4-Channel LED Driver with Phase Shift Control and 10-Bit Dimming Resolution ISL97687 Features The ISL97687 is a PWM controlled LED driver that supports 4 channels of LED current, for Monitor and TV LCD backlight applications. It is capable of driving 160mA per channel from a 9V to 32V input supply, with current sources rated up to 75V absolute maximum. • 4x160mA, 75V rated channels with integrated channel regulation FETs • Channels can be ganged for high current - 2x350mA - 1x700mA • 9V~32V input voltage • Dimming modes: - Direct PWM dimming from 100Hz~30kHz - PWM dimming with adjustable output frequency - 10-bit dimming resolution - VSYNC function to synchronize PWM signal to frame rate - Phase shift - Analog to PWM dimming with 8-bit resolution • 2 selectable current levels for 3D applications • Current matching of ±1% • Integrated fault protection features such as string open circuit protection, string short circuit protection, overvoltage protection, and over-temperature protection • 28 Ld 5mmx5mm TQFN and 28 Ld 300mil SOIC Packages Available The ISL97687’s current sources achieve typical current matching to ±1%, while dynamically maintaining the minimum required VOUT necessary for regulation. This adaptive scheme compensates for the non-uniformity of forward voltage variance in the LED strings. The ISL97687 can decode both an incoming PWM signal and an analog input voltage, for DC-to-PWM dimming applications. Modes include direct PWM and several modes where the PWM frequency is synthesized on chip at 10-bit resolution. This can be either free running, or synchronized with the frame rate to give both a frequency and a phase lock, minimizing panel to panel variation and display flicker. Phase shift is supported, reducing flicker and audio noise, as is multiplication of the incoming decoded analog and PWM values. The ISL97687 has an advanced dynamic headroom control function, which monitors the highest LED forward voltage string, and regulates the output to the correct level to minimize power loss. This proprietary regulation scheme also allows for extremely linear PWM dimming from 0.02% to 100%. The LED current can also be switched between two current levels, giving support for 3D applications. The ISL97687 incorporates extensive protections of string open and short circuit detections, OVP, and OTP. VIN: 9V~32V Applications • Monitor/TV LED Backlighting • General/Industrial/Automotive Lighting Related Literature • See AN1674 for “ISL97687IRTZ-HEVALZ and ISL97687IRTZLEVALZ Evaluation Board User Guide” for TQFN Application • See AN1706 for “ISL97687IBZ-EVAL1Z Evaluation Board User Guide” for SOIC Application FUSE D1 160mA MAX PER STRING VIN VLOGIC EN STV EN_VSYNC EN_ADIM PWMI ACTL EN_PS 110 SLEW Q1 GD CS RSENSE PGND COMP OVP CSEL ISET1 ISET2 OSC PWM_SET/PLL CH1 CH2 CH3 CH4 I_CH2 100 CHANNEL CURRENT (mA) VDC I_CH3 90 80 I_CH1 70 I_CH4 60 50 40 30 20 10 0 0 20 40 60 80 100 DIMMING DUTY CYCLE (%) FIGURE 1. ISL97687 APPLICATION DIAGRAM September 27, 2012 FN7714.1 1 FIGURE 2. PWM DIMMING LINEARITY CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011, 2012. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL97687 Block Diagram VIN: 9V~32V 160mA MAX PER STRING FUSE VIN VDC SLEW ANALOG BIAS REG1 REG2 VLOGIC OSC EN OVP IMAX LOGIC FET DRIVERS ILIMIT FAULT/STATUS CONTROL GM AMP OVP OVP FAULT/STATUS REGISTER ∑=0 COMP CS O/P SHORT DIGITAL BIAS FSW OSC & RAMP COMP GD OPEN CKT, SHORT CKT DETECTS CH1 HIGHEST VF STRING DETECT VSET + ISET1 REF GEN + - CH4 1 2 3 TEMP SENSOR ISET2 CSEL REF_OVP REF_VSC GND + - 4 PWMI EN_PS STV SERIAL INTERFACE LED DIMMING CONTROLLER EN_VSYNC ACTL PLL ANALOG INTERFACE OSC EN_ADIM PWM_SET/PLL FIGURE 3. ISL97687 BLOCK DIAGRAM 2 FN7714.1 September 27, 2012 ISL97687 Pin Configurations ISL97687 (28 LD SOIC) TOP VIEW CSEL PGND CH1 CH2 CH3 CH4 PGND ISL97687 (28 LD 5x5 TQFN) TOP VIEW CH2 28 27 26 25 24 23 22 CH1 1 28 CH3 2 27 CH4 PWMI 1 21 ACTL PGND 3 26 PGND STV 2 20 OSC CSEL 4 25 ACTL EN_ADIM 3 19 ISET2 PWMI 5 24 OSC 18 ISET1 STV 6 23 ISET2 EN_ADIM 7 22 ISET1 EN_PS 8 21 COMP VLOGIC 9 20 OVP EN_VSYNC 10 19 PWM_SET/PLL VDC 11 18 PGND VIN 12 17 CS EN 13 16 SLEW AGND 14 15 GD THERMAL* PAD EN_PS 4 VLOGIC 5 17 COMP EN_VSYNC 6 16 OVP VDC 7 15 PWM_SET/PLL 14 13 PGND 12 CS 11 SLEW 10 GD EN VIN 9 AGND 8 *EXPOSED THERMAL PAD Pin Descriptions TQFN SOIC PIN NAME PIN TYPE 1 5 PWMI I PWM Brightness Control Input pin. 2 6 STV I Start Vertical Frame signal; used in VSYNC mode. 3 7 EN_ADIM I Enable Analog Dimming 4 8 EN_PS I Enable Phase Shift 5 9 VLOGIC S Internal 2.5V Digital Bias Regulator. Needs Decoupling Capacitor added to ground. 6 10 EN_VSYNC I Frame synchronization enable. Ties high to VDC for enable VSYNC function. PWM_SET/PLL also needs to be configured with an RC network. Pin can be tied to VDC or VLOGIC to enable function. 7 11 VDC S Internal 5V Analog Bias Regulator. Needs Decoupling Capacitor added to ground. 8 12 VIN S Main Power Input. Range: 9V to 32V. 9 13 EN I LED Driver Enable. Whole chip will shut down when low. 10 14 AGND S Analog Ground 11 15 GD O External Boost FET gate control 12 16 SLEW I Boost Regulation Switching Slew Rate control. 13 17 CS I External Boost FET current sense input. 14 18 PGND S Boost FET gate driver power ground and ground reference for CS pin. 15 19 PWM_SET/ PLL I For direct PWM mode, tie this pin high to VDC. For other non-VSYNC modes, connect to a resistor to set the dimming frequency. If the VSYNC function is enabled, connect this pin to the PLL loop filter network. 16 20 OVP I Overvoltage Protection Input as well as Output Voltage feedback pin. 17 21 COMP I Boost compensation 3 PIN DESCRIPTION FN7714.1 September 27, 2012 ISL97687 Pin Descriptions (Continued) TQFN SOIC PIN NAME PIN TYPE PIN DESCRIPTION 18 22 ISET1 I Resistor connection for setting LED current. 28.7kΩ = 100mA. 19 23 ISET2 I Resistor connection for setting LED current. 28.7kΩ = 100mA. 20 24 OSC I Boost switching frequency adjustment. 21 25 ACTL I Analog dimming input (input range is 0.3V to 3V). 22 26 PGND S Power Ground return for LED current. 23 27 CH4 I LED PWM Driver 24 28 CH3 I LED PWM Driver 25 1 CH2 I LED PWM Driver 26 2 CH1 I LED PWM Driver 27 3 PGND S Power Ground return for LED current. 28 4 CSEL I ISET Resistor Selection Pin. CSEL = 0 : ISET 1 resistor sets LED current CSEL = 1 : ISET 2 resistor sets LED current Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING PACKAGE (Pb-free) PKG. DWG. # ISL97687IRTZ ISL9768 7IRTZ 28 Ld 5x5 TQFN L28.5x5B ISL976787IBZ ISL97687IBZ 28 Ld SOIC (300mil) M28.3 ISL97687IRTZ-LEVALZ Evaluation Board (12 LEDs populated in each channel) ISL97687IRTZ-HEVALZ Evaluation Board (22 LEDs populated in each channel) ISL97687IBZ-EVAL1Z Evaluation Board (None of LEDs on the evaluation board) NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL97687. For more information on MSL, please see Technical Brief TB363. 