AVAGO AFCT

AFCT-5710Z and AFCT-5715Z
Families of Single-Mode Small Form Factor Pluggable (SFP)
Optical Transceivers with Optional DMI for Gigabit Ethernet (1.25 GBd)
Data Sheet
Description
Features
The AFCT-571xZ family of Small Form Factor Pluggable
(SFP) LC optical transceivers offers a wide range of
design options, including optional DMI features (further
described later), two temperature ranges (extended or
industrial), and choice of standard or bail delatch. The
AFCT-5715Z family targets applications requiring DMI,
while the AFCT-5710Z family is streamlined for those
applications where DMI is not needed. Throughout this
datasheet, AFCT-571xZ will refer to the entire product
family encompassing this full range of product options.
• ROHS-6 Compliant
• Optional Digital Diagnostic Monitoring available
- AFCT-5710Z family: without DMI
- AFCT-5715Z family: with DMI
• Per SFF-8472, diagnostic features on AFCT-5715Z
family enable Diagnostic Monitoring Interface for
optical transceivers with real-time monitoring of:
- Transmitted optical power
- Received optical power
- Laser bias current
- Temperature
- Supply voltage
• Compliant to IEEE 802.3Z Gigabit Ethernet (1.25 GBd)
1000BASE-LX & Small Form Factor Pluggable (SFP)
Multi-Source Agreement (MSA)
• Manufactured in an ISO 9001 compliant facility
• Hot-pluggable
• Temperature options
(Extended) -10°C to +85°C
(Industrial) -40°C to +85°C
• +3.3 V dc power supply
• 1310 nm longwave laser
• Eye safety certified:
- US 21 CFR(J)
- IEC 60825-1 (+All)
• LC-Duplex fiber connector compatible
• Link Lengths at 1.25 GBd:
- 0.5 to 550 m - 50 μm MMF
- 0.5 to 550 m - 62.5 μm MMF
- 0.5 m to 10 km - SMF
Part Number Options
The AFCT-571xZ SFP family consists of the following
products:
Part Number
DMI
Temperature
Latch Design
AFCT-5710LZ
AFCT-5710PZ
AFCT-5710ALZ
AFCT-5710APZ
AFCT-5715LZ
AFCT-5715PZ
AFCT-5715ALZ
AFCT-5715APZ
No
No
No
No
Yes
Yes
Yes
Yes
Extended
Extended
Industrial
Industrial
Extended
Extended
Industrial
Industrial
Standard
Bail
Standard
Bail
Standard
Bail
Standard
Bail
* Extended Temperature Range is -10 to 85 degrees C
Industrial Temperature Range is -40 to 85 degrees C
Related Products
• AFBR-5705Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fiber Channel with DMI
• AFBR-5701Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fiber Channel without
DMI
• AFCT-5715Z SFP family: 1.25GBd Ethernet
(1000BASE-LX) with DMI
• AFCT-5710Z SFP family: 1.25GBd Ethernet
(1000BASE-LX) without DMI
Applications
•
•
•
•
Ethernet Switch
Enterprise Router
Broadband aggregation and wireless infrastructure
Metro Ethernet multi-service access & provisioning
platforms
Overview
SFP MSA Compliance
The AFCT-571xZ family is compliant with both IEEE
802.3Z (1000BASE-LX) and the SFP Multi-Source
Agreement (MSA) specification. These transceivers
are intended for premise, public and access networking applications. They are qualified in accordance with
GR-468-CORE, and transmit data over single-mode
(SM) fiber for a link distance of 10 km, in excess of the
standard.
The product package is compliant with the SFP MSA with
the LC connector option. The SFP MSA includes specifications for mechanical packaging and performance as well
as dc, ac and control signal timing and performance.
The AFCT-5715Z family of optical transceivers adds
digital diagnostic monitoring to standard SFP functionality, enabling fault isolation, components monitoring
and failure prediction capabilities.
General Features
The AFCT-571xZ is compliant to 1 GbE specifications.
This includes specifications for the signal coding, optical
fiber and connector types, optical and electrical transmitter characteristics, optical and electrical receiver
characteristics, jitter characteristics, and compliance
testing methodology for the aforementioned.
This transceiver is capable of implementing both Single
Mode (SM) and Multimode (MM) optical fiber applications in that order of precedence in the event of conflicting specifications. In addition, the SM link type
exceeds the 2 m to 5 km 1000BASE-LX specification by
achieving compliance over 2 m to 10 km. The MM link
type is expected to meet the 62.5 μm MMF specification
when used with an “offset launch” fiber.
Optical Interface
The power supply is 3.3 V dc.
The High Speed I/O (HSIO) signal interface is a Low
Voltage Differential type. It is ac coupled and terminated
internally to the module. The internal termination is a
100 Ohm differential load.
Installation
The AFCT-571xZ can be installed in or removed from
any MSA-compliant Pluggable Small Form Factor (SFP)
port regardless of whether the host equipment is
operating or not. The module is simply inserted, electrical-interface first, under finger-pressure. Controlled hotplugging is ensured by 3-stage pin sequencing at the
electrical interface. This printed circuit board card-edge
connector is depicted in Figure 2.
