TI TPS2375DR

data sheet
D−8
TPS2375
TPS2376
TPS2377
PW−8
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
IEEE 802.3af PoE POWERED DEVICE CONTROLLERS
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
Fully Supports IEEE 802.3af Specification
Integrated 0.58-Ω, 100-V, Low-Side Switch
15-kV System Level ESD Capable
Supports Use of Low-Cost Silicon Rectifiers
Programmable Inrush Current Control
Fixed 450-mA Current Limit
Fixed and Adjustable UVLO Options
Open-Drain, Power-Good Reporting
Overtemperature Protection
Industrial Temperature Range: -40°C to 85°C
8-Pin SOIC and TSSOP Packages
VoIP Phones
WLAN Access Points
Security Cameras
Internet Appliances
POS Terminals
TPS2376
(TOP VIEW)
TPS2375/77
(TOP VIEW)
1
2
3
4
ILIM
CLASS
DET
VSS
VDD
N/C
8
1
7
2
6
3
PG
RTN 5
4
ILIM
CLASS
DET
VSS
VDD
UVLO
8
7
6
PG
RTN 5
DESCRIPTION
These easy-to-use 8-pin integrated circuits contain all of the features needed to develop an IEEE 802.3af
compliant powered device (PD). The TPS2375 family is a second generation PDC (PD Controller) featuring
100-V ratings and a true open-drain, power-good function.
In addition to the basic functions of detection, classification and undervoltage lockout (UVLO), these controllers
include an adjustable inrush limiting feature. The TPS2375 has 802.3af compliant UVLO limits, the TPS2377 has
legacy UVLO limits, and the TPS2376 has a programmable UVLO with a dedicated input pin.
The TPS2375 family specifications incorporate a voltage offset of 1.5 V between its limits and the IEEE 802.3af
specifications to accommodate the required input diode bridges used to make the PD polarity insensitive.
Additional resources can be found on the TI Web site www.ti.com.
RJ−45
1
TX
Pair
Detect
Data to
Ethernet
PHY
2
7
8
100 mF,
100 V
VDD
CLASS
R(ICLASS)
357 W,
1%
Spare
Pair
Data to
Ethernet PHY
VRTN
RTN
3
RX
Pair
V (PG-RTN)
TO DC/DC
CONVERTER
ILIM
R(ILIM)
178 kW,
1%
Class 3
Current
100
kW
PG
DET
VSS
Spare
Pair
0.1mF,
100 V
10 %
R(DET)
24.9 kW,
1%
TPS2375
SMAJ58A
4
5
VDD
Input
Current
DF01S
2 Places
Classify Power Up & Inrush
Note: Class 3 PD Depicted.
PG Pullup Resistor Is Optional.
Note: All Voltages With Respect to VSS.
6
Figure 1. Typical Application Circuit and Startup Waveforms
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2008, Texas Instruments Incorporated
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
AVAILABLE OPTIONS
-40°C to 85°C
(1)
PACKAGE (1)
UVLO THRESHOLDS (NOMINAL)
TA
TYPE
LOW
HIGH
SO-8
TSSOP-8
MARKING
802.3af
30.5 V
39.3 V
TPS2375D
TPS2375PW
2375
Adjustable
1.93 V
2.49 V
TPS2376D
TPS2376PW
2376
Legacy
30.5 V
35.1 V
TPS2377D
TPS2377PW
2377
Add an R suffix to the device type for tape and reel.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
(1)
, voltages are referenced to V(VSS)
TPS237x
VDD, RTN, DET, PG
Voltage
-0.3 V to 100 V
ILIM, UVLO
-0.3 V to 10 V
CLASS
-0.3 V to 12 V
RTN
Current, sinking
(2)
(3)
0 to 515 mA
PG
Current, sourcing
0 to 5 mA
DET
0 to 1 mA
CLASS
0 to 50 mA
ILIM
0 to 1 mA
Human body model
ESD
2 kV
Charged device model
500 V
System level (contact/air) at RJ-45 (4)
8/15 kV
TJ
Maximum junction temperature range
Internally limited
Tstg
Storage temperature range
-65°C to 150°C
(1)
(2)
(3)
(4)
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds - Green Packages
260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds - Nongreen Packages
235°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
I(RTN) = 0
SOA limited to V(RTN) = 80 V and I(RTN) = 515 mA.
Surges applied to RJ-45 of Figure 1 between pins of RJ-45, and between pins and output voltage rails per EN61000-4-2, 1999.
DISSIPATION RATING TABLE (1)
θJA (LOW-K)
°C/W
θJA (HIGH-K)
°C/W
POWER RATING
(HIGH-K)
TA = 85°C
mW
D (SO-8)
238
150
266
PW (TSSOP-8)
258.5
159
251
PACKAGE
(1)
2
Tested per JEDEC JESD51. High-K is a (2 signal – 2 plane) test board and low-K is a double sided
board with minimum pad area and natural convection.
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
VDD, PG, RTN
0
57
UVLO
0
5
Operating current range (sinking)
RTN
0
350
Classification resistor (1)
CLASS
Input voltage range
R(ILIM)
Inrush limit program resistor
(1)
Sinking current
UNIT
V
V
mA
255
4420
Ω
62.5
500
kΩ
0
2
mA
PG
TJ
Operating junction temperature
-40
125
°C
TA
Operating free–air temperature
-40
85
°C
(1)
Voltage should not be eternally applied to CLASS and ILIM.
ELECTRICAL CHARACTERISTICS
V(VDD) = 48 V, R(DET) = 24.9 kΩ, R(CLASS) = 255 Ω, R(ILIM) = 178 kΩ, and –40°C ≤ TJ ≤ 125°C, unless otherwise noted. Positive
currents are into pins. V(UVLO) = 0 V for classification and V(UVLO) = 5 V otherwise for the TPS2376. Typical values are at 25°C.
