LDO linear regulator output voltage (DDR2) S3 = S5= +5V, IVTT = 0A, MODE = DDRSEL = +5V 0.9 LDO linear regulator output voltage (DDR3) S3 = S5= +5V, IVTT = 0A, MODE = +5V, DDRSEL = 0V 0.75 V S3 = S5 = MODE = + 5V, -1mA < IVTT < 1mA -20 20 LDO output accuracy respect S3 = S5 = MODE = +5V, -1A < IVTT < 1A to VTTREF -25 25 S3 = S5 = MODE = +5V, -2A < IVTT < 2A -35 35 VVTT < 1.10*( VVSNS /2) 2 2.3 2.8 VVTT > 1.10*( VVSNS /2) 1 1.15 1.4 VVTT > 0.90*( VVSNS /2) -2.8 -2.3 -2 VVTT < 0.90*( VVSNS /2) -1.4 -1.15 -1 VVTT LDO source current limit IVTT,CL LDO sink current limit mV A 11/53 Electrical characteristics PM6670 Table 6. Electrical characteristics (continued) Values Symbol Parameter Test condition Unit Min Typ Max VTTREF section VTTREF output voltage IVTTREF = 0A, VVSNS = 1.8V VVTTREF VTTREF output voltage accuracy respect to VSNS/2 -15mA < IVTTREF < 15mA, VVSNS = 1.8V IVTTREF VTTREF= 0 or VSNS VTTREF current limit 0.9 -2 V 2 ±40 % mA Power management section Turn OFF level 0.4 S3,S5 Turn ON level 1.6 MODE pin high level threshold (1) VMODE VAVCC -0.7 MODE pin low level threshold (1) VAVCC 1.3 DDRSEL pin high level threshold (1) VDDRSEL VAVCC -0.8 DDRSEL pin middle level window (1) VAVCC - 1.0 1.5 DDRSEL pin low level threshold (1) 0.5 DSCG pin high level threshold (1) VDSCG VAVCC -0.8 DSCG pin middle level window (1) 1.0 2.0 DSCG pin low level threshold (1) 0.5 IIN,LEAK Logic inputs leakage current S3, S5 = 5V 10 IIN3,LEAK Multilevel inputs leakage current MODE, DDRSEL and DSCG = 5V 10 VOSC input leakage current VOSC = 500mV 1 IOSC, V µA LEAK Thermal shutdown TSHDN Shutdown temperature (1) 1. Guaranteed by design. Not production tested. 12/53 150 °C PM6670 Typical operating characteristics 5 Typical operating characteristics Figure 3. Efficiency vs load - 1.5V and 1.8V, VIN =12V Figure 4. 100 Swiching frequency (kHz) 90 Efficiency (%) 80 70 60 50 40 DDR2 - Forced PWM DDR2 - No-Audible P-S DDR2 - Pulse-Skip DDR3 - Forced PWM 30 20 DDR3 - No-Audible P-S DDR3 - Pulse-Skip 10 0 0.001 0.01 0.1 1 10 Output current (A) Figure 5. 500 450 400 350 300 250 200 150 100 50 0 0.001 Forced PWM No-Audible P-S Pulse-Skip 0.01 0.1 Switching frequency vs input voltage, 1.8V Figure 6. 10 Switching frequency vs input voltage, 1.5V p g 500 450 450 Switching frequency (kHz) 400 350 300 250 200 400 350 300 250 200 150 0.0 5.0 10.0 15.0 20.0 25.0 30.0 150 0.0 5.0 10.0 Input voltage (V) Figure 7. 15.0 20.0 25.0 30.0 Input voltage (V) VDDQ line regulation, 1.8V, 7A Figure 8. 1.8000 VDDQ line regulation, 1.8V, 7A 1.4980 1.4975 1.7990 1.7980 Output voltage (V) Forced PWM Output voltage (V) 1 Output current (A) 500 Switching frequency (kHz) Switching frequency vs load - 1.8V, VIN = 12V No-Audible P-S Pulse-Skip 1.7970 1.7960 Forced PWM 1.4970 No-Audible P-S 1.4965 Pulse-Skip 1.4960 1.4955 1.4950 1.7950 1.4945 1.7940 0.0 5.0 10.0 15.0 Input voltage (V) 20.0 25.0 30.0 1.4940 0.0 5.0 10.0 15.0 20.0 25.0 30.0 Input voltage (V) 13/53 Typical operating characteristics Figure 9. PM6670 VDDQ load regulation, 1.8V, VIN=12V Figure 10. VDDQ load regulation, 1.5V, VIN=12V 1.530 Forced PWM No-Audible P-S Pulse-Skip 1.850 1.840 Output voltage (V) Output voltage (V) 1.860 1.830 1.820 1.810 Forced PWM No-Audible P-S Pulse-Skip 1.520 1.510 1.500 1.490 1.480 1.470 1.800 0.001 0.01 0.1 1 0.001 10 0.01 Output current (A) 0.940 0.790 0.930 0.780 0.920 0.910 0.900 0.890 0.880 -2.5 10 0.770 0.760 0.750 0.740 -1.5 -0.5 0.5 1.5 Output current (A) Figure 13. VTTREF load regulation, 0.9V, VSNS = 1.8V 14/53 1 Figure 12. VTT load regulation, 0.75V, LDOIN = 1.5V Output voltage (V) Output voltage (V) Figure 11. VTT load regulation, 0.9V, LDOIN = 1.8V 0.1 Output current (A) 2.5 0.730 -2.5 -1.5 -0.5 0.5 1.5 2.5 Output current (A) Figure 14. No-audible pulse-skip waveforms PM6670 Typical operating characteristics Figure 15. Power-up sequence - AVCC above UVLO Figure 16. VDDQ soft-start, 1.8V, heavy load Figure 17. -1.8A to 1.8A VTT load transient, 0.9V Figure 18. 0mA to 9mA VTTREF load transient, 0.9V 15/53 Typical operating characteristics PM6670 Figure 19. Non-tracking (soft) discharge Figure 20. Tracking (fast) discharge, LDOIN = VDDQ Figure 21. 0A to 10A VDDQ load transient, PWM Figure 22. 10A to 0A VDDQ load transient, PWM 16/53 PM6670 Typical operating characteristics Figure 23. 0A to 10A VDDQ load transient, pulse-skip Figure 24. 10A to 0A VDDQ load transient, pulse-skip Figure 25. Over-voltage protection, VDDQ = 1.8V Figure 26. Under-voltage protection, VDDQ = 1.8V 17/53 Block diagram 6 PM6670 Block diagram Figure 27. Functional and block diagram VOSC VREF Vr = 0.9V 1.236V Bandgap BOOT VTTSNS Level shifter Ton HGATE 1-shot LDOIN PHASE Ton min 1-shot VTT Anti Cross Conduction VCC Toff min 1-shot TD LGATE NTD PGND HIZ VTTGND Zero Crossing & Current Limit _ BEN R VTTREF VREF COMP + SWEN gm UVP/OVP SGND AVCC Vr +10% R NTD CSNS - + - Vr + PG + - Vr Vr -10% UVLO SWEN TD NTD BEN HIZ VSNS DDR3 DDRSEL NTD Thermal Shutdown CONTROL LOGIC DSCG adj S3 S5 MODE Table 7. Legend SWEN Switching controller enable TD Tracking discharge enable NTD 18/53 Non-tracking discharge enable BEN VTTREF buffer enable HIZ LDO high impedance mode enable fix PM6670 7 Device description Device description The PM6670 is designed to satisfy DDR2-3 power supply requirements combining a synchronous buck controller, a 15mA buffered reference and a high-current Low-Drop Out (LDO) linear regulator capable of sourcing and sinking up to 2Apk. The switching controller section is a high-performance, pseudo-fixed frequency, Constant-On-Time (COT) based regulator specifically designed for handling fast load transient over a wide range of input voltages. The DDR2-3 supply voltage VDDQ can be easily set to 1.8V (DDR2) or 1.5V (DDR3) without additional components. The output voltage can also be adjusted in the 0.9V to 2.6V range using an external resistor divider. The Switching Mode Power Supply (SMPS) can handle different modes of operation in order to minimize noise or power consumption, depending on the application needs. A lossless current sensing scheme, based on the Low-Side MOSFET’s on resistance avoids the need for an external current sense resistor. The output of the linear regulator (VTT) tracks the memory’s reference voltage VTTREF within ±30mV over the full operating load conditions. The input of the LDO can be either VDDQ or a lower voltage rail in order to reduce the total power dissipation. Linear regulator stability is achieved by filtering its output with a ceramic capacitor (20µF or greater). The reference voltage (VTTREF) section provides a voltage equal to one half of VSNS with an accuracy of 1%. This regulator can source and sink up to ±15mA. A 10nF to 100nF bypass capacitor is required between VTTREF and SGND for stability. According to DDR2/3 JEDEC specifications, when the system enters the Suspend-To-RAM state the LDO output is left in high impedance while VTTREF and VDDQ are still alive. When the Suspend-To-Disk state (S3 and S5 tied to ground) is entered, all outputs are actively discharged when either tracking or non-tracking discharge is selected. 