LXMG221D-0700040-D2F LXMG2203 40W 700mA Dimmable HV LED Driver Module ® TM P RODUCTION D ATASHEET • DESCRIPTION In the case that there is an LED string short between OUTPUT(+) and OUTPUT(-), or string open, or a product over temperature condition the FAULT terminal will go low. The FAULT terminal includes an open collector device that can be pulled up to a maximum of 60V and will sink 8mA typical to 0.8V when a short or open fault occurs. To reduce audible noise the internal switching frequency remains above 30kHz. Safety features include open output circuit protection, whole string short circuit protection. The maximum allowable hot spot case temperature is 90°C (above this temperature the module will be thermally self-protected). The recommended operating ambient temperature range is -30°C to 70°C, as long as the maximum case temperature is not exceeded. The compact enclosure is rated to IP66, meets UL8750 and UL1310 class 2. • High Voltage AC Input: 347VAC to 480VAC • High Efficiency • Active Power Factor Correction • Constant Current 700mA • Dimming Input Provides 10% to 100% Range, Plus Shutdown • Anode Supply Adjusts for String Voltage between 20V and 57V • Small Compact Size • Suitable for Damp Locations (IP66) • UL8750 & UL1310 • UL File E337545 • FCC Class B • Long Life Expectancy • RoHS Compliant • Full Protection: OVP, SCP, OTP, Maximum Power Limit • Unique Fault Detection and Management WWW . Microsemi .C OM The LXMG221D-0700040-D2F is a fully enclosed compact solid-state LED lighting driver module. It operates from a universal AC input supply in the range of 347VAC to 480VAC, 60Hz to drive a string of LEDs with active power factor correction. LED string voltage can range from 20V to 57V at a constant current of 700mA. Control terminal leads include a dimming input BRITE A with a dedicated RETURN lead. The amplitude of the output LED string current will vary from 10% to 100% corresponding to a 1VDC to 10VDC signal on the BRITE A input following the 0V to 10V ESTA E1.3-2001 Analog Control Specification Standard. The BRITE A terminal when pulled down below minimum dimming will turn off the LEDs and enter a low power consumption mode. A second control terminal lead provides a FAULT indicator. KEY FEATURES • APPLICATIONS Residential and Commercial LED Lighting Fixtures such as: • LED Down Lights • LED Street Lights IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com Patents Pending PRODUCT HIGHLIGHT ORDER INFORMATION Part Number Input Voltage Output Current Fault Output LXMG221D-0700040-D2F 347VAC to 480VAC 60Hz 700mA Dimmable Current Source 20V to 57V Anode Voltage Yes Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 1 LXMG221D-0700040-D2F Photo is representative only, actual product may differ slightly LXMG221D-0700040-D2F LXMG2203 40W 700mA Dimmable HV LED Driver Module ® TM P RODUCTION D ATASHEET ABSOLUTE MAXIMUM RATINGS Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. LED Output Current (mA) LED Output Current (mA) Typical Temperature Derating Curve 800 700 600 500 400 VBRITE A = 10V VBRITE A = 1V 300 200 100 WWW . Microsemi .C OM Input Voltage (VIN) ............................................................................................................................................ 0VAC to 528VAC Input Power ......................................................................................................................................... 50W (Internally Limited) Input Frequency (VIN) .......................................................................................................................................... 57Hz to 63Hz Peak Output LED String Current .................................................................................................... 810mA (Internally Limited) Peak Output String Voltage .............................................................................................................. 59.5V (Internally Limited) Output Power ...................................................................................................................................... 44W (Internally Limited) Input Signal Voltage (BRITE A Input) ........................................................................... -0.3V to greater of 10V or OUTPUT(+) Output Signal Voltage (FAULT) ............................................................................................................................ -0.3V to 60V Cold Start Temperature....................................................................................................................................................-30°C Hot Spot Case Temperature, zero airflow ......................................................................................................................... 