As the module is inserted, first contact is made by
the housing ground shield, discharging any potentially component-damaging static electricity. Ground
pins engage next and are followed by Tx and Rx
power supplies. Finally, signal lines are connected. Pin
functions and sequencing are listed in Table 2.
Electrical Interface
Receiver
Photo-Detector
Light from Fiber
Amplification
&
Quantization
RD+ (Receive Data)
RD- (Receive Data)
Rx Loss Of Signal
MOD-DEF2 (SDA)
text
Controller & Memory
MOD-DEF1 (SCL)
MOD-DEF0
Transmitter
Light to Fiber
Laser
TX_DISABLE
Laser Driver &
Safety Circuit
TD+ (Transmit Data)
TD- (Transmit Data)
TX_FAULT
Figure 1. Transceiver Functional Diagram
2
321
20
VEET
19
1
VEET
TD–
2
TX FAULT
18
TD+
3
TX DISABLE
17
VEET
4
MOD-DEF(2)
16
VCCT
5
MOD-DEF(1)
15
VCCR
6
MOD-DEF(0)
14
VEER
7
RATE SELECT
13
RD+
8
LOS
12
RD–
9
VEER
11
VEER
10
VEER
TOP OF BOARD
Transmitter Section
321
ENGAGEMENT
SEQUENCE
The transmitter section includes a 1310 nm Fabry-Perot
laser and a transmitter driver circuit. The driver circuit
maintains a constant optical power level provided that
the data pattern is valid 8B/10B code. Connection to the
transmitter is provided via a LC optical connector.
The transmitter has full IEC 60825 and CDRH Class 1 eye
safety.
TX_DISABLE
The transmitter output can be disabled by asserting pin
3, TX_DISABLE. A high signal asserts this function while
a low signal allows normal laser operation. In addition,
via the 2-wire serial interface the transmitter output can
be disabled (address A2h, byte 110, bit 6) or monitored
(address A2h, byte 110, bit 7). The contents of A2h, byte
110, bit 6 are logic OR’d with hardware Tx_Disable (pin
3) to control transmitter operation. In the event of a
transceiver fault, such as the activation of the eye safety
circuit, toggling of the TX_DISABLE will reset the transmitter, as depicted in Figure 4.
BOTTOM OF BOARD
(AS VIEWED THROUGH TOP OF BOARD)
Figure 2. Pin description of the SFP electrical interface.
1 µH
3.3 V
10 µF
0.1 µF
1 µH
3.3 V
VCC,T
SFP MODULE
0.1 µF
4.7 K to 10 KΩ
4.7 K to 10 KΩ
Tx_DISABLE
Tx_FAULT
Tx_FAULT
VREFR
VREFR
SO+
50 Ω
TD+
SO–
50 Ω
TD–
TX GND
TX[0:9]
TBC
EWRAP
PROTOCOL
IC
RBC
Rx_RATE
TBC
EWRAP
10 µF
RBC
Rx_RATE
REFCLK
SI+
100 Ω
SI–
RD+
50 Ω
RD–
Rx_LOS
RX GND
MOD_DEF2
MOD_DEF1
MOD_DEF0
GPIO(X)
GPIO(X)
GP14
106.25 MHz
Figure 3. Typical Application Configuration
3
4.7 K to
10 KΩ
0.01 µF
4.7 K to
10 KΩ
VCC,R
50 Ω
0.1
µF
50 Ω
Rx_LOS
REFCLK
LASER DRIVER
& SAFETY
CIRCUITRY
100 Ω
VCC,R
4.7 K to 10 KΩ
RX[0:9]
0.01 µF
4.7 K to
10 KΩ
3.3 V
0.01 µF
0.01 µF
AMPLIFICATION
&
QUANTIZATION
50 Ω
VCC,R
EEPROM
TX_FAULT
Functional Data I/O
A laser fault or a low VCC condition will activate the
transmitter fault signal, TX_FAULT, and disable the laser.
This signal is an open collector output (pull-up required
on the host board); A low signal indicates normal laser
operation and a high signal indicates a fault. The TX_
FAULT will be latched high when a laser fault occurs and
is cleared by toggling the TX_DISABLE input or power
cycling the transceiver. The TX_FAULT is not latched
for Low VCC. The transmitter fault condition can also
be monitored via the two-wire serial interface (address
A2h, byte 110, bit 2).
Avago’s AFCT-571xZ transceiver is designed to accept
industry standard differential signals. The transceiver
provides an AC-coupled, internally terminated data
interface. Bias resistors and coupling capacitors have
been included within the module to reduce the number
of components required on the customer’s board.
Figure 2 illustrates the recommended interface circuit.
Eye Safety Circuit
Under normal operating conditions, the laser power
will be maintained below the eye-safety limit. If the
eye safety limit is exceeded at any time, a laser fault will
occur and the TX_FAULT output will be activated.
Receiver Section
The receiver section for the AFCT-571xZ contains an
InGaAs/InP photo detector and a preamplifier mounted
in an optical subassembly. This optical subassembly is
coupled to a post amplifier/decision circuit on a circuit
board. The design of the optical subassembly provides
better than 12 dB Optical Return Loss (ORL).
Connection to the receiver is provided via a LC optical
connector.
