MAXIM MAX2607EUT

EVALUATION KIT AVAILABLE
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
LE
AVAILAB
General Description
Features
The MAX2605–MAX2609 are compact, high-performance
intermediate-frequency (IF) voltage-controlled oscillators
(VCOs) designed specifically for demanding portable
wireless communication systems. They combine monolithic construction with low-noise, low-power operation in a
tiny 6-pin SOT23 package.
♦ Small Size
These low-noise VCOs feature an on-chip varactor and
feedback capacitors that eliminate the need for external
tuning elements, making the MAX2605–MAX2609 ideal
for portable systems. Only an external inductor is
required to set the oscillation frequency. In addition, an
integrated differential output buffer is provided for driving a mixer or prescaler. The buffer output is capable
of supplying up to -8dBm (differential) with a simple
power match. It also provides isolation from load
impedance variations.
The MAX2605–MAX2609 operate from a single +2.7V to
+5.5V supply and offer low current consumption. These IF
oscillators can cover the 45MHz to 650MHz frequency
range.
♦ Differential or Single-Ended Outputs
Applications
Cellular and PCS Mobile Phones
♦ Integrated Varactor for Tuning
♦ Low Phase Noise
♦ Wide Application Frequency Range
♦ Single +2.7V to +5.5V Supply
♦ Ultra-Small SOT23-6 Package
♦ On-Chip Temperature-Stable Bias
♦ Low-Current Operation
Ordering Information
PART
TEMP. RANGE
PINPACKAGE
TOP
MARK
MAX2605EUT-T
-40°C to +85°C
6 SOT23-6
AABB
MAX2606EUT-T
-40°C to +85°C
6 SOT23-6
AABC
MAX2607EUT-T
-40°C to +85°C
6 SOT23-6
AABD
2.4GHz ISM Band
MAX2608EUT-T
-40°C to +85°C
6 SOT23-6
AABE
902MHz to 928MHz ISM Band
MAX2609EUT-T
-40°C to +85°C
6 SOT23-6
AABF
Land Mobile Radio
GPS Receivers
Functional Diagrams
General-Purpose IF Oscillators
Pin Configuration/
Functional Diagram
Selector Guide
FREQUENCY
RANGE
(MHz)
SUPPLY
CURRENT
(mA)
PHASE
NOISE
(dBc/Hz)
MAX2605
45 to 70
1.9
-117
MAX2606
MAX2607
MAX2608
MAX2609
70 to 150
150 to 300
300 to 500
500 to 650
2.1
2.1
2.7
3.6
-112
-107
-100
-93
PART
TOP VIEW
IND 1
GND 2
MAX2605
MAX2606
MAX2607
MAX2608
MAX2609
TUNE 3
Pin Configurations appear at end of data sheet.
Functional Diagrams continued at end of data sheet.
UCSP is a trademark of Maxim Integrated Products, Inc.
6
OUT+
5
VCC
4
OUT-
SOT23-6
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-1673; Rev 0a; 4/02
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
ABSOLUTE MAXIMUM RATINGS
VCC to GND ..............................................................-0.3V to +6V
IND to GND ................................................-0.6V to (VCC + 0.3V)
TUNE to GND .............................................-0.3V to (VCC + 0.3V)
OUT+, OUT- to GND ..................................-0.3V to (VCC + 0.6V)
Continuous Power Dissipation (TA = +85°C)
6-Pin SOT23 (derate 8.7mW/°C above +70°C) ...........696mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +2.7V to +5.5V, VTUNE = 0.4V to 2.4V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +2.75V,
VTUNE = 1.5V, and TA = +25°C.) (Note1)
PARAMETER
CONDITIONS
Supply Voltage
MAX2606
MAX2607
MAX2608
MAX2609
DC Output Current (Note 3)
TUNE Input Current
2
TYP
MAX
1.9
2.6
2.7
MAX2605