90°C Storage Temperature Range ..............................................................................................................................-40°C to 85°C Typical Supply Voltage Derating Curve 800 700 600 500 400 VBRITE A = 10V VBRITE A = 1V 300 200 100 0 0 ‐30 ‐15 0 15 30 45 60 75 240 90 280 320 360 400 440 480 520 Input Supply Voltage (VAC) Case Temperature (°C) RECOMMENDED OPERATING CONDITIONS (R.C.) This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond which the inverter, although operational, might not function optimally. Parameter Input Supply Voltage Range Linear BRITE A Control Input Voltage Range LED String Voltage (at 700mA)1 OUTPUT(-) Sink Current Maximum Allowable Case Temperature Cold Start Temperature Min VIN Max Units 347 480 VAC VBRITE A 0 10 V VBRITE_PWM 0.2 10 kHz VBRITE_PWM 10 VOUTPUT(+) V VBRITE_PWM 0.2 25 kHz VLED 40 1) 57 V OUTPUT(-)ISINK 700 TC TCOLD R.C. LXMG221D-0700040-D2F Linear BRITE A Control PWM Frequency Range (Open Collector) Linear BRITE A Control PWM Amplitude Range (Totem Pole) Linear BRITE A Control PWM Frequency Range (Totem Pole) Symbol mA 90 -30 °C °C 1) Operation has been verified down to 20V, but it is recommended that low voltage performance with actual loading be verified by the user. Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 2 LXMG221D-0700040-D2F LXMG2203 ® TM 40W 700mA Dimmable HV LED Driver Module P RODUCTION D ATASHEET ELECTRICAL CHARACTERISTICS Parameter Symbol Input Voltage VIN Off Power PIN(MIN) Input AC Current Maximum Inrush Current I347 I480 Test Conditions / Comment Min Line Frequency 57 to 63 Hz 312 Typ Max Units 528 VAC BRITE A ≤ 0.5V, VIN = 480VAC 0.5 W Measured at Full Load and 347VAC Input 175 mA Measured at Full Load and 480VAC Input 125 mA Measure at 480VAC Peak AC Line; Maximum Duration 10μs 60 A 5 A IINRUSH Measure at 480VAC Peak AC Line Measured after 10μs Power Factor η Efficiency Total Harmonic Distortion Full Load, 347VAC to 480VAC 0.9 Full Load, VLED = 57V, VIN = 480VAC 88 THD Full load, 347VAC to 480VAC IOUT- TA = 25°C 665 20 WWW . Microsemi .C OM Unless otherwise specified, the following specifications apply over the recommended operating condition except where otherwise noted; VIN = 347VAC to 480VAC , 60Hz; BRITE A = 8kΩ to RETURN; FAULT = 1kΩ pull up to 10V Full Load condition uses an LED load with 57VDC @ 700mA unless otherwise noted. Case temperature range: -30°C to 90ºC; production tested at 25ºC. PF 91 % 15 % 735 mA 57 V OUTPUTS Average Sink Current 700 LED String Voltage VOUTΔ Rated LED current Ripple (pk-pk) VOUTΔ Full Load, VLED = 57V, (pk to pk)/Average 2 % Line Regulation IOUT- VIN = Nominal ± 10% (i.e. 480VAC ± 10%) 1 % Load Regulation IOUT- OUTPUT(+) 40V to 57V 1 % 0.5 Sec 10 % Turn-on Time tTURN_ON Output Overshoot / Undershoot IOUT+ Cold Start, Power ON 0.2 Turning Power On or Off Dimming BRITE A Voltage Setting VBRITE A BRITE A Output Current IBRITE A Minimum Output Current IMIN Output Current Dim Range (Analog Dimming) 9.5 10 10.5 For Minimum brightness 0.95 1 1.05 BRITE A to RETURN 1.19 1.25 1.37 BRITE A = 0.95V ILED = 700mA, BRITE A = 0.95V Versus BRITE A ≥ 10V V mA 10 % of Max 10:1 RATIO VBRITE A 0.8 V FAULT Output Voltage Low VFAULT Short OUTPUT(+) to OUT(-), FAULT = 8mA 0.8 V Leakage Current IFAULT No fault, VFAULT = 57V 10 µA 59.5 V Protection Overvoltage Protection VOV Maximum OUT(+) Over Temperature Shutdown TOT Over Case Temperature Protection Hot Spot Copyright © 2011 Rev. 1.1, 2011-12-02 57.5 58.5 90 95 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 °C Page 3 LXMG221D-0700040-D2F Shutdown Voltage For maximum brightness LXMG221D-0700040-D2F LXMG2203 40W 700mA Dimmable HV LED Driver Module ® TM P RODUCTION D ATASHEET Safety & EMC Compliance Compliance to UL8750 & UL1310 Class 2 File E337545 Conducted and Radiated Emission, Class B EN 61000-3-3 Voltage fluctuations and flicker EN61000-4-2 Electrostatic Discharge Immunity EN61000-4-3 Radiated Susceptibility test EN61000-4-4 Electrical Fast Transient EN61000-4-5 and ANSI C61.42.2 Surge Immunity Test, AC Power Line, Category C Low Exposure (6kV/3kV) EN61000-4-6 Conducted Susceptibility Immunity test EN61000-4-8 Power Frequency Magnetic Field Immunity Test EN61000-4-11 Voltage Dips and Interruption Immunity Life Expectancy 5 years / 50,000 hours @ 100% duty at maximum case temperature 55°C 221,569 hours, case temperature 55°; 121,565 hours case temperature 70°C Bellcore TR-NWT-332, Issue 6; Method 1, Case 3, Ground Benign EU RoHS, REACH MTBF Environmental Standards WWW . Microsemi .C OM UL FCC Title 47, Part 15 LEAD DESCRIPTION Name Pin # Description INPUT TERMINAL LEADS (18AWG) BLACK AC LINE WHITE AC NEUTRAL Main Input Power Supply Line 347VAC to 480VAC Main Input Power Supply Neutral CONTROL TERMINAL LEADS (22AWG) PURPLE BRITE A Analog Dimming Input (Full Brightness if Open) GRAY RETURN RETURN BROWN FAULT Fault Signal (Low During Whole LED String Short or Open) OUTPUT TERMINAL LEADS (18AWG) RED OUTPUT(+) LED String Anode Voltage (High Side) BLUE OUTPUT(-) OUTPUT (-) LED Cathode Voltage (Low Side) 700mA OUTPUT(-) FAULT TABLE FAULT DRIVER STATUS ON Hi-Z ON OPEN OPEN LOW LOW OUTPUT(+) Max Voltage SHUTDOWN ON Hi-Z ON Over Temperature at the Case Hot Spot OPEN LOW SHUTDOWN Power Loss (Blackout) Event OPEN LOW SHUTDOWN OPEN Hi-Z SHUTDOWN ON Hi-Z ON BRITE A Shorted TO RETURN or OUTPUT(-) BRITE A OPEN (or Resistor > 12kOhm) Copyright © 2011 Rev. 1.1, 2011-12-02 COMMENT STAYLIT™, OUTPUT(+) ≥ 20V When the temperature goes down, the module turns on again (no user intervention) When Power comes back, the module turns on again (no user intervention) Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 4 LXMG221D-0700040-D2F CONDITION OUTPUT(+) String OUTPUT (-) (700mA) OUTPUT(+) OPEN OUT(-) OUTPUT(+) Short OUT(-) OUTPUT(+) String OUTPUT (-) w/ 1 or more LED short LXMG221D-0700040-D2F LXMG2203 ® TM 40W 700mA Dimmable HV LED Driver Module P RODUCTION D ATASHEET CONDITIONS OF ACCEPTABILITY The components have been judged on the basis of the required spacings in the Standard for Class 2 Power Units, UL 1310. WWW . Microsemi .C OM The input and output leads are 18 AWG, rated 600V, 105ºC, VW-1. The suitability of the leads shall be determined in each enduse application. The leads are suitable for factory wiring only, and additional investigation will be required for field wiring. The polymeric housing is rated V-0 and has been subjected to a ball-impact test. The need for a suitable enclosure shall be considered in the end product. The component has been evaluated for dry and damp locations, where the humidity conditioning and dielectric tests were conducted per UL 8750. The maximum temperature measured on housing outside surface was 61.3°C during the Temperature Test when shifted to Ambient Temperature 40°C. The necessity of repeated Temperature Test shall be determined in each end use application. A proper mechanical, electrical and fire enclosure shall be provided in the end-use application that is in compliance with all the applicable requirements of the end-use application. Testing was on a 20 A branch circuit. If used on a branch circuit greater than this, additional testing may be necessary. The LED driver is rated as noted in the Electrical Ratings Table above, and the outputs comply with the requirements for Class 2. The need for additional evaluation shall be considered in the end product if used beyond these ratings. The LED driver is provided with dimmer leads for connecting an external 0-10 VDC source for dimming the output current. The leads colors are shown in box below. The dimmer circuit is considered as Class 2 circuit. Lead Function Color AC LINE BLACK AC NEUTRAL WHITE OUTPUT(+) RED OUTPUT(-) BLUE RETURN GRAY FAULT BROWN BRITE A PURPLE LXMG221D-0700040-D2F Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 5 LXMG221D-0700040-D2F LXMG2203 40W 700mA Dimmable HV LED Driver Module ® TM P RODUCTION D ATASHEET TYPICAL CHARACTERISTIC CHARTS 25°C 600 50 500 40 400 30 IOUT BRITE A Rising IOUT BRITE A Falling Output Voltage 300 200 100 20 10 0 Output Voltage (V) 60 700 Output Current (mA) WWW . Microsemi .C OM BRITE A INPUT vs OUTPUT CURRENT and OUTPUT VOLTAGE @ VIN = 480VAC 0 0 1 2 3 4 5 6 7 8 9 10 BRITE_A Input (V) Power Factor vs Output Power Power Factor 1 0.9 0.8 PF @ 480VAC 0.7 PF @ 347VAC 0.6 0 5 10 15 20 25 30 35 40 35 40 Output Power (Watts) Efficiency vs Output Power LXMG221D-0700040-D2F Efficiency (%) 100 90 80 Efficiency @ 480VAC Efficiency @ 347VAC 70 60 0 5 10 15 20 25 30 Output Power (Watts) Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 6 LXMG221D-0700040-D2F LXMG2203 TM ® 40W 700mA Dimmable HV LED Driver Module P RODUCTION D ATASHEET MECHANICAL DRAWING WWW . Microsemi .C OM Wire length is 230mm ± 10mm, stripped 12mm ± 5mm UL1015 AWG#18 16/30 stranded 105°C Input & Output wires; AWG#22 7/30 stranded Control wires, all wires tinned. Please insure the wire nuts are installed correctly to prevent intermittent operation. Connecting the AC input to Control or Output wires will result in damage to the module. APPLICATION INFORMATION LXMG221D-0700040-D2F Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 7 LXMG221D-0700040-D2F LXMG2203 TM ® 40W 700mA Dimmable HV LED Driver Module P RODUCTION D ATASHEET NOTES WWW . Microsemi .C OM LXMG221D-0700040-D2F PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2011 Rev. 1.1, 2011-12-02 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: 714-893-2570 Page 8