RX_LOS
The receiver section contains a loss of signal (RX_LOS)
circuit to indicate when the optical input signal power
is insufficient for Gigabit Ethernet compliance. A high
signal indicates loss of modulated signal, indicating link
failure such as a broken fiber or a failed transmitter. RX_
LOS can be also be monitored via the two-wire serial
(address A2h, byte 110, bit 1).
VCCT
0.1 µF
1 µH
VCCR
3.3 V
10 µF
The AFCT-571xZ family complies with the SFF-8074i
specification, which defines the module’s serial identification protocol to use the 2-wire serial CMOS EEPROM
protocol of the ATMEL AT24C01A or similar. Standard
SFP EEPROM bytes 0-255 are addressed per SFF-8074i at
memory address 0xA0 (A0h).
As an enhancement to the conventional SFP interface
defined in SFF-8074i, the AFCT-5715Z is also compliant
to SFF-8472 (the digital diagnostic interface for SFP).
This enhancement adds digital diagnostic monitoring
to standard SFP functionality, enabling failure prediction, fault isolation, and component monitoring capabilities.
Using the 2-wire serial interface, the AFCT-5715Z
provides real time access to transceiver internal supply
voltage and temperature, transmitter output power,
laser bias current and receiver average input power,
allowing a host to predict system compliance issues.
These five parameters are internally calibrated, per the
MSA. New digital diagnostic information is accessed
per SFF-8472 using EEPROM bytes 0-255 at memory
address 0xA2 (A2h).
The digital diagnostic interface also adds the ability to
disable the transmitter (TX_DISABLE), monitor for Transmitter Faults (TX_FAULT) and monitor for Receiver Loss
of Signal (RX_LOS).
Contents of the MSA-compliant serial ID memory are
shown in Tables 10 through 14. The SFF-8074i and
SFF-8472 specifications are available from the SFF
Committee at http://www.sffcommittee.org.
1 µH
0.1 µF
Digital Diagnostic Interface and Serial Identification
0.1 µF
10 µF
The I2C accessible memory page address 0xB0 is used
internally by SFP for the test and diagnostic purposes
and it is reserved.
Predictive Failure Identification
SFP MODULE
HOST BOARD
Figure 4. MSA required power supply filter
4
The diagnostic information allows the host system
to identify potential link problems. Once identified, a
fail-over technique can be used to isolate and replace
suspect devices before system uptime is impacted.
Compliance Prediction
Operating Temperature
The real-time diagnostic parameters can be monitored
to alert the system when operating limits are exceeded
and compliance cannot be ensured.
The AFCT-571xZ family is available in either Extended
(-10 to +85°C) or Industrial (-40 to +85°C) temperature
ranges.
Fault Isolation
Power Supply Noise
The diagnostic information can allow the host to
pinpoint the location of a link problem and accelerate
system servicing and minimize downtime.
The AFCT-571xZ can withstand an injection of PSN on
the VCC lines of 100 mV ac with a degradation in eye
mask margin of up to 10% on the transmitter and a 1
dB sensitivity penalty on the receiver. This occurs when
the product is used in conjunction with the MSA recommended power supply filter shown in Figure 3.
Component Monitoring
As part of the host system monitoring, the real time
diagnostic information can be combined with system
level monitoring to ensure system reliability.
Application Support
An Evaluation Kit and Reference Designs are available
to assist in evaluation of the AFCT-571xZ SFPs. Please
contact your local Field Sales representative for availability and ordering details.
Regulatory Compliance
The transceiver regulatory compliance is provided in
Table 1 as a figure of merit to assist the designer. The
overall equipment design will determine the certification level.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (>2000 Volts)
Electrostatic Discharge (ESD)
to the Duplex LC Receptacle
Bellcore GR1089-CORE
25 kV Air Discharge
Electromagnetic Interference
(EMI)
FCC Class B
Applications with high SFP port counts are expected to be compliant; however, margins are dependent on customer board and chassis design.
Immunity
Variation of IEC 61000-4-3
No measurable effect from a 10 V/m field swept
from 80 to 1000 MHz applied to the transceiver
without a chassis enclosure.
Eye Safety
US FDA CDRH AEL Class 1
EN (IEC) 60825-1, 2,
EN60950 Class 1
CDRH certification # 9521220-132
TUV file R72102126.01
Component Recognition
Underwriter’s Laboratories and
Canadian Standards Association Joint
Component Recognition for Information Technology Equipment Including
Electrical Business Equipment
UL file # E173874
ROHS Compliance
5
10 Zaps at 8 kV (contact discharge) on the electrical faceplate on panel.
Less than 1000ppm of: cadmium, lead, mercury,
hexavalent chromium, polybrominated biphenyls,
and polybrominated biphenyl ethers
Electrostatic Discharge (ESD)
Eye Safety
There are two conditions in which immunity to ESD
damage is important:
The AFCT-571xZ transceivers provide Class 1 eye
safety by design. Avago Technologies has tested the
transceiver design for regulatory compliance, under
normal operating conditions and under a single fault
condition. See Table 1.
The first condition is static discharge to the transceiver
during handling such as when the transceiver is inserted
into the transceiver port. To protect the transceiver,
it is important to use normal ESD handling precautions including the use of grounded wrist straps, work
benches, and floor mats in ESD controlled areas. The ESD
sensitivity of the AFCT-571xZ is compatible with typical
industry production environments.