Supply Current (Note 2)
MIN
OUT+ plus OUT-
TA = +25°C
5.5
TA = -40°C to +85°C
UNITS
V
2.8
TA = +25°C
2.1
2.7
2.1
3.2
TA = -40°C to +85°C
3.0
TA = +25°C
TA = -40°C to +85°C
3.5
TA = +25°C
2.7
4.4
3.6
6.8
1.0
1.5
TA = -40°C to +85°C
mA
5.5
TA = +25°C
TA = -40°C to +85°C
7.5
0.5
0.03
mA
nA
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
AC ELECTRICAL CHARACTERISTICS
(MAX2605–MAX2609 EV kits, VCC = +2.7V to +5.5V, VTUNE = 0.4V to 2.4V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +2.75V, VTUNE = 1.5V, and TA = +25°C.) (Note 1)
PARAMETER
Oscillator Nominal Frequency
Range (Note 4)
CONDITIONS
45
70
70
150
MAX2607
150
300
MAX2608
300
500
MAX2609
500
650
TA = +25°C
-4.1
+3.2
TA = -40°C to +85°C
-2.25
+2.25
TA = +25°C
-4.4
+3.4
TA = -40°C to +85°C
-2.5
+2.5
TA = +25°C
-4.6
+3.6
TA = -40°C to +85°C
-2.75
+2.75
TA = +25°C
-4.7
+3.6
TA = -40°C to +85°C
-2.8
+2.8
TA = +25°C
-5.0
+3.8
TA = -40°C to +85°C
-3.0
MAX2607
MAX2608
MAX2609
VTUNE = 0.4V to 0.6V step (Note 6)
Single-Ended Output Power
(Note 7)
Phase Noise (Note 8)
Maxim Integrated
MAX
MAX2605
MAX2606
Peak Tuning Gain
TYP
MAX2606
MAX2605
Guaranteed Frequency Limits
(relative to nominal) (Note 5)
MIN
fOFFSET = 100kHz
UNITS
MHz
%
+3.0
14.5
%/V
-10
dBm
MAX2605, QL ≥ 35
-117
MAX2606, QL ≥ 35
-112
MAX2607, QL ≥ 35
-107
MAX2608, QL ≥ 40
-100
MAX2609, QL ≥ 40
-93
dBc/Hz
3
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
AC ELECTRICAL CHARACTERISTICS (continued)
(MAX2605–MAX2609 EV kits, VCC = +2.7V to +5.5V, VTUNE = 0.4V to 2.4V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +2.75V, VTUNE = 1.5V, and TA = +25°C.) (Note 1)
PARAMETER
CONDITIONS
Even-Order Harmonics
Supply Pushing (Note 9)
MIN
TYP
Differential, RL = 50Ω each side
-30
MAX2605
60
MAX2606
120
MAX2607
220
MAX2608
480
MAX2609
720
MAX
UNITS
dBc
kHz/V
Note 1: Production tested at TA = +25°C. Maximum and minimum over temperature limits are guaranteed by design and
characterization.
Note 2: Supply current is measured while the part is oscillating and inductor Q ≥ QMIN. For MAX2605/MAX2606/MAX2607, QMIN = 35;
for MAX2608/MAX2609, QMIN = 40.
Note 3: The DC output current is the total available output signal current.
Note 4: Application range of the part is achieved using external inductance as specified in Figures 1-5 and shown in Figure 6. The internal varactors support center frequencies of 45MHz to 650MHz. The center frequency is defined by the value of the external
inductor element, LF. The application frequency limits are guaranteed by design and characterization.
Note 5: The guaranteed (tested) limits ƒMIN and ƒMAX are measured at VTUNE = 0.4V and VTUNE = 2.4V, respectively. Passing
requirements are: ƒ ≤ ƒMIN at VTUNE = 0.4 and ƒ ≥ ƒMAX at VTUNE = 2.4V. The nominal frequency of oscillation is defined by
the inductor.
Note 6: Describes peak tuning gain, which occurs at VTUNE = 0.4V.
Note 7: Measurement at OUT+ or OUT- matched for optimum power transfer into 50Ω load near the center of the operating frequency
range.
Note 8: The phase-noise specifications listed apply to the typical operating circuit shown in Figure 6. Apply over the entire operating
frequency range of the MAX2605–MAX2609.
Note 9: Supply pushing is measured with VCC stepped from +2.7V to +3.2V.