19/53 Device description 7.1 PM6670 VDDQ section - constant On-Time PWM controller The PM6670 uses a pseudo-fixed frequency, Constant On-Time (COT) controller as the core of the switching section. It is well known that the COT controller uses a relatively simple algorithm and uses the ripple voltage derived across the output capacitor’s ESR to trigger the On-Time one-shot generator. In this way, the output capacitor’s ESR acts as a current sense resistor providing the appropriate ramp signal to the PWM comparator. Nearly constant switching frequency is achieved by the system’s loop in steady-state operating conditions by varying the On-Time duration, avoiding thus the need for a clock generator. The On-Time one shot duration is directly proportional to the output voltage, sensed at VSNS pin, and inversely proportional to the input voltage, sensed at the VOSC pin, as follows: Equation 1 TON = K OSC VSNS +τ VOSC where KOSC is a constant value (130ns typ.) and τ is the internal propagation delay (40ns typ.). The one-shot generator directly drives the high-side MOSFET at the beginning of each switching cycle allowing the inductor current to increase; after the On-Time has expired, an Off-Time phase, in which the low-side MOSFET is turned on, follows. The OffTime duration is solely determined by the output voltage: when lower than the set value (i.e. the voltage at VSNS pin is lower than the internal reference VR = 0.9V), the synchronous rectifier is turned off and a new cycle begins (Figure 28). Figure 28. Inductor current and output voltage in steady state conditions Inductor current Output voltage Vreg Ton 20/53 Toff t PM6670 Device description The duty-cycle of the buck converter is, in steady-state conditions, given by Equation 2 V OUT D = -------------V IN The switching frequency is thus calculated as Equation 3 fSW VOUT α VIN D 1 = = = OSC ⋅ V TON α OUT K OSC K OSC SNS VOSC where Equation 4a V OSC α OSC = -------------V IN Equation 4b V SNS α OUT = -------------V OUT Referring to the typical application schematic (figures on cover page and Figure 29), the final expression is then: Equation 5 fSW = α OSC R2 1 = ⋅ K OSC R1 + R 2 K OSC Even if the switching frequency is theoretically independent from battery and output voltages, parasitic parameters involved in power path (like MOSFETs' on-resistance and inductor's DCR) introduce voltage drops responsible for slight dependence on load current. In addition, the internal delay is due to a small dependence on input voltage. The PM6670 switching frequency can be set by an external divider connected to the VOSC pin. Figure 29. Switching frequency selection and VOSC pin VIN PM6670 R1 VOSC R2 The voltage seen at this pin must be greater than 0.8V and lower than 2V in order to ensure the system's linearity. 21/53 Device description 7.1.1 PM6670 Constant-On-Time architecture Figure 30 shows the simplified block diagram of the Constant-On-Time controller. The switching regulator of the PM6670 owns a one-shot generator that ignites the high-side MOSFET when the following conditions are simultaneously satisfied: the PWM comparator is high (i.e. output voltage is lower than Vr = 0.9V), the synchronous rectifier current is below the current limit threshold and the minimum off-time has expired. A minimum Off-Time constraint (300ns typ.) is introduced to assure the boot capacitor charge and allow inductor valley current sensing on low-side MOSFET. A minimum On-Time is also introduced to assure the start-up switching sequence. Once the On-Time has timed out, the high side switch is turned off, while the synchronous rectifier is ignited according to the anti-cross conduction management circuitry. When the output voltage reaches the valley limit (determined by internal reference Vr = 0.9V), the low-side MOSFET is turned off according to the anti-cross conduction logic once again, and a new cycle begins. Figure 30. Switching section simplified block diagram VOSC CSNS BOOT VOSC Positive Current Limit comparator ToffToff-min + Level shifter - 100uA PHASE + S Q - COMP PWM Comparator R gm Anti crossconduction circuitry Q + - - + + TonTon-min 0.9V 2.5V 500mV VCC MODE<4V MODE + - Ton 2.5V S VSNS S DDRSEL Q VOSC LS driver Q VSNS Min fsw counter R Q 0.9V VBG bandgap 1.236V + ZeroZero-crossing Comparator _ PULSE - SKIP SGND LGATE PGND R 22/53 HGATE 1-Shot generator VBG Integrator HS driver VREF PM6670 7.1.2 Device description Output ripple compensation and loop stability The loop is closed connecting the center tap of the output divider (internally, when the fixed output voltage is chosen, or externally, using the MODE pin in the adjustable output voltage mode). The feedback node is the negative input of the error comparator, while the positive input is internally connected to the reference voltage (Vr = 0.9V). When the feedback voltage becomes lower than the reference voltage, the PWM comparator goes to high and sets the control logic, turning on the high-side MOSFET. After the On-Time (calculated as previously described) the system releases the high-side MOSFET and turns on the synchronous rectifier. The voltage drop along ground and supply PCB paths, used to connect the output capacitor to the load, is a source of DC error. Furthermore the system regulates the output voltage valley, not the average, as shown in Figure 28. Thus, the voltage ripple on the output capacitor is an additional source of DC error. To compensate this error, an integrative network is introduced in the control loop, by connecting the output voltage to the COMP pin through a capacitor (CINT) as shown in Figure 31. Figure 31. Circuitry for output ripple compensation COMP PIN VOLTAGE ∆V Vr VREF t COMP OUTPUT VOLTAGE I=gm(V1-Vr) + - PWM Comparator CFILT gm ∆V CINT RINT t + VCINT Vr RFb1 V1 RFb2 ESR VSNS COUT The additional capacitor is used to reduce the voltage on the COMP pin when higher than 300mVpp and is unnecessary for most of applications. The trans conductance amplifier (gm) generates a current, proportional to the DC error, used to charge the CINT capacitor. The voltage across the CINT capacitor feeds the negative input of the PWM comparator, forcing the loop to compensate the total static error. An internal voltage clamp forces the COMP pin voltage range to ±150mV with respect to VREF. This is useful to avoid or smooth output voltage overshoot during a load transient. When the Pulse-Skip Mode is entered, the clamping range is automatically reduced to 60mV in order to enhance the recovering capability. In the ripple amplitude is larger than 150mV, an additional capacitor CFILT can be connected between the COMP pin and ground to reduce ripple amplitude, otherwise the integrator will operate out of its linearity range. This capacitor is unnecessary for most of applications and can be omitted. 