The second condition is static discharge to the exterior
of the host equipment chassis after installation. To the
extent that the duplex LC optical interface is exposed
to the outside of the host equipment chassis, it may be
subject to system-level ESD requirements. The ESD performance of the AFCT-571xZ exceeds typical industry
standards. Table 1 documents ESD immunity to both of
these conditions.
Electromagnetic Interference (EMI)
Most equipment designs using the AFCT-571xZ SFPs
are subject to the requirements of the FCC in the
United States, CENELEC EN55022 (CISPR 22) in Europe
and VCCI in Japan. The metal housing and shielded
design of the transceiver minimize EMI and provide
excellent EMI performance.
EMI Immunity
The AFCT-571xZ transceivers have a shielded design
to provide excellent immunity to radio frequency
electromagnetic fields which may be present in some
operating environments.
6
Flammability
The AFCT-571xZ family of SFPs is compliant to UL
94V-0.
Customer Manufacturing Processes
This module is pluggable and is not designed for
aqueous wash, IR reflow, or wave soldering processes.
Caution
The AFCT-571xZ contains no user-serviceable parts.
Tampering with or modifying the performance of the
AFCT-571xZ will result in voided product warranty. It
may also result in improper operation of the transceiver
circuitry, and possible over-stress of the laser source.
Device degradation or product failure may result.
Connection of the AFCT-571xZ to a non-approved
optical source, operating above the recommended
absolute maximum conditions may be considered an
act of modifying or manufacturing a laser product. The
person(s) performing such an act is required by law to
re-certify and re-identify the laser product under the
provisions of U.S. 21 CF.
Table 2. Pin description
Pin
Name
Function/Description
Engagement
Order(insertion)
1
VeeT
Transmitter Ground
1
2
TX Fault
Transmitter Fault Indication
3
1
3
TX Disable
Transmitter Disable - Module disables on high or open
3
2
4
MOD-DEF2
Module Definition 2 - Two wire serial ID interface
3
3
5
MOD-DEF1
Module Definition 1 - Two wire serial ID interface
3
3
6
MOD-DEF0
Module Definition 0 - Grounded in module
3
3
7
Rate Selection
Not Connected
3
8
LOS
Loss of Signal
3
9
VeeR
Receiver Ground
1
10
VeeR
Receiver Ground
1
11
VeeR
Receiver Ground
1
12
RD-
Inverse Received Data Out
3
5
13
RD+
Received Data Out
3
5
14
VeeR
Reciver Ground
1
15
VccR
Receiver Power -3.3 V ±5%
2
6
16
VccT
Transmitter Power -3.3 V ±5%
2
6
17
VeeT
Transmitter Ground
1
18
TD+
Transmitter Data In
3
7
19
TD-
Inverse Transmitter Data In
3
7
20
VeeT
Transmitter Ground
1
Notes
4
Notes:
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7KΩ – 10 KΩ resistor on the host board to a supply
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the
output will be pulled to < 0.8 V.
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 KΩ resistor.
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V): Undefined
High (2.0 – 3.465 V): Transmitter Disabled
Open: Transmitter Disabled
3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 KΩ resistor on the host board to a supply less
than VccT +0.3 V or VccR+0.3 V.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 KΩ – 10 KΩ resistor on the host board
to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined
by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+: These are the differential receiver outputs. They are AC coupled 100 Ω differential lines which should be terminated with 100 Ω
differential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on
these lines must be between 370 and 2000 mV differential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv
differential.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.135 – 3.465 V at the SFP connector pin. The in-rush
current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
7. TD-/+: These are the differential transmitter inputs. They are AC coupled differential lines with 100 Ω differential termination inside the
module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of
500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended differential voltage swing is found in Table 5.
7
Table 3. Absolute Maximum Ratings
Absolute maximum ratings are those values beyond which functional performance is not intended, device reliability is not implied, and damage to the device may occur.
Parameter
Symbol
Minimum
Maximum
Unit
Storage Temperature (non-operating)
TS
-40
+100
°C
Relative Humidity
RH
5
95
%
Case Temperature
TC
-40
85
°C
Supply Voltage
VCC
-0.5
3.8
V
Control Input Voltage
VI
-0.5
VCC+0.5
V
Notes
1
Table 4. Recommended Operating Conditions
Typical operating conditions are those values for which functional performance and device reliability is implied.
Parameter
Symbol
Minimum
Case Operating Temperature
AFCT-5710LZ/PZ & AFCT-5715LZ/PZ
AFCT-5710ALZ/APZ & AFCT-5715ALZ/APZ
TC
TC
-10
-40
Supply Voltage
VCC
3.14
Typical
3.3
Maximum
Unit
+85
+85
°C
°C
3.47
V
Notes
Table 5. Transceiver Electrical Characteristics
Parameter
Symbol
Module supply current
Power Dissipation
Minimum
Typical
Maximum
Unit
Notes
ICC
200
240
mA
2
PDISS
660
830
mW
2
PSNR
100
mV
3
AC Electrical Characteristics
Power Supply Noise Rejection (peak - peak)
Inrush Current
30
mA
VccT, R+0.3
V
0.8
V
Vcc
V
0.8
V
DC Electrical Characteristics
Sense Outputs:
Transmit Fault (TX_FAULT)
Loss of Signal (LOS) MOD-DEF2
Control Inputs:
Transmitter Disable (TX_DISABLE)
MOD-DEF1, 2
VOH
2.0
VOL
VIH
2.0
VIL
4
4,5
Data Input:
Transmitter Differential Input Voltage (TD+/-)
VI
500
2400
mV
6
Data Ouput:
Receiver Differential Output Voltage (RD+/-)
VO
370
1600
mV
7
Receiver Data Rise and Fall Times
Trf
400
ps
Receiver Contributed Total Jitter
TJ
0.33267
UIps
Notes:
