IRF IRSM836

IRSM836-035MB
3A, 500V
Integrated Power Module for
Small Appliance Motor Drive Applications
Description
IRSM836-035MB is a 3A, 500V Integrated Power Module (IPM) designed for advanced appliance motor drive
applications such as energy efficient fans and pumps. IR's technology offers an extremely compact, high
performance AC motor-driver in an isolated package. This advanced IPM offers a combination of IR's low RDS(on)
Trench MOSFET technology and the industry benchmark 3-phase high voltage, rugged driver in a small PQFN
package. At only 12x12mm and featuring integrated bootstrap functionality, the compact footprint of this surfacemount package makes it suitable for applications that are space-constrained. Integrated over-current protection,
fault reporting and under-voltage lockout functions deliver a high level of protection and fail-safe operation.
IRSM836-035MB functions without a heat sink.
Features
•
•
•
•
•
•
•
•
•
•
•
Integrated gate drivers and bootstrap functionality
Suitable for single shunt sensing
Protection shutdown pin
Low RDS(on) Trench FREDFET
Under-voltage lockout for all channels
Matched propagation delay for all channels
Optimized dV/dt for loss and EMI trade offs
3.3V Schmitt-triggered active high input logic
Cross-conduction prevention logic
Motor power range up to ~110W, without heat sink
Isolation 1500VRMS min
Base Part Number
Package Type
IRSM836-035MB
27L
PQFN 12 x 12 mm
IRSM836-035MB
Standard Pack
Orderable Part Number
Form
Quantity
Tape and Reel
2000
IRSM836-035MBTR
Tray
800
IRSM836-035MB
All part numbers are PbF
1
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Internal Electrical Schematic
VB1 VB2 VB3
IRSM836-035MB
V+
VCC
HIN1
HIN2
HIN3
LIN1
LIN2
LIN3
FAULT
ITRIP
EN
RCIN
U, VS1
V, VS2
W, VS3
600V
3-Phase
Driver
HVIC
COM
V-
VSS
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the module may occur. These are not tested at
manufacturing. All voltage parameters are absolute voltages referenced to VSS unless otherwise stated in the table.
Symbol
Description
Min
Max
Unit
V
BVDSS
MOSFET Blocking Voltage
---
500
IO @ T=25°C
DC Output Current per MOSFET
---
3
IOP
Pulsed Output Current (Note 1)
---
20
Pd @ TC=25°C
Maximum Power Dissipation per MOSFET
---
36
W
VISO
Isolation Voltage (1min) (Note 2)
---
1500
VRMS
TJ
Operating Junction Temperature
-40
150
°C
TL
Lead Temperature (Soldering, 30 seconds)
---
260
°C
TS
Storage Temperature
-40
150
°C
VS1,2,3
High Side Floating Supply Offset Voltage
VB1,2,3 - 20
VB1,2,3 +0.3
V
VB1,2,3
High Side Floating Supply Voltage
-0.3
500
V
VCC
Low Side and Logic Supply voltage
-0.3
20
V
VSS -0.3
VCC+0.3
V
VIN
Input Voltage of LIN, HIN, ITRIP, EN, RCIN, FLT
Note 1: Pulse Width = 100µs, TC =25°C, Duty=1%.
Note 2: Characterized, not tested at manufacturing
2
www.irf.com
© 2013 International Rectifier
A
February 3, 2013
IRSM836-035MB
Recommended Operating Conditions
Symbol
Description
V+
Positive DC Bus Input Voltage
Min
Max
Unit
---
400
V
VS1,2,3
High Side Floating Supply Offset Voltage
(Note 3)
400
V
VB1,2,3
High Side Floating Supply Voltage
VS+12
VS+20
V
VCC
Low Side and Logic Supply Voltage
13.5
16.5
V
VIN
Input Voltage of LIN, HIN, ITRIP, EN, FLT
0
5
V
Fp
PWM Carrier Frequency
---
20
kHz
The Input/Output logic diagram is shown in Figure 1. For proper operation the module should be used within the
recommended conditions. All voltages are absolute referenced to COM. The VS offset is tested with all supplies biased at 15V
differential.
Note 3: Logic operational for Vs from COM-5V to COM+250V. Logic state held for Vs from COM-5V to COM-VBS.
Static Electrical Characteristics
o
(VCC-COM) = (VB-VS) = 15 V. TA = 25 C unless otherwise specified. The VIN and IIN parameters are referenced to VSS and are
applicable to all six channels. The VCCUV parameters are referenced to VSS. The VBSUV parameters are referenced to VS.