23/53 Device description PM6670 The design of the external feedback network depends on the output voltage ripple. If the ripple is higher than approximately 20mV, the correct CINT capacitor is usually enough to keep the loop stable. The stability of the system depends firstly on the output capacitor zero frequency. The following condition must be satisfied: Equation 6 fSW > k ⋅ fZout = k 2π ⋅ C out ⋅ ESR where k is a fixed design parameter (k > 3). It determines the minimum integrator capacitor value: Equation 7 CINT > gm Vr ⋅ ⎛ fSW ⎞ Vout 2π ⋅ ⎜ − fZout ⎟ ⎝ k ⎠ where gm = 50µs is the integrator trans conductance. In order to ensure stability it must be also verified that: Equation 8 CINT > gm Vr ⋅ 2π ⋅ fZout VOUT If the ripple on the COMP pin is greater than the integrator 150mV, the auxiliary capacitor CFILT can be added. If q is the desired attenuation factor of the output ripple, CFILT is given by: Equation 9 CFILT = CINT ⋅ (1 − q) q In order to reduce the noise on the COMP pin, it is possible to add a resistor RINT that, together with CINT and CFILT, becomes a low pass filter. The cutoff frequency fCUT must be much greater (10 or more times) than the switching frequency: Equation 10 RINT = 2π ⋅ fCUT 1 C ⋅C ⋅ INT FILT CINT + CFILT If the ripple is very small (lower than approximately 20mV), a different compensation network, called "Virtual-ESR" Network, is needed. This additional circuit generates a triangular ripple that is added to the output voltage ripple at the input of the integrator. The complete control scheme is shown in Figure 32. 24/53 PM6670 Device description Figure 32. "Virtual-ESR" Network COMP PIN VOLTAGE T NODE VOLTAGE ∆V2 VREF ∆V1 t VREF t COMP I=gm(V1-Vr) - PWM Comparator RINT CINT CFILT gm R1 Vr C VSNS OUTPUT VOLTAGE ∆V + - T R + RFb1 V1 RFb2 ESR COUT t The ripple on the COMP pin is the sum of the output voltage ripple and the triangular ripple generated by the Virtual-ESR Network. In fact the Virtual-ESR Network behaves like a another equivalent series resistor RVESR. A good trade-off is to design the network in order to achieve an RVESR given by: Equation 11 R VESR = VRIPPLE − ESR ∆IL where ∆IL is the inductor current ripple and VRIPPLE is the total ripple at the T node, chosen greater than approximately 20mV. The new closed-loop gain depends on CINT. In order to ensure stability it must be verified that: Equation 12 CINT > gm Vr ⋅ 2π ⋅ fZ Vout where: Equation 13 fZ = 1 2π ⋅ C out ⋅ R TOT and: 25/53 Device description PM6670 Equation 14 RTOT = ESR + RVESR Moreover, the CINT capacitor must meet the following condition: Equation 15 fSW > k ⋅ fZ = k 2π ⋅ C out ⋅ R TOT where RTOT is the sum of the ESR of the output capacitor and the equivalent ESR given by the Virtual-ESR Network (RVESR). The k parameter must be greater than unity (k > 3) and determines the minimum integrator capacitor value CINT: Equation 16 CINT > gm Vr ⋅ ⎛ fSW ⎞ Vout 2π ⋅ ⎜ − fZ ⎟ ⎝ k ⎠ The capacitor of the Virtual-ESR Network, C, is chosen as follows: Equation 17 C > 5 ⋅ CINT and R is calculated to provide the desired triangular ripple voltage: Equation 18 R= L R VESR ⋅ C Finally the R1 resistor is calculated according to expression 19: Equation 19 ⎛ 1 ⎞ ⎟ R ⋅ ⎜⎜ ⋅ π ⋅ fZ ⎟⎠ C ⎝ R1 = 1 R− C ⋅ π ⋅ fZ 26/53 PM6670 7.1.3 Device description Pulse-Skip and No-Audible Pulse-Skip Modes High efficiency at light load conditions is achieved by PM6670 entering the Pulse-Skip Mode (if enabled). When one of the two fixed output voltages is set, Pulse-Skip power saving is a default feature. At light load conditions the zero-crossing comparator truncates the low-side switch On-Time as soon as the inductor current becomes negative; in this way the comparator determines the On-Time duration instead of the output ripple (see Figure 33). Figure 33. Inductor current and output voltage at light load with Pulse-Skip Inductor current VDDQ Output Vreg TON TOFF t TIDLE As a consequence, the output capacitor is left floating and its discharge depends solely on the current drained from the load. When the output ripple on the pin COMP falls under the reference, a new shot is triggered and the next cycle begins. The Pulse-Skip mode is naturally obtained enabling the zero-crossing comparator and automatically takes part in the C.O.T. algorithm when the inductor current is about half the ripple current amount, i.e. migrating from continuous conduction mode (C.C.M.) to discontinuous conduction mode (D.C.M.). The output current threshold related to the transition between PWM Mode and Pulse-Skip Mode can be approximately calculated as: Equation 20 ILOAD (PWM2Skip) = VIN − VOUT ⋅ TON 2 ⋅L At higher loads, the inductor current never crosses zero and the device works in pure PWM mode with a switching frequency around the nominal value. A physiological consequence of Pulse-Skip Mode is a more noisy and asynchronous (than normal conditions) output, mainly due to very low load. If the Pulse-Skip is not compatible with the application, the PM6670, when set in adjustable mode-of-operation, allows the user to choose between forced-PWM and No-Audible Pulse-Skip alternative modes (see 4.1.4 for details). 