1 The module supply voltages, VccT and VccR, must not differ by more than 0.5V or damage to the device may occur.
2. Over temperature and Beginning of Life.
3. MSA filter is required on host board 10 Hz to 1 MHz. See Figure 3
4. LVTTL, External 4.7 - 10 KΩ Pull-Up Resistor required
5. LVTTL, Internal 4.7 - 10 KΩ Pull-Up Resistor required for TX_Disable
6. Internally ac coupled and terminated (100 Ohm differential)
7. Internally ac coupled and load termination located at the user SerDes
8. Per IEEE 802.3
8
8
Table 6. Transmitter Optical Characteristics
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Notes
Average Optical Output Power
POUT
-9.5
Optical Extinction Ratio
ER
9
-3
dBm
Note 1
TX Optical Eye Mask Margin
MM
0
Center Wavelength
λC
1270
Spectral Width - rms
σ, rms
Optical Rise/Fall Time
tr, tf
260
ps
Relative Intensity Noise
RIN
-120
dB/Hz
Contributed Total Jitter (Transmitter)
1.25 Gb/s
TJ
0.284
227
UI
ps
POUT TX_DISABLE Asserted
POFF
dB
30
%
1355
Note 3
nm
nm
-45
20-80%
Note 2
dBm
Notes:
1. Class 1 Laser Safety per FDA/CDRH
2. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1x10-12 BER by
multiplying the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the
actual contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component
output DJ and TJ remain within their specified FC-PI maximum limits with the worst case specified component jitter input.
3. Eye shall be measured with respect to the mask of the eye using filter defined in IEEE 802.3 section 38.6.5
Table 7. Receiver Optical Characteristics
Parameter
Symbol
Input Optical Power
Receiver Sensitivity
Minimum
Typical
Maximum
Unit
PIN
-3
dBm
PMIN
-19
dBm
Stressed Receiver Sensitivity
(Optical Average Input Power)
-14.4
dBm
Receiver Electrical 3 dBUpper
Cutoff Frequency
1500
MHz
1355
nm
Operating Center Wavelength
ΛC
Return Loss (minimum)
Loss of Signal - Assert
PA
Loss of Signal - De-Assert
PD
Loss of Signal - Hysteresis
PD - PA
1270
Notes
1, 2
12
dB
-30
dBm
3
dBm
3
-20
0.5
dB
Notes:
1. BER = 10-12
2. An average power of -20 dBm with an Extinction Ratio of 9 dB is approximately equivalent to an OMA of 15 μW.
3. These average power values are specified with an Extinction Ratio of 9 dB. The loss-of-signal circuitry responds to valid 8B/10B-encoded peak
to peak input optical power, not average power.
9
Table 8. Transceiver Timing Characteristics
Parameter
Symbol
Hardware TX_DISABLE Assert Time
Minimum
Maximum
Unit
Notes
t_off
10
μs
Note 1
Hardware TX_DISABLE Negate Time
t_on
1
ms
Note 2
Time to initialize, including reset of TX_FAULT
t_init
300
ms
Note 3
Hardware TX_FAULT Assert Time
t_fault
100
μs
Note 4
Hardware TX_DISABLE to Reset
t_reset
μs
Note 5
Hardware RX_LOS Assert Time
t_loss_on
100
μs
Note 6
Hardware RX_LOS De-Assert Time
t_loss_off
100
μs
Note 7
Software TX_DISABLE Assert Time
t_off_soft
100
ms
Note 8
Software TX_DISABLE Negate Time
t_on_soft
100
ms
Note 9
Software Tx_FAULT Assert Time
t_fault_soft
100
ms
Note 10
Software Rx_LOS Assert Time
t_loss_on_soft
100
ms
Note 11
Software Rx_LOS De-Assert Time
t_loss_off_soft
100
ms
Note 12
Analog parameter data ready
t_data
1000
ms
Note 13
Serial bus hardware ready
t_serial
300
ms
Note 14
Write Cycle Time
t_write
10
ms
Note 15
Serial ID Clock Rate
f_serial_clock
400
kHz
10
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of
nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
Parameter
Symbol
Min
Units
Notes
Transceiver Internal Temperature Accuracy
TINT
± 3.0
°C
Valid from TC = -40 °C to +85 °C
Transceiver Internal Supply Voltage Accuracy
VINT
± 0.1
V
Valid over VCC = 3.3 V ± 5%
Transmitter Laser DC Bias Current Accuracy
IINT
± 10
%
Percentage of nominal bias value
Transmitted Average Optical Output Power Accuracy
PT
± 3.0
dB
Valid from 100 μW to 500μW, avg
Received Average Optical Input Power Accuracy
PR
± 3.0
dB
Valid from 10 μW to 500μW avg
10
VCC > 2.97 V
VCC > 2.97 V
Tx_FAULT
Tx_FAULT
Tx_DISABLE
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_init
t_init
t-init: TX DISABLE NEGATED
t-init: TX DISABLE ASSERTED
VCC > 2.97 V
Tx_FAULT
Tx_FAULT
Tx_DISABLE
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_off
t_on
t_init
INSERTION
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
OCCURANCE OF FAULT
OCCURANCE OF FAULT
Tx_FAULT
Tx_FAULT
Tx_DISABLE
Tx_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_reset
t_fault
* CANNOT READ INPUT...