4 FN7714.1 September 27, 2012 ISL97687 Table of Contents Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Typical Performance Curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PWM Boost Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 OVP and VOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Current Matching and Current Accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Dynamic Headroom Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Dimming Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 LED DC Current Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PWM Dimming Frequency Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Phase Shift Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 VOUT Control when LEDs are Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Switching Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5V and 2.4V Low Dropout Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Soft-Start and Boost Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Fault Protection and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Short Circuit Protection (SCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Open Circuit Protection (OCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Undervoltage Lock-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Over-Temperature Protection (OTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Component Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Input Capacitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Inductor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Output Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Channel Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Schottky Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 High Current Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PCB Layout Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Two Layers PCB Layout with TQFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 General Power PAD Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 One Layer PCB Layout with SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Equivalent Circuit Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5 FN7714.1 September 27, 2012 ISL97687 Absolute Maximum Ratings (TA = +25°C) VIN, EN, PWMI, ACTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 45V VDC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.75V VLOGIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.75V COMP, ISET1, ISET2, PWM_SET, OSC, CS, OVP. . . . . . . . . . . . . . . . . . . . . . .-0.3V to min (VDC+0.3V, 5.75V) EN_VSYNC, CSEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.75V STV, EN_ADIM, EN_PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 5.75V CH1 - CH4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 75V GD, SLEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 18V PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V Above voltage ratings are all with respect to AGND pin ESD Rating Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . . . . 2kV Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 200V Charged Device Model (JESD22-C101E) . . . . . . . . . . . . . . . . . . . . . . . 1kV Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA Thermal Information Thermal Resistance θJA (°C/W) 28 Ld TQFN (4 layer + vias, Notes 4, 5) . . . 32 28 Ld SOIC (4 layer, Notes 6, 7) . . . . . . . . . 54 Thermal Characterization (Typical, Note 8) θJC (°C/W) 4 25 PSIJT (°C/W) 28 Ld TQFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 28 Ld SOIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maximum Continuous Junction Temperature . . . . . . . . . . . . . . . . .+125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Power Dissipation TQFN (W) SOIC (W) TA < +25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13 1.85 TA < +70°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.72 1.02 TA < +85°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25 0.74 TA < +105°C . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.63 0.37 Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. 6. For θJC, the “case temp” location is taken at the package top center. 7. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 8. PSIJT is the PSI junction-to-top thermal characterization parameter. If the package top temperature can be measured with this rating then the die junction temperature can be estimated more accurately than the θJC and θJC thermal resistance ratings. Electrical Specifications All specifications below are characterized at TA = -40°C to +105°C; VIN = 12V, EN = 5V. Boldface limits apply over the operating temperature range, -40°C to +105°C. PARAMETER DESCRIPTION CONDITION MIN (Note 9) TYP MAX (Note 9) UNIT GENERAL VIN Backlight Supply Voltage (Note 10) IVIN_STBY VIN Shutdown Current EN = 0 IVIN_ACTIVE Switching RFPWM = 3.3kΩ, ILED = 100mA, fSW = 600kHz, COUT_SW = 1nF VUVLO Undervoltage Lock-out Threshold VUVLO_HYS Undervoltage Lock-out Hysteresis 9 10 Non-switching 4 2.9 32 V 5 µA 13 mA 5.5 mA 3.3 V 300 mV LINEAR REGULATOR VDC 5V Analog Bias Regulator VIN > 6V VDC_DROP VDC LDO Load Regulation Tolerance IVDC = 30mA VLOGIC 2.5V Logic Bias Regulator VIN > 6V VLOGIC_DROP VLOGIC LDO Load Regulation Tolerance IVLOGIC = 30mA 4.8 2.3 5 5.1 V 71 100 mV 2.4 2.5 V 31 100 mV BOOST SWITCH CONTROLLER tSS Soft-Start 16 ms ISW_LIMIT Boost FET Current Limit (See Equation 5) RSENSE = 50mΩ tR Gate Rise Time COUT_SW = 1000pF 20 ns tF Gate Falling Time COUT_SW = 1000pF 17.6 ns VGD Gate Driver Output Voltage COUT_SW = 1000pF 10 V 6 3.1 3.4 3.8 A FN7714.1 September 27, 2012 ISL97687 Electrical Specifications All specifications below are characterized at TA = -40°C to +105°C; VIN = 12V, EN = 5V. Boldface limits apply over the operating temperature range, -40°C to +105°C. (Continued) PARAMETER DESCRIPTION CONDITION MIN (Note 9) DMAX Boost Maximum Duty Cycle fSW = 600kHz DMIN Boost Minimum Duty Cycle fSW = 1.2MHz fSW Boost Switching Frequency (See Equation 4) ROSC = 250kΩ 180 ROSC = 83kΩ 540 ROSC = 42kΩ 1.08 EFFPEAK TYP MAX (Note 9) 92 Boost Peak Efficiency UNIT % 26 % 200 220 kHz 600 660 kHz 1.2 1.32 MHz 90 % REFERENCE IMATCH Channel-to-Channel Current Matching Channels are in a single IC, ILED: 100mA -2 IACC Absolute Current RISET1/2 = 28.7kΩ -3 ±1 2 % 3 % FAULT DETECTION VSC Channel Short Circuit Threshold V TEMP Over-Temperature Threshold V TEMP_ACC Over-Temperature Threshold Accuracy VOVP_OUT Overvoltage Limit on OVP Pin VOVP_IN Overvoltage Limit on VIN Pin 7.2 1.18 8 8.8 V 150 °C 5 °C 1.22 1.24 35 V V DIGITAL I/O LOGIC LEVEL SPECIFICATIONS VIL Logic Input Low Voltage - STV, EN_PS, EN_VSYNC, EN_ADIM, PWMI, CSEL, EN VIH Logic Input High Voltage - STV, EN_PS, EN_VSYNC, EN_ADIM, PWMI, CSEL, EN STV Frame frequency 0.8 V 1.5 5.5 V 30 240 Hz CURRENT SOURCES VHEADROOM Dominant Channel Current Source Headroom at CH Pin ILED = 160mA TA = +25°C VISET1,2 Voltage at ISET1 and 2 Pins 1.18 ILED_MAX Maximum LED Current per Channel 160 0.75 1.21 V 1.24 V mA PWM GENERATOR fPWM Generated PWM Frequency (See Equation 3) RPWM_SET = 333kΩ Dimming Range PWM Dimming Duty Cycle Limits fPWMI PWMI Input Frequency Range