27/53 Device description PM6670 No-Audible Pulse-Skip Mode Some audio-noise sensitive applications cannot accept the switching frequency to enter the audible range as is possible in Pulse-Skip mode with very light loads. For this reason, the PM6670 implements an additional feature to maintain a minimum switching frequency of 33kHz despite a slight efficiency loss. At very light load conditions, if any switching cycle has taken place within 30µs (typ.) since the last one (because the output voltage is still higher than the reference), a No-Audible Pulse-Skip cycle begins. The low-side MOSFET is turned on and the output is driven to fall until the reference has been crossed. Then, the high-side switch is turned on for a TON period and, once it has expired, the synchronous rectifier is enabled until the inductor current reaches the zero-crossing threshold (see Figure 34). Figure 34. Inductor current and output voltage at light load with non-audible pulse-skip Inductor current VDDQ Output Vreg TMAX TON TOFF TIDLE t For frequencies higher than 33kHz (due to heavier loads) the device works in the same way as in Pulse-Skip mode. It is important to notice that in both Pulse-Skip and No-Audible Pulse-Skip modes the switching frequency changes not only with the load but also with the input voltage. 28/53 PM6670 7.1.4 Device description Mode-of-operation selection Figure 35. MODE and DDRSEL multifunction pin configurations VDDQ VDDQ +5V +5V PM6670 R9 PM6670 R9 MODE MODE R8 R8 VREF DDRSEL DDRSEL (a) (b) The PM6670 has been designed to satisfy the widest range of applications involving DDR2/3 memories, SSTL15-18 buses termination and I/O supplies for CPU/Chipset. The device is provided with multilevel pins which allow the user to choose the appropriate configuration. The MODE pin is used to firstly decide between fixed preset or adjustable (user defined) output voltages. When the MODE pin is connected to +5V, the PM6670 allows setting the VDDQ voltage to 1.8V or 1.5V just forcing the DDRSEL multilevel pin to +5V or to ground respectively (see Figure 35a). In this condition the Pulse-Skip feature is enabled. This device configuration is suitable for standard DDR2/3 memory supply applications avoiding the need for an external, high accuracy, divider for output voltage setting. Applications requiring different output voltages can be managed by PM6670 simply setting the adjustable mode. If MODE pin voltage is higher than 4V, the fixed output mode is selected. Connecting an external divider to the MODE pin (Figure 35b), it is used as negative input of the error amplifier and the output voltage is given by expression (21). Equation 21 VDDQ ADJ = 0.9 ⋅ R8 + R9 R8 29/53 Device description PM6670 VDDQ output voltage can be set in the range from 0.9V to 2.6V. Adjustable mode automatically switches DDRSEL pin to become the power saving algorithm selector: if tied to +5V, the forced-PWM (fixed frequency) control is performed. If grounded or connected to VREF pin (1.237V reference voltage), the Pulse-Skip or Non-Audible Pulse-Skip Modes are respectively selected. Table 8. Mode-Of-Operation settings summary Mode VMODE > 4.3V DDRSEL VDDQ VDDRSEL > 4.2V 1.8V 1V < VDDRSEL < 3.5V Operating mode Pulse-Skip 1.5V <0.5V VDDRSEL > 4.2V VMODE < 3.7V 1V < VDDRSEL < 3.5V Forced-PWM ADJ Non-Audible Pulse-skip VDDRSEL < 0.5V 7.1.5 Pulse-Skip Current sensing and current limit The PM6670 switching controller uses a valley current sensing algorithm to properly handle the current limit protection and the inductor current zero-crossing information. The current is sensed during the conduction time of the low-side MOSFET. The current sensing element is the on-resistance of the low-side switch. The sensing scheme is visible in Figure 36. Figure 36. Current sensing scheme VIN PM6670 HGATE VOUT PHASE CSNS 100µA·RILIM IVALLEY·RDSon LGATE PGND An internal 100µA current source is connected to CSNS pin that is also the non-inverting input of the positive current limit comparator. When the voltage drop developed across the sensing parameter equals the voltage drop across the programming resistor RILIM, the controller skips subsequent cycles until the overcurrent condition is detected or the output UV protection latches off the device (see Section 7.1.11: Over Voltage and Under Voltage Protections on page 35 ). 30/53 PM6670 Device description Referring to Figure 36, the RDSon sensing technique allows high efficiency performance without the need for an external sensing resistor. The on-resistance of the MOSFET is affected by temperature drift and nominal value spread of the parameter itself; this must be considered during the RILIM setting resistor design. It must be taken into account that the current limit circuit actually regulates the inductor valley current. This means that RILIM must be calculated to set a limit threshold given by the maximum DC output current plus half of the inductor ripple current: Equation 22 ICL = 100µA ⋅ RILIM RDSon The PM6670 provides also a fixed negative current limit to prevent excessive reverse inductor current when the switching section sinks current from the load in forced-PWM (3rd quadrant working conditions). This negative current limit threshold is measured between PHASE and PGND pins, comparing the drop magnitude on PHASE pin with an internal 120mV fixed threshold. 7.1.6 POR, UVLO and Soft Start The PM6670 automatically performs an internal startup sequence during the rising phase of the analog supply of the device (AVCC). The switching controller remains in a stand-by state until AVCC crosses the upper UVLO threshold (4.2V typ.), keeping active the internal discharge MOSFETs (only if AVCC > 1V). The soft-start allows a gradual increase of the internal current limit threshold during start-up reducing the input/output surge currents. At the beginning of start-up, the PM6670 current limit is set to 25% of nominal value and the Under Voltage Protection is disabled. Then, the current limit threshold is sequentially brought to 100% in four steps of approximately 750µs (Figure 37). Figure 37. Soft-start waveforms Switching output Current limit threshold S5 Time 31/53 Device description PM6670 After a fixed 3ms total time, the soft-start finishes and UVP is released: if the output voltage doesn't reach the Power-Good lower threshold within soft-start duration, the UVP condition is detected and the device performs a soft end and latches off. Depending on the load conditions, the inductor current may or may not reach the nominal value of the current limit during the soft-start (Figure 38 shows two examples). Figure 38. Soft-start at heavy load (a) and short-circuit (b) conditions, Pulse-Skip enabled (a) 7.1.7 (b) Power-Good signal The PG pin is an open drain output used to monitor output voltage through VSNS (in fixed output voltage mode) or MODE (in adjustable output voltage mode) pins and is enabled after the soft-start timer has expired. PG signal is held low if the VDDQ output voltage drops 10% below or rises 10% above the nominal regulated value. The PG output can sink current up to 4mA. 32/53 PM6670 7.1.8 Device description VDDQ output discharge Active discharge of VDDQ output occurs when PM6670 enters the Suspend-To-Disk system state (S3 and S5 tied to GND) and DSCG pin has been properly set. Figure 39. DSCG pin connection for discharge mode selection +5V PM6670 VREF DSCG The PM6670 allows the user to choose between fast discharge (Tracking Discharge), soft discharge (Non-Tracking Discharge) or no discharge modes. Voltage on DSCG multilevel pin determines discharge mode as shown in Table 2 on page 6. Table 9. Discharge mode selection DSCG voltage Soft-End type Description VDSCG >4.2V No Discharge All outputs left floating. 