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
t_init*
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
OCCURANCE OF FAULT
Tx_FAULT
LOS
TRANSMITTED SIGNAL
t_fault
t_loss_on
t_reset
* SFP SHALL CLEAR Tx_FAULT IN
t_init IF THE FAILURE IS TRANSIENT
t_init*
t-fault: TX DISABLE ASSERTED THEN NEGATED,
TX SIGNAL NOT RECOVERED
Figure 5. Transceiver Timing Diagrams (Module Installed Except Where Noted)
11
OCCURANCE
OF LOSS
OPTICAL SIGNAL
Tx_DISABLE
t-loss-on & t-loss-off
t_loss_off
Table 10. EEPROM Serial ID Memory Contents - Page A0h
Byte #
Decimal
Data
Hex
Notes
Byte #
Decimal
Data
Hex
0
03
SFP physical device
37
00
Hex Byte of Vendor OUI (note 3)
1
04
SFP function defined by serial ID only
38
17
Hex Byte of Vendor OUI (note 3)
2
07
LC optical connector
39
6A
Hex Byte of Vendor OUI (note 3)
3
00
40
41
“A” - Vendor Part Number ASCII character
4
00
41
46
“F” - Vendor Part Number ASCII character
5
00
6
02
7
8
Notes
42
43
“C” - Vendor Part Number ASCII character
43
54
“T” - Vendor Part Number ASCII character
00
44
2D
“-” - Vendor Part Number ASCII character
00
45
35
“5” - Vendor Part Number ASCII character
1000BASE-LX
9
00
46
37
“7” - Vendor Part Number ASCII character
10
00
47
31
“1” - Vendor Part Number ASCII character
11
01
Compatible with 8B/10B encoded data
12
0C
1200 MBit/sec nominal bit rate
49
Note 4
13
00
50
Note 4
14
0A
51
Note 4
15
64
52
20
“ “ - Vendor Part Number ASCII character
16
37
Note 1
53
20
“ “ - Vendor Part Number ASCII character
17
37
Note 2
54
20
“ “ - Vendor Part Number ASCII character
18
00
55
20
“ “ - Vendor Part Number ASCII character
19
00
56
20
“ “ - Vendor Revision Number ASCII character
20
41
“A” - Vendor Name ASCII character
57
20
“ “ - Vendor Revision Number ASCII character
21
56
“V” - Vendor Name ASCII character
58
20
“ “ - Vendor Revision Number ASCII character
22
41
“A” - Vendor Name ASCII character
59
20
“ “ - Vendor Revision Number ASCII character
23
47
“G” - Vendor Name ASCII character
60
05
Hex Byte of Laser Wavelength (Note 5)
24
4F
“O” - Vendor Name ASCII character
61
1E
Hex Byte of Laser Wavelength (Note 5)
25
20
“ “ - Vendor Name ASCII character
62
00
48
26
20
“ “ - Vendor Name ASCII character
63
27
20
“ “ - Vendor Name ASCII character
64
Note 4
Checksum for Bytes 0-62 (Note 6)
00
28
20
“ “ - Vendor Name ASCII character
65
1A
29
20
“ “ - Vendor Name ASCII character
66
00
30
20
“ “ - Vendor Name ASCII character
67
00
31
20
“ “ - Vendor Name ASCII character
68-83
Vendor Serial Number ASCII characters (Note7)
32
20
“ “ - Vendor Name ASCII character
84-91
Vendor Date Code ASCII characters (Note 8)
33
20
“ “ - Vendor Name ASCII character
92
Note 4
34
20
“ “ - Vendor Name ASCII character
93
Note 4
35
20
“ “ - Vendor Name ASCII character
94
Note 4
36
00
95
96 - 255
Hardware SFP TX_DISABLE, TX_FAULT & RX_LOS
Checksum for Bytes 64-94 (Note 6)
00
Notes:
1. Link distance with 50/125 μm cable.
2. Link distance with 62.5/125 μm.
3. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes hex).
