LPC11Cx2/Cx4
32-bit ARM Cortex-M0 microcontroller; 16/32 kB flash, 8 kB
SRAM; C_CAN
Rev. 3.1 — 15 May 2013
Product data sheet
1. General description
The LPC11Cx2/Cx4 are an ARM Cortex-M0 based, low-cost 32-bit MCU family, designed
for 8/16-bit microcontroller applications, offering performance, low power, simple
instruction set and memory addressing together with reduced code size compared to
existing 8/16-bit architectures.
The LPC11Cx2/Cx4 operate at CPU frequencies of up to 50 MHz.
The peripheral complement of the LPC11Cx2/Cx4 includes 16/32 kB of flash memory,
8 kB of data memory, one C_CAN controller, one Fast-mode Plus I2C-bus interface, one
RS-485/EIA-485 UART, two SPI interfaces with SSP features, four general purpose
counter/timers, a 10-bit ADC, and up to 40 general purpose I/O pins.
On-chip C_CAN drivers and flash In-System Programming tools via C_CAN are included.
In addition, the LPC11C22 and LPC11C24 parts include an on-chip, high-speed CAN
transceiver.
2. Features and benefits
System:
ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
Serial Wire Debug.
System tick timer.
Memory:
32 kB (LPC11Cx4) or 16 kB (LPC11Cx2) on-chip flash program memory.
8 kB SRAM data memory.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software.
Flash ISP commands can be issued via UART or C_CAN.
Digital peripherals:
General Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors.
40 GPIO pins on the LPC11C12/C14 parts; 36 GPIO pins on the LPC11C22/C24
parts.
GPIO pins can be used as edge and level sensitive interrupt sources.
High-current output driver (20 mA) on one pin.
High-current sink drivers (20 mA) on two I2C-bus pins in Fast-mode Plus.
Four general purpose counter/timers with a total of four capture inputs and 13
(LPC11C12/C14) or 12 (LPC11C22/C24) match outputs.
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Programmable WatchDog Timer (WDT).
Analog peripherals:
10-bit ADC with input multiplexing among 8 pins.
Serial interfaces:
UART with fractional baud rate generation, internal FIFO, and RS-485 support.
Two SPI controllers with SSP features and with FIFO and multi-protocol
capabilities.
I2C-bus interface supporting full I2C-bus specification and Fast-mode Plus with a
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
C_CAN controller. On-chip C_CAN and CANopen drivers included.
On-chip, high-speed CAN transceiver (parts LPC11C22/C24 only).
Clock generation:
12 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used
as a system clock.
Crystal oscillator with an operating range of 1 MHz to 25 MHz.
Programmable watchdog oscillator with a frequency range of 7.8 kHz to 1.8 MHz.
PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from the system oscillator or the internal RC
oscillator.
Clock output function with divider that can reflect the system oscillator, IRC, CPU
clock, or the Watchdog clock.
Power control:
Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep, Deep-sleep, and Deep power-down modes.
Three reduced power modes: Sleep, Deep-sleep, and Deep power-down.
Processor wake-up from Deep-sleep mode via a dedicated start logic using 13 of
the GPIO pins.
Power-On Reset (POR).
Brownout detect with four separate thresholds for interrupt and forced reset.
Unique device serial number for identification.
Single 3.3 V power supply (1.8 V to 3.6 V).
Available as 48-pin LQFP package.
3. Applications
eMetering
Elevator systems
LPC11CX2_CX4
Product data sheet
Industrial and sensor based networks
White goods
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
2 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC11C12FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7 SOT313-2
1.4 mm
LPC11C14FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7 SOT313-2
1.4 mm
LPC11C22FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7 SOT313-2
1.4 mm
LPC11C24FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7 7 SOT313-2
1.4 mm
4.1 Ordering options
Table 2.
Ordering options
Type number
Flash
Total UART
SRAM RS-485
I2C/
SPI C_CAN C_CAN with GPIO
Fast+
on-chip
pins
CAN
transceiver
ADC
Package
channels
LPC11C12FBD48/301
16 kB
8 kB
1
1
2
1
no
40
8
LQFP48
LPC11C14FBD48/301
32 kB
8 kB
1
1
2
1
no
40
8
LQFP48
LPC11C22FBD48/301
16 kB
8 kB
1
1
2
1
yes
36
8
LQFP48
LPC11C24FBD48/301
32 kB
8 kB
1
1
2
1
yes
36
8
LQFP48
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
3 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
5. Block diagram
XTALIN
XTALOUT
RESET
SWD
LPC11Cx2/Cx4
IRC
TEST/DEBUG
INTERFACE
CLOCK
GENERATION,
POWER CONTROL,
SYSTEM
FUNCTIONS
POR
ARM
CORTEX-M0
system bus
clocks and
controls
FLASH
16/32 kB
slave
HIGH-SPEED
GPIO
GPIO ports
PIO0/1/2/3
CLKOUT
SRAM
8 kB
slave
ROM
slave
slave
AHB-LITE BUS
slave
AHB TO APB
BRIDGE
RXD
TXD
DTR, DSR, CTS,
DCD, RI, RTS
CT32B0_MAT[3:0]
CT32B0_CAP0
CT32B1_MAT[3:0]
CT32B1_CAP0
CT16B0_MAT[2:0]
CT16B0_CAP0
CT16B1_MAT[1:0](1)
CT16B1_CAP0
CAN_TXD
CAN_RXD
CANL, CANH
STB
VCC, VDD_CAN
UART
AD[7:0]
10-bit ADC
SPI0
SCK0, SSEL0
MISO0, MOSI0
SPI1
SCK1, SSEL1
MISO1, MOSI1
32-bit COUNTER/TIMER 0
32-bit COUNTER/TIMER 1
SCL
SDA
I2C-BUS
16-bit COUNTER/TIMER 0
WDT
16-bit COUNTER/TIMER 1
IOCONFIG
C_CAN (LPC11C12/C14)
SYSTEM CONTROL
C_CAN/
ON-CHIP TRANSCEIVER
(LPC11C22/C24)
PMU
002aaf265
(1) CT16B1_MAT0 not available on parts LPC11C22/C24.
