COILCRAFT 0402HL

Document 913-1
Chip Inductors – 0402HL (1005)
•Higher inductance values than other 0402 ceramic chip
inductors
•12 inductance values from 270 nH to 820 nH
Core material Ceramic
Inductance2 SRF typ3 DCR max4 Irms5
Part number1 ±5% (nH)
(MHz)
(Ohms) (mA)
Weight 0.7 – 1.3 mg
0402HL-271XJR_270
0402HL-301XJR_300
0402HL-331XJR_330
0402HL-361XJR_360
0402HL-391XJR_390
0402HL-471XJR_470
0402HL-511XJR_510
0402HL-561XJR_560
0402HL-601XJR_600
0402HL-681XJR_680
0402HL-741XJR_740
0402HL-821XJR_820
590
600
513
485
260
220
450
420
440
380
165
385
1.95
2.15
2.23
2.36
2.35
2.67
3.50
3.70
3.78
5.15
5.45
5.85
190
190
170
170
170
160
150
140
130
120
110
90
1. When ordering, please specify termination and packaging codes:
0402HL-821XJRW
Termination:R=RoHS compliant matte tin over nickel over silverplatinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:W
=7″ machine-ready reel. EIA-481 punched paper
tape (2000 parts per full reel).
U=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter W instead.
2. Inductance measured at 25 MHz using a Coilcraft SMD-F test fixture
and Coilcraft-provided correlation pieces with an Agilent/HP 4286
impedance analyzer.
3. SRF measured using Agilent/HP 8753D network analyzer and Coilcraft
SMD­‑D test fixture.
4. DCR measured on Cambridge Technology micro-ohmmeter and a
Coilcraft CCF858 test fixture.
5. Current that causes a 15°C temperature rise from 25°C ambient.
Because of their open construction, these parts will not saturate.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver-platinum-glass frit. Other terminations available at additional cost.
Ambient temperature –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +25 to +150 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 2000 per 7″ reel. Paper tape: 8 mm wide, 0.66 mm thick,
2 mm pocket spacing
PCB washing Only pure water or alcohol recommended
A max B max C max
D
E
F
G
H
I
0.048 0.031 0.022 0.010 0.0180.0080.0260.0140.025inches
1,22 0,79 0,56 0,25 0,460,200,660,360,64mm
Document 913-1 Revised 10/04/11
Document 913-2
Chip Inductors – 0402HL Series
L vs Frequency
Typical Q vs Frequency
Typical Impedance vs Frequency
Irms Derating
120
110
90
80
70
60
50
40
30
25°C
Percent of rated Irms
100
20
10
0
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
Document 913-2 Revised 10/04/11