4. See Table 11 on following page for part number extensions and data-fields.
5. Laser wavelength is represented in 16 unsigned bits. The hex representation of 1310 (nm) is 051E.
6. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
7. Addresses 68-83 specify the ASCII serial number and will vary on a per unit basis.
8. Addresses 84-91 specify the ASCII date code and will vary on a per date code basis.
12
Table 11. Part Number Extensions and Datafields
AFCT-5710ALZ
AFCT-5710APZ
AFCT-5710LZ
AFCT-5710PZ
Address
Hex
ASCII
Address
Hex
ASCII
Address
Hex
ASCII
Address
Hex
ASCII
48
30
0
48
30
0
48
30
0
48
30
0
49
41
A
49
41
A
49
4C
L
49
50
P
50
4C
L
50
50
P
50
5A
Z
50
5A
Z
51
5A
Z
51
5A
Z
51
20
51
20
92
0
92
0
92
0
92
0
93
0
93
0
93
0
93
0
94
0
94
0
94
0
94
0
AFCT-5715ALZ
Address
13
Hex
AFCT-5715APZ
ASCII
Address
Hex
AFCT-5715LZ
ASCII
Address
Hex
AFCT-5715PZ
ASCII
Address
Hex
ASCII
48
35
5
48
35
5
48
35
5
48
35
5
49
41
A
49
41
A
49
4C
L
49
50
P
50
4C
L
50
50
P
50
5A
Z
50
5A
Z
51
5A
Z
51
5A
Z
51
20
51
20
92
68
92
68
92
68
92
68
93
F0
93
F0
93
F0
93
F0
94
1
94
1
94
1
94
1
Table 12. EEPROM Serial ID Memory Contents - Address A2h (AFCT-5715Z family only)
Byte #
Decimal
Notes
Byte #
Decimal
Notes
Byte #
Decimal
Notes
0
Temp H Alarm MSB1
26
Tx Pwr L Alarm MSB4
104
Real Time Rx PAV MSB5
1
Temp H Alarm LSB1
27
Tx Pwr L Alarm LSB4
105
Real Time Rx PAV LSB5
2
Temp L Alarm MSB1
28
Tx Pwr H Warning MSB4
106
Reserved
3
Temp L Alarm LSB1
29
Tx Pwr H Warning LSB4
107
Reserved
4
Temp H Warning MSB1
30
Tx Pwr L Warning MSB4
108
Reserved
5
Temp H Warning LSB1
31
Tx Pwr L Warning LSB4
109
Reserved
6
Temp L Warning MSB1
32
Rx Pwr H Alarm MSB5
110
Status/Control - see Table 13
7
Temp L Warning LSB1
33
Rx Pwr H Alarm LSB5
111
Reserved
8
VCC
H Alarm MSB2
34
Rx Pwr L Alarm MSB5
112
Flag Bits - see Table 14
9
VCC
H Alarm LSB2
35
Rx Pwr L Alarm LSB5
113
Flag Bit - see Table 14
10
VCC L Alarm MSB2
36
Rx Pwr H Warning MSB5
114
Reserved
11
VCC L Alarm LSB2
37
Rx Pwr H Warning LSB5
115
Reserved
12
VCC H Warning MSB2
38
Rx Pwr L Warning MSB5
116
Flag Bits - see Table 14
13
VCC H Warning LSB2
39
Rx Pwr L Warning LSB5
117
Flag Bits - see Table 14
14
VCC L Warning MSB2
40-55
Reserved
118
Reserved
15
VCC L Warning LSB2
56-94
External Calibration Constants6
119
Reserved
16
Tx Bias H Alarm MSB3
95
Checksum for Bytes 0-947
120-122
Reserved
17
Tx Bias H Alarm LSB3
96
Real Time Temperature MSB1
123
18
Tx Bias L Alarm MSB3
97
Real Time Temperature LSB1
124
19
Tx Bias L Alarm LSB3
98
Real Time Vcc MSB2
125
20
Tx Bias H Warning MSB3
99
Real Time Vcc LSB2
126
21
Tx Bias H Warning LSB3
100
Real Time Tx Bias MSB3
127
Reserved8
22
Tx Bias L Warning MSB3
101
Real Time Tx Bias LSB3
128-247
Customer Writable9
23
Tx Bias L Warning LSB3
102
Real Time Tx Power MSB4
248-255
Vendor Specific
24
Tx Pwr H Alarm MSB4
103
Real Time Tx Power LSB4
25
Tx Pwr H Alarm LSB4
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C.
2. Supply voltage (VCC) is decoded as a 16 bit unsigned integer in increments of 100 μV.
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 μA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
6. Bytes 55-94 are not intended from use with AFCT-5715xxxx, but have been set to default values per SFF-8472.
7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
8. Byte 127 accepts a write but performs no action (reserved legacy byte).
9. Bytes 128-247 are write enabled (customer writable).
14
Table 13. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFCT-5715Z family only)
Bit #
Status/Control Name
Description
7
Tx Disable State
Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted)
6
Soft Tx Disable
Read/write bit for changing digital state of SFP Tx_Disable function1
5
Reserved
4
Rx Rate Select State
3
Reserved
2
Tx Fault State
Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted)
1
Rx LOS State
Digital state of the SFP LOS Output Pin (1 = LOS asserted)
0
Data Ready (Bar)
Indicates transceiver is powered and real time sense data is ready (0 = Ready)
Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit)2
Notes:
1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter.
2. AFCT-5715Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth.
Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117
(AFCT-5715Z family only)
Byte
112
113
116
117
15
Bit #
Flag Bit Name
Description
7
Temp High Alarm
Set when transceiver nternal temperature exceeds high alarm threshold.
6
Temp Low Alarm
Set when transceiver internal temperature exceeds alarm threshold.
5
VCC High Alarm
Set when transceiver internal supply voltage exceeds high alarm threshold.