Fig 1.
LPC11Cx2/Cx4 block diagram
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
4 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6. Pinning information
37 PIO3_1/DSR
38 PIO2_3/RI/MOSI1
39 SWDIO/PIO1_3/AD4/CT32B1_MAT2
40 PIO1_4/AD5/CT32B1_MAT3/WAKEUP
41 VSS
42 PIO1_11/AD7
43 PIO3_2/DCD
44 VDD
45 PIO1_5/RTS/CT32B0_CAP0
46 PIO1_6/RXD/CT32B0_MAT0
47 PIO1_7/TXD/CT32B0_MAT1
48 PIO3_3/RI
6.1 Pinning
PIO2_6
1
36 PIO3_0/DTR
PIO2_0/DTR/SSEL1
2
35 R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
3
34 R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
4
33 R/PIO1_0/AD1/CT32B1_CAP0
VSS
5
XTALIN
6
XTALOUT
7
VDD
8
29 SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
9
28 PIO0_9/MOSI0/CT16B0_MAT1
PIO0_2/SSEL0/CT16B0_CAP0 10
27 PIO0_8/MISO0/CT16B0_MAT0
32 R/PIO0_11/AD0/CT32B0_MAT3
30 PIO1_10/AD6/CT16B1_MAT1
PIO2_9 24
PIO0_7/CTS 23
PIO0_6/SCK0 22
PIO2_5 21
CAN_TXD 20
CAN_RXD 19
PIO2_4 18
PIO1_9/CT16B1_MAT0 17
PIO0_5/SDA 16
25 PIO2_10
PIO0_4/SCL 15
26 PIO2_2/DCD/MISO1
PIO2_8 12
PIO0_3 14
PIO2_7 11
PIO2_1/DSR/SCK1 13
Fig 2.
31 PIO2_11/SCK0
LPC11C12FBD48/301
LPC11C14FBD48/301
002aaf266
Pin configuration (LPC11C12/C14)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
5 of 62
LPC11Cx2/Cx4
NXP Semiconductors
37 PIO3_1/DSR
38 PIO2_3/RI/MOSI1
39 SWDIO/PIO1_3/AD4/CT32B1_MAT2
40 PIO1_4/AD5/CT32B1_MAT3/WAKEUP
41 VSS
42 PIO1_11/AD7
43 PIO3_2/DCD
44 VDD
45 PIO1_5/RTS/CT32B0_CAP0
46 PIO1_6/RXD/CT32B0_MAT0
47 PIO1_7/TXD/CT32B0_MAT1
48 PIO3_3/RI
32-bit ARM Cortex-M0 microcontroller
PIO2_6
1
36 PIO3_0/DTR
PIO2_0/DTR/SSEL1
2
35 R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
3
34 R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
4
33 R/PIO1_0/AD1/CT32B1_CAP0
VSS
5
32 R/PIO0_11/AD0/CT32B0_MAT3
XTALIN
6
XTALOUT
7
VDD
8
29 SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
9
28 PIO0_9/MOSI0/CT16B0_MAT1
PIO0_2/SSEL0/CT16B0_CAP0 10
27 PIO0_8/MISO0/CT16B0_MAT0
30 PIO1_10/AD6/CT16B1_MAT1
PIO0_7/CTS 24
PIO0_6/SCK0 23
STB 22
VCC 20
GND 21
CANH 19
CANL 18
VDD_CAN 17
PIO0_5/SDA 16
25 PIO2_10
PIO0_4/SCL 15
26 PIO2_2/DCD/MISO1
PIO2_8 12
PIO0_3 14
PIO2_7 11
PIO2_1/DSR/SCK1 13
Fig 3.
31 PIO2_11/SCK0
LPC11C22FBD48/301
LPC11C24FBD48/301
002aaf909
Pin configuration (LPC11C22/C24)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
6 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6.2 Pin description
Table 3.
LPC11C12/C14 pin description table
Symbol
Pin
Start Type
logic
inputs
Reset Description
state
[1]
PIO0_0 to PIO0_11
RESET/PIO0_0
PIO0_1/CLKOUT/
CT32B0_MAT2
Port 0 — Port 0 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 0 pins depends
on the function selected through the IOCONFIG register block.
3[2]
4[3]
yes
yes
I
I; PU
RESET — External reset input with 20 ns glitch filter. A LOW-going
pulse as short as 50 ns on this pin resets the device, causing I/O
ports and peripherals to take on their default states, and processor
execution to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns glitch
filter.
I/O
I; PU
PIO0_1 — General purpose digital input/output pin. A LOW level on
this pin during reset starts the flash ISP command handler via UART
(if PIO0_3 is HIGH) or via C_CAN (if PIO0_3 is LOW).
O
-
CLKOUT — Clockout pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
I/O
I; PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave Select for SPI0.
PIO0_2/SSEL0/
CT16B0_CAP0
10[3]
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
PIO0_3
14[3]
yes
I/O
I; PU
PIO0_3 — General purpose digital input/output pin. This pin is
monitored during reset: Together with a LOW level on pin PIO0_1, a
LOW level starts the flash ISP command handler via C_CAN and a
HIGH level starts the flash ISP command handler via UART.
