ITF FG229

SAW Bandpass Filter FG229
Features
RF bandpass filter
High attenuation
Ceramic Surface Mounted Device (SMD) Package ( 3.0 mm * 3.0 mm )
RoHS Compliant
Package Dimensions
3.00± 0.15
8
I
G229
3
1
6
6
2
5
4
5
1.20
7
3
4
0.75
0.60
2
8
7
1.10± 0.15
3.00± 0.15
1
0.60
Pin Configuration
Dimensions shown are nominal in millimeters
1,2
Input
Body : Al2O3 Ceramic
Lid : Kovar, Ni Plated
Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um
Ni Plating
5,6
Output
3, 4, 7,8
Case ground
Maximum Ratings
Parameter
Unit
Minimum
Typical
Maximum
Operating Temperature Range
℃
-40
25
85
Storage Temperature Range
℃
-40
25
85
Power Handling Capability
dBm
-
-
-
Electrostatics Sensitive Device (ESD)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
1/7
SAW Bandpass Filter FG229
Specifications
Fc = 1220 MHz
Balanced to balanced operation
Terminating source impedance : 200Ω
Terminating load impedance
: 200Ω
Minimum
Typical
Maximum
Unit
Center Frequency ( Fc )
-
1220
-
MHz
Insertion Loss ( 1216 ~ 1224 MHz )
-
3.4
5.3
dB
Amplitude Ripple ( 1216 ~ 1224 MHz )
-
0.6
1.8
dBp-p
0.5 MHz ~ Fc-91 MHz
50
57
-
Fc-91 MHz ~ Fc-85 MHz
50
57
-
Fc-76 MHz ~ Fc-68 MHz
46
57
-
Fc-88 MHz
50
57
-
Fc-72 MHz
48
57
-
Fc-44 MHz
50
56
-
Fc-36 MHz
46
55
-
Fc+70 MHz ~ 2000 MHz
50
55
-
Relative Attenuation
Input/Output Impedance
dB
200
Ohms
Notes :
1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and
full 2 port calibration.
2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing
tolerances
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
2/7
SAW Bandpass Filter FG229
Matching Schematic
( Actual matching values may vary due to PCB layout and parasitics )
Balanced Output
200Ω
Balanced Input
200Ω
Marking Configuration
1)
I2)
G2293)
1) Pad Number 1 Index
2) Manufacturer name
3) Marking Number
* Ink or Laser Marking available
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
3/7
SAW Bandpass Filter FG229
Typical Performance ( at 25℃
℃)
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
4/7
SAW Bandpass Filter FG229
Input / Output VSWR Charts
Input / Output Smith Charts
Packing Specification
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
5/7
SAW Bandpass Filter FG229
1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel )
2. Taping Structure : The tape shall be wound around the reel in the direction shown below.
TOP COVER TAPE
REEL
CARRIER TAPE
Tape Specification
1. Leader part and vacant position specification
Vacant
150mm min.
Component
contained
Vacant
150mm min.
Leader part
250mm min.
END
START
Tape Running Direction
2. Tensile strength of carrier tape
4.4N/mm width
Direction of pull
Top cover tape
3. Top cover tape adhesion
0~ 15 degree
1) pull off angle : 0~15°
2) speed : 300mm/min
3) force : 20~70g
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Carrier tape
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
6/7
SAW Bandpass Filter FG229
Carrier Tape Dimensions [unit : mm]
A
3.40 ± 0.1
B
3.40 ± 0.1
C
7.25 ± 0.1
D
1.70 ± 0.1
E
12.00 ± 0.1
F
8.00 ± 0.1
Part Direction
Tape Running Direction
Reel Dimensions [unit : mm]
I T F Co., Ltd.
102-901, Bucheon Technopark 364,
Samjeong-Dong, Ojeong-Gu, Bucheon-City,
Gyounggi-Do, Korea 421-809
Part No.
FG229
Rev. Date
2011-10-14
Rev.
NCMJ01-AS01
7/7