4
VCC Low Alarm
Set when transceiver internal supply voltage exceeds low alarm threshold.
3
Tx Bias High Alarm
Set when transceiver laser bias current exceeds high alarm threshold.
2
Tx Bias Low Alarm
Set when transceiver laser bias current exceeds low alarm threshold.
1
Tx Power High Alarm
Set when transmitted average optical power exceeds high alarm threshold.
0
Tx Power Low Alarm
Set when transmitted average optical power exceeds low alarm threshold.
7
Rx Power High Alarm
Set when received P_Avg optical power exceeds high alarm threshold.
6
Rx Power Low Alarm
Set when received P_Avg optical power exceeds low alarm threshold.
0-5
Reserved
7
Temp High Warning
Set when transceiver internal temperature exceeds high warning threshold.
6
Temp Low Warning
Set when transceiver internal temperature exceeds low warning threshold.
5
VCC High Warning
Set when transceiver internal supply voltage exceeds high warning threshold.
4
VCC Low Warning
Set when transceiver internal supply voltage exceeds low warning threshold.
3
Tx Bias High Warning
Set when transceiver laser bias current exceeds high warning threshold.
2
Tx Bias Low Warning
Set when transceiver laser bias current exceeds low warning threshold.
1
Tx Power High Warning
Set when transmitted average optical power exceeds high warning threshold.
0
Tx Power Low Warning
Set when transmitted average optical power exceeds low warning threshold.
7
Rx Power High Warning
Set when received P_Avg optical power exceeds high warning threshold.
9
Rx Power Low Warning
Set when received P_Avg optical power exceeds low warning threshold.
0-5
Reserved
AFCT-571xZ
1300 nm LASER PROD
21CFR(J) CLASS 1
COUNTRY OF ORIGIN YYWW
XXXXXX
13.8±0.1
[0.541±0.004]
13.4±0.1
[0.528±0.004]
2.60
[0.10]
DEVICE SHOWN WITH
DUST CAP AND BAIL
WIRE DELATCH
55.2±0.2
[2.17±0.01]
FRONT EDGE OF SFP
TRANSCEIVER CAGE
6.25±0.05
[0.246±0.002]
13.0±0.2
[0.512±0.008]
TX
8.5±0.1
[0.335±0.004]
RX
AREA
FOR
PROCESS
PLUG
6.6
[0.261]
13.50
[0.53]
14.8 MAX. UNCOMPRESSED
[0.583]
ST ANDARD DELATCH
12.1±0.2
[0.48±0.01]
Figure 6. Drawing of SFP Transceiver
16
0.7MAX. UNCOMPRESSED
[0.028]
DIMENSIONS ARE IN MILLIMETERS (INCHES)
X
Y
34.5
10x ∅1.05 ±0.01
∅ 0.1 L X A S
1
16.25
MIN.PITCH
7.1
∅ 0.85 ±0.05
∅ 0.1 S X Y
2.5
2.5
B
PCB
EDGE
8.58
16.25 14.2511.08
REF.
10
3x
7.2
A
1
3.68
5.68
20
PIN 1
2x 1.7
8.48
9.6
4.8
11
10
2.0
11x
11x 2.0
5
26.8
10
3x
3
11.93
SEE DET AIL 1
9x 0.95 ±0.05
∅ 0.1 L X A S
2
41.3
42.3
3.2
5
0.9
PIN 1
9.6
20x 0.5 ±0.03
0.06 L A S B S
LEGEND
20
10.53
10.93
0.8
TYP.
10
11.93
2. THROUGH HOLES, PLATING OPTIONAL
11
3. HATCHED AREA DENO TES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4
2x 1.55 ±0.05
∅ 0.1 L A S B S
DETAIL 1
Figure 7. SFP host board mechanical layout
17
1. PADS AND VIAS ARE CHASSIS GROUND
2 ±0.005 TYP.
0.06 L A S B S
4. AREA DENOTES COMPONENT
KEEPOUT (TRA CES ALLO WED)
DIMENSIONS ARE IN MILLIMETERS
1.7±0.9
3.5±0.3
[.07±.04]
[.14±.01]
41.73±0.5
PCB
[1.64±.02]
BEZEL
AREA
FOR
PROCESS
PLUG
15MAX
[.59]
Tcase REFERENCE POINT
CAGE
ASSEMBLY
15.25±0.1
[.60±0.004]
10.4±0.1
[.41±0.004]
12.4REF
[.49]
9.8MAX
[.39]
1.15REF
[.05]
BELOW PCB
10REF
[.39]
TO PCB
0.4±0.1
[.02±0.004]
BELOW PCB
16.25±0.1MIN PITCH
[.64±0.004]
MSA-SPECIFIED BEZEL
DIMENSIONS ARE IN MILLIMETERS [INCHES].
Figure 8. Assembly Drawing
18
Ordering Information
Please contact your local field sales engineer or one of
Avago Technologies franchised distributors for ordering
information. For technical information, please visit
Avago Technologies’ web-page at www.avagotech.com or
contact one of Avago Technologies’ regional Technical
Response Centers.
For information related to SFF Committee documentation visit www.sffcommittee.org.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes AV01-0167EN
AV02-2366EN - September 12, 2012