Typical Operating Characteristics
(MAX260_ EV kit, VCC = +2.75V, VTUNE = 1.4V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. TEMPERATURE
MAX2608 MAX2607
MAX2606
2.5
2.0
0.08
MAX2605/9-03
MAX2605/9-02
65
60
FREQUENCY (MHz)
MAX2609
LEAKAGE CURRENT (nA)
SUPPLY CURRENT (mA)
3.5
0.06
0.04
55
50
0.02
1.5
MAX2605
1.0
45
0
-40
-20
0
20
40
TEMPERATURE (°C)
4
0.10
MAX2605/9-01
4.0
3.0
MAX2605
VCO TUNING CURVE
TUNE INPUT LEAKAGE CURRENT
vs. TEMPERATURE
60
80
-40
-20
0
20
40
TEMPERATURE (°C)
60
80
0
0.5
1.0
1.5
2.0
2.5
3.0
VTUNE (V)
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
Typical Operating Characteristics (continued)
(MAX260_ EV kit, VCC = +2.75V, VTUNE = 1.4V, TA = +25°C, unless otherwise noted.)
MAX2607
VCO TUNING CURVE
430
MAX2605/9-05
260
MAX2605/9-04
130
MAX2608
VCO TUNING CURVE
240
110
100
FREQUENCY (MHz)
400
FREQUENCY (MHz)
FREQUENCY (MHz)
120
MAX2605/9-06
MAX2606
VCO TUNING CURVE
220
200
340
180
160
90
0
0.5
1.0
1.5
2.0
2.5
310
0
3.0
0.5
1.0
1.5
2.0
2.5
3.0
0
0.5
1.0
VTUNE (V)
VTUNE (V)
1.5
2.0
2.5
3.0
VTUNE (V)
MAX2609
VCO TUNING CURVE
OUTPUT SPECTRUM
640
MAX2605/9-08
0
MAX2605/9-07
680
-10
600
-20
(dB)
FREQUENCY (MHz)
370
560
-30
520
-40
-50
480
0
0.5
1.0
1.5
2.0
2.5
3.0
fo
2fo
3fo 4fo
5fo 6fo 7fo
FREQUENCY
VTUNE (V)
Pin Description
PIN
NAME
1
IND
Tuning Inductor Port. Connect an inductor from IND to GND to set VCO center frequency (see Oscillation
Frequency).
2
GND
Ground. Connect to the ground plane with a low-inductance path.
3
TUNE
Voltage-Control Input for Frequency Tuning. Input voltage range from +0.4V to +2.4V.
4
OUT-
High-Impedance Open-Collector Output. An external pull-up resistor or inductor to VCC is required. Output
power is dependent on external load impedance. OUT- is complementary to OUT+.
5
VCC
Supply Voltage Connection. Connect an external bypass capacitor to ground for low noise and low spurious-output content. See Layout Issues for more details.
6
OUT+
Maxim Integrated
FUNCTION
High-Impedance Open-Collector Output. An external pull-up resistor or inductor to VCC is required. Output
power is dependent on external load impedance. OUT+ is complementary to OUT-.
5
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
Detailed Description
The MAX2605–MAX2609 are low-noise VCOs designed
for fixed/single-frequency IF applications. The core
oscillator circuit is based on the well-known Colpitts
topology. The varactor and feedback capacitors are
integrated on-chip so that only an external inductor is
required to establish the frequency of oscillation and
produce a properly operating VCO. The tuning range,
biasing, startup, etc., are all managed within the IC. This
highly integrated design dramatically simplifies the
parts’ application.
The tuning range is wide enough so that, with the use
of ±2% tolerance inductors, no board-level adjustments
to the oscillation frequency are necessary. Once the
correct inductor value is chosen, the VCO is guaranteed always to tune to the desired operating frequency.
In addition, with the use of inductors of moderate Q (35
to 40), the VCO achieves excellent phase-noise performance.
Applications Information
Desired Oscillation Frequency
The desired VCO operating frequency is set by the
value of the external inductance, LF. Figures 1–5 show
the inductance value LF required to achieve the desired
oscillation frequency. The inductor value can be taken
directly from these figures. Inductance must be selected accurately to ensure proper operation over all conditions.
that required for LF. Choose LF2 to be a standard-value
inductor with a value just less than (LF - L F1 ). L F1
should adhere to the minimum Q requirements, but LF2
may be implemented as a lower-cost, lower-Q, thin-film
SMT inductor. Its lower Q has only a small impact on
the overall Q of the total inductance because it is <20%
of the total inductance. However, the overall Q of LF1
and LF2 must be greater than the minimum inductor Q
(Table 1).