Symbol
Description
Min
Typ
Max
Units
BVDSS
Drain-to-Source Breakdown Voltage
500
---
---
V
TJ=25°C, ILK=250µA
ILKH
Leakage Current of High Side FET’s in
Parallel
10
µA
TJ=25°C, VDS=500V
ILKL
Leakage Current of Low Side FET’s in
Parallel Plus Gate Drive IC
15
µA
TJ=25°C, VDS=500V
RDS(ON)
Drain to Source ON Resistance
---
1.85
2.2
Ω
TJ=25°C, VCC=15V, Id = 1A
VIN,th+
Positive Going Input Threshold
2.5
---
---
V
VIN,th-
Negative Going Input Threshold
---
---
0.8
V
VCCUV+,
VBSUV+
VCC and VBS Supply Under-Voltage,
Positive Going Threshold
8
8.9
9.8
V
VCCUV-,
VBSUV-
VCC and VBS supply Under-Voltage,
Negative Going Threshold
7.4
8.2
9
V
VCCUVH,
VBSUVH
VCC and VBS Supply Under-Voltage
Lock-Out Hysteresis
---
0.7
---
V
IQBS
Quiescent VBS Supply Current VIN=0V
---
---
125
µA
IQCC
Quiescent VCC Supply Current VIN=0V
---
---
3.35
mA
IQCC, ON
Quiescent VCC Supply Current VIN=4V
---
---
10
mA
IIN+
Input Bias Current VIN=4V
---
100
160
µA
IIN-
Input Bias Current VIN=0V
---
--
1
µA
ITRIP+
ITRIP Bias Current VITRIP=4V
---
5
40
µA
ITRIP-
ITRIP Bias Current VITRIP=0V
---
--
1
µA
VIT, TH+
ITRIP Threshold Voltage
0.37
0.46
0.55
V
VIT, TH-
ITRIP Threshold Voltage
---
0.4
---
V
3
www.irf.com
Conditions
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
VIT, HYS
ITRIP Input Hysteresis
---
0.06
---
V
RBR
Internal Bootstrap Equivalent Resistor
Value
---
200
---
Ω
VRCIN,TH
RCIN Positive Going Threshold
---
8
---
V
RON,FAULT
FAULT Open-Drain Resistance
---
50
100
Ω
Min
Typ
Max
Units
0.7
1.5
µs
TJ=25°C
Note 4: Characterized, not tested at manufacturing
Dynamic Electrical Characteristics
o
(VCC-COM) = (VB-VS) = 15 V. TA = 25 C unless otherwise specified.
Symbol
Description
Conditions
TON
Input to Output Propagation Turn-On
Delay Time
---
TOFF
Input to Output Propagation Turn-Off
Delay Time
---
0.7
1.5
µs
TFIL,IN
Input Filter Time (HIN, LIN)
200
330
---
ns
VIN=0 & VIN=4V
TFIL,EN
Input Filter Time (EN)
100
200
---
ns
VIN=0 & VIN=4V
TBLT-ITRIP
ITRIP Blanking Time
100
330
ns
VIN=0 & VIN=4V, VI/Trip=5V
TFAULT
Itrip to Fault
---
600
1000
ns
VIN=0 & VIN=4V
TEN
EN Falling to Switch Turn-Off
700
1000
ns
VIN=0 & VIN=4V
TITRIP
ITRIP to Switch Turn-Off Propagation Delay
950
1300
ns
ID=1A, V =50V, See Figure 3
+
ID=1mA, V =50V
See Fig.2
---
+
MOSFET Avalanche Characteristics
Symbol
Description
EAS
Single Pulse Avalanche Energy
Min
Typ
Max
Units
Conditions
TJ=25°C, L=93mH, VDD=150V,
ITEST=1.8A, TO-220 package
---
150
---
mJ
Min
Typ
Max
Units
Conditions
Thermal and Mechanical Characteristics
Symbol
Description
Rth(J-CT)
Total Thermal Resistance Junction to
Case Top
---
27.4
---
°C/W
One device
Rth(J-CB)
Total Thermal Resistance Junction to
Case Bottom
---
2.2
---
°C/W
One device
4
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Qualification Information†
††
Qualification Level
Industrial
(per JEDEC JESD 47E)
Moisture Sensitivity Level
MSL3
(per IPC/JEDEC J-STD-020C)
†††
Machine Model
Class B
(per JEDEC standard JESD22-A115)
Human Body Model
Class 2
(per standard ESDA/JEDEC JS-001-2012)
ESD
RoHS Compliant
Yes
†
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
††
Higher qualification ratings may be available should the user have such requirements. Please contact
your International Rectifier sales representative for further information.
†††
Higher MSL ratings may be available for the specific package types listed here. Please contact your
International Rectifier sales representative for further information.