VPWM_SET PWM_SET Voltage VACTL Analog Dimming Input tPWM_MIN 45 50 RPWM_SET = 3.3kΩ 4.5 5 fPWM ≤ 20kHz 0.1 60 55 Hz 5.5 kHz 100 % 20k Hz 1.18 1.21 1.25 V 0% Dimming 0.28 0.3 0.31 V 100% Dimming 2.95 3 3.1 V RPWM_SET = 3.3kΩ Minimum PWM On Time in Direct PWM Mode 350 ns NOTES: 9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 10. At maximum VIN of 32V, minimum VOUT is 35V. Minimum VOUT can be lower at lower VIN. 7 FN7714.1 September 27, 2012 ISL97687 Typical Performance Curves 100 100 4P14S 90 4P18S 85 80 90 VIN = 19V 85 80 75 75 70 VIN = 24V 95 EFFICIENCY (%) EFFICIENCY (%) 95 5 10 15 20 25 INPUT VOLTAGE (V) 30 FIGURE 4. EFFICIENCY vs VIN (ICH: 100mA, fDIM: 200Hz, VOUT: 45V FOR 4P14S AND 55V FOR 4P18S) 100 70 35 30 50 70 90 110 130 CHANNEL CURRENT (mA) 150 170 FIGURE 5. EFFICIENCY vs ICH (VOUT: 55V FOR 4P18S, fDIM:200Hz) 1.0 fDIM = 200Hz 0.5 fDIM = 1kHz 80 ACCURACY (%) EFFICIENCY (%) 90 70 60 CH2 CH3 CH1 0.0 -0.5 50 40 CH4 0 20 40 60 80 -1.0 100 0 20 110 10 100 9 fDIM = 1kHz 80 70 fDIM = 200Hz 60 50 40 30 20 80 100 8 7 6 5 fDIM = 1kHz 4 3 fDIM = 200Hz 2 1 10 0 60 FIGURE 7. ACCURACY vs PWM DIMMING (VIN: 24V, VOUT: 55V FOR 4P18S, ICH: 100mA) CHANNEL CURRENT (mA) CHANNEL CURRENT (mA) FIGURE 6. EFFICIENCY vs PWM DIMMING (VIN: 24V, VOUT: 55V FOR 4P18S, ICH: 100mA) 90 40 DIMMING DUTY CYCLE (%) DIMMING DUTY CYCLE (%) 0 20 40 60 80 100 DIMMING DUTY CYCLE (%) FIGURE 8. PWM DIMMING LINEARITY (VIN: 24V, VOUT: 55V FOR 4P18S) 8 0 0 2 4 6 8 10 DIMMING DUTY CYCLE (%) FIGURE 9. PWM DIMMING LINEARITY (VIN: 24V, VOUT: 55V FOR 4P18S) FN7714.1 September 27, 2012 ISL97687 Typical Performance Curves (Continued) V_PWMI I_INDUCTOR V_OUT V_LX I_CH V_CH1 V_CH I_CH2 FIGURE 10. START-UP (DIRECT PWM DIMMING, VIN: 19V, ICH: 120mA, LEDs: 4P18S, fDIM: 200Hz) I_INDUCTOR FIGURE 11. DIRECT PWM DIMMING (VIN: 19V, LEDs: 4P18S, fDIM: 200Hz) I_INDUCTOR V_OUT V_OUT I_CH1 I_CH1 V_CH2 V_CH2 FIGURE 12. START-UP WITHOUT PHASE SHIFT (VIN : 19V, ICH: 120mA, LEDs: 4P18S, fDIM: 200Hz) V_CH1 FIGURE 13. START-UP WITH PHASE SHIFT (V IN : 19V, ICH: 120mA, LEDs: 4P18S, fDIM: 200Hz) V_CH1 I_INDUCTOR I_INDUCTOR I_CH2 FIGURE 14. PWM DIMMING WITHOUT PHASE SHIFT (VIN: 19V, ICH: 120mA, LEDs: 4P18S, fDIM: 200Hz) 9 I_CH2 FIGURE 15. PWM DIMMING WITH PHASE SHIFT (VIN: 19V, ICH: 120mA, LEDs: 4P18S, f DIM: 200Hz) FN7714.1 September 27, 2012 ISL97687 Typical Performance Curves (Continued) I_INDUCTOR I_INDUCTOR V_STV V_STV V_CH1 V_CH1 V_CH2 V_CH2 FIGURE 16. VSYNC ENABLED DIMMING WITHOUT PHASE SHIFT (VIN: 19V, ICH: 120mA, LEDs: 4P18S, 180Hz OUTPUT PHASE AND FREQUENCY LOCKED TO 60Hz STV) FIGURE 17. VSYNC ENABLED WITH PHASE SHIFT (VIN: 19V, ICH: 120mA, LEDs: 4P18S, 180Hz OUTPUT PHASE AND FREQUENCY LOCKED TO 60Hz STV) V_CH V_PWM I_INDUCTOR I_CH I_CH FIGURE 18. PWM SWITCHING AND TRANSIENT RESPONSE OF INDUCTOR CURRENT 10 FIGURE 19. MINIMUM DIMMING DUTY CYCLE (0.05%, f DIM: 500Hz, ICH = 120mA, DIRECT PWM MODE) FN7714.1 September 27, 2012 ISL97687 Theory of Operation PWM Boost Converter The current mode PWM boost converter produces the minimal voltage needed to enable the LED string with the highest forward voltage drop to run at the programmed current. The ISL97687 employs current mode control boost architecture that has a fast current sense loop and a slow voltage feedback loop. The number of LEDs that can be driven by ISL97687 depends on the type of LED chosen in the application. The ISL97687 is capable of boosting up to greater than 70V and driving 4 Channels of LEDs at a maximum of 160mA per channel. resistors. These parameters are optimized for current matching and absolute current accuracy. However, the absolute accuracy is additionally determined by the external RISET. A 0.1% tolerance resistor is therefore recommended. OVP and VOUT The Overvoltage Protection (OVP) pin has a function of setting the overvoltage trip level as well as limiting the VOUT regulation range. The ISL97687 OVP threshold is set by RUPPER and RLOWER as shown in Equation 1: 1.21 ( R UPPER + R LOWER ) V OUT_OVP = ------------------------------------------------------------------R LOWER (EQ. 1) and VOUT can only regulate between 30% and 100% of the VOUT_OVP such that: Allowable VOUT = 30% to 100% of VOUT_OVP For example, a 1MΩ RUPPER and 19kΩ RLOWER sets OVP to 65.9V. The boost can regulate down to 30% of OVP, so it can go as low as 19.5V. If VOUT needs to be lower than this, the OVP level must be reduced. Otherwise, VOUT will regulate to 19.5V, and the ISL97687 may overheat. However, it’s recommended that the OVP be set to no more than 20% above the nominal operating voltage. This prevents the need for output capacitor voltage ratings and the inductor current rating to be set significantly higher than needed under normal conditions, allowing a smaller and cheaper solution, as well as keeping the maximum voltages and currents that can be seen in the system during fault conditions at less extreme levels. Parallel capacitors should be placed across the OVP resistors such that RUPPER /RLOWER = CLOWER /CUPPER . Using a CUPPER value of at least 30pF is recommended. These capacitors reduce the AC impedance of the OVP node, which is important when using high value resistors. The ratio of the OVP capacitors should be the inverse of the OVP resistors. For example, if RUPPER/RLOWER = 33/1, then CUPPER /C LOWER = 1/33 with CUPPER = 100pF and CLOWER = 3.3nF. These components are not always needed, but it is highly recommended to include placeholders. Current Matching and Current Accuracy The LED current in each channel is regulated using an active current source circuit, as shown in Figure 20. The peak LED current is set by translating the RISET current to the output with a scaling factor of 2919/RISET. The drain terminals of the current source MOSFETs are designed to run at 750mV to optimize power loss versus accuracy requirements. The sources of channel-to-channel current matching error come from the op amp offsets, reference voltage, and current source sense 11 + - REF + - RISET + - PWM DIMMING FIGURE 20. SIMPLIFIED CURRENT SOURCE CIRCUIT Dynamic Headroom Control The ISL97687 features a proprietary dynamic headroom control circuit that detects the highest forward voltage string, or effectively the lowest voltage from any of the CH pins. The system will regulate the output voltage to the correct level to allow the channel with the lowest voltage to have just sufficient headroom to correctly regulate the LED current. Since all LED strings are connected to the same output voltage, the other CH pins will have a higher voltage, but the regulated current source circuit on each channel will ensure that each channel has the correct current level. The output voltage regulation is dynamic, and is updated as needed, to allow for temperature and aging effects in the LEDs. Dimming Controls The ISL97687 provides two basic ways to control the LED current, and therefore, the brightness. These are described in detail in subsequent sub-sections, but can be broadly divided into the following two types of dimming: Step 