All voltages are with respect to VSS unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
0.3
3
µA
4
12
µA
0.1
5
µA
DETECTION
Offset current
DET open, V(VDD) = V(RTN) = 1.9 V, measure
I(VDD) + I(RTN)
Sleep current
DET open, V(VDD) = V(RTN) = 10.1 V, measure
I(VDD) + I(RTN)
DET leakage current
V(DET) = V(VDD) = 57 V, measure I(DET)
Detection current
V(RTN) = V(VDD),
R(DET) = 24.9 kΩ,
measure I(VDD) + I(RTN) +
I(DET)
V(VDD) = 1.4 V
53.7
56
58.3
µA
V(VDD) = 10.1 V
395
410
417
µA
CLASSIFICATION
I(CLASS)
V(CL_ON)
V(CU_OFF)
V(CU_H)
Classification current (1)
Classification lower threshold
Classification upper threshold
R(CLASS) = 4420 Ω, 13 ≤ V(VDD) ≤ 21 V
2.2
2.4
2.8
R(CLASS) = 953 Ω, 13 ≤ V(VDD) ≤ 21 V
10.3
10.6
11.3
R(CLASS) = 549 Ω, 13 ≤ V(VDD) ≤ 21 V
17.7
18.3
19.5
R(CLASS) = 357 Ω, 13 ≤ V(VDD) ≤ 21 V
27.1
28.0
29.5
R(CLASS) = 255 Ω, 13 ≤ V(VDD) ≤ 21 V
38.0
39.4
41.2
Regulator turns on, V(VDD) rising
10.2
11.3
13.0
V
Regulator turns off, V(VDD) rising
21
21.9
23
V
Hysteresis
0.5
0.78
1
V
1
µA
1.0
Ω
mA
Leakage current
V(CLASS) = 0 V, V(VDD) = 57 V
On resistance
I(RTN) = 300 mA
Leakage current
V(VDD) = V(RTN) = 30 V,
V(UVLO) = 0 V (TPS2376)
Current limit
V(RTN) = 1 V
405
461
515
mA
Inrush limit
V(RTN) = 2 V, R(ILIM) = 178 kΩ
100
130
180
mA
Inrush current termination
V(RTN) falling, R(ILIM) = 178 kΩ, inrush
state→normal operation
85%
91%
100%
15
25
PASS DEVICE
rDS(on)
I(LIM)
(1)
(2)
(2)
Current rise time into inrush
R(ILIM) = 69.8 kΩ, V(RTN-VSS) = 5 V,
I(RTN) = 30 mA→300 mA, V(VDD) increasing
past upper UVLO
Current limit response time
Apply load ∞Ω→20 Ω, time measured to
I(RTN) = 45 mA
Leakage current, ILIM
V(VDD) = 15 V, V(UVLO) = 0 V
0.58
15
µA
µs
2
2.5
1
µs
µA
Classification is tested with exact resistor values. A 1% tolerance classification resistor assures compliance with IEEE 802.3af limits.
This parameter specifies the RTN current value, as a percentage of the steady state inrush current, below which it must fall to make PG
assert (open-drain).
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
3
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
V(VDD) = 48 V, R(DET) = 24.9 kΩ, R(CLASS) = 255 Ω, R(ILIM) = 178 kΩ, and –40°C ≤ TJ ≤ 125°C, unless otherwise noted. Positive
currents are into pins. V(UVLO) = 0 V for classification and V(UVLO) = 5 V otherwise for the TPS2376. Typical values are at 25°C.
All voltages are with respect to VSS unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PG
Latchoff voltage threshold rising
V(RTN) rising
9.5
10.0
10.5
V
PG deglitch
Delay rising and falling PG
75
150
225
µs
I(PG) = 2 mA, V(RTN) = 34 V,
V(VDD) = 38 V, V(RTN) falling
0.12
0.4
I(PG) = 2 mA, V(RTN) = 0 V, V(VDD) = 25 V, for
TPS2376 V(UVLO) = 0 V
0.12
0.4
0.1
1
Output low voltage
Leakage current
V(PG) = 57 V, V(RTN) = 0 V
V
V
µA
UVLO
V(UVLO_R)
V(UVLO_F)
TPS2375 Voltage at VDD
V(VDD) rising
38.4
39.3
40.4
V(VDD) falling
29.6
30.5
31.5
8.3
8.8
9.1
V(VDD) rising
2.43
2.49
2.57
V(VDD) falling
1.87
1.93
1.98
Hysteresis
0.53
0.56
0.58
V(VDD) rising
34.1
35.1
36.0
V(VDD) falling
29.7
30.5
31.4
4.3
4.5
4.8
Hysteresis
TPS2376 Voltage at UVLO
TPS2377 Voltage at VDD
Hysteresis
TPS2376 Input leakage, UVLO
V(UVLO) = 0 V to 5 V
-1
1
V
V
V
µA
THERMAL SHUTDOWN
Shutdown temperature
Temperature rising
°C
135
Hysteresis
°C
20
BIAS CURRENT
Operating current
4
Submit Documentation Feedback
I(VDD)
240
450
µA
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
DEVICE INFORMATION
FUNCTIONAL BLOCK DIAGRAM
12 V
VDD
8
DET
3
Detection
Comparator
+
−
22 V
CLASS
2
10 V
Regulator
Classification
Comparator
+
PG
6
PG Comparator
−
1.5 V
& 10 V
Delay
150 mS
−
+
S
R
Q
0 = Fault
0 = Inrush
S
R
2.5 V
UVLO
’76 Only
7
ILIM
1
UVLO
Comp.