5
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Input/ Output Pin Equivalent Circuit Diagrams
VB
ESD
Diode
20 V
Clamp
HO
ESD
Diode
V CC
HIN,
LIN,
or EN
VS
ESD
Diode
600 V
VCC
20 V
Clamp
ESD
Diode
33k
ESD
Diode
25 V
Clamp
VSS
LO
ESD
Diode
COM
VCC
VCC
ESD
Diode
ESD
Diode
RCIN or
FAULT
ITRIP
ESD
Diode
VSS
6
www.irf.com
ESD
Diode
1M
VSS
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Input-Output Logic Level Table
V+
Ho
Hin1,2,3
Gate
Driver
IC
U, V, W
Lo
Lin1,2,3
EN
Itrip
Hin1,2,3
Lin1,2,3
U,V,W
1
0
1
0
V+
1
0
0
1
0
1
0
0
0
off
1
1
X
X
off
0
X
X
X
off
HIN1,2,3
LIN1,2,3
ITRIP
U,V,W
Figure 1: Input/Output Logic Diagram
7
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
ID
VDS
ID
VDS
90% ID
50%
HIN /LIN
90% ID
50%
VDS
HIN /LIN
50%
HIN /LIN
HIN /LIN
50%
VCE
10% ID
10% ID
tf
tr
TON
TOFF
Figure 2a: Input to Output propagation turn-on
delay time.
Figure 2b: Input to Output propagation turn-off
delay time.
IF
VDS
HIN /LIN
Irr
trr
Figure 2c: Diode Reverse Recovery.
Figure 2: Switching Parameter Definitions
8
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
HIN1,2,3
LIN1,2,3
50%
50%
ITRIP
U,V,W
50%
50%
TITRIP
TFLT-CLR
Figure 3: ITRIP Timing Waveform
9
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Module Pin-Out Description
Pin
Name
Description
1
HIN3
Logic Input High Side Gate Driver - Phase 3
2
LIN1
Logic Input Low Side Gate Driver - Phase 1
3
LIN2
Logic Input Low Side Gate Driver - Phase 2
4
LIN3
Logic Input Low Side Gate Driver - Phase 3
5
/FLT
Fault Output
6
ITRIP
Current Protection Pin
7
EN
Enable Pin
8
RCIN
RCIN Reset Programming Pin
9
10, 11, 21,
28
12, 13, 29
VSS
Negative Main Supply
U,VS1
Output 1 - High Side Floating Supply Offset Voltage
V,VS2
Output 2 - High Side Floating Supply Offset Voltage
14, 15
16, 17, 30,
31
18, 19, 20
W,VS3
Output 3 - High Side Floating Supply Offset Voltage
V-
Negative Bus Input Voltage, COM
V
Positive Bus Input Voltage
22
VB1
High Side Floating Supply voltage 1
23
VB2
High Side Floating Supply voltage 2
24
VB3
High Side Floating Supply Voltage 3
25
VCC
+15V Main Supply
26
HIN1
Logic Input High Side Gate Driver - Phase 1
27
HIN2
Logic Input High Side Gate Driver - Phase 2
+
17
16
18
19
Top View
20
15
14
29
21
28
22
13
12
23
24
30
31
25
26
27
1
10
www.irf.com
2 3 4 5 6 7 8 9
Notes
Pin 28,29, 31 are not required to
be connected electrically on the
PCB
All pins with the same name are
internally connected. For
example, pins 10, 11, 21 and 28
are internally connected.
10 11
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Fault Reporting and Programmable Fault Clear Timer
The IRSM836-035MB provides an integrated fault reporting output and an adjustable fault clear timer.
There are two situations that would cause the IRSM836-035MB to report a fault via the FAULT pin. The first is an
under-voltage condition of VCC and the second is when the ITRIP pin recognizes a fault. Once the fault condition
occurs, the FAULT pin is internally pulled to VSS and the fault clear timer is activated. The fault output stays in the
low state until the fault condition has been removed and the fault clear timer expires; once the fault clear timer
expires, the voltage on the FAULT pin will return to VCC.
The length of the fault clear time period (tFLTCLR) is determined by exponential charging characteristics of
the capacitor where the time constant is set by RRCIN and CRCIN. In Figure 4 where we see that a fault condition
has occurred (UVLO or ITRIP), RCIN and FAULT are pulled to VSS, and once the fault has been removed, the
fault clear timer begins. Figure 5 shows that RRCIN is connected between the VCC and the RCIN pin, while CRCIN is
placed between the RCIN and VSS pins.
V cc
HIN (x 3)
ITRIP
VB ( x3 )
LIN (x 3)
EN
VRCIN
tFLTCLR
IRSM836-035MB
VS (x 3 )
FAULT
VCC
R RCIN
VRCIN,TH
RCIN
Time
VSS
ITRIP
CRCIN
VRx
VSS
VFAULT
High
Impedance State
VSS
Time
I
Figure 4: RCIN and FAULT pin waveforms
-
Figure 5: Programming the fault clear timer
The design guidelines for this network are shown in Table 1.