PIO0_4/SCL
15[4]
yes
I/O
I; IA
PIO0_4 — General purpose digital input/output pin (open-drain).
I/O
-
SCL — I2C-bus, open-drain clock input/output. High-current sink only
if I2C Fast-mode Plus is selected in the I/O configuration register.
PIO0_5/SDA
16[4]
yes
yes
PIO0_6/SCK0
22[3]
yes
PIO0_7/CTS
23[3]
yes
PIO0_8/MISO0/
CT16B0_MAT0
27[3]
PIO0_9/MOSI0/
CT16B0_MAT1
28[3]
SWCLK/PIO0_10/
SCK0/
CT16B0_MAT2
LPC11CX2_CX4
Product data sheet
29[3]
yes
yes
yes
I/O
I; IA
PIO0_5 — General purpose digital input/output pin (open-drain).
I/O
-
SDA — I2C-bus, open-drain data input/output. High-current sink only
if I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I; PU
PIO0_6 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I/O
I; PU
PIO0_7 — General purpose digital input/output pin (high-current
output driver).
I
-
CTS — Clear To Send input for UART.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SPI0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SPI0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
7 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC11C12/C14 pin description table
Symbol
R/PIO0_11/
AD0/
CT32B0_MAT3
Pin
32[5]
Start Type
logic
inputs
Reset Description
state
yes
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
[1]
PIO1_0 to PIO1_11
R/PIO1_0/AD1/
CT32B1_CAP0
R/PIO1_1/AD2/
CT32B1_MAT0
R/PIO1_2/AD3/
CT32B1_MAT1
SWDIO/PIO1_3/
AD4/
CT32B1_MAT2
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
Port 1 — Port 1 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 1 pins depends
on the function selected through the IOCONFIG register block.
33[5]
34[5]
35[5]
39[5]
40[5]
PIO1_5/RTS/
CT32B0_CAP0
45[3]
PIO1_6/RXD/
CT32B0_MAT0
46[3]
LPC11CX2_CX4
Product data sheet
yes
no
no
no
no
no
no
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_4 — General purpose digital input/output pin with 10 ns glitch
filter.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns glitch
filter. This pin must be pulled HIGH externally to enter Deep
power-down mode and pulled LOW to exit Deep power-down mode.
A LOW-going pulse as short as 50 ns wakes up the part.
I/O
I; PU
PIO1_5 — General purpose digital input/output pin.
O
-
RTS — Request To Send output for UART.
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
8 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC11C12/C14 pin description table
Symbol
PIO1_7/TXD/
CT32B0_MAT1
Pin
47[3]
PIO1_8/
CT16B1_CAP0
9[3]
PIO1_9/
CT16B1_MAT0
17[3]
PIO1_10/AD6/
CT16B1_MAT1
30[5]
PIO1_11/AD7
42[5]
Start Type
logic
inputs
Reset Description
state
no
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
no
no
no
no
[1]
I/O
I; PU
PIO1_9 — General purpose digital input/output pin.
O
-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I/O
I; PU
PIO1_11 — General purpose digital input/output pin.
I
-
AD7 — A/D converter, input 7.
PIO2_0 to PIO2_11
PIO2_0/DTR/
SSEL1
Port 2 — Port 2 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 2 pins depends
on the function selected through the IOCONFIG register block.
2[3]
PIO2_1/DSR/SCK1 13[3]
PIO2_2/DCD/
MISO1
26[3]
PIO2_3/RI/MOSI1
38[3]
no
no
no
no
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
I/O
-
DTR — Data Terminal Ready output for UART.
I/O
-
SSEL1 — Slave Select for SPI1.
I/O
I; PU
PIO2_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
-
SCK1 — Serial clock for SPI1.
I/O
I; PU
PIO2_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART.
I/O
-
MISO1 — Master In Slave Out for SPI1.
I/O
I; PU
PIO2_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
I/O
-
MOSI1 — Master Out Slave In for SPI1.
PIO2_4
18[3]
no
I/O
I; PU
PIO2_4 — General purpose digital input/output pin.
PIO2_5
21[3]
no
I/O
I; PU
PIO2_5 — General purpose digital input/output pin.
PIO2_6
1[3]
no
I/O
I; PU
PIO2_6 — General purpose digital input/output pin.
PIO2_7
11[3]
no
I/O
I; PU
PIO2_7 — General purpose digital input/output pin.
PIO2_8
12[3]
no
I/O
I; PU
PIO2_8 — General purpose digital input/output pin.
PIO2_9
24[3]
no
I/O
I; PU
PIO2_9 — General purpose digital input/output pin.
PIO2_10
25[3]
no
I/O
I; PU
PIO2_10 — General purpose digital input/output pin.
PIO2_11/SCK0
31[3]
no
I/O
I; PU
PIO2_11 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
PIO3_0 to PIO3_3
LPC11CX2_CX4
Product data sheet
Port 3 — Port 3 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 3 pins depends
on the function selected through the IOCONFIG register block. Pins
PIO3_4 to PIO3_11 are not available.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
9 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC11C12/C14 pin description table
Symbol
Pin
Start Type
logic
inputs
Reset Description
state
I; PU
PIO3_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
I; PU
PIO3_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
[1]
PIO3_0/DTR
36[3]
no
PIO3_1/DSR
37[3]
no
PIO3_2/DCD
43[3]
no
PIO3_3/RI
48[3]
no
CAN_RXD
19[6]
CAN_TXD
20[6]
no
O
I; IA
CAN_TXD — C_CAN transmit data output.