It is also permissible to use PC board traces to provide
a small amount of inductance, thereby adjusting the
total inductance value. On the MAX2608/MAX2609, the
inductance values for LF2 are sometimes more exactly
implemented as a PC board trace (shorted to GND),
rather than an SMT inductor. When designing LF with
two inductors, use the simple model in Figure 7 to calculate XL and LEQ.
The LF in Figures 1–5 represents an equivalent inductance as seen by pin 1 (IND). The equivalent inductance corresponds to the inductive reactance
connected to IND at the desired oscillation frequency
(fNOMINAL).
LEQ = XL / (2π fNOMINAL) as seen in Figure 8
Inductor Implementation
Design L EQ = L F at the desired f NOMINAL . The
MAX2605–MAX2609 are designed to tolerate approximately 0.5pF of external parasitic capacitance at IND.
This parasitic capacitance arises from the pad capacitance at the device pin and pads for the inductor.
Additional shunt capacitance is not recommended
because it degrades the tuning range.
The inductance value required for the desired operating frequency may not necessarily coincide with a standard-value SMT inductor, which typically increases size
in ~1.2x steps. In such cases, the inductance must be
constructed from two inductors, LF1 and LF2, in order to
achieve the desired inductance value. Choose LF1 to
be a standard-value inductor with a value just less than
The MAX2605–MAX2609’s oscillator design uses a variant of the Colpitts topology, where DC bias for the varactor is applied via a DC voltage on TUNE and a
ground connection through the external inductor LF.
TUNE must also have a high-frequency AC ground for
Table 1. External Inductor LF Range
Table 2. CBYPASS Values
Bypass Capacitor on TUNE
FREQUENCY
RANGE
(MHz)
INDUCTANCE
RANGE
(nH)
MIN
INDUCTOR
Q
DEVICE
CBYPASS
MAX2605
45 to 70
680 ≤ LF ≤ 2200
35
MAX2605
≥ 820 pF
MAX2606
70 to 150
150 ≤ LF ≤ 820
35
MAX2606
≥ 680 pF
MAX2607
150 to 300
39 ≤ LF ≤ 180
35
MAX2607
≥ 330 pF
MAX2608
300 to 500
10 ≤ LF ≤ 47
40
MAX2608
≥ 100 pF
MAX2609
500 to 650
3.9 ≤ LF ≤ 15
40
MAX2609
≥ 39 pF
PART
6
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
MAX2605
REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY
1900
MEASUREMENT CONDITIONS
VCC = 2.75V, TA = 25°C,
RLOAD = 100Ω||50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω
VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω,
PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF
1800
THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE
REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO
CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING
CONDITIONS AND WORST-CASE COMPONENT
VALUES (±2% INDUCTOR AND IC PROCESS VARIATION).
1700
1600
REQUIRED INDUCTANCE (nH)
1500
1400
1300
1200
EFFECTIVE INDUCTANCE
FROM IND TO GND
1100
1000
INDUCTOR VALUE
MOUNTED ON EV KIT
900
800
700
45
47
49
51
53
55
57
59
61
63
65
67
69
DESIRED VCO FIXED FREQUENCY (MHz)
Figure 1. MAX2605 Required Inductance vs. Desired VCO Fixed Frequency
Maxim Integrated
7
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
MAX2606
REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY
790
MEASUREMENT CONDITIONS
VCC = 2.75V, TA = 25°C,
RLOAD = 100Ω||50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω
VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω,
PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF
740
690
THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE
REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO
CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING
CONDITIONS AND WORST-CASE COMPONENT
VALUES (±2% INDUCTOR AND IC PROCESS VARIATION).
640
REQUIRED INDUCTANCE (nH)
590
540
490
440
390
EFFECTIVE INDUCTANCE
FROM IND TO GND
340
290
INDUCTOR VALUE
MOUNTED ON EV KIT
240
190
140
70 75 80
85 90 95 100 105 110 115 120 125 130 135 140 145 150
DESIRED VCO FIXED FREQUENCY (MHz)
Figure 2. MAX2606 Required Inductance vs. Desired VCO Fixed Frequency
8
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
MAX2607
REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY
170
MEASUREMENT CONDITIONS
VCC = 2.75V, TA = 25°C,
RLOAD = 100Ω||50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω
VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω,
PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF
160
150
THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE
REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO
CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING
CONDITIONS AND WORST-CASE COMPONENT
VALUES (±2% INDUCTOR AND IC PROCESS VARIATION).