1V< VDSCG <3.5V Fast (Tracking) VDDQ and VTT actively discharged by LDO trough LDOIN and VTT pins; VDSCG <0.5V Soft (Non-Tracking) All outputs discharged by dedicated internal MOS. Tracking discharge allows the fastest discharge of all outputs but requires the LDOIN to be self-supplied from VDDQ output voltage. When an external supply rail is connected to LDOIN, it must be taken into account to avoid damage to the device. Discharge current (1A) flows through the LDOIN pin until the output has reached approximately 400mV and then a soft discharge completes the process by discharging the output with an internal 22Ω switch. Figure 40. Fast discharge and soft discharge options VDDQ Fast discharge VDDQ Soft discharge VTT Soft discharge VTT 400mV 33/53 Device description 7.1.9 PM6670 Gate drivers The integrated high-current gate drivers allow using different power MOSFETs. The highside driver uses a bootstrap circuit which is supplied by the +5V rail. The BOOT and PHASE pins work respectively as supply and return path for the high-side driver, while the low-side driver is directly fed through VCC and PGND pins. An important feature of the PM6670 gate drivers is the Adaptive Anti-Cross-Conduction circuitry, which prevents high-side and low-side MOSFETs from being turned on at the same time. When the high-side MOSFET is turned off, the voltage at the PHASE node begins to fall. The low-side MOSFET is turned on only when the voltage at the PHASE node reaches an internal threshold (2.5V typ.). Similarly, when the low-side MOSFET is turned off, the high-side one remains off until the LGATE pin voltage is above 1V. The power dissipation of the drivers is a function of the total gate charge of the external power MOSFETs and the switching frequency, as shown in the following equation: Equation 23 PD (driver ) = VDRV ⋅ Q g ⋅ fSW The low-side driver has been designed to have a low-resistance pull-down transistor (0.6Ω typ.) in order to prevent undesired ignition of the low-side MOSFET due to the Miller effect. 7.1.10 Reference voltage and bandgap The 1.237V internal bandgap reference has a granted accuracy of ±1% over the 0°C to 85°C temperature range. The VREF pin is a buffered replica of the bandgap voltage. It can supply up to ±100µA and is suitable to set the intermediate level of MODE, DDRSEL and DSCG multifunction pins. A 100nF (min.) bypass capacitor toward SGND is required to enhance noise rejection. If VREF falls below 0.87V (typ.), the system detects a fault condition and all the circuitry is turned OFF. An internal divider derives a 0.9V±1% voltage (Vr) from the bandgap. This voltage is used as a reference by the switching regulator output. The Over-Voltage Protection, the UnderVoltage Protection and the Power-Good signal are also referred to Vr. 34/53 PM6670 7.1.11 Device description Over Voltage and Under Voltage Protections When the switching output voltage is about 115% of its nominal value, a latched OverVoltage Protection (OVP) occurs. In this case the synchronous rectifier immediately turns on while the high-side MOSFET turns OFF. The output capacitor is rapidly discharged and the load is preserved from being damaged. The OVP is also active during the soft start. Once an OVP has occured, a toggle on S5 pin or a Power-On-Reset is necessary to exit from the latched state. When the switching output voltage is below 70% of its nominal value, a latched UnderVoltage Protection occurs. This event causes the switching section to be immediately disabled and both switches to be opened. The controller enters in Soft-End mode and the output is eventually kept to ground, turning the low side MOSFET on when the voltage is lower than 400mV. If S3 and S5 are forced low, the low-side MOSFET is released and only the 22Ω switch is active. The Under-Voltage Protection circuit is enabled only at the end of the soft-start. Once an UVP has toccured, a toggle on S5 pin or a Power-On-Reset is necessary to clear the fault state and restart the device. 7.1.12 Device thermal protection The internal control circuitry of the PM6670 self-monitors the junction temperature and turns all outputs off when the 150°C limit has been overrun. This event causes the switching section to be immediately disabled and both switches to be opened. The controller enters in Soft-End Mode and the output is eventually kept to ground, turning the low side MOSFET on when the voltage is lower than 400mV. If S3 and S5 are forced low, the low-side switch is released and only the 22Ω discharge MOSFET is active. The thermal fault is a latched protection and normal operating condition is restored by a Power-On Reset or toggling S5. Table 10. OV, UV and OT faults management Fault VDDQ over voltage Conditions Action VDDQ > 115% of the LGATE pin is forced high and the device latches off. nominal value Exit by a Power-On Reset or toggling S5 VDDQ under voltage VDDQ < 70% of the nominal value LGATE pin is forced high after the Soft-End, then the device latches off. Exit by a Power-On Reset or toggling S5. Junction over temperature TJ > +150°C LGATE pin is forced high after the Soft-End, then the device latches off. Exit by a Power-On Reset or toggling S5 after 15°C temperature drop. 35/53 Device description 7.2 PM6670 VTTREF buffered reference and VTT LDO section The PM6670 provides the required DDR2/3 reference voltage on the VTTREF pin. The internal buffer tracks half the voltage on the VSNS pin and has a sink and source capability up to 15mA. Higher currents rapidly deteriorate the output accuracy. A 10nF to 100nF (33nF typ.) bypass capacitor to SGND is required for stability. The VTT Low-Drop-Out linear regulator has been designed to sink and source up to 2A peak current and 1A continuously. The VTT voltage tracks VTTREF within ±35mV. A remote voltage sensing pin (VTTSNS) is provided to recovery voltage drops due to parasitic resistance. In DDR2/3 applications, the linear regulator input LDOIN is typically connected to VDDQ output; connecting LDOIN pin to a lower voltage, if available in the system, reduces the power dissipation of the LDO. A minimum output capacitance of 20µF (2x10µF MLCC capacitors) is enough to assure stability and fast load transient response. 