−
RTN
5
Thermal Shutdown,
Counter, and Latch
+
See
Note
2.5 V
+
Q
1 = Limiting
Current
Mirror
45 mV 1
1:1
0
−
+
−
EN
Current
Limit Amp.
800 W
0.08 W
VSS
4
Note: For the TPS2376, the UVLO comparator connects to the UVLO pin and not to the UVLO divider.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
5
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
TERMINAL FUNCTIONS
PIN NAME
PIN NUMBER
I/O
DESCRIPTION
1
O
Connect a resistor from ILIM to VSS to set the start-up inrush current limit.
The equation for calculating the resistor is shown in the detailed pin
description section for ILIM.
2
2
O
Connect a resistor from CLASS to VSS to set the classification of the
powered device (PD). The IEEE classification levels and corresponding
resistor values are shown in Table 1.
DET
3
3
O
Connect a 24.9-kΩ detection resistor from DET to VDD for a valid PD
detection.
VSS
4
4
I
Return line on the source side of the TPS2375 from the PSE.
RTN
5
5
O
Switched output side return line used as the low-side reference for the
TPS2375 load.
PG
6
6
O
Open-drain, power-good output; active high.
UVLO
-
7
I
Used only on the TPS2376. Connect a resistor divider from VDD to VSS to
implement the adjustable UVLO feature of the TPS2376.
NC
7
-
VDD
8
8
TPS2375/77
TPS2376
ILIM
1
CLASS
No connection
I
Positive line from the rectified PSE provided input.
Detailed Pin Description
The following descriptions refer to the schematic of Figure 1 and the functional block diagram.
ILIM: A resistor from this pin to VSS sets the inrush current limit per Equation 1:
I
+ 25000
(LIM)
R
(ILIM)
(1)
where ILIM is the desired inrush current value, in amperes, and R(ILIM) is the value of the programming resistor
from ILIM to VSS, in ohms. The practical limits on R(ILIM) are 62.5 kΩ to 500 kΩ. A value of 178 kΩ is
recommended for compatibility with legacy PSEs.
Inrush current limiting prevents current drawn by the bulk capacitor from causing the line voltage to sag below
the lower UVLO threshold. Adjustable inrush current limiting allows the use of arbitrarily large capacitors and also
accommodates legacy systems that require low inrush currents.
The ILIM pin must not be left open or shorted to VSS.
CLASS: Classification is implemented by means of an external resistor, R(CLASS), connected between CLASS
and VSS. The controller draws current from the input line through R(CLASS) when the input voltage lies between
13 V and 21 V. The classification currents specified in the electrical characteristics table include the bias current
flowing into VDD and any RTN leakage current.
Table 1. CLASSIFICATION
CLASS
PD POWER (W)
R(CLASS) (Ω)
802.3af LIMITS (mA)
0
0.44 – 12.95
4420 ±1%
0-4
1
0.44 – 3.84
953 ±1%
9 - 12
2
3.84 – 6.49
549 ±1%
17 - 20
3
6.49 – 12.95
357 ±1%
26 - 30
4
-
255 ±1%
36 - 44
NOTE
Default class
Reserved for future use
The CLASS pin must not be shorted to ground.
DET: Connect a resistor, R(DET), between DET and VDD. This resistor should equal 24.9 kΩ, ±1% for most
applications. R(DET) is connected across the input line when V(VDD) lies between 1.4 V and 11.3 V, and is
disconnected when the line voltage exceeds this range to conserve power. This voltage range has been chosen
to allow detection with two silicon rectifiers between the controller and the RJ-45 connector.
VSS: This is the input supply negative rail that serves as a local ground to the TPS2375.
6
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
RTN: This pin provides the switched negative power rail used by the downstream circuits. The operational and
inrush current limit control current into the pin. The PG circuit monitors the RTN voltage and also uses it as the
return for the PG pin pulldown transistor. The internal MOSFET body diode clamps VSS to RTN when voltage is
present between VDD and RTN and the PoE input is not present.
PG: This pin goes to a high resistance state when the internal MOSFET that feeds the RTN pin is enabled, and
the device is not in inrush current limiting. In all other states except detection, the PG output is pulled to RTN by
the internal open-drain transistor. Performance is assured with at least 4 V between VDD and RTN.
PG is an open-drain output; therefore, it may require a pullup resistor or other interface.
UVLO: This pin is specific to the TPS2376; it is not internally connected on the TPS2375 and TPS2377. The
UVLO pin is used with an external resistor divider between VDD and VSS to set the upper and lower UVLO
thresholds. The hysteresis, as measured as a percentage of the upper UVLO, is the same as the TPS2375.
The TPS2376 enables the output when V(UVLO) exceeds the upper UVLO threshold. When current begins to flow,
VDD sags due to cable resistance and the dynamic resistance of the input diodes. The lower UVLO threshold
must be below the lowest voltage that the input reaches.
The TPS2376 implements adjustable UVLO thresholds, but is otherwise functionally equivalent to the TPS2375.
The TPS2375 offers fixed UVLO thresholds designed to maximize hysteresis while maintaining compatibility with
the IEEE 802.3af standard. The TPS2377 offers fixed UVLO thresholds optimized for use with legacy PoE
systems.
VDD: This is the positive input supply to the TPS2375, which is also common to downstream load circuits. This
pin provides operating power and allows the controller to monitor the line voltage to determine the mode of
operation.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
7
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS
Graphs over temperature are interpolations between the marked data points.