1. LED DC current adjustment Step 2. PWM chopping of the LED current defined in Step 1 LED DC Current Setting The initial brightness should be set by choosing an appropriate value for the resistor on the ISET1/2 pins. This resistor must connect to AGND, and should be chosen to fix the maximum possible LED current: 2919 I LEDmax = --------------R ISET (EQ. 2) The ISL97687 includes two built-in levels of current, individually set by the resistors on ISET1 and ISET2, according to Equation 2, which can be switched between by using the CSEL pin. FN7714.1 September 27, 2012 ISL97687 Additionally, phase shift mode can be enabled in all configurations except direct PWM, allowing the LED strings to turn on in sequence. CSEL = 0: The current setting is based on ISET1 CSEL = 1: The current setting is based on ISET2 This is typically used in 3D systems to provide a higher current level in 3D modes, but is not restricted to this application. CSEL can be switched in operation and updates immediately in direct PWM mode, and at the start of the next PWM dimming cycle in other modes. LED DC DIMMING It is possible to control the LED current by applying a DC voltage VDIM to the ISET1/2 pin via a resistor as in Figure 21. ISET VISET: 1.21V VDIM RDIM RISET FIGURE 21. LED CURRENT CONTROL WITH VDIM If the VDIM is above VISET 1.21V, the brightness will reduce, and vice versa. In this configuration, it is important that the control voltage be set to the maximum brightness (minimum voltage) level when the ISL97687 is enabled, even if the LEDs are not lit at this point. This is necessary to allow the chip to calibrate to the maximum current level that will need to be supported. Otherwise, on-chip power dissipation will be higher at current levels above the start-up level. Dimming with this technique should be limited to a minimum of 10~20% brightness, as LED current accuracy is increasingly degraded at lower levels. LED PWM CONTROL The ISL97687 provides many different PWM dimming methods. Each of these results in PWM chopping of the current in the LEDs of all 4 channels, to provide an average LED current and control the brightness. During the on-periods, the LED peak current will be defined by the value of the resistor on ISET1 or ISET2, as described in Equation 2. LED PWM DIMMING IN DIRECT PWM MODE When the PWM_SET/PLL pin is tied to VDC, the PWMI input signal is used to directly control the LEDs. The dimming frequency and phase of the LEDs will be the same as that of PWMI. This mode can be used to get very high effective PWM resolution, as the resolution is effectively determined by the PWMI signal source. LED PWM DIMMING – DUTY CYCLE CONTROL In non-direct PWM mode, the ISL97687 can decode the incoming PWMI duty cycle information at 10-bit resolution and the ACTL voltage level at 8-bit resolution and apply these values to the LEDs as a PWM output at a new frequency. For applications where DC-PWM dimming is required, the analog dimming mode must be enabled (EN_ADIM = high). The analog control input pin (ACTL) must then be fed with a voltage of 0.3V to 3.0V. This is decoded as an 8-bit duty cycle of 0% to 100% respectively. This interface supports backward compatibility with CCFL backlight driving systems, but can also be used in other applications, such as analog ALS interfaces. External circuitry can be used to shift most analog input ranges to the required level. Figure 22 is an example that maps a 0V to 3.5V input to give a 10-100% output range, but this can be tailored to other requirements. The PWM dimming frequency, set by the PWM_SET pin, should be at least 1kHz when EN_ADIM is high. In Analog mode, the decoded 10-bit PWM duty cycle information from the PWMI pin is also used, multiplied by the 8-bit level decoded from the ACTL pin. For example, if ACTL = 2.3V (74%) and PWMI = 50%, then LED dimming will be 74% x 50% = 37%. For analog dimming applications where this multiplication is not needed, PWMI should be tied high, giving the ACTL pin full control over the duty cycle range. For applications where analog dimming is not needed, EN_ADIM should be low and PWMI should be driven with the required duty cycle. Dimming can either be “direct PWM” mode, where both the frequency and duty cycle of the LEDs match that of the incoming PWMI signal, or the duty cycle and frequency sources must be selected from the following. SUPPORTED LED DUTY CYCLE SOURCES • Decoded PWMI pin duty cycle (PWM input mode) • Decoded ACTL pin voltage (Analog input mode) • Analog*PWM input mode (Both PWM and Analog inputs are used) SUPPORTED LED FREQUENCY SOURCES • Free running internal oscillator (Internal PWM frequency mode) • Frequency can be phase and frequency locked to frame rate (VSYNC mode) 12 FIGURE 22. EXAMPLE OF ACTL INPUT ADJUSTMENT FN7714.1 September 27, 2012 ISL97687 PWM Dimming Frequency Adjustment Phase Shift Control The dimming frequencies of serial interface and ACTL modes are set by an external resistor at the PWM_SET pin, as shown in Equation 3: The ISL97687 is capable of delaying the phase of each current source within the PWM cycle. Conventional LED drivers present the worst load transients to the boost converter, by turning on all channels simultaneously, as shown in Figure 23. The ISL97687 can be configured to phase shift each channel by 90°, individually turning them on and off at different points during the PWM dimming period, as shown in Figure 24. At duty cycles below 100%, the load presented to the boost will peak at a lower level and/or spend less time at the peak, when compared to that of a conventional LED driver, as shown in Figure 23. Additionally, load steps are limited to the LED current of one CH pin, one quarter of that of a standard driver. This can help reduce transients on VOUT and also reduces audio noise by limiting the magnitude of changes in magnetic field required in the inductor needed to track the load. Audio noise is also generally improved for PWM frequencies in the audio band, as the effective frequency of the boost load is multiplied by a factor of 4, meaning that, for example, a 5kHz LED frequency offers an effective boost load frequency of 20kHz. 7 ( 1.665 ) ×10 f PWM = --------------------------------R PWMSET (EQ. 3) where fPWM is the desirable PWM dimming frequency and RPWMSET is the setting resistor. VSYNC FUNCTION The VSYNC function is used to provide accurate LED dimming frequencies and make sure that the video data is properly aligned with the frame rate. A phase locked loop (PLL) is used to lock the frequency to a multiple of the frame rate. Additionally, the phase of the PWM output is aligned with the frame rate to provide very predictable video performance. In VSYNC mode, the PWM_SET/PLL pin is used as the PLL loop compensation pin and needs a loop filter connected between it and ground. Frame rates between 30Hz and 300Hz are supported, and an automatic frequency detection circuit will provide the same output frequency at 30, 60, 120, 180, 240, and 300Hz. Additionally, the PWM dimming frequency