VDD
8; 44
-
I
-
Supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
XTALIN
6[7]
-
I
-
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
XTALOUT
7[7]
-
O
-
Output from the oscillator amplifier.
VSS
5; 41
-
I
-
Ground.
I/O
DCD — Data Carrier Detect input for UART.
I
no
I/O
I; PU
PIO3_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
I
I; IA
CAN_RXD — C_CAN receive data input.
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to full VDD level); IA = inactive,
no pull-up/down enabled.
[2]
5 V tolerant pad. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to reset the chip and wake up
from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down mode. See Figure 26 for the
reset pad configuration.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 25).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 25).
[6]
5 V tolerant digital I/O pad without pull-up/pull-down resistors.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
Table 4.
LPC11C22/C24 pin description table
Symbol
Pin
Start Type
logic
inputs
Reset Description
state
[1]
PIO0_0 to PIO0_11
RESET/PIO0_0
LPC11CX2_CX4
Product data sheet
Port 0 — Port 0 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 0 pins depends
on the function selected through the IOCONFIG register block.
3[2]
yes
I
I; PU
RESET — External reset input with 20 ns glitch filter. A LOW-going
pulse as short as 50 ns on this pin resets the device, causing I/O
ports and peripherals to take on their default states, and processor
execution to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns glitch
filter.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
10 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC11C22/C24 pin description table
Symbol
PIO0_1/CLKOUT/
CT32B0_MAT2
Pin
4[3]
PIO0_2/SSEL0/
CT16B0_CAP0
10[3]
PIO0_3
14[3]
PIO0_4/SCL
15[4]
PIO0_5/SDA
16[4]
PIO0_6/SCK0
23[3]
PIO0_7/CTS
24[3]
PIO0_8/MISO0/
CT16B0_MAT0
27[3]
PIO0_9/MOSI0/
CT16B0_MAT1
28[3]
SWCLK/PIO0_10/
SCK0/
CT16B0_MAT2
29[3]
R/PIO0_11/
AD0/
CT32B0_MAT3
32[5]
PIO1_0 to PIO1_11
LPC11CX2_CX4
Product data sheet
Start Type
logic
inputs
Reset Description
state
yes
I/O
I; PU
PIO0_1 — General purpose digital input/output pin. A LOW level on
this pin during reset starts the flash ISP command handler via UART
(if PIO0_3 is HIGH) or via C_CAN (if PIO0_3 is LOW).
O
-
CLKOUT — Clockout pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
yes
[1]
I/O
I; PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave Select for SPI0.
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
yes
I/O
I; PU
PIO0_3 — General purpose digital input/output pin. This pin is
monitored during reset: Together with a LOW level on pin PIO0_1, a
LOW level starts the flash ISP command handler via C_CAN and a
HIGH level starts the flash ISP command handler via UART.
yes
I/O
I; IA
PIO0_4 — General purpose digital input/output pin (open-drain).
I/O
-
SCL — I2C-bus, open-drain clock input/output. High-current sink only
if I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I; IA
PIO0_5 — General purpose digital input/output pin (open-drain).
I/O
-
SDA — I2C-bus, open-drain data input/output. High-current sink only
if I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I; PU
PIO0_6 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I/O
I; PU
PIO0_7 — General purpose digital input/output pin (high-current
output driver).
I
-
CTS — Clear To Send input for UART.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SPI0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SPI0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
yes
yes
yes
yes
yes
yes
yes
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
Port 1 — Port 1 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 1 pins depends
on the function selected through the IOCONFIG register block.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
11 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC11C22/C24 pin description table
Symbol
R/PIO1_0/AD1/
CT32B1_CAP0
R/PIO1_1/AD2/
CT32B1_MAT0
R/PIO1_2/AD3/
CT32B1_MAT1
SWDIO/PIO1_3/
AD4/
CT32B1_MAT2
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
Pin
33[5]
34[5]
35[5]
39[5]
40[5]
Start Type
logic
inputs
Reset Description
state
yes
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
I; PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_4 — General purpose digital input/output pin with 10 ns glitch
filter.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns glitch
filter. This pin must be pulled HIGH externally to enter Deep
power-down mode and pulled LOW to exit Deep power-down mode.
A LOW-going pulse as short as 50 ns wakes up the part.
I/O
I; PU
PIO1_5 — General purpose digital input/output pin.
O
-
RTS — Request To Send output for UART.
no
no
no
no
PIO1_5/RTS/
CT32B0_CAP0
45[3]
PIO1_6/RXD/
CT32B0_MAT0
46[3]
PIO1_7/TXD/
CT32B0_MAT1
47[3]
PIO1_8/
CT16B1_CAP0
9[3]
no
PIO1_10/AD6/
CT16B1_MAT1
30[5]
no
LPC11CX2_CX4
Product data sheet
no
no
no
[1]
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
12 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC11C22/C24 pin description table
Symbol
PIO1_11/AD7
Pin
42[5]
Start Type
logic
inputs
Reset Description
state
no
I/O
I; PU
I
-
[1]
PIO1_11 — General purpose digital input/output pin.
AD7 — A/D converter, input 7.
PIO2_0 to PIO2_11
Port 2 — Port 2 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 2 pins depends
on the function selected through the IOCONFIG register block.
PIO2_0/DTR/
SSEL1
2[3]
PIO2_1/DSR/SCK1
13[3]
PIO2_2/DCD/
MISO1
26[3]
PIO2_3/RI/MOSI1
38[3]
no
no
no
no
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
I/O
-
DTR — Data Terminal Ready output for UART.
