Revised June 2000 FSTD16211 24-Bit Bus Switch with Level Shifting General Description Features The Fairchild Switch FSTD16211 provides 24-bits of highspeed CMOS TTL-compatible bus switching. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. A diode to VCC has been integrated into the circuit to allow for level shifting between 5V inputs and 3.3V outputs. ■ 4Ω switch connection between two ports. ■ Minimal propagation delay through the switch. ■ Low lCC. ■ Zero bounce in flow-through mode. ■ Control inputs compatible with TTL level. The device is organized as a 12-bit or 24-bit bus switch. When OE1 is LOW, the switch is ON and Port 1A is connected to Port 1B. When OE2 is LOW, Port 2A is connected to Port 2B. When OE1/2 is HIGH, a high impedance state exists between the A and B Ports. Ordering Code: Order Number Package Number Package Description FSTD16211MTD MTD56 56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Logic Diagram Connection Diagram Truth Table Inputs Inputs/Outputs OE1 OE2 1A, 1B 2A, 2B L L 1A = 1B 2A = 2B L H 1A = 1B Z H L Z 2A = 2B H H Z Z © 2000 Fairchild Semiconductor Corporation DS500313 Pin Descriptions Pin Name Description OE1, OE2 Bus Switch Enables 1A, 2A Bus A 1B, 2B Bus B www.fairchildsemi.com FSTD16211 24-Bit Bus Switch with Level Shifting June 2000 FSTD16211 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions (Note 4) Supply Voltage (VCC) −0.5V to +7.0V DC Switch Voltage (VS) (Note 2) −0.5V to +7.0V Power Supply Operating (VCC) DC Input Control Pin Voltage (VIN)(Note 3) −0.5V to +7.0V Input Voltage (VIN) 0V to 5.5V 0V to 5.5V DC Input Diode Current (lIK) VIN < 0V −50mA Output Voltage (VOUT) DC Output (IOUT) 128mA Input Rise and Fall Time (tr, tf) +/− 100mA DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG) 4.5V to 5.5V Switch Control Input −65°C to +150 °C 0nS/V to 5nS/V Switch I/O 0nS/V to DC -40 °C to +85 °C Free Air Operating Temperature (TA) Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: VS is the voltage observed/applied at either A or B Ports across the switch. Note 3: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 4: Unused control inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics VCC Symbol Parameter (V) VIK Clamp Diode Voltage VIH HIGH Level Input Voltage 4.5–5.5 VIL LOW Level Input Voltage 4.5–5.5 VOH HIGH Level 4.5–5.5 II Input Leakage Current TA = −40 °C to +85 °C Min Typ (Note 5) Max −1.2 4.5 2.0 Units V Conditions IIN = −18mA V 0.8 See Figure 3 V V 5.5 ±1.0 µA 0≤ VIN ≤5.5V 0 10 µA VIN = 5.5V ±1.0 µA 0 ≤A, B ≤VCC IOZ OFF-STATE Leakage Current 5.5 RON Switch On Resistance 4.5 4 7 Ω VIN = 0V, IIN = 64mA (Note 6) 4.5 4 7 Ω VIN = 0V, IIN = 30mA 4.5 35 50 Ω VIN = 2.4V, IIN = 15mA 1.5 mA ICC Quiescent Supply Current 5.5 OE1 = OE2 = GND VIN = VCC or GND, IOUT = 0 10 µA OE1 = OE2 = V CC VIN = VCC or GND, IOUT = 0 ∆ ICC Increase in ICC per Input 5.5 2.5 mA One input at 3.4V Other inputs at VCC or GND Note 5: Typical values are at VCC = 5.0V and T A= +25°C Note 6: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins. www.fairchildsemi.com 2 TA = −40 °C to +85 °C, Symbol Parameter CL = 50pF, RU = RD = 500Ω Min tPHL,tPLH Prop Delay Bus to Bus (Note 7) tPZH, tPZL Output Enable Time Units VCC = 4.5 – 5.5V Figure Conditions Number Max 0.25 ns 5.5 ns 1.5 VI = OPEN Figures 1, 2 VI = 7V for tPZL Figures 1, 2 VI = OPEN for tPZH tPHZ, tPLZ Output Disable Time 1.5 6.5 ns VI = 7V for tPLZ Figures 1, 2 VI = OPEN for tPHZ Note 7: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical ON resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance). Capacitance Symbol (Note 8) Parameter Typ Max Units Conditions CIN Control Pin Input Capacitance 3.5 pF VCC = 5.0V CI/O Input/Output Capacitance 5.5 pF VCC, OE = 5.0V Note 8: TA = +25°C, f = 1 MHz, Capacitance is characterized but not tested. AC Loading and Waveforms Note: Input driven by 50Ω source terminated in 50Ω Note: CL includes load and stray capacitance Note: Input PRR = 1.0 MHz, tW = 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms 3 www.fairchildsemi.com FSTD16211 AC Electrical Characteristics FSTD16211 Output Voltage HIGH vs. Supply Voltage FIGURE 3. www.fairchildsemi.com 4 FSTD16211 24-Bit Bus Switch with Level Shifting Physical Dimensions inches (millimeters) unless otherwise noted 56-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD56 Technology Description The Fairchild Switch family derives from and embodies Fairchild’s proven switch technology used for several years in its 74LVX3L384 (FST3384) bus switch product. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 5 www.fairchildsemi.com