7.2.1 VTT and VTTREF Soft-Start Soft-Start on VTT and VTTREF outputs is achieved by current clamping. The LDO linear regulator is provided with a current foldback protection: when the output voltage exits the internal ±10% VTT-Good window, the output current is clamped at ±1A. Reentering VTT-Good window releases the current limit clamping. The foldback mechanism naturally implements a two steps soft-start charging the output capacitors with a 1A constant current. Something similar occurs at VTTREF pin, where the output capacitor is smoothly charged at a fixed 40mA current limit. 7.2.2 VTTREF and VTT outputs discharge The Tracking Discharge mechanism involves the VTT linear regulator. When the SuspendTo-Disk state is entered, the switching regulator is turned OFF. At the same time the LDO drains a 1A constant current from LDOIN and keeps VTT in track with VTTREF that, in turn, is half the voltage at the VSNS pin. When the VDDQ output reaches 400mV, the PM6670 switches on the internal discharge MOSFETs to complete the process (see Section 7.1.8: VDDQ output discharge on page 33). In Soft Discharge (i.e. Non-Tracking Discharge) the PM6670 disables the internal regulators and suddenly turns on the discharge MOSFETs on each output. 36/53 PM6670 7.3 Device description S3 and S5 power management pins According to DDR2/3 memories supply requirements, the PM6670 can manage all S0 to S5 system states by connecting S3-S5 pins to their respective sleep-mode signals in the notebook's motherboard. Keeping S3 and S5 high, the S0 (Full-On) state is decoded and the outputs are alive. In S3 state (S5 = 1, S3 = 0), the PM6670 maintains VDDQ and VTTREF outputs active and VTT output in high-impedance as needed. In S4/S5 states (S5 = S3 = 0) all outputs are turned off and, according to DSCG pin voltage, the proper Soft-End is performed. Table 11. S3 and S5 Sleep-states decoding S3 S5 System State VDDQ VTTREF VTT 1 1 S0 (Full-On) On On On 0 1 S3 (Suspend-To-RAM) On On Off (Hi-Z) 0 0 S4/S5 (Suspend-To-Disk) Off (Discharge) Off (Discharge) Off (Discharge) 37/53 Application information 8 PM6670 Application information The purpose of this chapter is to show the design procedure of the switching section. The design starts from three main specifications: ● The input voltage range, provided by the battery or the AC adapter. The two extreme values (VINMAX and VINmin ) are important for the design. ● The maximum load current, indicated by ILOAD,MAX. ● The maximum allowed output voltage ripple VRIPPLE,MAX. It's also possible that specific designs should involve other specifications. The following paragraphs will guide the user into a step-by-step design. 8.1 External components selection The PM6670 uses a pseudo-fixed frequency, Constant On-Time (COT) controller as the core of the switching section. The switching frequency can be set by connecting an external divider to the VOSC pin. The voltage seen at this pin must be greater than 0.8V and lower than 2V in order to ensure system's linearity. Nearly constant switching frequency is achieved by the system's loop in steady-state operating conditions by varying the On-Time duration, avoiding thus the need for a clock generator. The On-Time one shot duration is directly proportional to the output voltage, sensed at VSNS pin, and inversely proportional to the input voltage, sensed at the VOSC pin, as follows: Equation 24 TON = K OSC VSNS +τ VOSC where KOSC is a constant value (130ns typ.) and τ is the internal propagation delay (40ns typ.). The duty cycle of the buck converter is, under steady state conditions, given by Equation 25 D= VOUT VIN The switching frequency is thus calculated as Equation 26 fSW 38/53 VOUT α VIN 1 D = = = OSC ⋅ VSNS TON α OUT K OSC K OSC ⋅ VOSC PM6670 Application information where Equation 27a α OSC = VOSC VIN α OUT = VSNS VOUT Equation 27b Referring to the typical application schematic (figure in cover page and Figure 29), the final expression is then: Equation 28 fSW = α OSC R2 1 = ⋅ K OSC R1 + R 2 K OSC The switching frequency directly affects two parameters: ● Inductor size: greater frequencies mean smaller inductances. In notebook applications, real estate solutions (i.e. low-profile power inductors) are mandatory also with high saturation and r.m.s. currents. ● Efficiency: switching losses are proportional to the frequency. Generally, higher frequencies imply lower efficiency. Even if the switching frequency is theoretically independent from battery and output voltages, parasitic parameters involved in power path (like MOSFETs' on-resistance and inductor's DCR) introduce voltage drops responsible for a slight dependence on load current. In addition, the internal delay is due to a light dependence on input voltage. Table 12. Typical values for switching frequency selection R1 (kΩ) R2 (kΩ) Approx switching frequency (kHz) 330 11 250 330 13 300 330 15 350 330 18 400 330 20 450 330 22 500 39/53 Application information 8.1.1 PM6670 Inductor selection Once the switching frequency has been defined, the inductance value depends on the desired inductor ripple current. Low inductance value means great ripple current that brings poor efficiency and great output noise. On the other hand a great current ripple is desirable for fast transient response when a load step is applied. High inductance brings higher efficiency, but the transient response is critical, especially if VINmin - VOUT is small. Moreover a minimum output ripple voltage is necessary to assure system stability and jitter-free operations (see Output capacitor selection paragraph). The product of the output capacitor's ESR multiplied by the inductor ripple current must be taken into consideration. A good trade-off between the transient response time, the efficiency, the cost and the size is choosing the inductance value in order to maintain the inductor ripple current between 20% and 50% (usually 40%) of the maximum output current. The maximum inductor ripple current, ∆IL,MAX , occurs at the maximum input voltage. Given these considerations, the inductance value can be calculated with the following expression: Equation 29 L= VIN − VOUT VOUT ⋅ fsw ⋅ ∆IL VIN where fSW is the switching frequency, VIN is the input voltage, VOUT is the output voltage and ∆IL is the inductor ripple current. Once the inductor value is determined, the inductor ripple current is then recalculated: Equation 30 ∆IL,MAX = VIN,MAX − VOUT fsw ⋅ L ⋅ VOUT VIN,MAX The next step is the calculation of the maximum r.m.s. inductor current: Equation 31 IL,RMS = (ILOAD,MAX )2 + (∆IL,MAX )2 12 The inductor must have an r.m.s. current greater than IL,RMS in order to assure thermal stability. Then the calculation of the maximum inductor peak current follows: Equation 32 IL,PEAK = ILOAD,MAX + ∆IL,MAX 2 IL,PEAK is important in inductor selection in term of its saturation current. 