I(VDD) + I(RTN) IN DETECTION
6
11.3
30
Resistance − k Ω
TA = 125°C
4
TA = 25°C
3
Classification Turnon Voltage − V
35
5
Current − µ A
CLASSIFICATION TURNON
VOLTAGE
vs
TEMPERATURE
PD DETECTION RESISTANCE
vs
V(PI)
2
25
20
Specification Limits
15
1
11.2
11.1
TA = −40°C
0
0
1
2
3
4
5
6
7
8
9
10
10 11
1
3
5
V(VDD) − V
9
11.0
11
−40 −20
0
20
40
60
80
100 120
TA − Free-Air Temperature − °C
V(PI) − V
Figure 2.
Figure 3.
Figure 4.
CLASSIFICATION TURNOFF
VOLTAGE
vs
TEMPERATURE
I(VDD) CURRENT
vs
VDD
PASS DEVICE
RESISTANCE
vs
TEMPERATURE
21.94
0.9
0.350
0.300
21.93
21.92
0.250
Pass Device Resistance − Ω
TA = 125°C
I (VDD) − mA
Classification Turnoff Voltage − V
7
TA = 25°C
TA = −40°C
0.200
21.91
0.150
21.90
−40 −20
0
20
40
60
80
100
0.100
22
120
TA − Free-Air Temperature − °C
27
32
37
42
47
52
0.8
0.7
0.6
0.5
0.4
−40 −20
57
0
20
40
60
80
Figure 5.
Figure 6.
Figure 7.
TPS2375
UVLO RISING
vs
TEMPERATURE
TPS2375
UVLO FALLING
vs
TEMPERATURE
TPS2376
UVLO RISING
vs
TEMPERATURE
39.5
100 120
TA − Free-Air Temperature − °C
VDD − V
30.60
2.489
30.56
2.488
V (UVLO) − V
VDD − V
VDD − V
39.4
30.52
30.48
39.3
39.2
−40 −20
0
20
40
60
80
100 120
TA − Free-Air Temperature − °C
Figure 8.
8
Submit Documentation Feedback
2.487
2.486
30.44
2.485
30.40
−40 −20 0
20 40 60 80 100 120
TA − Free-Air Temperature − °C
2.484
−40 −20
Figure 9.
0
20
40
60
80
100 120
TA − Free-Air Temperature − °C
Figure 10.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
TYPICAL CHARACTERISTICS (continued)
Graphs over temperature are interpolations between the marked data points.
TPS2376
UVLO FALLING
vs
TEMPERATURE
TPS2377
UVLO RISING
vs
TEMPERATURE
1.929
35.20
1.928
35.15
TPS2377
UVLO FALLING
vs
TEMPERATURE
30.65
1.926
35.10
VDD − V
VDD − V
V (UVLO) − V
30.60
1.927
30.55
35.05
1.925
30.50
35.00
1.924
1.923
−40 −20
34.95
0
20
40
60
80
100 120
0
20
40
60
80
30.45
−40 −20
100 120
0
20
40
60
80
100 120
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
Figure 11.
Figure 12.
Figure 13.
INRUSH STATE TERMINATION
THRESHOLD
vs
TEMPERATURE
INRUSH CURRENT
vs
TEMPERATURE
CURRENT LIMIT
vs
TEMPERATURE
440
350
94.0
75 kΩ
325
93.5
300
93.0
275
92.5
92.0
435
I (RTN) − mA
I (ILIM) − mA
Percent of Inrush Limit Current
−40 −20
250
225
125 kΩ
200
175
91.5
178 kΩ
150
91.0
430
125
90.5
−40 −20
0
20
40
60
80
100
−40 −20
100 120
0
20
40
60
80
100 120
425
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
−40 −20 0
20 40 60 80 100 120
TA − Free-Air Temperature − °C
Figure 14.
Figure 15.
Figure 16.
PG DEGLITCH PERIOD
vs
TEMPERATURE
PG Deglitch Period − µs
180
160
140
120
−40 −20
0
20
40
60
80
100 120
TA − Free-Air Temperature − °C
Figure 17.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
9
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
APPLICATION INFORMATION
OVERVIEW
The IEEE 802.3af specification defines a process for safely powering a PD over a cable, and then removing
power if a PD is disconnected. The process proceeds through three operational states: detection, classification,
and operation. The intent behind the process is to leave an unterminated cable unpowered while the PSE
periodically checks for a plugged-in device; this is referred to as detection. The low power levels used during
detection are unlikely to cause damage to devices not designed for PoE. If a valid PD signature is present, then
the PSE may optionally inquire how much power the PD requires; this is referred to as classification. The PD
may return a default full-power signature, or one of four other choices. Knowing the power demand of each PD
allows the PSE to intelligently allocate power between PDs, and also to protect itself against overload. The PSE
powers up a valid PD, and then monitors its output for overloads. The maintain power signature (MPS) is
presented by the powered PD to assure the PSE that it is there. The PSE monitors its output for the MPS to see
if the PD is removed, and turns the port off, if it loses the MPS. Loss of MPS returns the PSE to the initial state of
detection. Figure 18 shows the operational states as a function of PD input voltage range.
The PD input is typically an RJ-45 (8-pin) connector, referred to as the power interface (PI). PD input
requirements differ from PSE output requirements to account for voltage drops in the cable and margin. The
specification uses a cable resistance of 20 Ω to derive the voltage limits at the PD from the PSE output
requirements. Although the standard specifies an output power of 15.4 W at the PSE output, there is only
12.95 W available at the input of the PD due to the worst case power loss in the cable.
The PSE can apply voltage either between the RX and TX pairs, or between the two spare pairs as shown in
Figure 1. The applied voltage can be of either polarity. The PSE cannot apply voltage to both paths at the same
time. The PD uses input diode bridges to accept power from any of the possible PSE configurations. The voltage
drops associated with the input bridges cause a difference between the IEEE 802.3af limits at the PI and the
TPS2375 specifications.