can be pre-selected to any of the following values shown in Table 1 (Note that for the 60Hz range, the frequencies will be scaled by a factor of framerate/60Hz and for the 120Hz range they will be scaled by a factor of framerate/120Hz). ICH4 ICH3 ICH2 ICH1 TABLE 1. PRE-SELECTED PWM DIMMING FREQUENCY AT VSYNC MODE ICH_TOTAL DIMMING FREQUENCY (Hz) (kHz) (kHz) (kHz) 180 1.26 5.70 13.38 240 1.38 6.18 13.86 300 1.50 6.66 14.34 360 1.62 7.14 14.82 420 1.74 7.62 15.30 480 1.86 8.10 15.78 540 1.98 8.58 16.26 600 2.10 9.06 16.74 660 2.34 9.54 17.22 720 2.58 10.02 17.70 780 2.88 10.50 18.18 840 3.36 10.98 18.66 900 3.78 11.46 19.14 960 4.20 11.94 19.62 1.02k 4.74 12.42 20.10 1.14k 5.22 12.90 20.58 TIME FIGURE 23. NON PHASE SHIFT PWM DIMMING AT 50% DUTY CYCLE ICH4 ICH3 ICH2 ICH1 ICH_TOTAL TIME FIGURE 24. PHASE SHIFT PWM DIMMING AT 50% DUTY CYCLE VOUT Control when LEDs are Off When the backlight is enabled but all LEDs are off (i.e., during the PWM off times), the switching regulator of a typical LED drivers will stop switching, which can allow the output to begin to discharge. 13 FN7714.1 September 27, 2012 ISL97687 This is not a problem when the LED off times are short and the duty cycle is running at a high duty cycle, or the output capacitance is large. However, it presents two problems. First, for low duty cycles at low frequencies, VOUT can droop between on-times, resulting in under-regulation of the current when the LEDs are next switched on. Second, at high PWM frequencies or very low duty cycles, LED on-times can be shorter than the minimum number of boost cycles needed to ramp up the inductor current to the required level to support the load. For example, a 1% on-time while running at 20kHz PWM dimming frequency is only 500ns. If the boost switching frequency is set at 500kHz, this only represents a quarter of a switching cycle per LED on-time, which may not be sufficient to ramp the inductor current to the required level. The ISL97687 incorporates an additional PFM switching mechanism that allows the boost stage to continue to switch at low current levels in order to replace the energy lost from the output capacitor due to the OVP stack resistance and capacitor self discharge. For very short pulses, this also means that the charge delivered to the LEDs in the on-times is provided entirely by the output capacitor, kept at the correct voltage by the PFM mode in the off-times. This allows the output to always remain very close to the required level, so that when the LEDs are re-enabled, the boost output is already at the correct level. This dramatically improves LED PWM performance, providing industry leading linearity down to sub 1% levels, and reduces the overshoot in the boost inductor current, caused by transient switching when the LEDs are switched on, to a minimum level. The system will continue to maintain VOUT at the target level for 120ms after the last time the LEDs were on. If all LEDs are off for a longer period than this, the converter will stop switching and go into a sleep mode, allowing VOUT to decay, in order to save power during long backlight-off periods. Switching Frequency The boost switching frequency can be adjusted by the resistor on the OSC pin, which must be connected to AGND, and follows Equation 4: 10 (EQ. 4) ( 5 ×10 ) f SW = -----------------------R OSC where fSW is the desirable boost switching frequency and ROSC is the setting resistor. 5V and 2.4V Low Dropout Regulators A 5V LDO regulator is used to provide the low voltage supply needed to drive internal circuits. The output of this LDO is the VDC pin. A decoupling capacitor of 1µF or more is required between this pin and AGND for correct operation. Similarly, a 2.4V LDO regulator is present at the VLOGIC pin, and also requires a 1µF decoupling capacitor. Both pins can be used as a coarse voltage reference, or as a supply for other circuits, but can only support a load of up to ~10mA and should not be used to power noisy circuits that can feed significant noise onto their supply. Soft-Start and Boost Current Limit The boost current limit should be set by using a resistor from CS to PGND. The typical current limit can be calculated as: 0.17 I LIMIT = -----------R CS (EQ. 5) The CS resistor should be chosen based on the maximum load that needs to be driven. Typically, a limit of 30~40% more than is required under DC conditions is sufficient to allow for necessary overshoots during load transients. Values of 20~100mΩ are supported. It is important that PGND pin 14 (QFN)/18 (SOIC) is connected directly to the base of the sense resistor, with no other connection to the ground system, except via this path. This is because this pin is used as a ground reference for the CS pin. Connecting it here gives the maximum noise immunity and the best stability characteristics. The ISL97687 uses a digital current limit based soft start. The initial limit level is set to one ninth of the full current limit, with eight subsequent steps increasing this by a ninth of the final value every 2ms until it reaches the full limit. In the event that no LEDs have been conducting during the interval since the last step (for example if the LEDs are running at low duty cycle at low PWM frequency), the step will be delayed until the LEDs are conducting again. If the LEDs are off for more than 120ms, making the converter go into sleep mode, soft-start will be restarted when the LEDs are re-enabled. Fault Protection and Monitoring The ISL97687 features extensive protection functions to cover all perceivable failure conditions. The failure mode of an LED can be either open or short circuit. The behavior of an open circuit LED can additionally take the form of either infinite or very high resistance or, for some LEDs, a zener diode, which is integrated into the device, in parallel with the now opened LED. For basic LEDs (which do not have built-in zener diodes), an open circuit LED failure will only result in the loss of one channel of LEDs, without affecting other channels. Similarly, a short circuit condition on a channel that results in that channel being turned off does not affect other channels, unless a similar fault is occurring. Due to the lag in boost response to any load change at its output, certain transient events (such as significant step changes in LED duty cycle, or a change in LED current caused by CSEL switching) can transiently look like LED fault modes. The ISL97687 uses feedback from the LEDs to determine when it is in a stable operating region and prevents apparent faults during these transient events from allowing any of the LED strings to fault out. See Figure 26 and Table 2 for more details. Short Circuit Protection (SCP) The short circuit detection circuit monitors the voltage on each channel and disables faulty channels which are detected to be more than the short circuit threshold, 8V above the lowest CH pin, following a timeout period. 