I/O
-
SSEL1 — Slave Select for SPI1.
I/O
I; PU
PIO2_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
-
SCK1 — Serial clock for SPI1.
I/O
I; PU
PIO2_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART.
I/O
-
MISO1 — Master In Slave Out for SPI1.
I/O
I; PU
PIO2_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
I/O
-
MOSI1 — Master Out Slave In for SPI1.
PIO2_6
1[3]
no
I/O
I; PU
PIO2_6 — General purpose digital input/output pin.
PIO2_7
11[3]
no
I/O
I; PU
PIO2_7 — General purpose digital input/output pin.
PIO2_8
12[3]
no
I/O
I; PU
PIO2_8 — General purpose digital input/output pin.
PIO2_10
25[3]
no
I/O
I; PU
PIO2_10 — General purpose digital input/output pin.
PIO2_11/SCK0
31[3]
no
I/O
I; PU
PIO2_11 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
PIO3_0 to PIO3_3
Port 3 — Port 3 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 3 pins depends
on the function selected through the IOCONFIG register block. Pins
PIO3_4 to PIO3_11 are not available.
PIO3_0/DTR
36[3]
PIO3_1/DSR
37[3]
PIO3_2/DCD
43[3]
PIO3_3/RI
48[3]
no
no
no
I/O
I; PU
PIO3_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
I; PU
PIO3_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
DCD — Data Carrier Detect input for UART.
I
no
I/O
I; PU
PIO3_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
CANL
18
no
I/O
-
LOW-level CAN bus line.
CANH
19
no
I/O
-
HIGH-level CAN bus line.
STB
22
no
I
-
Silent mode control input for CAN transceiver (LOW = Normal mode,
HIGH = silent mode).
VDD_CAN
17
-
-
-
Supply voltage for I/O level of CAN transceiver.
VCC
20
-
-
-
Supply voltage for CAN transceiver.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
13 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC11C22/C24 pin description table
Symbol
Pin
Start Type
logic
inputs
Reset Description
state
[1]
GND
21
-
-
-
Ground for CAN transceiver.
VDD
8; 44
-
I
-
Supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
XTALIN
6[7]
-
I
-
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
XTALOUT
7[7]
-
O
-
Output from the oscillator amplifier.
VSS
5; 41
-
I
-
Ground.
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to full VDD level); IA = inactive,
no pull-up/down enabled.
[2]
5 V tolerant pad. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to reset the chip and wake up
from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down mode. See Figure 26 for the
reset pad configuration.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 25).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 25).
[6]
5 V tolerant digital I/O pad without pull-up/pull-down resistors.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
14 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7. Functional description
7.1 ARM Cortex-M0 processor
The ARM Cortex-M0 is a general purpose, 32-bit microprocessor, which offers high
performance and very low power consumption.
7.2 On-chip flash program memory
The LPC11Cx2/Cx4 contain 32 kB (LPC11C14/C24) or 16 kB (LPC11C12/C22) of on-chip
flash program memory.
7.3 On-chip SRAM
The LPC11Cx2/Cx4 contain a total of 8 kB on-chip static RAM data memory.
7.4 Memory map
The LPC11Cx2/Cx4 incorporates several distinct memory regions, shown in the following
figures. Figure 4 shows the overall map of the entire address space from the user
program viewpoint following reset. The interrupt vector area supports address remapping.
The AHB peripheral area is 2 megabyte in size, and is divided to allow for up to 128
peripherals. The APB peripheral area is 512 kB in size and is divided to allow for up to 32
peripherals. Each peripheral of either type is allocated 16 kilobytes of space. This allows
simplifying the address decoding for each peripheral.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
15 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
AHB peripherals
LPC11Cx2/Cx4
4 GB
0x5020 0000
0xFFFF FFFF
reserved
0xE010 0000
private peripheral bus
16 - 127 reserved
0xE000 0000
0x5004 0000
reserved
AHB peripherals
12-15
GPIO PIO3
0x5020 0000
8-11
GPIO PIO2
0x5000 0000
4-7
GPIO PIO1
0-3
GPIO PIO0
APB peripherals
reserved
0x5003 0000
0x5002 0000
0x5001 0000
0x5000 0000
0x4008 0000
23 - 31 reserved
0x4005 C000
APB peripherals
1 GB
0x4008 0000
22
SPI1
0x4000 0000
21
reserved
20
C_CAN
19
reserved
18
system control
17
IOCONFIG
16
15
SPI0
flash controller
14
PMU
0x4005 4000
reserved
0x2000 0000
0.5 GB
reserved
0x4004 C000
0x4004 8000
0x4004 4000
0x4004 0000
0x4003 C000
0x4003 8000
0x4002 8000
0x1FFF 0000
reserved
0x1000 2000
8 kB SRAM
0x4005 0000
10 - 13 reserved
0x1FFF 4000
16 kB boot ROM
0x4005 8000
0x1000 0000
reserved
9
reserved
8
reserved
0x4002 0000
7
ADC
0x4001 C000
6
32-bit counter/timer 1
0x4001 8000
5
32-bit counter/timer 0
0x4001 4000
4
16-bit counter/timer 1
0x4001 0000
3
16-bit counter/timer 0
0x4000 C000
2
UART
0x4000 8000
1
0
WDT
0x4000 4000
I2C-bus
0x4000 0000
0x4002 4000
0x0000 8000
32 kB on-chip flash (LPC11Cx4)
16 kB on-chip flash (LPC11Cx2)
0 GB
0x0000 4000
0x0000 00C0
active interrupt vectors
0x0000 0000
0x0000 0000
002aaf268
Fig 4.
