ISL6506BIBZ ® Data Sheet June 8, 2011 Multiple Linear Power Controller with ACPI Control Interface FN7814.0 Features The ISL6506BIBZ complements other power building blocks (voltage regulators) in ACPI-compliant designs for microprocessor and computer applications. The IC integrates the control of the 5VDUAL and 3.3VDUAL rails into an 8 Ld EPAD SOIC package. The ISL6506BIBZ operating mode (active outputs or sleep outputs) is selectable through two digital control pins; S3 and S5. A completely integrated linear regulator generates the 3.3VDUAL voltage plane from the ATX supply’s 5VSB output during sleep states (S3, S4/S5). In active states (during S0 and S1/S2), the ISL6506BIBZ uses an external N-Channel pass MOSFET to connect the outputs directly to the 3.3V input supplied by an ATX power supply, for minimal losses. The ISL6506BIBZ powers up the 5VDUAL plane by switching in the ATX 5V output through an NMOS transistor in active states, or by switching in the ATX 5VSB through a PMOS (or PNP) transistor in S3 sleep state. In S4/S5 sleep states, the ISL6506BIBZ 5VDUAL output is shut down. • Provides 2 ACPI-Controlled Voltages - 5VDUAL USB/Keyboard/Mouse - 3.3VDUAL/3.3VSB PCI/Auxiliary/LAN • Excellent 3.3VDUAL Regulation in S3/S4/S5 - ±2.0% Over-Temperature - 2A Capability • Small Size; Very Low External Component Count • Over-Temperature Shutdown • Pb-Free Available (RoHS Compliant) Applications • ACPI-Compliant Power Regulation for Motherboards - 5VDUAL is shut down in S4/S5 sleep states Pinout ISL6506BIBZ (8 LD EPSOIC) TOP VIEW The ISL6506BIBZ features a 2A current limit on the internal 3.3V LDO. VCC 1 3V3AUX 2 8 N/C 7 5VDLSB GND S3 3 6 DLA S5 4 5 GND Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING ISL6506BIBZ 6506B IBZ TEMP. RANGE (°C) -40 to +85 PACKAGE (Pb-free) 8 Ld EPSOIC PKG. DWG. # M8.15C NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6506BIBZ. For more information on MSL please see techbrief TB363. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL6506BIBZ Block Diagram DLA S3 VCC 12V POR SENSE 3.5Ω S5 10µA 10µA MONITOR AND CONTROL 5VDLSB TEMPERATURE MONITOR SOFT-START 7.5µA VCC DIGITAL ( SOFT-START ) + - UV DETECTOR EA1 3V3AUX GND Typical Application 12VATX 5VSBY 3V3ATX 5VSBY 5VATX 1kΩ Cg (OPTIONAL) ISL6506BIBZ 2 SLP_S3 SLP_S5 3 4 VCC NC 3V3AUX 5VDLSB S3 EPAD 1 S5 9 2 DLA GND 8 5VDUAL 7 Q2 6 Q3 5 Q1 3V3DUAL FN7814.0 June 8, 2011 ISL6506BIBZ Absolute Maximum Ratings Thermal Information Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V DLA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +14.5V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4000V Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) EPSOIC Package (Notes 4, 5) . . . . . . 40 3.5 Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5% Lowest 5VSB Supply Voltage Guaranteeing Parameters . . . . +4.5V Digital Inputs, VSx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +5.5V Ambient Temperature Range . . . . . . . . . . . . . . . . . . .-40°C to +85°C Junction Temperature Range. . . . . . . . . . . . . . . . . . . 0°C to +125°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. 5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Recommended Operating Conditions. Boldface limits apply over the operating temperature range, -40°C to +85°C. PARAMETER SYMBOL TEST CONDITIONS MIN MAX (Note 6) TYP (Note 6) UNITS VCC SUPPLY CURRENT Nominal Supply Current I5VSB VS3 = 5V, VS5 = 5V (S0 State) - 3.60 - mA VS3 = 0V, VS5 = 5V (S3 State) - 4.60 - mA VS5 = 0V (S5 State) - 4.60 - mA Rising 5VSB POR Threshold - - 4.5 V Falling 5VSB POR Threshold 3.60 - 3.95 V 8.9 9.8 11 V POWER-ON RESET Rising 12V POR Threshold 1.00kΩ resistor between DLA and 12V Rail 3.3VAUX LINEAR REGULATOR - - 2.0 % V3V3SB V5VSBY = 5.0V, I3V3SB = 0A - 3.3 - V 3V3SB Undervoltage Threshold V3V3SB_UV - 2.5 - V 3V3SB Overcurrent Trip I3V3SB_TRIP - - 2 A 20 - 35 mA - 58 - µs 6.55 8.2 