Revised May 2003 NC7SV125 TinyLogic ULP-A Buffer with 3-STATE Output General Description Features The NC7SV125 is a single buffer with 3-STATE output from Fairchild’s Ultra Low Power-A (ULP-A) Series of TinyLogic. ULP-A is ideal for applications that require extreme high speed, high drive and low power. This product is designed for wide low voltage operating range (0.9V to 3.6V VCC) and applications that require more drive and speed than the TinyLogic ULP series, but still offer best in class low power operation. The NC7SV125 is uniquely designed for optimized power and speed, and is fabricated with an advanced CMOS technology to achieve high-speed operation while maintaining low CMOS power dissipation. ■ 0.9V to 3.6V VCC supply operation ■ 3.6V overvoltage tolerant I/O’s at VCC from 0.9V to 3.6V ■ Extremely High Speed tPD 1.0 ns typ for 2.7V to 3.6V VCC 2.0 ns typ for 2.3V to 2.7V VCC 3.0 ns typ for 1.65V to 1.95V VCC 3.5 ns typ for 1.4V to 1.6V VCC 6.0 ns typ for 1.1V to 1.3V VCC 13 ns typ for 0.9V VCC ■ Power-Off high impedance inputs and outputs ■ High Static Drive (IOH/IOL) ±24 mA @ 3.00V VCC ±18 mA @ 2.30V VCC ±6 mA @ 1.65V VCC ±4 mA @ 1.4V VCC ±2 mA @ 1.1V VCC ±0.1 mA @ 0.9V VCC ■ Uses patented Quiet Series noise/EMI reduction circuitry ■ Ultra small MicroPak leadfree package ■ Ultra low dynamic power Ordering Code: Package Product Code Number Top Mark NC7SV125P5X MAA05A V25 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3k Units on Tape and Reel NC7SV125L6X MAC06A H6 6-Lead MicroPak, 1.0mm Wide 5k Units on Tape and Reel Order Number Package Description Supplied As Battery Life vs. VCC Supply Voltage TinyLogic ULP and ULP-A with up to 50% less power consumption can extend your battery life significantly. Battery Life = (Vbattery *Ibattery*.9)/(Pdevice)/24hrs/day Where, Pdevice = (ICC * VCC) + (CPD + C L) * VCC2 * f Assumes ideal 3.6V Lithium Ion battery with current rating of 900mAH and derated 90% and device frequency at 10MHz, with CL = 15 pF load TinyLogic is a registered trademark of Fairchild Semiconductor Corporation. MicroPak, and Quiet Series are trademarks of Fairchild Semiconductor Corporation. © 2003 Fairchild Semiconductor Corporation DS500616 www.fairchildsemi.com NC7SV125 TinyLogic ULP-A Buffer with 3-STATE Output October 2001 NC7SV125 Logic Symbol Connection Diagrams IEEE/IEC Pin Assignments for SC70 Pin Descriptions (Top View) Pin Names Description A, OE Input Y Output NC No Connect Pad Assignments for MicroPak Function Table Input Output OE In A L L L L H H H X Z Out Y (Top Thru View) H = HIGH Logic Level L = LOW Logic Level X = HIGH or LOW Logic Level Z = HIGH Impedance State www.fairchildsemi.com 2 Supply Voltage (VCC) −0.5V to +4.6V DC Input Voltage (VIN) −0.5V to +4.6V Recommended Operating Conditions (Note 3) Supply Voltage DC Output Voltage (VOUT) 0.9V to 3.6V Input Voltage (VIN) −0.5V to VCC +0.5V HIGH or LOW State (Note 2) VCC = 0V −0.5V to +4.6V DC Input Diode Current (IIK) VIN < 0V 0V to 3.6V Output Voltage (VOUT) ±50 mA DC Output Diode Current (IOK) VCC = 0.0V 0V to 3.6V HIGH or LOW State 0V to VCC Output Current in IOH/IOL VOUT < 0V −50 mA VCC = 3.0V to 3.6V ±24 mA VOUT > VCC +50 mA VCC = 2.3V to 2.7V ±18 mA ± 50 mA VCC = 1.65V to 1.95V ±6 mA VCC = 1.4V to 1.6V ±4 mA DC Output Source/Sink Current (IOH/IOL) DC VCC or Ground Current per ± 50 mA Supply Pin (ICC or Ground) Storage Temperature Range (TSTG) VCC = 1.1V to 1.3V −65°C to +150 °C ±2 mA VCC = 0.9V ±0.1 mA −40°C to +85°C Free Air Operating Temperature (TA) Minimum Input Edge Rate (∆t/∆V) VIN = 0.8V to 2.0V, VCC = 3.0V 10 ns/V Note 1: Absolute Maximum Ratings: are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: IO Absolute Maximum Rating must be observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol VIH Parameter HIGH Level Input Voltage VIL LOW Level Input Voltage VCC TA = +25°C (V) Min 0.90 Max HIGH Level Output Voltage Min 0.65 x VCC 0.65 x VCC 1.10 ≤ VCC ≤ 1.30 0.65 x VCC 0.65 x VCC 1.40 ≤ VCC ≤ 1.60 0.65 x VCC 0.65 x VCC 1.65 ≤ VCC ≤ 1.95 0.65 x VCC 0.65 x VCC 2.30 ≤ VCC < 2.70 1.6 2.70 ≤ VCC ≤ 3.60 2.0 Units Conditions Max V 1.6 2.0 0.90 0.35 x VCC 0.35 x VCC 1.10 ≤ VCC ≤ 1.30 0.35 x VCC 0.35 x VCC 1.40 ≤ VCC ≤ 1.60 0.35 x VCC 0.35 x VCC 1.65 ≤ VCC ≤ 1.95 0.35 x VCC 0.35 x VCC 2.30 ≤ VCC < 2.70 0.7 0.7 2.70 ≤ VCC ≤ 3.60 VOH TA = −40°C to +85°C 0.8 0.8 0.90 VCC − 0.1 VCC − 0.1 1.10 ≤ VCC ≤ 1.30 VCC − 0.1 VCC − 0.1 1.40 ≤ VCC ≤ 1.60 VCC − 0.2 VCC − 0.2 1.65 ≤ VCC ≤ 1.95 VCC − 0.2 VCC − 0.2 2.30 ≤ VCC < 2.70 VCC − 0.2 VCC − 0.2 2.70 ≤ VCC ≤ 3.60 VCC − 0.2 VCC − 0.2 1.10 ≤ VCC ≤ 1.30 0.75 x VCC 0.75 x VCC 1.40 ≤ VCC ≤ 1.60 0.75 x VCC 0.75 x VCC 1.65 ≤ VCC ≤ 1.95 1.25 1.25 2.30 ≤ VCC < 2.70 2.0 2.0 2.30 ≤ VCC < 2.70 1.8 1.8 2.70 ≤ VCC ≤ 3.60 2.2 2.2 2.30 ≤ VCC < 2.70 1.7 1.7 2.70 ≤ VCC ≤ 3.60 2.4 2.4 2.70 ≤ VCC ≤ 3.60 2.2 2.2 3 V IOH = −100 µA IOH = −2 mA V IOH = −4 mA IOH = −6 mA IOH = −12 mA IOH = −18 mA IOH = −24 mA www.fairchildsemi.com NC7SV125 Absolute Maximum Ratings(Note 1) NC7SV125 DC Electrical Characteristics Symbol (Continued) TA = +25°C VCC Parameter (V) VOL LOW Level Output Voltage Min TA = −40°C to +85°C Max Min Units Conditions Max 0.90 0.1 0.1 1.10 ≤ VCC ≤ 1.30 0.1 0.1 1.40 ≤ VCC ≤ 1.60 0.2 0.2 1.65 ≤ VCC ≤ 1.95 0.2 0.2 2.30 ≤ VCC < 2.70 0.2 0.2 IOL = 100 µA 2.70 ≤ VCC ≤ 3.60 0.2 0.2 1.10 ≤ VCC ≤ 1.30 0.25 x VCC 0.25 x VCC 1.40 ≤ VCC ≤ 1.60 0.25 x VCC 0.25 x VCC 1.65 ≤ VCC ≤ 1.95 0.3 0.3 2.30 ≤ VCC < 2.70 0.4 0.4 2.70 ≤ VCC ≤ 3.60 0.4 0.4 2.30 ≤ VCC < 2.70 0.6 0.6 2.70 ≤ VCC ≤ 3.60 0.4 0.4 V IOL = 2 mA IOL = 4 mA IOL = 6 mA IOL = 12 mA IOL = 18 mA 2.70 ≤ VCC ≤ 3.60 0.55 0.55 IIN Input Leakage Current 0.90 to 3.60 ±0.1 ±0.9 µA IOL = 24 mA IOZ 3-STATE Output Leakage 0.90 to 3.60 ±1.0 ±5.0 µA 0 ≤ VI ≤ 3.6V VI = VIH or VIL 0 ≤ VO ≤ 3.6V IOFF Power Off Leakage Current ICC Quiescent Supply Current 0 1 5 0.90 to 3.60 0.9 5 ±5 0.90 to 3.60 µA µA 0 ≤ (VI, VO) ≤ 3.6V VI = VCC or GND VCC ≤ VI ≤ 3.6V AC Electrical Characteristics Symbol tPHL Parameter Propagation Delay tPLH tPZH Output tPZL Enable Time tPHZ Output tPLZ Disable Time TA = +25°C VCC (V) Min Typ 1.10 ≤ VCC ≤ 1.30 3.0 1.40 ≤ VCC ≤ 1.60 1.65 ≤ VCC ≤ 1.95 TA = −40°C to +85°C Units Min Max 6.0 9.8 1.9 14.9 1.0 3.5 5.3 0.8 5.7 0.9 3.0 4.3 0.8 4.6 2.30 ≤ VCC < 2.70 0.8 2.0 2.8 0.7 3.0 2.70 ≤ VCC ≤ 3.60 0.5 1.0 2.6 0.5 2.8 1.10 ≤ VCC ≤ 1.30 3.0 6.0 9.7 2.0 16.4 1.40 ≤ VCC ≤ 1.60 1.2 4.0 6.0 1.0 7.5 1.65 ≤ VCC ≤ 1.95 1.0 3.0 4.5 0.9 5.0 2.30 ≤ VCC < 2.70 0.8 2.0 3.0 0.7 3.4 S1 = VI for tPZL 2.70 ≤ VCC ≤ 3.60 0.5 1.2 2.6 0.4 2.9 VI = 2 x VCC RU = 1kΩ 0.90 0.90 CL = 15 pF, RL = 2 kΩ ns Figures 1, 2 CL = 30 pF RU = 1kΩ ns RD = 1kΩ S1 = GND for tPZH Figures 1, 2 CL = 30 pF 14 1.10 ≤ VCC ≤ 1.30 2.0 5.0 9.5 2.0 14.0 1.40 ≤ VCC ≤ 1.60 1.2 3.0 5.5 1.1 7.0 1.65 ≤ VCC ≤ 1.95 1.0 2.0 5.6 0.8 5.8 2.30 ≤ VCC < 2.70 0.8 1.5 4.2 0.5 5.0 2.70 ≤ VCC ≤ 3.60 0.5 1.0 3.9 0.4 4.2 ns S1 = GND for tPHZ VI = 2 x VCC 0 2.0 pF COUT Output Capacitance 0 4.5 pF CPD Power Dissipation 0.90 to 3.60 10 pF 4 RD = 1kΩ S1 = VI for tPLZ Input Capacitance www.fairchildsemi.com CL = 30 pF RL = 500Ω 14 0.90 Figure Number CL = 15 pF, RL = 1 MΩ 13 CIN Capacitance Conditions Max VI = 0V or VCC f = 10 MHz Figures 1, 2 NC7SV125 AC Loading and Waveforms FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms Symbol VCC 3.3V ± 0.3V 2.5V ± 0.2V 1.8V ± 0.15V 1.5V ± 0.10V 1.2V ± 0.10V 0.9V Vmi 1.5V VCC/2 VCC/2 VCC/2 VCC/2 VCC/2 Vmo 1.5V VCC/2 VCC/2 VCC/2 VCC/2 VCC/2 5 www.fairchildsemi.com NC7SV125 Tape and Reel Specification TAPE FORMAT for SC70 Package Designator P5X Tape Number Cavity Section Cavities Status Status Leader (Start End) 125 (typ) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) www.fairchildsemi.com Cover Tape 6 TAPE FORMAT for MicroPak Package Designator (Continued) Tape Number Cavity Section Cavities Status Status Leader (Start End) 125 (typ) Empty Sealed L6X Cover Tape Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed N W1 W2 W3 TAPE DIMENSIONS inches (millimeters) REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A B C D 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/−0.000 0.567 W1 + 0.078/−0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/−0.00) (14.40) (W1 + 2.00/−1.00) 7 www.fairchildsemi.com NC7SV125 Tape and Reel Specification NC7SV125 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide Package Number MAA05A www.fairchildsemi.com 8 NC7SV125 TinyLogic ULP-A Buffer with 3-STATE Output Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com