LPC11Cx2/Cx4 memory map
7.5 Nested Vectored Interrupt Controller (NVIC)
The Nested Vectored Interrupt Controller (NVIC) is an integral part of the Cortex-M0. The
tight coupling to the CPU allows for low interrupt latency and efficient processing of late
arriving interrupts.
7.5.1 Features
• Controls system exceptions and peripheral interrupts.
• In the LPC11Cx2/Cx4, the NVIC supports 32 vectored interrupts including 13 inputs to
the start logic from individual GPIO pins.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
16 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Four programmable interrupt priority levels, with hardware priority level masking.
• Software interrupt generation.
7.5.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of 40 pins (LPC11C12/C14) or 36 pins (LPC11C22/C24)) regardless
of the selected function, can be programmed to generate an interrupt on a level, or rising
edge or falling edge, or both.
7.6 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC11Cx2/Cx4 use accelerated GPIO functions:
• GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
• Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of 40 pins (LPC11C12/C14) or 36 pins (LPC11C22/C24))
providing a digital function can be programmed to generate an interrupt on a level, a rising
or falling edge, or both.
7.7.1 Features
• Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
• Direction control of individual bits.
• All GPIO pins default to inputs with pull-ups enabled after reset except for the I2C-bus
true open-drain pins PIO0_4 and PIO0_5.
• Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin (except PIO0_4 and PIO0_5).
• All GPIO pins (except PIO0_4 and PIO0_5) are pulled up to 3.3 V (VDD = 3.3 V) if their
pull-up resistor is enabled in the IOCONFIG block.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
17 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.8 UART
The LPC11Cx2/Cx4 contain one UART.
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.8.1 Features
•
•
•
•
•
Maximum UART data bit rate of 3.125 Mbit/s.
16 Byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• FIFO control mechanism that enables software flow control implementation.
• Support for RS-485/9-bit mode.
• Support for modem control.
7.9 SPI serial I/O controller
The LPC11Cx2/Cx4 contain two SPI controllers. Both SPI controllers support SSP
features.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
7.9.1 Features
• Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
7.10 I2C-bus serial I/O controller
The LPC11Cx2/Cx4 contain one I2C-bus controller.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
18 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial CLock line
(SCL) and a Serial DAta line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be
controlled by more than one bus master connected to it.
7.10.1 Features
• The I2C-interface is a standard I2C-bus compliant interface with open-drain pins. The
I2C-bus interface also supports Fast-mode Plus with bit rates up to 1 Mbit/s.
•
•
•
•
•
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
• The I2C-bus controller supports multiple address recognition and a bus monitor mode.
7.11 C_CAN controller
Controller Area Network (CAN) is the definition of a high performance communication
protocol for serial data communication. The C_CAN controller is designed to provide a full
implementation of the CAN protocol according to the CAN Specification Version 2.0B. The
C_CAN controller allows to build powerful local networks with low-cost multiplex wiring by
supporting distributed real-time control with a very high level of security.
On-chip C_CAN drivers provide an API for initialization and communication using CAN
and CANopen standards.
7.11.1 Features
•
•
•
•
•
•
•
Conforms to protocol version 2.0 parts A and B.
Supports bit rate of up to 1 Mbit/s.
Supports 32 Message Objects.
Each Message Object has its own identifier mask.
Provides programmable FIFO mode (concatenation of Message Objects).
Provides maskable interrupts.
Supports Disabled Automatic Retransmission (DAR) mode for time-triggered CAN
applications.
• Provides programmable loop-back mode for self-test operation.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
19 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• The C_CAN API includes the following functions:
– C_CAN set-up and initialization
– C_CAN send and receive messages
– C_CAN status
– CANopen object dictionary
– CANopen SDO expedited communication
– CANopen SDO segmented communication primitives
– CANopen SDO fall-back handler
• Flash ISP programming via C_CAN supported.
7.11.2 On-chip, high-speed CAN transceiver
Remark: The on-chip CAN transceiver is available on parts LPC11C22/C24 only.
Compared to the LPC11C12/C14, the LPC11C22/C24 supports fewer GPIO functions,
and in addition, one counter/timer match function is removed to allow interfacing the CAN
high-speed transceiver to the CAN bus. See Table 4 and Figure 1.
7.11.2.1
Features
•
•
•
•
7.11.2.2
Data rates of up to 1 Mbit/s
Fully ISO 11898-2 compliant
Undervoltage detection and thermal protection
Low ElectroMagnetic Emission (EME) and high ElectroMagnetic Immunity (EMI)
Normal mode
A LOW level on pin STB selects Normal mode. In this mode, the transceiver is able to
transmit and receive data via the bus lines CANH and CANL (see Figure 28). The
differential receiver converts the analog data on the bus lines into digital data which are
received by the CAN_RXD input of the C_CAN controller.
7.11.2.3
Silent mode
A HIGH level on pin STB selects Silent mode. In Silent mode the transmitter is disabled,
releasing the bus pins to recessive state. All other functions, including the receiver,
continue to operate as in Normal mode. Silent mode can be used to prevent a faulty
C_CAN controller from disrupting all network communications.
7.11.2.4
Undervoltage protection
Should VCC or VDD_CAN drop below their respective undervoltage detection levels
(Vuvd(VCC) and Vuvd (VDD_CAN); see Table 8), the transceiver will switch off and disengage
from the bus (zero load) until VCC and VDD_CAN have recovered.