14 FN7714.1 September 27, 2012 ISL97687 Open Circuit Protection (OCP) VIN OVP When any of the LEDs become open circuit during the operation, that channel will be disabled after a timeout period, and the part will continue to drive the other channels. The ISL97687 monitors the current in each channel such that any string which reaches the intended output current is considered “good”. Should the current subsequently fall below the target, the channel will be considered an “open circuit”. Furthermore, should the boost output of the ISL97687 reach the OVP limit, all channels which are not “good” will be timed out. If VIN exceeds 35V, the part will be shut down until power or EN is cycled. At this point, all digital settings will be reset to their default states. Unused CH pins should be grounded, which will disable them from start-up. This will prevent VOUT having to ramp to OVP at start-up, in order to determine that they are open. Undervoltage Lock-out If the input voltage falls below the UVLO level of 2.8V, the device will stop switching and reset. Operation will restart, with all digital settings returning to their default states, once the input voltage is back in the normal operating range. Shutdown When the EN pin is low the entire chip is shut down to give close to zero shutdown current. The digital interfaces will not be active during this time. The EN can be high before VIN. COMPENSATION The ISL97687 boost regulator uses a current mode control architecture, with an external compensation network connected to the COMP pin. The component values shown in Figure 25 should be used. The network comprises a 47pF capacitor from COMP to AGND, in parallel with a series RC of 25kΩ and 2.2nF, also from COMP to AGND. Over-Temperature Protection (OTP) The OTP threshold is set to +150°C. When this is reached, the boost will stop switching and the output current sources will be switched off and stay off until power or EN is cycled. For the extensive fault protection conditions, please refer to Figure 26 and Table 2. COM P 2.2nF 47pF 25k FIGURE 25. COMPENSATION NETWORK VOUT LX FAULT IMAX ILIMIT O/P SHORT LOGIC OVP FET DRIVER VSC CH1 VSET/2 REG CH4 THRM SHDN REF OTP T2 TEMP SENSOR T1 VSET + Q1 VSET PWM1/OC1/SC1 + Q4 PWM4/OC4/SC4 PWM CONTROL FIGURE 26. SIMPLIFIED FAULT PROTECTIONS 15 FN7714.1 September 27, 2012 ISL97687 TABLE 2. PROTECTIONS TABLE CASE FAILURE MODE DETECTION MODE FAILED CHANNEL ACTION GOOD CHANNELS ACTION VOUT REGULATED BY 1 CH1 Short Circuit CH1 ON and burns power Over-Temperature Protection limit (OTP) not triggered and VCH1 < VSC CH2 through CH4 Normal Highest VF of CH2 through CH4 2 CH1 Short Circuit OTP not triggered but VCH1 > VSC If 3 channels are already shut down, all channels will be shut down. Otherwise CH2-4 will remain as normal Highest VF of CH2 through CH4 3 CH1 Open Circuit with OTP not triggered and infinite resistance VCH1 < VSC VOUT will ramp to OVP. CH1 will time-out CH2 through CH4 Normal after 6 PWM cycles and switch off. VOUT will drop to normal level. Highest VF of CH2 through CH4 4 CH1 Open Circuit with OTP triggered and VCH1 < VSC infinite resistance during operation All IC shut down VOUT disabled 5 CH1 LED Open Circuit OTP not triggered and VCH1 < VSC but has paralleled Zener CH1 remains ON and has highest VF, CH2 through CH4 ON, Q2 through VF of CH1 thus VOUT increases Q4 burn power. CH2-4 will fault out if they reach VSC as a result of VOUT increase due to increase VF in CH1 6 CH1 LED Open Circuit OTP not triggered but VCHx > VSC but has paralleled Zener CH1 remains ON and has highest VF, VOUT increases then CH-X VF of CH1 thus VOUT increases. switches OFF. This is an unwanted shut off and can be prevented by setting OVP at an appropriate level. 7 Channel-to-Channel ΔVF too high OTP triggered but VCHx < VSC All channels switched off 8 Output LED string voltage too high VOUT reaches OVP and not Driven with normal current. Any channel that is below the target current VOUT disabled sufficient to regulate LED will time-out after 6 PWM cycles. (Note: Time-out can be longer than 6 PWM cycles in case direct PWM current mode) 9 VOUT/SW shorted to GND CH1 disabled after 6 PWM cycles time-out. (Note: Time-out can be longer than 6 PWM cycles in direct PWM mode) VOUT disabled SW will not switch if started up in this condition. VOUT shorted to ground during operation will also cause the converter to shut down Component Selections Input Capacitor According to the inductor Voltage-Second Balance principle, the change of inductor current during the power MOSFET switching on-time is equal to the change of inductor current during the power MOSFET switching off-time under steady state operation. The voltage across an inductor is shown in Equation 6: Switching regulators require input capacitors to deliver peak charging current and to reduce the impedance of the input supply. This reduces interaction between the regulator and input supply, thereby improving system stability. The high switching frequency of the loop causes almost all ripple current to flow in the input capacitor, which must be rated accordingly. V L = L × ΔI L ⁄ Δt (EQ. 6) and ΔIL @ tON = ΔIL @ tOFF, therefore: ( V I – 0 ) ⁄ L × D × t Sw = ( V O – V D – V I ) ⁄ L × ( 1 – D ) × t Sw (EQ. 7) where D is the switching duty cycle defined by the turn-on time over the switching period. VD is a Schottky diode forward voltage, which can be neglected for approximation. tsw is the switching period where tsw = 1/fsw, and the fsw is the switching frequency of the boost converter. Rearranging the terms without accounting for VD gives the boost ratio and duty cycle respectively as Equations 8 and 9: VO ⁄ VI = 1 ⁄ ( 1 – D ) (EQ. 8) D = ( VO – VI ) ⁄ VO (EQ. 9) 16 A capacitor with low internal series resistance should be chosen to minimize heating effects and improve system efficiency, such as X5R or X7R ceramic capacitors, which offer small size and a lower value of temperature and voltage coefficient compared to other ceramic capacitors. During the normal continuous conduction mode of the boost converter, its input current flows continuously into the inductor; AC ripple component is only proportional to the rate of the inductor charging, thus, smaller value input capacitors may be used. It is recommended that an input capacitor of at least 10µF be used. Ensure the voltage rating of the input capacitor is suitable to handle the full supply range. FN7714.1 September 27, 2012 ISL97687 Inductor The selection of the inductor should be based on its maximum current (ISAT) characteristics, power dissipation, EMI susceptibility (shielded vs unshielded), and size. Inductor type and value influence many key parameters, including the inductor ripple current, current limit, efficiency, transient performance and stability. The inductor’s maximum current capability must be large enough to handle the peak current at the worst case condition. If an inductor core is chosen with a lower current rating, saturation in the core will cause the effective inductor value to fall, leading to an increase in peak to average current level, poor efficiency and