The PSE is required to current limit between 350 mA and 400 mA during normal operation, and it must
disconnect the PD if it draws this current for more than 75 ms. The PSE may set lower output current limits
based on the PD advertised power requirements, as discussed below.
2.7
10.1
14.5
20.5
30
Maximum Input
Voltage
Must Turn On by−
Voltage Rising
Lower Limit −
Proper Operation
Must Turn Off by −
Voltage Falling
Shut down
Classify
Detect
0
Classification
Upper Limit
Classification
Lower Limit
Detection
Upper Limit
Detection
Lower Limit
The following discussion is intended as an aid in understanding the operation of the TPS2375, but not as a
substitute for the actual IEEE 802.3af standard. Standards change and should always be referenced when
making design decisions.
Normal Operation
36
42
57
PI Voltage (V)
Figure 18. IEEE 802.3 PD Limits
INTERNAL THRESHOLDS
In order to implement the PoE functionality as shown in Figure 18, the TPS2375 has a number of internal
comparators with hysteresis for stable switching between the various states. Figure 19 relates the parameters in
the Electrical Characteristics section to the PoE states. The mode labeled idle between classification and
detection implies that the DET, CLASS, PG, and RTN pins are all high impedance.
10
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
Operational Mode
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
PD Powered
Idle
Classification
Detection
V(VDD)
V(CU_H)
1.4V
V(CL_ON)
V(UVLO_F)
V(UVLO_R)
V(CU_OFF)
Figure 19. Threshold Voltages
DETECTION
This feature of IEEE 802.3af eliminates powering and potentially damaging Ethernet devices not intended for
application of 48 V. When a voltage in the range of 2.7 V to 10.1 V is applied to the PI, an incremental resistance
of 25 kΩ signals the PSE that the PD is capable of accepting power. A PD that is capable of accepting power,
but is not ready, may present an incorrect signature intentionally. The incremental resistance is measured by
applying two different voltages to the PI and measuring the current it draws. These two test voltages must be
within the specified range and be at least 1 V apart. The incremental resistance equals the difference between
the voltages divided by the difference between the currents. The allowed range of resistance is 23.75 kΩ to
26.25 kΩ.
The TPS2375 is in detection mode whenever the supply voltage is below the lower classification threshold. The
TPS2375 draws a minimum of bias power in this condition, while PG and RTN are high impedance and the
circuits associated with ILIM and CLASS are disabled. The DET pin is pulled to ground during detection. Current
flowing through R(DET) to VSS (Figure 1) produces the detection signature. For most applications, a 24.9-kΩ, 1%,
resistor is recommended. R(DET) can be a small, low-power resistor because it only sees a stress of about 5 mW.
When the input voltage rises above the 11.3 V lower classification comparator threshold, the DET pin goes to an
open-drain condition to conserve power.
The input diode bridge incremental resistance can be hundreds of ohms at the low currents seen at 2.7 V on the
PI. The bridge resistance is in series with R(DET) and increases the total resistance seen by the PSE. This varys
with the type of diode selected by the designer, and it is not usually specified on the diode data sheet. The value
of R(DET) may be adjusted downwards to accommodate a particular diode type.
CLASSIFICATION
Once the PSE has detected a PD, it may optionally classify the PD. This process allows a PSE to determine the
PD power requirements in order to allot only as much power as necessary from its fixed input power source. This
allows the PSE to power the maximum number of PDs from a particular power budget. This step is optional
because some PSEs can afford to allot the full power to every powered port.
The classification process applies a voltage between 14.5 V and 20.5 V to the input of the PD, which in turn
draws a fixed current set by R(CLASS). The PSE measures the PD current to determine which of the five available
classes (Table 1) that the PD is signalling. The total current drawn from the PSE during classification is the sum
of bias currents and current through R(CLASS). The TPS2375 disconnects R(CLASS) at voltages above the
classification range to avoid excessive power dissipation (Figure 18 and Figure 19).
The value of R(CLASS) should be chosen from the values listed in Table 1 based on the average power
requirements of the PD. The power rating of this resistor should be chosen so that it is not overstressed for the
required 75-ms classification period, during which 10 V is applied. The PD could be in classification for extended
periods during bench test conditions, or if an auxiliary power source with voltage within the classification range is
connected to the PD front end. Thermal protection may activate and turn classification off if it continues for more
than 75 ms, but the design must not rely on this function to protect the resistor.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
11
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
UNDERVOLTAGE LOCKOUT (UVLO)
The TPS2375 incorporates an undervoltage lockout (UVLO) circuit that monitors line voltage to determine when
to apply power to the downstream load and allow the PD to power up. The IEEE 802.3af specification dictates a
maximum PD turnon voltage of 42 V and a minimum turnoff voltage of 30 V (Figure 19). The IEEE 802.3af
standard assumes an 8-V drop in the cabling based on a 20-Ω feed resistance and a 400-mA maximum inrush
limit. Because the minimum PSE output voltage is 44 V, the PD must continue to operate properly with input
voltages as low as 36 V. The TPS2375 UVLO limits are designed to meet the turnon, turnoff, and hysteresis
requirements.
Various legacy PSE systems in the field do not meet the minimum output voltage of 44 V. The TPS2377 UVLO
limits are designed to support these systems with a lower turnon voltage and smaller hysteresis. Although the
TPS2377 works with compliant PSEs, it could potentially exhibit startup instabilities if the PSE output voltage
rises slowly. The TPS2375 is recommended for applications with compliant PSEs.
In order to provide flexibility for noncompliant designs, the TPS2376 allows the designer to program the turnon
thresholds with a resistor divider. The hysteresis of the TPS2376, measured as a percentage of the turnon
voltage, is similar to that of the TPS2375. To use the TPS2376, connect a resistor divider between VDD and
VSS with the tap connected to the UVLO pin. The total divider resistance appears in parallel with the R(DET), and
the combination of the two should equal 24.9 kΩ. The divider ratio should be chosen to obtain 2.5 V at the UVLO
pin when V(VDD) is at the desired turnon voltage.