140
130
REQUIRED INDUCTANCE (nH)
120
110
100
90
80
EFFECTIVE INDUCTANCE
FROM IND TO GND
70
60
INDUCTOR VALUE
MOUNTED ON EV KIT
50
40
30
150 160 170 180 190 200
210
220 230 240
250 260 270 280 290 300
DESIRED VCO FIXED FREQUENCY (MHz)
Figure 3. MAX2607 Required Inductance vs. Desired VCO Fixed Frequency
Maxim Integrated
9
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
41.0
40.0
38.0
37.0
36.0
35.0
REQUIRED INDUCTANCE (nH)
34.0
33.0
32.0
31.0
30.0
29.0
28.0
27.0
MAX2608
REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY
MEASUREMENT CONDITIONS
VCC = 2.75V, TA = 25°C,
RLOAD = 100Ω||50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω
VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω,
PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF
THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE
REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO
CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING
CONDITIONS AND WORST-CASE COMPONENT
VALUES (±2% INDUCTOR AND IC PROCESS VARIATION).
26.0
25.0
24.0
23.0
22.0
EFFECTIVE INDUCTANCE
FROM IND TO GND
21.0
20.0
19.0
18.0
17.0
16.0
15.0
14.0
INDUCTOR VALUE
MOUNTED ON EV KIT
13.0
12.0
11.0
10.0
9.0
300 310 320 330 340 350 360 370 380 390 400 410 420 420 430 440 450 460 470 480 490 500
Figure 4. MAX2608 Required Inductance vs. Desired VCO Fixed Frequency
10
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
MAX2609
REQUIRED INDUCTANCE vs. DESIRED VCO FIXED FREQUENCY
14.0
MEASUREMENT CONDITIONS
VCC = 2.75V, TA = 25°C,
RLOAD = 100Ω||50Ω (100Ω RESISTIVE PULL-UP PARALLELED WITH 50Ω
VNA IMPEDANCE), UNUSED OUTPUT TERMINATED IN 50Ω,
PCB PARASITIC SHUNT CAPACITANCE (IND TO GND) = 0.45pF
13.5
13.0
12.5
THE INDUCTANCE LISTED IS THE PRECISE NOMINAL INDUCTANCE VALUE
REQUIRED FROM IND TO GND IN ORDER TO GUARANTEE THE VCO
CAN TUNE TO THE DESIRED FIXED FREQUENCY, OVER ALL OPERATING
CONDITIONS AND WORST-CASE COMPONENT
VALUES (±2% INDUCTOR AND IC PROCESS VARIATION).
12.0
11.5
11.0
REQUIRED INDUCTANCE (nH)
10.5
EFFECTIVE INDUCTANCE
FROM IND TO GND
10.0
9.5
9.0
8.5
8.0
7.5
7.0
6.5
6.0
INDUCTOR VALUE
MOUNTED ON EV KIT
5.5
5.0
4.5
4.0
3.5
500 510 520 530 540 550
560
570 580 590
600 610 620 630 640 650
DESIRED VCO FIXED FREQUENCY (MHz)
Figure 5. MAX2609 Required Inductance vs. Desired VCO Fixed Frequency
Maxim Integrated
11
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
the cathode of the varactor. This is accomplished
through the use of a simple bypass capacitor connected from TUNE to ground. The value of this capacitor
should be greater than or equal to the values listed in
Table 2.
This capacitor provides an AC “short” to ground for the
internal node of the varactor. It is acceptable to select
the next-largest standard-value capacitor. Use a
capacitor with a low-loss dielectric such as NPO; X7Rbased capacitors are not suitable. Omitting this capacitor would affect the tuning characteristics of the
MAX2605–MAX2609. Proper operation of the VCOs
requires the use of this bypass capacitor.
The MAX2605–MAX2609 VCO is designed to tune over
the full tuning range with a voltage range of 0.4V to
2.4V applied to TUNE. This voltage typically originates
from the output of the phase-locked (PLL) loop filter.
from OUT- and OUT+ (in place of resistors) to VCC to
provide DC bias for the output stage. The series capacitors are connected from OUT- and OUT+ to the load.
The values for LMATCH (Z1 and Z2) and CMATCH (C1
and C2) are chosen according to the operating frequency and load impedance. As the output stage is
essentially a high-speed current switch, traditional linear impedance using techniques with [S] parameters
do not apply. To achieve a reactive power match, start
with the component values provided in the EV kit, and
adjust values experimentally.
