426 MHz SAW Filter 9.2 MHz Bandwidth Part Number: SF0426BA03153S DESCRIPTION • • • 426 MHz SAW bandpass filter with 9.2 MHz bandwidth. 13.3 x 6.5 mm LCC package. RoHS compliant. TYPICAL PERFORMANCE Horizontal: 5 MHz/div Vertical (from top): Magnitude : Magnitude : Phase Linearity : Group Delay : 10 1 5 50 dB/div dB/div deg/div ns/div Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0426BA03153S Rev A 25-Mar-2010 ECN 36650 Page 1 of 3 426 MHz SAW Filter 9.2 MHz Bandwidth Part Number: SF0426BA03153S SPECIFICATION Parameter Center Frequency FC 1 Insertion Loss 2 Unit-to-unit Insertion Loss Variation (at room temperature 25°C) Variation of Insertion Loss over operating temperature range Lower 1 dB Bandedge Upper 1 dB Bandedge Lower 3 dB Bandedge Upper 3 dB Bandedge Lower 40 dB Bandedge Upper 40 dB Bandedge Amplitude Variation, 421.4 – 430.6 MHz Phase Linearity, 421.4 – 430.6 MHz Group Delay Variation, 421.4 – 430.6 MHz Maximum Group Delay Change Rate, 421.4 – 430.6 MHz Absolute Delay Triple Transit Suppression Rejection, 100 - 411 MHz 3 Rejection, 441 - 500 MHz 3 Source/Load Impedance Notes: Min - Typ 426 21.3 Max 22 Units MHz dB ±0.5 dB ±0.8 dB MHz MHz MHz MHz MHz MHz dB p-p deg p-p ns p-p 430.6 431.0 418.8 - 421.0 431.0 420.7 431.3 419.1 432.7 0.6 2.2 33 421.4 421.0 433.2 1.0 6 100 - 2.1 - ns/10kHz 40 50 50 0.985 43.5 58 55 50 - µs dBc dB dB ohms 1. Average of the lower and upper 3 dB band edge frequencies 2. Mean level over 421.4 – 430.6 MHz at room temperature 25°C 3. All rejection levels are in dB relative to the insertion loss MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -45 10 - 85 70 10 Units ˚C ˚C dBm Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0426BA03153S Rev A 25-Mar-2010 ECN 36650 Page 2 of 3 426 MHz SAW Filter 9.2 MHz Bandwidth Part Number: SF0426BA03153S MATCHING CIRCUIT 11 5 Output 50 Ω Single-ended Input 50 Ω Single-ended 12 6 GND GND Typical component values: Ls1 = 39 nH Cp1 = 15 pF Ls2 = 33 nH Cp2 = 22 pF Notes: 1. 2% tolerance matching components are recommended. 2. Tuning values shown are for reference only. Optimum values may change depending upon board layout. PACKAGE OUTLINE Units: mm Tolerances are ±0.15 mm except for the overall length and width, which are nominal values. Pad Configuration: Input: 11 Input Return: 12 Output: 5 Output Return: 6 Ground: 1,2,3,4,7,8,9,10 Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0426BA03153S Rev A 25-Mar-2010 ECN 36650 Page 3 of 3