≤1 nF
CRCIN
Ceramic
0.5 MΩ to 2 MΩ
RRCIN
>> RON,RCIN
Table 1: Design guidelines
The length of the fault clear time period can be determined by using the formula below.
 V
t FLTCLR = −(RRCIN CRCIN )ln1 − RCIN ,TH
VCC

11
www.irf.com



© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Typical Application Connection IRSM836-035MB
VB2
VB1
VB3
IRSM836-035MB
VBUS
2M
VCC
XTAL0
XTAL1
SPD-REF
AIN2
HIN1
PWMVH
HIN2
PWMWH
HIN3
PWMUL
LIN1
PWMVL
LIN2
PWMWL
FAULT
ITRIP
6.04k
AIN1
VDD
EN
IFB+
IFB-
VDDCAP
U, VS1
V, VS2
W, VS3
LIN3
GATEKILL
IRMCK171
Power
Supply
HVIC
PWMUH
2M
6.04k
IFBO
VSS
7.68k
RCIN
VSS
COM
1nF
4.87k
0.5
1. Electrolytic bus capacitors should be mounted as close to the module bus terminals as possible to reduce
ringing and EMI problems. Additional high frequency ceramic capacitor mounted close to the module pins
will further improve performance.
2. In order to provide good decoupling between VCC-VSS and VB1,2,3-VS1,2,3 terminals, the capacitors
shown connected between these terminals should be located very close to the module pins. Additional
high frequency capacitors, typically 0.1µF, are recommended.
3. Value of the boot-strap capacitors depends upon the switching frequency. Their selection should be made
based on application note AN-1044.
4. PWM generator must be disabled within Fault duration to guarantee shutdown of the system. Overcurrent condition must be cleared before resuming operation.
12
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Current Capability in a Typical Application
Figure 6 shows the current capability for this module at specified conditions. The current capability of the
module is affected by application conditions including the PCB layout, ambient temperature, maximum PCB
temperature, modulation scheme, PCB copper thickness and so on. The curves below were obtained from
measurements carried out on the IRMCS1171 reference design board which includes the IRSM836-035MB and
IR’s IRMCK171 digital control IC.
320V, ΔTca = 70 °C
500
450
RMS Current (mA)
400
350
300
250
200
150
1oz, 2ph
1oz, 3ph
2oz, 2ph
2oz, 3ph
100
50
0
5
20
320V, ΔTca = 40 °C
500
450
1oz, 2ph
1oz, 3ph
2oz, 2ph
2oz, 3ph
400
RMS Current (mA)
10
15
Carrier Frequency (kHz)
350
300
250
200
150
100
50
0
5
10
15
Carrier Frequency (kHz)
20
Figure 6: Maximum Sinusoidal Phase Current vs. PWM Switching Frequency
+
Sinusoidal Modulation, V =320V, PF=0.95
13
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
PCB Example
Figure 7 below shows an example layout for the application PCB. The effective area of the V+ top-layer
copper plane is ~3cm² in this example. For an FR4 PCB with 1oz copper, Rth(J-A) is about 40°C/W. A lower Rth(J-A)
can be achieved using thicker copper and/or additional layers.
Module
Figure 7: PCB layout example and corresponding thermal image
At the module’s typical operating conditions, dV/dt of the phase node voltage is influenced by the load
capacitance which includes parasitic capacitance of the PCB, MOSFET output capacitance and motor winding
capacitance. To turn off the MOSFET, the load capacitance needs to be charged by the phase current. For the
IRMCS1171 reference design, turn-off dV/dt ranges from 2 to 5 V/ns depending on the phase current magnitude.
Turn-on dV/dt is influenced by PCB parasitic capacitance and motor winding capacitance and typically ranges
from 4 to 6 V/ns. The MOSFET turn-on loss combined with the complimentary body diode reverse recovery loss
comprises the majority of the total switching losses. Two-phase modulation can be used to reduce switching
losses and run the module at higher phase currents.
14
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
27L Package Outline IRSM836-035MB (Bottom View)
Dimensions in mm
15
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
27L Package Outline IRSM836-035MB (Bottom View)
Dimensions in mm
16
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
27L Package Outline IRSM836-035MB (Top and Side View)
17
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
27L Top Marking
IRSM836-035MB
18
www.irf.com
© 2013 International Rectifier
February 3, 2013
IRSM836-035MB
Revision History
January 30, 2013
Formatting corrections; added notes about what pins are internally connected; updated ordering
table stating all parts are PbF.
Data and Specifications are subject to change without notice
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information
19
www.irf.com
© 2013 International Rectifier
February 3, 2013