7.11.2.5
Thermal protection
The output drivers are protected against overtemperature conditions. If the virtual junction
temperature exceeds the shutdown junction temperature, Tj(sd) (see Table 8), the output
drivers will be disabled until the virtual junction temperature falls below Tj(sd).
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
20 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.11.2.6
Time-out function
A ‘TXD dominant time-out’ timer is started when the CAN_TXD signal of the C_CAN
controller is set LOW. If the LOW state on the CAN_TXD signal persists for longer than
tto(dom)TXD, the transmitter is disabled, releasing the bus lines to recessive state. This
function prevents a hardware and/or software application failure from driving the bus lines
to a permanent dominant state (blocking all network communications). The TXD dominant
time-out timer is reset when the CAN_TXD signal is set HIGH. The TXD dominant
time-out time also defines the minimum possible bit rate of 40 kbit/s.
7.12 10-bit ADC
The LPC11Cx2/Cx4 contains one ADC. The ADC is a single 10-bit successive
approximation ADC with eight channels.
7.12.1 Features
•
•
•
•
•
•
•
•
10-bit successive approximation ADC.
Input multiplexing among 8 pins.
Power-down mode.
Measurement range 0 V to VDD.
10-bit conversion time 2.44 s (up to 400 kSamples/s).
Burst conversion mode for single or multiple inputs.
Optional conversion on transition of input pin or timer match signal.
Individual result registers for each ADC channel to reduce interrupt overhead.
7.13 General purpose external event counter/timers
The LPC11Cx2/Cx4 includes two 32-bit counter/timers and two 16-bit counter/timers. The
counter/timer is designed to count cycles of the system derived clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. Each counter/timer also includes one capture input to trap the timer value
when an input signal transitions, optionally generating an interrupt.
7.13.1 Features
• A 32-bit/16-bit timer/counter with a programmable 32-bit/16-bit prescaler.
• Counter or timer operation.
• One capture channel per timer, that can take a snapshot of the timer value when an
input signal transitions. A capture event may also generate an interrupt.
• Four match registers per timer that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
21 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
– Toggle on match.
– Do nothing on match.
7.14 System tick timer
The ARM Cortex-M0 includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a fixed time interval (typically 10 ms).
7.15 Watchdog timer
The purpose of the watchdog is to reset the microcontroller within a selectable time
period.
7.15.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect/Incomplete feed sequence causes reset/interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK) 256 4) to (Tcy(WDCLK) 224 4) in
multiples of Tcy(WDCLK) 4.
• The Watchdog Clock (WDCLK) source can be selected from the Internal RC oscillator
(IRC), the Watchdog oscillator, or the main clock. This gives a wide range of potential
timing choices of Watchdog operation under different power reduction conditions. It
also provides the ability to run the WDT from an entirely internal source that is not
dependent on an external crystal and its associated components and wiring for
increased reliability.
7.16 Clocking and power control
7.16.1 Crystal oscillators
The LPC11Cx2/Cx4 include three independent oscillators. These are the system
oscillator, the Internal RC oscillator (IRC), and the Watchdog oscillator. Each oscillator can
be used for more than one purpose as required in a particular application.
Following reset, the LPC11Cx2/Cx4 will operate from the Internal RC oscillator until
switched by software. This allows systems to operate without any external crystal and the
bootloader code to operate at a known frequency.
See Figure 5 for an overview of the LPC11Cx2/Cx4 clock generation.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
22 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
SYSTEM CLOCK
DIVIDER
AHB clock 0
(system)
system clock
18
AHB clocks 1 to 18
(memories
and peripherals)
SYSAHBCLKCTRL[1:18]
(AHB clock enable)
IRC oscillator
SPI0 PERIPHERAL
CLOCK DIVIDER
SPI0
UART PERIPHERAL
CLOCK DIVIDER
UART
SPI1 PERIPHERAL
CLOCK DIVIDER
SPI1
WDT CLOCK
DIVIDER
WDT
main clock
watchdog oscillator
MAINCLKSEL
(main clock select)
IRC oscillator
SYSTEM PLL
system oscillator
IRC oscillator
SYSPLLCLKSEL
(system PLL clock select)
watchdog oscillator
WDTUEN
(WDT clock update enable)
IRC oscillator
system oscillator
watchdog oscillator
CLKOUTUEN
(CLKOUT update enable)
Fig 5.
CLKOUT PIN CLOCK
DIVIDER
CLKOUT pin
002aae514
LPC11Cx2/Cx4 clock generation block diagram
7.16.1.1
Internal RC oscillator
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
PLL and subsequently the CPU. The nominal IRC frequency is 12 MHz. The IRC is
trimmed to 1 % accuracy over the entire voltage and temperature range.
Upon power-up or any chip reset, the LPC11Cx2/Cx4 use the IRC as the clock source.
Software may later switch to one of the other available clock sources.
7.16.1.2
System oscillator
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
23 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.16.1.3
Watchdog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 7.8 kHz and 1.7 MHz. The frequency spread over processing and
temperature is 40 % (see Table 15).
7.16.2 System PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
its frequency range while the PLL is providing the desired output frequency. The output
divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. The PLL output
frequency must be lower than 100 MHz. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100 s.
7.16.3 Clock output
The LPC11Cx2/Cx4 features a clock output function that routes the IRC oscillator, the
system oscillator, the watchdog oscillator, or the main clock to an output pin.
7.16.4 Wake-up process
The LPC11Cx2/Cx4 begin operation at power-up and when awakened from Deep
power-down mode by using the 12 MHz IRC oscillator as the clock source. This allows
chip operation to resume quickly. If the system oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
7.16.5 Power control
The LPC11Cx2/Cx4 support a variety of power control features. There are three special
modes of processor power reduction: Sleep mode, Deep-sleep mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, a register is provided for shutting down the clocks to individual on-chip
peripherals, allowing fine tuning of power consumption by eliminating all dynamic power
use in any peripherals that are not required for the application. Selected peripherals have
their own clock divider which provides even better power control.