40/53 PM6670 Application information The saturation current of the inductor should be greater than IL,PEAK not only in case of hard saturation core inductors. Using soft-ferrite cores it is possible (but not advisable) to push the inductor working near its saturation current. In Table 13 some inductors suitable for notebook applications are listed. Table 13. Evaluated inductors (@fsw = 400kHz) Manufacturer Series Inductance (ìH) +40°C rms current (A) -30% saturation current (A) COILCRAFT MLC1538-102 1 13.4 21.0 COILCRAFT MLC1240-901 0.9 12.4 24.5 COILCRAFT MVR1261C-112 1.1 20 20 WURTH 7443552100 1 16 20 COILTRONICS HC8-1R2 1.2 16.0 25.4 In Pulse-Skip Mode, low inductance values produce a better efficiency versus load curve, while higher values result in higher full-load efficiency because of the smaller current ripple. 8.1.2 Input capacitor selection In a buck topology converter the current that flows through the input capacitor is pulsed and with zero average value. The RMS input current can be calculated as follows: Equation 33 2 ICinRMS = ILOAD ⋅ D ⋅ (1 − D) + 1 D ⋅ (∆IL )2 12 Neglecting the second term, the equation 10 is reduced to: Equation 34 ICinRMS = ILOAD D ⋅ (1 − D) The losses due to the input capacitor are thus maximized when the duty-cycle is 0.5: Equation 35 Ploss = ESR Cin ⋅ ICinRMS (max)2 = ESR Cin ⋅ (0.5 ⋅ ILOAD (max))2 The input capacitor should be selected with a RMS rated current higher than ICINRMS(max). Tantalum capacitors are good in terms of low ESR and small size, but they occasionally can burn out if subjected to very high current during operation. Multi-Layers-Ceramic-Capacitors (MLCC) have usually a higher RMS current rating with smaller size and they remain the best choice. The drawback is their quite high cost. 41/53 Application information PM6670 It must be taken into account that in some MLCC the capacitance decreases when the operating voltage is near the rated voltage. In Table 14 some MLCC suitable for most of applications are listed. Table 14. Evaluated MLCC for input filtering Manufacturer 8.1.3 Capacitance (µF) Rated Voltage (V) Series Maximum Irms @100kHz (A) TAIYO YUDEN UMK325BJ106KM-T 10 50 2 TAIYO YUDEN GMK316F106ZL-T 10 35 2.2 TAIYO YUDEN GMK325F106ZH-T 10 35 2.2 TAIYO YUDEN GMK325BJ106KN 10 35 2.5 TDK C3225X5R1E106M 10 25 Output capacitor selection Using tantalum or electrolytic capacitors, the selection is made referring to ESR and voltage rating rather than by a specific capacitance value. The output capacitor has to satisfy the output voltage ripple requirements. At a given switching frequency, small inductor values are useful to reduce the size of the choke but increase the inductor current ripple. Thus, to reduce the output voltage ripple a low ESR capacitor is required. To reduce jitter noise between different switching regulators in the system, it is preferable to work with an output voltage ripple greater than 25mV. As far as it concerning the load transient requirements, the Equivalent Series Resistance (ESR) of the output capacitor must satisfy the following relationship: Equation 36 ESR ≤ VRIPPLE,MAX ∆IL,MAX where VRIPPLE is the maximum tolerable ripple voltage. In addition, the ESR must be high enough high to meet stability requirements. The output capacitor zero must be lower than the switching frequency: Equation 37 fSW > fZ = 42/53 1 2π ⋅ ESR ⋅ C out PM6670 Application information If ceramic capacitors are used, the output voltage ripple due to inductor current ripple is negligible. Then the inductance could be smaller, reducing the size of the choke. In this case it is important that output capacitor can adsorb the inductor energy without generating an over-voltage condition when the system changes from a full load to a no load condition. The minimum output capacitance can be chosen by the following equation: Equation 38 COUT,min = L ⋅ ILOAD,MAX Vf 2 − Vi 2 where Vf is the output capacitor voltage after the load transient, while VI is the output capacitor voltage before the load transient. In Table 15 are listed some tested polymer capacitors are listed. Table 15. Evaluated output capacitors Series Capacitance (µF) Rated voltage (V) ESR max @100kHz (mΩ) 4TPE220MF 220 4V 15 to 25 4TPE150MI 220 4V 18 4TPC220M 220 4V 40 TNCB OE227MTRYF 220 2.5V 25 Manufacturer SANYO HITACHI 8.1.4 MOSFETs selection In a notebook application, power management efficiency is a high level requirement. Power dissipation on the power switches becomes animportant factor in the selection of switches. Losses of high-side and low-side MOSFETs depend on their working condition. Considering the high-side MOSFET, the power dissipation is calculated as: Equation 39 PDHighSide = Pconduction + Pswitching Maximum conduction losses are approximately given by: Equation 40 Pconduction = RDSon ⋅ VOUT 2 ⋅ ILOAD,MAX VIN. min 43/53 Application information PM6670 where RDSon is the drain-source on-resistance of the control MOSFET. Switching losses are approximately given by: Equation 41 Pswitching = VIN ⋅ (ILOAD (max) − 2 ∆IL ∆I ) ⋅ t on ⋅ fsw VIN ⋅ (ILOAD (max) + L ) ⋅ t off ⋅ fsw 2 2 + 2 where tON and tOFF are the turn-on and turn-off times of the MOSFET and depend on the gate-driver current capability and the gate charge Qgate. A greater efficiency is achieved with low RDSon. Unfortunately low RDSon MOSFETs have a great gate charge. As general rule, the RDSon x Qgate product should be minimized to find out the suitable MOSFET. Logic-level MOSFETs are recommended, as long as low-side and high-side gate drivers are powered by VVCC = +5V. The