In general, the differential output may be applied in any
manner, as would conventional differential outputs. The
only constraints are the need for a pull-up element to
VCC and a voltage swing limit at the output pins OUTand OUT+.
Output Interface
In general, a properly designed PC board is essential
to any RF/microwave circuit or system. Always use controlled impedance lines (microstrip, coplanar waveguide, etc.) on high-frequency signals. Always place
decoupling capacitors as close to the VCC pin as possible. For low phase noise and spurious content, use an
appropriate size decoupling capacitor. For long VCC
lines, it may be necessary to add additional decoupling
capacitors located further from the device. Always provide a low-inductance path to ground. Keep the GND
vias as close to the device as possible. In addition, the
VCO should be placed as far away from the noisy section of a larger system, such as a switching regulator or
digital circuits. Use star topology to separate the
ground returns.
The resonator tank circuit (LF) is critical in determining
the VCO’s performance. For best performance, use
high-Q components and choose values carefully. To
minimize the effects of parasitic elements, which
degrade circuit performance, place LF and CBYP close
to their respective pins. Specifically, place CBYP directly across pins 2 (GND) and 3 (TUNE).
For the higher frequency versions, consider the extra
parasitic inductance and capacitance when determining the oscillation frequency. Be sure to account for the
following: PC board pad capacitance at IND, PC board
pad capacitance at the junction of two series inductors,
series inductance of any PC board traces, and the
inductance in the ground return path from the grounded side of the inductor and IC’s GND pin. For best
results, connect the “ground” side to the tuning inductor as close to pin 2 as possible. In addition, remove
the ground plane around and under LF and CBYP to
minimize the effects of parasitic capacitance.
The MAX2605–MAX2609 VCO includes a differential
output amplifier after the oscillator core. The amplifier
stage provides valuable isolation and offers a flexible
interface to the IF stages, such as a mixer and PLL
prescaler. The output can be taken single ended or differentially; however, the maximum output power and
lowest harmonic output are achieved in the differential
output mode.
Both outputs (OUT- and OUT+) are open-collector
types and require a pull-up element to VCC; this can be
either resistive or inductive. A resistor pull-up is the
most straightforward method of interfacing to the output, and works well in applications that operate at lower
frequencies or only require a modest voltage swing.
In Figure 6, Z1 and Z2 are 1kΩ pull-up resistors that are
connected from OUT+ and OUT- to VCC, respectively.
These resistors provide DC bias for the output amplifier
and are the maximum value permitted with compliance
to the output voltage swing limits. In addition, the 1kΩ
resistors maximize the swing at the load. DC-blocking
capacitors are connected from OUT- and OUT+ to the
load. If the load driven is primarily resistive and the
VCO operating frequency is below the -3dB bandwidth
of the output network, then the peak-to-peak differential
signal amplitude is approximately:
 1kΩ × R

LOAD
VOUTp −p diff = 2 × 1mA

 1kΩ + R

LOAD 
( )
To optimize the output voltage swing or the output
power, use a reactive power match. The matching network is a simple shunt-inductor series-capacitor circuit,
as shown in Figure 6. The inductors are connected
12
Layout Considerations
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
VCC
C1
1
LF
2
MAX2605
MAX2606
MAX2607
MAX2608
MAX2609
6
OUT+
RLOAD
Z1
C3
5
VCC
CBYP
Z2
RLOAD
C2
3
TUNE
4
OUT-
FROM PLL LOOP
FILTER OUTPUT
Figure 6. Typical Operating Circuit
Chip Information
TRANSISTOR COUNT: 158
Maxim Integrated
13
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
LEQ = XL / 2π ƒNOMINAL
IND
LF1
1
CPAR2
LF2
CPAR1
IND
MAX2605
MAX2606
MAX2607
MAX2608
MAX2609
1
XL
MAX2605
MAX2606
MAX2607
MAX2608
MAX2609
Figure 8. Inductive Reactance at Pin 1 (IND)
Figure 7. Simple Model of External Inductance
VCC
MAX2605
MAX2606
MAX2607
MAX2608
MAX2609
4
Γ
ZL
Figure 9. Output Matching Network
14
Maxim Integrated
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
6LSOT.EPS
Package Information
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© Maxim Integrated
15
The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc.