APITECH SF0150BA03095S

150 MHz SAW Filter
5.7 MHz Bandwidth
Part Number SF0150BA03095S
DESCRIPTION
•
•
•
150 MHz SAW bandpass filter with 5.7 MHz bandwidth.
13.3 x 6.5 mm SMP.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal:
Vertical from Top:
Frequency :
Relative Magnitude :
Relative magnitude :
Group Delay Deviation :
S11
2.5
10
1
150
MHz/div
dB/div
dB/div
ns/div
S22
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0150BA03095S Rev A
ECN 36650
11-Mar-2010
Page 1 of 4
150 MHz SAW Filter
5.7 MHz Bandwidth
Part Number SF0150BA03095S
SPECIFICATION
Parameter 1
Center Frequency (FC) 2
Insertion Loss 4
1 dB Bandwidth 3
3 dB Bandwidth 3
40 dB Bandwidth 3
Stopband Rejection (25 to 135 MHz)
Stopband Rejection (165 to 2000 MHz)
Passband Amplitude Variation (Fc+/-2.75 MHz)
Passband Group Delay Variation (Fc+/-2.75 MHz) 5
Absolute Delay
Input and Output Return Loss(Fc+/-2.75 MHz) 5
Source and Load Impedance
Ambient Temperature
Notes:
Min
149.875
5.7
6.1
45
45
-
Typ
150.025
19.3
5.95
6.42
7.95
54
53
0.67
115
1.81
1.3
50
25
Max
150.175
21
8.3
0.8
150
2.0
1.8
-
Units
MHz
dB
MHz
dB
dB
dB
dB
dB p-p
ns p-p
us
:1
Ω
°C
1. All electrical specifications apply over the full operating temperature range and include allowance for
all manufacturing tolerance.
2. Defined as the mean of the 10 dB frequencies.
3. dB levels are taken to be relative to the insertion loss.
4. Measured at the maximum level (lowest insertion loss) of the response.
5. When matched as indicated below.
MAXIMUM RATINGS
Parameter
Storage Temperature Range
Operating Temperature Range
Input Power Level
D.C. Voltage between Each Terminal
Min
Max
Units
-45
85
˚C
-10
50
˚C
20
dBm
15
V
Human Body Model: 1000 V
Machine Model: 200 V
ESD Level
MATCHING CIRCUIT
10
5
Input
50 Ω
Single-ended
Output
50 Ω
Single-ended
All other pads
Typical component values:
(Minimum inductor Q = 40)
Ls1
Cp1
Rp1
=
=
=
39
47
220
nH
pF
Ω
Ls2 =
Cp2 =
Rp2 =
33
50
130
nH
pF
Ω
Notes:
1. Required component tolerances: resistors +/-5%, inductors +/-2%, capacitors +/-5%
2. Component values shown are for guidance only and may change depending on board layout.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0150BA03095S Rev A
ECN 36650
11-Mar-2010
Page 2 of 4
150 MHz SAW Filter
5.7 MHz Bandwidth
Part Number SF0150BA03095S
PACKAGE OUTLINE
13.30
SUGGESTED FOOTPRINT
+.20
-.10
+.20
-.10
6.50
Units: mm
Tolerances are ±0.15 mm except
for the overall length and width,
which are nominal values.
Pad Configuration:
Input:
10
Output:
5
Ground:
1,2,3,4,6,7,8,9
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm min,
over a 1.3-8.9 µm Ni plating
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0150BA03095S Rev A
ECN 36650
11-Mar-2010
Page 3 of 4
150 MHz SAW Filter
5.7 MHz Bandwidth
Part Number SF0150BA03095S
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Parameter
Life Testing
Temperature Cycling
Vibration
Mechanical Shock
Solder Heat Resistance and Reflow
Condition
Lead Integrity
Solderability
Hermeticity
ESD Classification
Precautions
Qualification Conditions
High temperature bake at +85 ºC for 168 hours.
MIL-STD 883, Method 1010:
-40 ºC to +85 ºC, 10 cycles, 10 minutes dwell at
temperature extremes
MIL-STD-202, Method 201A:
10 to 55 Hz, double amplitude of 0.06” for 2 hours in each
axis.
MIL-STD-883, Method 2002, Test Condition B:
1500 g, 3 impacts each axis
Peak temperature 240+/-5 ºC for 10 seconds.
Pre-heat: 150-170 ºC for 60 to 90 seconds.
Peak dwell: over 200 ºC for 23 to 26 seconds.
Handling: Class 1 per MIL-STD-1686
Reflow Profile is shown at the bottom of this table.
MIL-STD 883 Method 2004, Condition D
8 oz for 30 seconds.
MIL-STD-883 Method 2003:
245 ºC +/-5 ºC; 95% coverage; no steam aging
MIL-STD 883 Method 1014:
Condition A2 and Condition C (no bomb)
Class I per MIL-STD-883 Method 3015;
Ensure ESD shielding bag is used during transportation
processes;
Personal grounding must be worn at all times when
handling the device.
Do not subject devices to ultrasonic cleaning, which may
cause deterioration and destruction of the device.
Reflow Profile
250
TEMP (deg C)
200
150
100
50
0
0
50
100
150
200
250
300
TIME (sec)
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0150BA03095S Rev A
ECN 36650
11-Mar-2010
Page 4 of 4