overheating in the core. The series resistance, DCR, within the inductor causes conduction loss and heat dissipation. A shielded inductor is usually more suitable for EMI susceptible applications, such as LED backlighting. The peak current can be derived from the voltage across the inductor during the off period, as expressed in Equation 10: IL peak = ( V O × I O ) ⁄ ( 85% × V I ) + 1 ⁄ 2 [ V I × ( V O – V I ) ⁄ ( L × V O × f SW ) ] (EQ. 10) The choice of 85% is just an average term for the efficiency approximation. The first term is the average current, which is inversely proportional to the input voltage. The second term is the inductor current change, which is inversely proportional to L and fSW. As a result, for a given switching frequency, minimum input voltage must be used to calculate the input/inductor current as shown in Equation 10. For a given inductor size, the larger the inductance value, the higher the series resistance because of the extra number of turns required, thus, higher conductive losses. The ISL97687 current limit should be less than the inductor saturation current. Output Capacitors can be reduced to 10%~20% of its rated capacitance at the maximum voltage. Because of this, Y5V type ceramic capacitors should be avoided. A larger output capacitor will also ease the driver response during PWM dimming off period due to the longer sample and hold effect of the output drooping. The driver does not need to boost as much on the next on period, which minimizes transient current. The output capacitor also plays an important role for system compensation. Channel Capacitor It is recommended to use at least 1nF capacitors from CH pins to VOUT. Larger capacitors will reduce LED current ripple at boost frequency, but will degrade transient performance at high PWM frequencies. The best value is dependant on PCB layout. Up to 4.7nF is sufficient for most configurations. Schottky Diode A high speed rectifier diode is necessary to prevent excessive voltage overshoot, especially in the boost configuration. Low forward voltage and reverse leakage current will minimize losses, making Schottky diodes the preferred choice. Although the Schottky diode turns on only during the boost switch off period, it carries the same peak current as the inductor, therefore, a suitable current rated Schottky diode must be used. High Current Applications Each channel of the ISL97687 can support up to 160mA. For applications that need higher current, multiple channels can be grouped to achieve the desirable current. For example, in Figure 27, the cathodes of the last LEDs can be connected to CH1/CH2 and CH3/CH4, this configuration can be treated as a single string with up to 350mA current driving capability. BOOST OUTPUT The output capacitor acts to smooth the output voltage and supplies load current directly during the conduction phase of the power switch. Output ripple voltage consists of the discharge of the output capacitor during the FET turn-on period and the voltage drop due to load current flowing through the ESR of the output capacitor. The ripple voltage is shown in Equation 11: ΔV CO = ( I O ⁄ C O × D ⁄ fSw ) + ( I O × ESR ) (EQ. 11) where IO represents the output current, CO is the output capacitance, D is the duty ratio as described in Equation 9. ESR is the equivalent series resistance of the output capacitance and fsw is the switching frequency of the converter. Equation 11 shows the importance of using a low ESR output capacitor for minimizing output ripple. As shown in Equation 11, the output ripple voltage, ΔVCo, can be reduced by increasing the output capacitance, CO or the switching frequency, fSW, or using output capacitors with small ESR. In general, ceramic capacitors are the best choice for output capacitors in small to medium sized LCD backlight applications due to their cost, form factor, and low ESR. CH1 CH2 CH3 CH4 FIGURE 27. GROUPING MULTIPLE CHANNELS FOR HIGH CURRENT APPLICATIONS The choice of X7R over Y5V ceramic capacitors is highly recommended because the X7R type capacitor is less sensitive to capacitance change overvoltage. Y5V’s absolute capacitance 17 FN7714.1 September 27, 2012 ISL97687 PCB Layout Considerations Two Layers PCB Layout with TQFN Package Great care is needed in designing a PC board for stable ISL97687 operation. As shown in the typical application diagram (Figure 1, page 1), the separation of PGND and AGND of each ISL97687 is essential, keeping the AGND referenced only local to the chip. This minimizes switching noise injection to the feedback sensing and analog areas, as well as eliminating DC errors form high current flow in resistive PC board traces. PGND and AGND should be on the top and bottom layers respectively in the two layer PCB. A star ground connection should be formed by connecting the LED ground return and AGND pins to the thermal pad with 9-12 vias. The ground connection should be into this ground net, on the top plane. The bottom plane then forms a quiet analog ground area, that both shields components on the top plane, as well as providing easy access to all sensitive components. For example, the ground side of the ISET1/2 resistors can be dropped to the bottom plane, providing a very low impedance path back to the AGND pin, which does not have any circulating high currents to interfere with it. The bottom plane can also be used as a thermal ground, so the AGND area should be sized sufficiently large to dissipate the required power. For multi-layer boards, the AGND plane can be the second layer. This provides easy access to the AGND net, but allows a larger thermal ground and main ground supply to come up through the thermal vias from a lower plane. OVP connection then needs to be as short as possible to the pin. The AGND connection of the lower OVP components is critical for good regulation. At 70V output, a 100mV change at VOUT translates to a 1.7mV change at OVP, so a small ground error due to high current flow, if referenced to PGND, can be disastrous. 5. The bypass capacitors connected to VDC and VLOGIC need to be as close to the pin as possible, and again should be referenced to AGND. This is also true for the COMP network and the rest of the analog components (on ISEDT1/2, FPWM, etc.). 6. The heat of the chip is mainly dissipated through the exposed thermal pad so maximizing the copper area around it is a good idea. A solid ground is always helpful for the thermal and EMI performance. 7. The inductor and input and output capacitors should be mounted as tight as possible, to reduce the audible noise and inductive ringing. General Power PAD Design Considerations Figure 28 shows an example of how to use vias to remove heat from the IC. We recommend you fill the thermal pad area with vias. A typical via array would be to fill the thermal pad foot print with vias spaced such that the centre to centre spacing is three times the radius of the via. Keep the vias small, but not so small that their inside diameter prevents solder wicking through the holes during reflow. This type of layout is particularly important for this type of product, as the ISL97687 has a high power boost, resulting in high current flow in the main loop’s traces. Careful attention should be focussed on the below layout details: 1. Boost input capacitors, output capacitors, inductor and Schottky diode should be placed together in a nice tight layout. Keeping the grounds of the input, output, ISL97687 and the current sense resistor connected with a low impedance and wide metal is very important to keep these nodes closely coupled. 2. Figure 29 shows important traces of current sensor (RS) and OVP resistors (RU, RL). The current sensor track line should be short, so that it remains as close as possible to the Current Sense (CS) pin. Additionally, the CS pin is referenced from the adjacent PGND pin. It is extremely important that this PGND pin is placed with a good reference to the bottom of the sense resistor. In Figure 29 you can see that this ground pin is not connected to the thermal pad, but instead used to effectively sense the voltage at the bottom of the current sense resistor. However, this pin also takes the gate driver current, so it must still have a wide connection and a good connection back from the sense resistor to the star ground. Also, the RC filter on CS should be placed referenced to this PGND pin and be close to the chip. 3. If possible, try to maintain central ground node on the board and use the input capacitors to avoid excessive input ripple for high output current supplies. The filtering capacitors should be placed close by the VIN pin. 4. For optimum load regulation and true VOUT sensing, the OVP resistors should be connected independently to the top of the output capacitors and away from the higher dv/dt traces. The 18 FIGURE 28. ISL97687 TQFN PCB VIA PATTERN One Layer PCB Layout with SOIC Package The general rules of two layer PCB layout can be applied to the one layer PCB layout of the SOIC package, although this layout is much more challenging and very easy to get wrong. The noisy PGND of the switching FET area and quiet AGND must be placed on the same plane as shown in Figure 30, therefore, great care must be taken to maintain stable and clean operation, due to increased risk of noise injection to the quiet area. 1. The GND plane should be extended as far as possible as space allows to spread out heat dissipation. 2. All ground pads for input caps, current sensor, output caps should be close to the PGND pin adjacent to the CS pin of ISL97687 with wide metal connection shown in the Figure 30. This guarantees a low differential voltage between these critical points. 3. The connection point between AGND pin 14 and PGND pin 18 should be “ Narrow” neck, effectively making a star ground at the AGND pin. FN7714.1 September 27, 2012 ISL97687 4. The relatively quiet AGND area, to the right of the neck needs to be traced out carefully in unbroken metal, via the shortest possible path to the ground side of the components connected to OVP, COMP, ISET, PWM_SET/PLL, and ACTL. This is also true for the filtering caps on PWMI and STV. These are needed to reject noise and cause decoding errors in some conditions. 5. The current sensing line is shielded by a metal trace, coming from its source, to prevent pickup from the GD pin beside it. 6. The filtering cap of the current sensing line should be placed close to the CS pin rather than in the area of current sense resistor, as it needs to couple this pin to the adjacent PGND pin. 7. The noisy switching FET should be kept far away from the quiet pin area. 8. The area on the switching node should be determined by the dissipation requirements of the boost power FET. PIN 1 PVIN PGND INDUCTOR DIODE PGND VOUT FIGURE 29. EXAMPLE OF TWO LAYER PCB LAYOUT 19 FN7714.1 September 27, 2012 ISL97687 PVIN PGND VLOGIC EN_PS EN_ADIM STV PWMI CSEL PGND CH1 CH2 9 8 7 6 5 4 3 2 1 VDC 11 EN_VSYNC 10 VIN 12 /SHUT 13 AGND 14 Narrow connection point of PGND and AGND PVOUT All close to each other with wide metal connection Quiet AGND trace 28 CH3 27 CH4 26 PGND 25 ACTL 24 OSC 22 ISET1 23 ISET2 21 COMP 20 OVP 18 PGND 19 PWM_SET/PLL 16 SLEW 17 CS 15 GD FIGURE 30. EXAMPLE OF ONE LAYER PCB LAYOUT 20 FN7714.1 September 27, 2012 ISL97687 Equivalent Circuit Diagrams VIN + VDC + VDC 1000Ω 200Ω 1Ω OSC PWM_SET/PLL 20V 40kΩ VDC VDC 1Ω 200Ω 600Ω ACTL VDC + 2000Ω ISET1 ISET2 GD COMP VLOGIC - 50V VDC 200Ω OVP 600Ω PWMI EN_ADIM 50V 5200Ω EN_VSYNC 2MΩ CSEL 5200Ω STV 6V EN_PS 6V VLOGIC VDC 2MΩ 50kΩ 200Ω EN CS 50V 5V 2MΩ 5µA LX VLOGIC VDC 220kΩ 3V CH1~CH4 VDC 80V + 600Ω - SLEW VIN VDC 6V 50V 21 20µA 20V 80kΩ FN7714.1 September 27, 2012 ISL97687 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE REVISION September 21, 2012 FN7714.1 August 31, 2012 September 15, 2011 CHANGE Corrected PGND symbol in Figures 1 and 3. Corrected conditions for “VIH” in the “Electrical Specifications” table on page 7 from "Logic input low.." to "Logic input high.." Corrected label typo in Figure 20 from "RSET" to "RISET". Corrected "PWMI" and "CSEL" labels in the “Equivalent Circuit Diagrams” on page 21. Added Note 7 and corrected Note reference in “Thermal Information” on page 6 for SOIC from Note 4 to Note 7. Corrected I_CHI1 to V_CH1 in Figures 16 and 17 on page 10. Corrected FPWM pin to PWM_SET/PLL pin in first paragraph of “Vsync Function” on page 13 Added "The PWM dimming frequency, set by the PWM_SET pin, should be at least 1kHz when EN_ADIM is high." to second paragraph of “LED PWM Dimming – Duty Cycle Control” on page 12. FN7714.0 Initial Release Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective product information page. Also, please check the product information page to ensure that you have the most updated datasheet: ISL97687 To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 22 FN7714.1 September 27, 2012 ISL97687 Package Outline Drawing L28.5x5B 28 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 1, 10/07 4X 3.0 5.00 24X 0.50 A B 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 28 22 1 5.00 21 3 .25 ± 0 . 10 15 (4X) 7 0.15 8 14 TOP VIEW 0.10 M C A B 28X 0.55 ± 0.05 4 28X 0.25 ± 0.05 BOTTOM VIEW SEE DETAIL "X" 0.10 C 0 . 75 ± 0.05 C BASE PLANE SEATING PLANE 0.08 C ( 4. 65 TYP ) ( 24X 0 . 50) ( SIDE VIEW 3. 25) (28X 0 . 25 ) C 0 . 2 REF 5 0 . 00 MIN. 0 . 05 MAX. ( 28X 0 . 75) TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 23 FN7714.1 September 27, 2012 ISL97687 Small Outline Plastic Packages (SOIC) M28.3 (JEDEC MS-013-AE ISSUE C) N INDEX AREA 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -Ce A1 B 0.25(0.010) M C 0.10(0.004) C A M B S 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. MILLIMETERS MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.6969 0.7125 17.70 18.10 3 E 0.2914 0.2992 7.40 7.60 4 0.05 BSC 10.00 h 0.01 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 8o 0o 28 0o 10.65 - 0.394 N 0.419 1.27 BSC H a NOTES: MAX A1 e α MIN 28 - 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 24 FN7714.1 September 27, 2012