9.85 ms - -7.5 - µA High Level Input Threshold - - 2.2 V Low Level Input Threshold 0.8 - - V - 10 - µA - 140 - °C Regulation 3V3SB Nominal Voltage Level 5VDUAL SWITCH CONTROLLER 5VDLSB Output Drive Current I5VDLSB V5VDLSB = 4V, V5VSB = 5V TIMING INTERVAL S0 to S3 Transition Delay SOFT-START Soft-start Interval tSS 5VDLSB Soft-start Current Source CONTROL I/O (S3, S5) S3, S5 Internal Pull-down Current to GND TEMPERATURE MONITOR Shutdown-Level Threshold NOTE: 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 3 FN7814.0 June 8, 2011 ISL6506BIBZ Functional Pin Description VCC (Pin 1) Provide a very well decoupled 5V bias supply for the IC to this pin by connecting it to the ATX 5VSB output. This pin provides all the bias for the IC as well as the input voltage for the internal standby 3V3AUX LDO. The voltage at this pin is monitored for power-on reset (POR) purposes. Initialization The ISL6506BIBZ automatically initializes upon receipt of input power. The Power-On Reset (POR) function continually monitors the 5VSB input supply voltage. The ISL6506BIBZ also monitors the 12V rail to insure that the ATX rails are up before entering into the S0 state even if both SLP_S3 and SLP_S5 are both high. Dual Outputs Operational Truth Table GND (Pin 5, Pad) Signal ground for the IC. These pins are also the ground return for the internal 3V3AUX LDO that is active in S3/S4/S5 sleep states. All voltage levels are measured with respect to these pins. S3 and S5 (Pins 3 and 4) These pins switch the IC’s operating state from active (S0, S1/S2) to S3 and S4/S5 sleep states. These are digital inputs featuring internal 10µA pull-down current sources on each pin. Additional circuitry blocks illegal state transitions, such as S4/S5 to S3. Connect S3 and S5 to the computer system’s SLP_S3 and SLP_S5 signals, respectively. 3V3AUX (Pin 2) Table 1 describes the truth combinations pertaining to the 3.3VDUAL and 5VDUAL outputs. The internal circuitry does not allow the transition from an S4/S5 state to an S3 state. TABLE 1. 5VDUAL OUTPUT TRUTH TABLE S5 S3 3.3AUX 5VDL COMMENTS 1 1 3.3V 5V S0/S1/S2 States (Active) 1 0 3.3V 5V S3 0 1 0 0 Note 3.3V Maintains Previous State 0V S4/S5 NOTE: Combination Not Allowed. Connect this pin to the 3V3DUAL output. In sleep states, the voltage at this pin is regulated to 3.3V through an internal pass device powered from 5VSBY through the VCC pin. In active states, ATX 3.3V output is delivered to this node through a fully-on NMOS transistor. During S3 and S4/S5 states, this pin is monitored for undervoltage events. DLA (Pin 6) This pin is an open-drain output. A 1kΩ resistor must be connected from this pin to the ATX 12V output. This resistor is used to pull the gates of suitable N-MOSFETs to 12V, which in active state, switch in the ATX 3.3V and 5V outputs into the 3.3VAUX and 5VDUAL outputs, respectively. This pin is also used to monitor the 12V rail during POR. If a resistor other than 1kΩ is used, the POR level will be affected. Functional Timing Diagram Figure 1 is a simplified timing diagram, detailing the powerup/down sequences of all the outputs in response to the status of the sleep-state pins (S3, S5), as well as the status of the input ATX supply. Not shown in this diagram is the deglitching feature used to protect against false sleep state tripping. Additionally, the ISL6506BIBZ features a 60µs delay in transitioning from S0 to S3 states. The transition from the S0 state to S4/S5 state is immediate. 5VSB S3 S5 5VDLSB (Pin 7) Connect this pin to the gate of a suitable P-MOSFET. In S3 sleep state, this transistor is switched on, connecting the ATX 5VSB output to the 5VDUAL regulator output. Description 3.3V, 5V, 12V DLA 3V3AUX 5VDLSB Operation 5VDL The ISL6506BIBZ controls 2 output voltages, 3.3VDUAL and 5VDUAL. It is designed for microprocessor computer applications requiring 3.3V, 5V, 5VSB, and 12V bias input from an ATX power supply. The IC is composed of one linear controller/regulator supplying the computer system’s 3.3VDUAL power, a dual switch controller supplying the 5VDUAL voltage, as well as all the control and monitoring functions necessary for complete ACPI implementation. 4 FIGURE 1. 5VDUAL AND 3.3VAUX TIMING DIAGRAM; ISL6506BIBZ Soft-Start Figures 2 and 3 show the soft-start sequence for the typical application start-up into a sleep state. At time t0, 5VSB (bias) is applied to the circuit. At time t1, the 5VSB surpasses POR level. Time t2, one soft-start interval after t1, denotes the FN7814.0 June 8, 2011 ISL6506BIBZ initiation of soft-start. The 3.3VDUAL rail is brought up through the internal standby LDO through an internal digital soft-start function. Figure 3 shows the 5VDUAL rail initiating a soft-start at time t2 as well. At time t4, the system has transitioned into S0 state and the ATX supplies have begun to ramp-up. With the ISL6506BIBZ (Figure 2), the 5VDUAL rail will begin to ramp-up from the 5VATX rail through the body diode of the N-MOSFET (Q3). At time t5, the 12VATX rail has surpassed the 12V POR level. Time t6 is three soft-start cycles after the 12V POR level has been surpassed. At time t6, three events occur simultaneously. The DLA pin is forced to a high impedance state which allows the 12V rail to enhance the two NMOSFETs (Q1 and Q3) that connect the ATX rails to the 3.3VDUAL and 5VDUAL rails. The 5VDLSB pin is actively pulled high, which will turn the P-MOSFET (Q2) off. Finally, the internal LDO which regulates the 3.3VAUX rail in sleep states is put in standby mode. 12VATX (2V/DIV) 5VATX (1V/DIV) 3.3VATX (1V/DIV) 5VSB (1V/DIV) 5VDUAL (1V/DIV) 5VSB (1V/DIV) 3.3VDUAL (2V/DIV) 12VATX (2V/DIV) 5VATX (1V/DIV) 3.3VATX (1V/DIV) 0V 5VDLSB (5V/DIV) t0 t1 t2 DLA (10V/DIV) t3 t4 t5 TIME t6 FIGURE 3. SOFT-START INTERVAL FOR S3 TO S0 TRANSITION FOR ISL6506BIBZ Internal Linear Regulator Undervoltage Protection 3.3VDUAL (2V/DIV) 5VDUAL (1V/DIV) 0V DLA (10V/DIV) The undervoltage protection on the internal linear regulator is only active during sleep states and after the initial soft-start ramp of the 3.3V linear regulator. The undervoltage trip point is set at 25% below nominal, or 2.475V. When an undervoltage is detected, the 3.3V linear regulator is disabled. One soft-start interval later, the 3.3V linear regulator is retried with a soft-start ramp. If the linear regulator is retried 3 times and a fourth undervoltage is detected, then the 3.3V linear regulator is disabled and can only be reset through a POR reset. Internal Linear Regulator Overcurrent Protection t0 t1 t2 t3 t4 t5 TIME t6 FIGURE 2. ISL6506BIBZ SOFT-START INTERVAL IN S4/S5 STATE AND S5 TO S0 TRANSITION Sleep to Wake State Transitions Figures 2 and 3, starting at time t4, depict the transitions from sleep states to the S0 wake state. Figure 2 shows the transition of the ISL6506BIBZ from the S4/S5 state to the S0 state. Figure 3 shows how the ISL6506BIBZ will transition from the S3 sleep state into S0 state. For all transitions, t4 depicts the system transition into the S0 state. Here, the ATX supplies are enabled and begin to ramp up. At time t5, the 12VATX rail has exceeded the POR threshold. Three softstart periods after time t5, at time t6, three events occur simultaneously. The DLA pin is forced to a high impedance state, which allows the 12V rail to enhance the two NMOSFETs (Q1 and Q3) that connect the ATX rails to the 3.3VDUAL and 5VDUAL rails. The 5VDLSB pin is actively pulled high, which will turn the P-MOSFET (Q2) off. Finally, the internal LDO which regulates the 3.3VDUAL rail in sleep states is put in standby mode. 5 When an overcurrent condition is detected, the gate voltage to the internal NMOS pass element is reduced, which causes the output voltage of the linear regulator to be reduced. When the output voltage is reduced to the undervoltage trip point, the