1505 data 3 delay devices, inc. 5-TAP SIP DELAY LINE TD/TR = 3 (SERIES 1505) FEATURES • • • • • • PACKAGES 5 taps of equal delay increment Very narrow device (SIP package) Stackable for PC board economy Low profile Epoxy encapsulated Meets or exceeds MIL-D-23859C 1505-xxz xx = Delay (TD) z = Impedance Code 1 2 3 4 5 6 7 GND IN T1 T2 T3 T4 T5 PIN DESCRIPTIONS FUNCTIONAL DESCRIPTION The 1505-series device is a fixed, single-input, five-output, passive delay IN Signal Input line. The signal input (IN) is reproduced at the outputs (T1-T5) in equal T1-T5 Tap Outputs increments. The delay from IN to T5 (TD) is given by the device dash GND Ground number. The characteristic impedance of the line is given by the letter code that follows the dash number (See Table). The rise time (TR) of the line is 33% of TD, and the 3dB bandwidth is given by 1.05 / TD. SERIES SPECIFICATIONS • • • • • Dielectric breakdown: Distortion @ output: Operating temperature: Storage temperature: Temperature coefficient: DASH NUMBER SPECIFICATIONS 50 Vdc 10% max. -55°C to +125°C -55°C to +125°C 100 PPM/°C T1 T2 T3 T4 IN T5 GND Functional Diagram 1 2 3 4 5 6 7 .200 MAX. .800 MAX. .020 TYP. .020 TYP. .600 TYP. .100 TYP. .250 MAX. Part Number 1505-5A 1505-10A 1505-20A 1505-30A 1505-40A 1505-50A 1505-60A 1505-70A 1505-80A 1505-90A 1505-100A 1505-5B 1505-10B 1505-20B 1505-30B 1505-40B 1505-50B 1505-60B 1505-75B 1505-100B 1505-30C 1505-50C 1505-60C 1505-100C 1505-50G 1505-100G 1505-200G 1505-300G TD (ns) 5.0 ± 1.0 10.0 ± 1.0 20.0 ± 1.5 30.0 ± 2.0 40.0 ± 2.5 50.0 ± 3.0 60.0 ± 3.0 70.0 ± 3.5 80.0 ± 4.0 90.0 ± 5.0 100 ± 5.0 5.0 ± 1.0 10.0 ± 1.0 20.0 ± 1.5 30.0 ± 2.0 40.0 ± 2.5 50.0 ± 3.0 60.0 ± 3.0 75.0 ± 3.5 100 ± 5.0 30.0 ± 2.0 50.0 ± 3.0 60.0 ± 3.0 100 ± 5.0 50.0 ± 3.0 100 ± 5.0 200 ± 10.0 300 ± 15.0 Delay per Tap (ns) 1.0 ± 0.3 2.0 ± 0.4 4.0 ± 0.6 6.0 ± 1.0 8.0 ± 1.5 10.0 ± 1.8 12.0 ± 2.0 14.0 ± 2.0 16.0 ± 2.0 18.0 ± 3.0 20.0 ± 3.0 1.0 ± 0.3 2.0 ± 0.4 4.0 ± 0.6 6.0 ± 1.0 8.0 ± 1.5 10.0 ± 1.8 12.0 ± 2.0 15.0 ± 2.0 20.0 ± 3.0 6.0 ± 1.0 10.0 ± 1.8 12.0 ± 2.0 20.0 ± 3.0 10.0 ± 1.8 20.0 ± 3.0 40.0 ± 6.0 60.0 ± 8.0 TR (ns) 2.0 3.0 6.0 9.0 12.0 15.0 18.0 21.0 24.0 27.0 30.0 2.0 3.0 6.0 9.0 12.0 15.0 18.0 24.0 30.0 9.0 15.0 18.0 30.0 15.0 30.0 60.0 90.0 Impedance (Ω Ω) 50 50 50 50 50 50 50 50 50 50 50 100 100 100 100 100 100 100 100 100 200 200 200 200 500 500 500 500 RDC (Ω Ω) 0.6 0.6 0.7 0.7 0.9 1.0 1.2 1.4 1.6 1.8 2.0 0.7 0.7 1.0 1.5 1.8 2.0 2.0 2.5 2.5 2.5 3.0 3.5 6.0 5.0 15.0 21.0 29.0 .100 MIN. .010 TYP. Package Dimensions 1997 Data Delay Devices Doc #97024 2/6/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 1 1505 PASSIVE DELAY LINE TEST SPECIFICATIONS TEST CONDITIONS INPUT: Ambient Temperature: Input Pulse: OUTPUT: Rload: Cload: Threshold: 25oC ± 3oC High = 3.0V typical Low = 0.0V typical Source Impedance: 50Ω Max. Rise/Fall Time: 3.0 ns Max. (measured at 10% and 90% levels) Pulse Width (TD <= 75ns): PWIN = 100ns Period (TD <= 75ns): PERIN = 1000ns Pulse Width (TD > 75ns): PWIN = 2 x TD Period (TD > 75ns): PERIN = 10 x TD 10MΩ 10pf 50% (Rising & Falling) NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. PERIN PWIN TRISE INPUT SIGNAL TFALL VIH 90% 50% 10% 90% 50% 10% TRISE VIL TFALL TRISE OUTPUT SIGNAL 90% 50% 10% TFALL VOH 90% 50% 10% VOL Timing Diagram For Testing OUT PULSE GENERATOR RIN IN DEVICE UNDER TEST (DUT) TRIG 50 Ω RIN = ROUT = ZLINE IN T1 T2 T3 T4 T5 TRIG OSCILLOSCOPE ROUT Test Setup Doc #97024 2/6/97 DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 2