breakdown voltage of the MOSFETs (VBRDSS) must be greater than the maximum input voltage .VINmax. Table 15 lists tested high-side MOSFETs. Table 16. Evaluated high-side MOSFETs Manufacturer Type RDSon (mΩ) Gate charge (nC) Rated reverse voltage (V) ST STS12NH3LL 10.5 12 30 IR IRF7811 9 18 30 In buck converters the power dissipation of the synchronous MOSFET is mainly due to conduction losses: Equation 42 PDLowSide ≅ Pconduction Maximum conduction losses occur at the maximum input voltage: Equation 43 ⎛ V Pconduction = RDSon ⋅ ⎜1 − OUT ⎜ V IN,MAX ⎝ ⎞ ⎟ ⋅ ILOAD,MAX 2 ⎟ ⎠ The synchronous rectifier should have the lowest RDSon as possible. When the high-side MOSFET turns on, high dV/dt of the phase node can bring up even the low-side gate through its gate-drain capacitance CRRS, causing a cross-conduction problem. Once again, the choice of the low-side MOSFET is a trade-off between on resistance and gate charge; a good selection should minimize the ratio CRSS / CGS where Equation 44 CGS = CISS − CRSS 44/53 PM6670 Application information Tested low-side MOSFETs are listed in Table 16. Table 17. Evaluated low-side MOSFETs Manufacturer Type RDSon (mΩ) CGD \ CGS Rated reverse voltage (V) ST STS12NH3LL 13.5 0.069 30 ST STS25NH3LL 40 0.011 30 IR IRF7811 24 0.054 30 Dual N-MOS can be used in applications with lower output current. Table 18 shows some suitable dual MOSFETs for applications requiring about 3A. Table 18. Suitable dual MOSFETs 8.1.5 Manufacturer Type RDSon (mΩ) Gate Charge (nC) Rated reverse voltage (V) ST STS8DNH3LL 25 10 30 IR IRF7313 46 33 30 Diode selection A rectifier across the synchronous switch is recommended. The rectifier works as a voltage clamp across the synchronous rectifier and reduces the negative inductor swing during the dead time between turning the high-side MOSFET off and the synchronous rectifier on. Moreover it increases the efficiency of the system. Choose a schottky diode as long as its forward voltage drop is very little (0.3V). The reverse voltage should be greater than the maximum input voltage VINmax and a minimum recovery reverse charge is preferable. Table 19 shows some evaluated diodes. Table 19. Evaluated recirculation rectifiers Manufacturer Type Forward voltage (V) Rated reverse voltage (V) Reverse current (µA) ST STPS1L30M 0.34 30 0.00039 ST STPS1L30A 0.34 30 0.00039 45/53 Application information 8.1.6 PM6670 VDDQ current limit setting The valley current limit is set by RCSNS and must be chosen to support the maximum load current. The valley of the inductor current ILvalley is: Equation 45 ILvalley = ILOAD (max) − ∆IL 2 The output current limit depends on the current ripple as shown I Figure 41: Figure 41. Valley current limit waveforms Inductor current Current Inductor current MAX LOAD 2 MAX LOAD 1 Valley current limit Time As the valley threshold is fixed, the greater the current ripple, the greater the DC output current will be. If an output current limit greater than ILOAD(max) over all the input voltage range is required, the minimum current ripple must be considered in the previous formula. Then the resistor RCSNS is: Equation 46 RCSNS = RDSon ⋅ ILvalley 100uA where RDSon is the drain-source on-resistance of the low-side switch. Consider the temperature effect and the worst case value in RDSon calculation (typically +0.4%/°C). The accuracy of the valley current also depends on the offset of the internal comparator (±5mV). The negative valley-current limit (if the device works in forced-PWM mode) is given by: Equation 47 INEG = 46/53 120mV RDSon PM6670 8.1.7 Application information All ceramic capacitors application Design of external feedback network depends on the output voltage ripple across the output capacitors' ESR. If the ripple is great enough (at least 20mV), the compensation network simply consists of a CINT capacitor. Figure 42. Integrative compensation Ton One-shot generator VSNS VDDQ + PWM Comparator - VREF + COMP gm Integrator CFILT RINT - Vr=0.9 CINT The stability of the system depends firstly on the output capacitor zero frequency. It must be verified that: Equation 48 fSW > k ⋅ fZout = k 2π ⋅ R out C out where k is a free design parameter greater than unity (k > 3) . It determines the minimum integrator capacitor value CINT: Equation 49 CINT > gm Vref ⎛f ⎞ Vo 2π ⋅ ⎜ SW − fZout ⎟ k ⎝ ⎠ ⋅ 47/53 Application information PM6670 If the ripple on pin COMP is greater than the integrator output dynamic (150mV), an additional capacitor Cfilt could be added in order to reduce its amplitude. If q is the desired attenuation factor of the output ripple, select: Equation 50 C filt = CINT ⋅ (1 − q) q In order to reduce noise on pin COMP, it's possible to introduce a resistor RINT that, together with CINT and Cfilt, becomes a low psas filter. The cutoff frequency fCUT must be much greater (10 or more times) than the switching frequency of the section: Equation 51 RINT = 2π ⋅ fCUT 1 CINT ⋅ CFILT CINT + CFILT For most of applications both RINT and Cfilt are unnecessary. If the ripple is very small (e.g. such as with ceramic capacitors), an additional compensation network, called "Virtual ESR" network, is needed. This additional part generates a triangular ripple that substitutes the ESR output voltage ripple. The complete compensation scheme is represented in Figure 43. Figure 43. Virtual ESR network L R R1 CINT VDDQ C RINT PWM Comparator Ton Generation Block 48/53 + gm + - VREF CFILT Integrator 0.9V PM6670 Application information Select C as shown: Equation 52 C > 5 ⋅ CINT Then calculate R in order to have enough ripple voltage on the integrator input: Equation 53 R= L R VESR ⋅ C Where RVESR is the new virtual output capacitor ESR. A good trade-off is to consider an equivalent ESR of 30-50mΩ , even though the choice depends on inductor current ripple. Then choose R1 as follows: Equation 54 ⎛ 1 ⎞ ⎟ R ⋅ ⎜⎜ CπfZ ⎟⎠ ⎝ R1 = 1 R− CπfZ 49/53 Package mechanical data 9 PM6670 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Table 20. VFQFPN-24 4mm x 4mm mechanical data mm. Dim. Typ A Min. Max. 0.80 1.00 A1 0.00 0.05 A2 0.65 0.80 D 4.00 D1 3.75 E 4.00 E1 3.75 θ 12° P 0.42 e 0.50 N 24.00 Nd 6.00 Ne 6.00 L 0.40 b 50/53 0.24 0.60 0.30 0.50 0.18 0.30 D2 2.10 1.95 2.25 E2 2.10 1.95 2.25 PM6670 Package mechanical data Figure 44. Package dimensions 51/53 Revision history 10 PM6670 Revision history Table 21. Revision history 52/53 Date Revision 1-Mar-2007 1 Changes Initial release PM6670 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 53/53