undervoltage protection is initiated and the output will shutdown. Layout Considerations The typical application employing an ISL6506BIBZ is a fairly straight forward implementation. Like with any other linear regulator, attention has to be paid to the few potentially sensitive small signal components, such as those connected to sensitive nodes or those supplying critical bypass current. The power components (pass transistors) and the controller IC should be placed first. The controller should be placed in a central position on the motherboard, not excessively far from the 3.3VDUAL island or the I/O circuitry. Ensure the 3V3AUX connection is properly sized to carry 1A without exhibiting significant resistive losses at the load end. Similarly, the input bias supply (5VSB) carries a similar level of current (for best results, ensure it is connected to its respective source through an adequately sized trace and is FN7814.0 June 8, 2011 ISL6506BIBZ properly decoupled). The pass transistors should be placed on pads capable of heatsinking matching the device’s power dissipation. Where applicable, multiple via connections to a large internal plane can significantly lower localized device temperature rise. support both the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers to create power islands connecting the filtering components (output capacitors) and the loads. Use the remaining printed circuit layers for small signal wiring. Placement of the decoupling and bulk capacitors should reflect their purpose. As such, the high-frequency decoupling capacitors should be placed as close as possible to the load they are decoupling; the ones decoupling the controller close to the controller pins, the ones decoupling the load close to the load connector or the load itself (if embedded). Even though bulk capacitance (aluminum electrolytics or tantalum capacitors) placement is not as critical as the high-frequency capacitor placement, having these capacitors close to the load they serve is preferable. Component Selection Guidelines Locate all small signal components close to the respective pins of the control IC, and connect them to ground, if applicable, through a via placed close to the ground pad. 12VATX 5VSB CIN 5VDLSB C5VSB 5VDUAL +3.3VIN Also, during the transition between active and sleep states on the 5VDUAL output, there is a short interval of time during which none of the power pass elements are conducting. During this time the output capacitors have to supply all the output current. The output voltage drop during this brief period of time can be easily approximated using Equation 1: (EQ. 1) C5V CHF5V LOAD where: ISL6506BIBZ ΔVOUT = output voltage drop ESROUT = output capacitor bank ESR Q2 DLA Q4 IOUT = output current during transition 3V3DUAL 3V3AUX LOAD The output capacitors should be selected to allow the output voltage to meet the dynamic regulation requirements of active state operation (S0/S1). The load transient for the various microprocessor system’s components may require high quality capacitors to supply the high slew rate (di/dt) current demands. Thus, it is recommended that the output capacitors be selected for transient load regulation, paying attention to their parasitic components (ESR, ESL). tt ⎞ ⎛ ΔV OUT = I OUT × ⎜ ESR OUT + ----------------⎟ C ⎝ OUT⎠ Q3 VCC Output Capacitors Selection CHF3V 5VATX C3V GND EPAD KEY ISLAND ON POWER PLANE LAYER ISLAND ON CIRCUIT/POWER PLANE LAYER VIA CONNECTION TO GROUND PLANE FIGURE 4. PRINTED CIRCUIT BOARD ISLANDS A multi-layer printed circuit board is recommended. Figure 4 shows the connections to most of the components in the circuit. Note that the individual capacitors shown each could represent numerous physical capacitors. Dedicate one solid layer for a ground plane and make all critical component ground connections through vias placed as close to the component terminal as possible. The EPAD should be tied to the ground plane with three to five vias for good thermal management. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Ideally, the power plane should 6 COUT = output capacitor bank capacitance tt = active-to-sleep/sleep-to-active transition time (10µs typical) The output voltage drop is heavily dependent on the ESR (equivalent series resistance) of the output capacitor bank, the choice of capacitors should be such as to maintain the output voltage above the lowest allowable regulation level. Input Capacitors Selection The input capacitors for an ISL6506BIBZ application must have a sufficiently low ESR so as not to allow the input voltage to dip excessively when energy is transferred to the output capacitors. If the ATX supply does not meet the specifications, certain imbalances between the ATX’s outputs and the ISL6506BIBZ’s regulation levels could have as a result a brisk transfer of energy from the input capacitors to the supplied outputs. At the transition between active and sleep states, such phenomena could be responsible for the 5VSB voltage drooping excessively and affecting the output regulation. The solution to such a potential problem is using larger input capacitors with a lower total combined ESR. FN7814.0 June 8, 2011 ISL6506BIBZ Transistor Selection/Considerations The ISL6506BIBZ usually requires one P-Channel and two N-Channel MOSFETs. All three of these MOSFETs are utilized as ON/OFF switching elements. One important criteria for selection of transistors for all the switching elements is package selection for efficient removal of heat. The power dissipated in a switch element while on is shown in Equation 2: 2 P LOSS = I o × r DS ( ON ) (EQ. 2) Select a package and heatsink that maintains the junction temperature below the rating with the maximum expected ambient temperature. Q1, Q3 These N-Channel MOSFETs are used to switch the 3.3V and 5V inputs provided by the ATX supply into the 3.3VAUX and 5VDUAL outputs while in active (S0, S1) state. The main criteria for the selection of these transistors is output voltage budgeting. The maximum rDS(ON) allowed at highest junction temperature can be expressed using Equation 3: V INmin – V OUTmin r DS ( ON )max = --------------------------------------------------I OUTmax (EQ. 3) where: VINmin = minimum input voltage VOUTmin = minimum output voltage allowed IOUTmax = maximum output current Q2 This is a P-Channel MOSFET used to switch the 5VSB output of the ATX supply into the 5VDUAL output during sleep states. The selection criteria of this device, as with the N-Channel MOSFETs, is proper voltage budgeting. The maximum rDS(ON) , however, has to be achieved with only 4.5V of gate-to-source voltage, so a true logic level MOSFET needs to be selected. 7 FN7814.0 June 8, 2011 ISL6506BIBZ Small Outline Exposed Pad Plastic Packages (EPSOIC) M8.15C N INDEX AREA H 0.25(0.010) M 8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD PLASTIC PACKAGE B M E INCHES -B- 1 2 SYMBOL 3 TOP VIEW L SEATING PLANE -A- A D -C- e α A1 B C 0.10(0.004) 0.25(0.010) M C A M B S SIDE VIEW MILLIMETERS MAX MIN MAX NOTES A 0.056 0.066 1.43 1.68 - A1 0.001 0.005 0.03 0.13 - B 0.0138 0.0192 0.35 0.49 9 C 0.0075 0.0098 0.19 0.25 - D 0.189 0.196 4.80 4.98 3 E 0.150 0.157 3.811 3.99 4 e h x 45° MIN 0.050 BSC 1.27 BSC - H 0.230 0.244 5.84 6.20 - h 0.010 0.016 0.25 0.41 5 L 0.016 0.035 0.41 0.89 6 8° 0° N α 8 0° 8 7 8° - P - 0.126 - 3.200 11 P1 - 0.099 - 2.514 11 Rev. 1 6/05 NOTES: 1 2 3 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. P1 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. N P BOTTOM VIEW 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 11. Dimensions “P” and “P1” are thermal and/or electrical enhanced variations. Values shown are maximum size of exposed pad within lead count and body size. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 8 FN7814.0 June 8, 2011