The TPS2375 uses the UVLO function to control the load through an onboard MOSFET switch. Figure 19
graphically shows the relationships of the UVLO thresholds defined in the Electrical Characteristics section to the
TPS2375 operational states.
PROGRAMMABLE INRUSH CURRENT LIMIT AND FIXED OPERATIONAL CURRENT LIMIT
Inrush limiting is beneficial for a number of reasons. First, it provides a mechanism to keep the inrush current
below the 400 mA, 50 ms, maximum inrush allowed by the standard. Second, by reducing the level of the current
limit below the PSE operational limit, which can be as low as the classification power divided by the PSE voltage,
it allows an arbitrarily large bulk capacitor to be charged. Third, some legacy PSEs may not tolerate large inrush
currents while powering their outputs up.
The TPS2375 operational current limit protects the internal power switch from instantaneous output faults and
current surges. The minimum operational current limit level of 405 mA is above the maximum PSE output current
limit of 400 mA. This current limit allows the PD to draw the maximum available power and also allows the PSE
to detect fault conditions.
The TPS2375 incorporates a state machine that controls the inrush and operational current limit states. When
V(VDD) is below the lower UVLO threshold, the current limit state machine is reset. In this condition, the RTN pin
is high impedance, and at V(VDD) once the output capacitor is discharged by the downstream circuits. When
V(VDD) rises above the UVLO turnon threshold, the TPS2375 enables the internal power MOSFET with the
current limit set to the programmed inrush value. The load capacitor charges and the RTN pin voltage falls from
V(VDD) to nearly V(VSS). Once the inrush current falls about 10% below the programmed limit, the current limit
switches to the internal 450-mA operational level after a 150-µs delay. This switchover can be seen in the
operation of PG, which goes active (open drain) after inrush terminates as seen in Figure 1. The internal power
MOSFET is disabled if the input voltage drops below the lower UVLO threshold.
When in the operating current-limit state, a fault on the output or a large input transient can cause the internal
MOSFET to limit current. The RTN voltage rises above its normal operating level of less than 0.5 V while in
current-limit state. If V(RTN) rises above 10 V for more than 150 µs, the MOSFET is latched off. The PD input
voltage must drop below the lower UVLO threshold to clear this latch. If the RTN voltage does not exceed 10 V
while in current-limit state, but the condition persists long enough to overheat the TPS2375, the thermal limit
circuit activates, as described in the thermal protection section.
Practical values of R(ILIM) lie between 62.5 kΩ and 500 kΩ. The pin must not be left open. An inrush level of
140 mA, set by an R(ILIM) of 178 kΩ, should be used with TPS2377 applications for compatibility with legacy
systems. This same inrush current level suffices for many TPS2375 applications.
The inrush limit, the bulk capacitor size, and the downstream dc/dc converter startup method must be chosen so
that the converter input current does not exceed the inrush current limit while it is active. This can be achieved by
using the PG output to enable the downstream converter after inrush finishes, by delaying the converter startup
until inrush finishes, or by increasing the value of the inrush current limit.
12
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
MAINTAIN POWER SIGNATURE
Once a valid PD has been detected and powered, the PSE uses the maintain power signature (MPS) to
determine when to remove power from the PI. The PSE removes power from that output port if it detects loss of
MPS for 300 ms or more. A valid MPS requires the PD to draw at least 10 mA and also have an ac impedance
less than 26.25 kΩ in parallel with 0.05 µF. TI's reference designs meet the requirements necessary to maintain
power.
POWER GOOD
The TPS2375 includes a power-good circuit that can be used to signal the PD circuitry that the load capacitor is
fully charged. This pin is intended for use as an enable signal for downstream circuitry. If the converter tries to
start up while inrush is active, and draws a current equal to the inrush limit, a latchup condition occurs in which
the PD never successfully starts. Using the PG pin is the safest way to assure that there are no undesired
interactions between the inrush limit, the converter startup characteristic, and the size of the bulk capacitor.
The PG pin goes to an open-drain state approximately 150 µs after the inrush current falls 10% below the
regulated value. PG pulldown current is only assured when the voltage difference between VDD and RTN
exceeds 4 V. This is not a limiting factor because the dc/dc converter should not be able to run from 4 V. The PG
output is pulled to RTN whenever the MOSFET is disabled or is in inrush current limiting.
Referencing PG to RTN simplifies the interface to the downstream dc/dc converter or other circuit because it is
referenced to RTN, not VSS. Care must be used in interfacing the PG pin to the downstream circuits. The pullup
to VDD shown in Figure 1 may not be appropriate for a particular dc/dc converter interface. The PG pin connects
to an internal open-drain, 100-V transistor capable of sinking 2 mA to a voltage below 0.4 V. The PG pin can be
left open if it is not used.
THERMAL PROTECTION
The controller may overheat after operation in current-limit state or classification for an extended period of time,
or if the ambient temperature becomes excessive. The TPS2375 protects itself by disabling the RTN and CLASS
pins when the internal die temperature reaches about 140°C. It automatically restarts when the die temperature
has fallen approximately 20°C. If this cycle occurs eight times, then the device latches off until the supply voltage
drops below the lower classification threshold. This feature prevents the part from operating indefinitely in fault,
and ensures that the PSE recognizes the fault condition when using dc MPS. Thermal protection is active
whenever the TPS2375 is not in detection.
Figure 20 shows how the TPS2375 responds when it is enabled into a short. The TPS2375 starts in the inrush
current-limit state when the input voltage exceeds the upper UVLO limit. A power dissipation of over 5 W heats
the die from 25°C to 140°C in approximately 400 ms. The TPS2375 then shuts down until the die temperature
drops to about 120°C, which occurs in about 20 ms. This process repeats eight times before the TPS2375
latches off. The PG pin is high because RTN is tied to VDD.
V(PI) = 44 V, R(ILIM) = 178 kW
Ch1: VDD @ 50 V/div
CH2: RTN @ 50 V/div
CH3: V(PG) @ 50 V/div
Iin @ 100 mA/div
Figure 20. TPS2375 Started Into Short
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
13
data sheet
TPS2375
TPS2376
TPS2377
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
POWER SYSTEM DESIGN
The PSE is a power and current limited source, which imposes certain constraints on the PD power supply
design. DC/DC converters have both a constant input power characteristic that causes them to draw high
currents at low voltage, and they tend to go to a full input power mode during start-up that is often 25% or more
above their rated power. Improper design of the power system can cause the PD to not start up with all
combinations of Ethernet lines and PSE sources.
The following guidelines should be used:
1. Set the TPS2375 inrush to a moderate value as previously discussed.
2. Hold the dc/dc converter off during inrush as previously discussed.
3. The converter should have a softstart that keeps the peak input start-up current below 400 mA, and
preferably only a modest amount over the operating current, with a 44-V PSE source and a 20-Ω loop.
4. If step 3 cannot be met, the bulk input capacitor should not discharge more than 8 V during converter start
up from a 400-mA limited, 44-V source with a 20-Ω line. Start-up must be completed in less than 50 mS
Step 4 requires a balance between the converter output capacitance, load, and input bulk capacitance. While
there are some cases which may not require all these measures, such as a 1-W PD with minimal converter
output capacitance, it is always a good practice to follow them.
AUXILIARY POWER SOURCE ORING
Many PoE capable devices are designed to operate from either a wall adapter or PoE power. A local power
solution adds cost and complexity, but allows a product to be used regardless of PoE availability. Attempting to
create solutions where the two power sources coexist in a specific controlled manner results in additional
complexity, and is not generally recommended. Figure 21 demonstrates three methods of diode ORing external
power into a PD. Option 1 inserts power on the output side of the PoE power conversion. Option 2 inserts power
on the TPS2375 output. Option 3 applies power to the TPS2375 input. Each of these options has advantages
and disadvantages. The wall adapter must meet a minimum 1500-Vac dielectric withstand test voltage to the ac
input power and to ground for options 2 and 3.
Inserting a Diode in This Location
With Option 2, Allows PoE To Start
With Aux Power Present.
~ +
VDD
R (DET)
0.1 µF
DET
Option 3
Auxiliary
Power
Input
Option 2
Use only
one option
Option 1
DC/DC
Converter
Main
DC/DC
Converter
Output
UCC3809
or
UCC3813
CLASS
VSS
~ −
SMAJ58A
~ +
ILIM
R(ILIM)
22 µF
TPS237X
RJ−45
~ −
RTN
R (CLASS)
For Option 2,
The Capacitor Must Be
Right At The Output
To Control The
Transients.
Optional
Regulator
A Full Wave Bridge
Gives Flexibility To
Use Supply With Either
Polarity
See TI Document SLVR030 For A Typical
Application Circuit.
Figure 21. Auxiliary Power ORing
14
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
data sheet
TPS2375
TPS2376
TPS2377
www.ti.com............................................................................................................................................................ SLVS525B – APRIL 2004 – REVISED APRIL 2008
Option 1 consists of ORing power to the output of the PoE dc/dc converter. This option is preferred in cases
where PoE is added to an existing design that uses a low-voltage wall adapter. The relatively large PD
capacitance reduces the potential for harmful transients when the adapter is plugged in. The wall adapter output
may be grounded if the PD incorporates an isolated converter. This solution requires two separate regulators, but
low-voltage adapters are readily available. The PoE power can be given priority by setting its output voltage
above that from the auxiliary source.
Option 2 has the benefits that the adapter voltage may be lower than the TPS2375 UVLO, and that the bulk
capacitor shown can control voltage transients caused by plugging an adapter in. The capacitor size and location
are chosen to control the amount of ringing that can occur on this node, which can be affected by additional
filtering components specific to a dc/dc converter design. The optional diode blocks the adapter voltage from
reverse biasing the input, and allows a PoE source to apply power provided that the PSE output voltage is
greater than the adapter voltage. The penalty of the diode is an additional power loss when running from PSE
power. The PSE may not be able to detect and start powering without the diode. This means that the adapter
may continue to power the PD until removed. Auxiliary voltage sources can be selected to be above or below the
PoE operational voltage range. If automatic PoE precedence is desired when using the low-voltage auxiliary
source option, make sure that the TPS2375 inrush program limit is set higher than the maximum converter input
current at its lowest operating voltage. It is difficult to use PG with the low-voltage auxiliary source because the
converter must operate during a condition when the TPS2375 would normally disable it. Circuits may be
designed to force operation from one source or the other depending on the desired operation and the auxiliary
source voltage chosen. However, they are not recommended because they increase complexity and thus cost.
Option 3 inserts the power before the TPS2375. It is necessary for the adapter to meet the TPS2375 UVLO
turnon requirement and to limit the maximum voltage to 57 V. This option provides a valid power-good signal and
simplifies power priority issues. The disadvantage of this method is that it is the most likely to cause transient
voltage problems. Plugging a powered adapter in applies a step input voltage to a node that has little
capacitance to control the dv/dt and voltage ringing. If the wall mount supply applies power to the PD before the
PSE, it prevents the PSE from detecting the PD. If the PSE is already powering the PD when the auxiliary source
is plugged in, priority is given to the higher supply voltage.
ESD
The TPS2375 has been tested using the surge of EN61000-4-2 in an evaluation module (EVM) using the circuit
in Figure 1. The levels used were 8-kV contact discharge and 15-kV air discharge. Surges were applied between
the RJ-45 and the dc EVM outputs, and between an auxiliary power input jack and the dc outputs. No failures
were observed.
ESD requirements for a unit that incorporates the TPS2375 have much broader scope and operational
implications than those used in TI’s testing. Unit level requirements should not be confused with EVM testing that
only validated the TPS2375.
EXTERNAL COMPONENTS
Transformer
Nodes on an Ethernet network commonly interface to the outside world via an isolation transformer per IEEE
802.3 requirements, see Figure 1. For powered devices, the isolation transformer must include a center tap on
the media (cable) side. Proper termination is required around the transformer to provide correct impedance
matching and to avoid radiated and conducted emissions. Transformers must be specifically rated to work with
the Ethernet chipset, and the IEEE 802.3af standard.
Input Diodes or Diode Bridges
The IEEE 802.3af requires the PD to accept power on either set of input pairs in either polarity. This requirement
is satisfied by using two full-wave input bridge rectifiers as shown in Figure 1. Silicon p-n diodes with a 1-A or
1.5-A rating and a minimum breakdown of 100 V are recommended. Diodes exhibit large dynamic resistance
under low-current operating conditions such as in detection. The diodes should be tested for their behavior under
this condition. The diode forward drops must be less than 1.5 V at 500 µA and at the lowest operating
temperature.
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
Submit Documentation Feedback
15
TPS2375
TPS2376
TPS2377
data sheet
SLVS525B – APRIL 2004 – REVISED APRIL 2008............................................................................................................................................................ www.ti.com
Input Capacitor
The IEEE 802.3af requires a PD input capacitance between 0.05 µF and 0.12 µF during detection. This capacitor
should be located directly adjacent to the TPS2375 as shown in Figure 1. A 100-V, 10%, X7R ceramic capacitor
meets the specification over a wide temperature range.
Load Capacitor
The IEEE 802.3af specification requires that the PD maintain a minimum load capacitance of 5 µF. It is
permissible to have a much larger load capacitor, and the TPS2375 can charge in excess of 470 µF before
thermal issues become a problem. However, if the load capacitor is too large, the PD design may violate IEEE
802.3af requirements.
If the load capacitor is too large, there can be a problem with inadvertent power shutdown by the PSE caused by
failure to meet the MPS. This is caused by having a long input current dropout due to a drop in input voltage with
a large capacitance-to-load ratio. The standard gives Equation 2:
I
180
(PD)
C v
10 mA
(2)
where C is the bulk capacitance in µF and I(PD) is the PD load current in mA.
A particular design may have a tendency to cause ringing at the RTN pin during startup, inadvertent hot-plugs of
the PoE input, or plugging in a wall adapter. It is recommended that a minimum value of 1 µF be used at the
output of the TPS2375 if downstream filtering prevents placing the larger bulk capacitor right on the output. When
using ORing option 2, it is recommended that a large capacitor such as a 22 µF be placed across the TPS2375
output.
Transient Suppressor
Voltage transients on the TPS2375 can be caused by connecting or disconnecting the PD, or by other
environmental conditions like ESD. The TPS2375 is specified to operate with absolute maximum voltages
V(VDD-VSS) and V(RTN-VSS) of 100 V. A transient voltage suppressor, such as the SMAJ58A, should be installed
after the bridge and across the TPS2375 input as shown in Figure 1. Various configurations of output filters and
the insertion of local power sources across either the TPS2375 input or output have the potential to cause
stresses outside the absolute maximum ratings of the device. Designers should be aware of this possibility and
account for it in their circuit designs. For example, use adequate capacitance across the output to limit the
magnitude of voltage ringing caused by downstream filters. Plugging an external power source across the output
may cause ESD-like events. Some form of protection should be considered based on a study of the specific
waveforms seen in an application circuit.
Layout
The layout of the PoE front end must use good practices for power and EMI/ESD. A basic set of
recommendations include:
1. The parts placement must be driven by the power flow in a point-to-point manner such as RJ-45 → Ethernet
transformer → diode bridges → TVS and 0.1-µF capacitor → TPS2375 → output capacitor.
2. There should not be any crossovers of signals from one part of the flow to another.
3. All leads should be as short as possible with wide power traces and paired signal and return.
4. Spacing consistent with safety standards like IEC60950 must be observed between the 48-V input voltage
rails and between the input and an isolated converter output.
5. The TPS2375 should be over a local ground plane or fill area referenced to VSS to aid high-speed operation.
6. Large SMT component pads should be used on power dissipating devices such as the diodes and the
TPS2375.
Use of added copper on local power and ground to help the PCB spread and dissipate the heat is recommended.
Pin 4 of the TPS2375 has the lowest thermal resistance to the die.
16
Submit Documentation Feedback
Copyright © 2004–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS2375 TPS2376 TPS2377
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS2375D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2375PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2375
TPS2376D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2376PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2376
TPS2377D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPS2377DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377PWR
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
TPS2377PWRG4
ACTIVE
TSSOP
PW
8
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2377
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jun-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS2375DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TPS2375PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
TPS2376DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TPS2376PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
TPS2377DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TPS2377PWR
TSSOP
PW
8
2000
330.0
12.4
7.0
3.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Jun-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS2375DR
SOIC
D
8
2500
340.5
338.1
20.6
TPS2375PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
TPS2376DR
SOIC
D
8
2500
367.0
367.0
35.0
TPS2376PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
TPS2377DR
SOIC
D
8
2500
367.0
367.0
35.0
TPS2377PWR
TSSOP
PW
8
2000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated