VISHAY PE30L0FR472MAB

PE30
Vishay Sfernice
Fully Sealed Potentiometer
Military and Professional Grade
FEATURES
•
•
•
•
•
•
•
•
•
•
High power rating 3 W at 70 °C
Low temperature coefficient (150 ppm/°C typical)
Cermet element
Full sealing
Use of faston 2.86 connections
Tests according to CECC 41000 or IEC 60393-1
Wires and connectors available
Custom design on request
Center detent option
Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")
PE30L
8
(0.31)
20 (0.79) max.
12 (0.47)
76°
14 wrench
13 (0.51)
max.
Thread M10 x 0.75
Ø6
(0.24)
0.5
(0.02)
FG = 16 (0.63)
Ø 19.7
(0.78)
a
FL = 25 (0.99)
FR = 50 (1.97)
PE30LL: LPRP - Locating Peg
3
(0.12)
c
R 5.2
(0.20)
3
(0.12)
b
2.85 (0.11)
0.8
(0.3)
Ø 1.8 (0.07)
Ø 10.5
(0.41)
12.5
(0.49)
9.2
(0.36)
PANEL MOUNT
8.8
(0.35)
Ø 3.5
(0.14)
3
(0.12)
PE30ME: Panel Sealed
2.3
(0.9)
23 (0.91) max.
16 (0.63) max.
Sealing ring
0.7 (0.03)
Ø 1.2
(0.05)
Ø 1 (0.4)
Flats
located
8 ± 0.2
(0.31 ± 0.01)
Ø 10.5
(0.41)
Ø6
(0.24)
Ø 19.7
(0.78)
9 (0.35)
FD = 13
(0.61)
PANEL MOUNT
Slot
1 x 1.8
deep
FJ = 22 (0.87)
FP = 47 (1.85)
www.vishay.com
Document Number: 51037
For technical questions, contact: [email protected]
Revision: 29-Aug-12
See also Application Note: www.vishay.com/doc?51001 and www.vishay.com/doc?52029
131
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
Vishay Sfernice
Fully Sealed Potentiometer
Military and Professional Grade
ELECTRICAL SPECIFICATIONS
Resistive Element
Cermet
Electrical Travel
270° ± 10°
22  to 10 M
Linear Taper
Resistance Range
100  to 2.2 M
Logarithmic Taper
Standard Series E3
1 - 2.2 - 4.7 and on request 1 - 2 - 5
Standard
± 20 %
Tolerance
On Request
± 10 % to ± 5 %
% TOTAL RESISTANCE
100
Taper
80
F
60
A
L
40
20
0
0
20
40
60
80
100
% CLOCKWISE SHAFT ROTATION
3
Linear
POWER IN W
LIN. TAPER A
3 W at 70 °C
Power Rating
Logarithmic
1.5 W at 70 °C
2
LOG. TAPER
L and F
1
0
0
20
40
60 70 80
100
120 140
AMBIENT TEMPERATURE IN °C
c
a
Circuit Diagram
(3)
(1)
cw
b
(2)
Temperature Coefficient (Typical)
Limiting Element Voltage
Contact Resistance Variation (Typical)
± 150 ppm/°C
300 V
3 % Rn or 3 
End Resistance (Typical)
1
Dielectric Strength (RMS)
2500 V
Insulation Resistance (300 VDC)
105 M
Independent Linearity (Typical)
±5%
Document Number: 51037
www.vishay.com
For technical questions, contact: [email protected]
132
See also Application Note: www.vishay.com/doc?51001 and www.vishay.com/doc?52029
Revision: 29-Aug-12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
Vishay Sfernice
Fully Sealed Potentiometer
Military and Professional Grade
STANDARD RESISTANCE ELEMENT DATA
STANDARD
RESISTANCE
VALUES
LINEAR TAPER
MAX.
POWER
AT 70 °C
MAX.
WORKING
VOLTAGE
LOGS TAPER
MAX. CUR.
THROUGH WIPER
MAX.
POWER
AT 70 °C
MAX.
WORKING
VOLTAGE
MAX. CUR.
THROUGH WIPER

W
V
mA
W
V
mA
22
47
100
220
470
1K
2.2K
4.7K
10K
22K
47K
100K
220K
470K
1M
2.2M
4.7M
10M
3
3
3
3
3
3
3
3
3
3
1.91
0.90
0.41
0.19
0.09
0.04
0.02
0.01
8.1
11.9
17.3
25.7
37.5
54.8
81.2
119.9
173
257.7
300
300
300
300
300
300
300
300
369
252
173
116
79
54
37
25
17
11
6.3
3
1.36
0.63
0.30
0.13
0.06
0.03
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
0.9
0.41
0.19
0.09
0.04
12.2
18.2
26.6
38.7
57.4
83.9
122
181.6
265
300
300
300
300
300
122
82.6
56.6
38.7
26.1
17.9
12.2
8.25
5.64
3
1.36
0.63
0.30
0.13
MECHANICAL SPECIFICATIONS
Mechanical Travel
300° ± 5°
Operating Torque (Typical)
3 Ncm max.
4.25 oz.-inch max.
End Stop Torque
120 Ncm max.
10.51 lb oz.-inch max.
Tightening Torque of Mounting Nut
250 Ncm max.
22 lb-inch max.
Unit Weight
23 to 32 g max.
0.8 to 1.13 oz.
Terminals
e3: Pure Sn
ENVIRONMENTAL SPECIFICATIONS
Temperature Range
Climatic Category
Sealing
- 55 °C to 125 °C
55/125/56
Fully sealed - Container IP67
OPTIONS
Special Feature Command Shaft
Length is measured from the mounting surface to the free end of the shaft. The screwdriver
slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to
drawings supplied by customers. We recommend that customers should not machine tool
shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided.
Panel Sealing (PE30M)
The panel sealing device consists of a ring located in a groove on the potentiometer face.
Sealing is obtained by tightening the ring against the panel when mounting the
potentiometer.
Old code: PE30P
www.vishay.com
Document Number: 51037
For technical questions, contact: [email protected]
Revision: 29-Aug-12
See also Application Note: www.vishay.com/doc?51001 and www.vishay.com/doc?52029
133
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
Vishay Sfernice
Fully Sealed Potentiometer
Military and Professional Grade
OPTIONS
Location is obtained by fitting a special washer on the mounting face of the potentiometer.
Old code: LPRP
Locating Peg (PE30LL)
The shaft locking device consists of a tapered nut tightening a slotted notched washer
against both bushing and shaft.
DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm.
DBAN is also available with all special types.
This device is normally supplied in a separate bag. Can be pre-mounted on request.
Shaft Locking (PE30LD)
1)
14 wrench
12 wrench
2)
Assembling
Method
6.5
15
CENTER DETENT
• Stable position in mid mechanical travel
• Output ratio 50 % ± 10 %
• Rotational life: 10 000 actuations
Full CW
Full CCW
ORDERING INFORMATION (First order only)
CV1M
MARKING
•
•
•
•
Vishay trademark
Part number (including ohmic value and tolerance code)
Manufacturing date code
Marking of terminals 3, and a, b, c
PERFORMANCES
TESTS
CONDITIONS
TYPICAL VALUES AND DRIFTS
RT/RT (%)
R1-2/R1-2 (%)
OTHER
Electrical Endurance
1000 h at rated power
90'/30' - ambient temp. 70 °C
±1%
-
Contact res. variation: < 3 % Rn
Climatic Sequence
Phase A dry heat 125 °C
Phase B damp heat
Phase C cold - 55 °C
Phase D damp heat 5 cycles
± 0.5 %
±1%
-
Damp Heat, Steady State
56 days
40 °C 93 % HR
± 0.5 %
±1%
Insulation resistance: > 104 M
Change of Temperature
5 cycles
- 55 °C at + 125 °C
± 0.5 %
-
-
Mechanical Endurance
Shock
Vibration
25 000 cycles
±3%
-
Contact res. variation: < 2 % Rn
50 g’s at 11 ms
3 successive shocks
in 3 directions
± 0.1 %
± 0.2 %
-
10 Hz to 55 Hz
0.75 mm or 10 g’s
during 6 h
± 0.1 %
± 0.2 %
-
Document Number: 51037
www.vishay.com
For technical questions, contact: [email protected]
134
See also Application Note: www.vishay.com/doc?51001 and www.vishay.com/doc?52029
Revision: 29-Aug-12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PE30
Vishay Sfernice
Fully Sealed Potentiometer
Military and Professional Grade
ORDERING INFORMATION (Part Number)
P
E
MODEL BUSHING
PE30
3
0
L
B
OPTION
F
G
2
0
OHMIC
VALUE
SHAFT
4
M
TOLERANCE
A law =
For L bushing (= old codes:)
± 20 %
from 22  On request:
FG 16 mm, slotted = AC
to 10 M
FL 25 mm, slotted = AM
For L bushing
± 10 %
FR 50 mm, plain = AL
D = DBAN
M = Panel
±5%
L and F
L = LPRP
sealed
laws =
For M bushing
B = DBAN
M10 x 0.75
FD = 13 mm, slotted = AC from 100 
and LPRP
to 2.2 M
FJ = 22 mm, slotted = AM
FP = 47 mm, plain = AL
For M bushing
E = Peg
A = Peg
and DBAN
L=
M10 x 0.75
0 = none
A
B
TAPER
PACKAGING
A = Linear
L = Clockwise
logarithmic
F = Clockwise
inverse
logarithmic
B = Box of
10 pieces
SPECIAL
NUMBER
(if applicable)
Given by
Vishay
for custom
design
or
E105
CV1M
PART NUMBER DESCRIPTION (for information only)
PE30
LPRP
AC
200K
20 %
A
DBAN
CV1M
BO
MODEL FEATURES OPTION SHAFT VALUE TOL. TAPER OPTION SPECIAL DETENT PACKAGING
e3
CUSTOM
LEAD
SPECIAL
(Pb)-FREE
SHAFT
www.vishay.com
Document Number: 51037
For technical questions, contact: [email protected]
Revision: 29-Aug-12
See also Application Note: www.vishay.com/doc?51001 and www.vishay.com/doc?52029
135
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000