7.16.5.1
Sleep mode
When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep
mode does not need any special sequence but re-enabling the clock to the ARM core.
In Sleep mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Sleep mode and may generate
interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
24 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.16.5.2
Deep-sleep mode
In Deep-sleep mode, the chip is in Sleep mode, and in addition all analog blocks are shut
down. As an exception, the user has the option to keep the watchdog oscillator and the
BOD circuit running for self-timed wake-up and BOD protection. Deep-sleep mode allows
for additional power savings.
Up to 13 pins total, see Table 3, serve as external wake-up pins to a dedicated start logic
to wake up the chip from Deep-sleep mode.
Unless the watchdog oscillator is selected to run in Deep-sleep mode, the clock source
should be switched to IRC before entering Deep-sleep mode, because the IRC can be
switched on and off glitch-free.
7.16.5.3
Deep power-down mode
In Deep power-down mode, power is shut off to the entire chip with the exception of the
WAKEUP pin. The LPC11Cx2/Cx4 can wake up from Deep power-down mode via the
WAKEUP pin.
When entering Deep power-down mode, an external pull-up resistor is required on the
WAKEUP pin to hold it HIGH. The RESET pin must also be held HIGH to prevent it from
floating while in Deep power-down mode.
7.17 System control
7.17.1 Start logic
The start logic connects external pins to corresponding interrupts in the NVIC. Each pin
shown in Table 3 as input to the start logic has an individual interrupt in the NVIC interrupt
vector table. The start logic pins can serve as external interrupt pins when the chip is
running. In addition, an input signal on the start logic pins can wake up the chip from
Deep-sleep mode when all clocks are shut down.
The start logic must be configured in the system configuration block and in the NVIC
before being used.
7.17.2 Reset
Reset has four sources on the LPC11Cx2/Cx4: the RESET pin, the Watchdog reset,
power-on reset (POR), and the BrownOut Detection (BOD) circuit. The RESET pin is a
Schmitt trigger input pin. Assertion of chip reset by any source, once the operating voltage
attains a usable level, starts the IRC and initializes the flash controller.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the boot block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
An external pull-up resistor is required on the RESET pin if Deep power-down mode is
used.
7.17.3 Brownout detection
The LPC11Cx2/Cx4 includes four levels for monitoring the voltage on the VDD pin. If this
voltage falls below one of the four selected levels, the BOD asserts an interrupt signal to
the NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
25 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
NVIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading
a dedicated status register. Four additional threshold levels can be selected to cause a
forced reset of the chip.
7.17.4 Code security (Code Read Protection - CRP)
This feature of the LPC11Cx2/Cx4 allows user to enable different levels of security in the
system so that access to the on-chip flash and use of the Serial Wire Debugger (SWD)
and In-System Programming (ISP) can be restricted. When needed, CRP is invoked by
programming a specific pattern into a dedicated flash location. IAP commands are not
affected by the CRP.
In addition, ISP entry via the PIO0_1 pin can be disabled without enabling CRP. For
details see the LPC11Cx user manual.
There are three levels of Code Read Protection:
1. CRP1 disables access to the chip via the SWD and allows partial flash update
(excluding flash sector 0) using a limited set of the ISP commands. This mode is
useful when CRP is required and flash field updates are needed but all sectors can
not be erased.
2. CRP2 disables access to the chip via the SWD and only allows full flash erase and
update using a reduced set of the ISP commands.
3. Running an application with level CRP3 selected fully disables any access to the chip
via the SWD pins and the ISP. This mode effectively disables ISP override using
PIO0_1 pin, too. It is up to the user’s application to provide (if needed) flash update
mechanism using IAP calls or call reinvoke ISP command to enable flash update via
the UART.
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
In addition to the three CRP levels, sampling of pin PIO0_1 for valid user code can be
disabled. For details see the LPC11Cx user manual.
7.17.5 Bootloader
The bootloader controls initial operation after reset and also provides the means to
program the flash memory. This could be initial programming of a blank device, erasure
and re-programming of a previously programmed device, or programming of the flash
memory by the application program in a running system.
The bootloader code is executed every time the part is reset or powered up. The loader
can either execute the user application code or the ISP command handler via UART or
C_CAN. A LOW level during reset applied to the PIO0_1 pin is considered as an external
hardware request to start the ISP command handler. The state of PIO0_3 at reset
determines whether the UART (PIO0_3 HIGH) or the C_CAN (PIO0_3 LOW) interface will
be used.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
26 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
The C_CAN ISP command handler uses the CANopen protocol and data organization
method. C_CAN ISP commands have the same functionality as UART ISP commands.
7.17.6 APB interface
The APB peripherals are located on one APB bus.
7.17.7 AHBLite
The AHBLite connects the CPU bus of the ARM Cortex-M0 to the flash memory, the main
static RAM, and the Boot ROM.
7.17.8 External interrupt inputs
All GPIO pins can be level or edge sensitive interrupt inputs. In addition, start logic inputs
serve as external interrupts (see Section 7.17.1).
7.18 Emulation and debugging
Debug functions are integrated into the ARM Cortex-M0. Serial wire debug with four
breakpoints and two watchpoints is supported.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
27 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
VDD
supply voltage (core
and external rail)
on pins VDD
[2]
VI
input voltage
5 V tolerant I/O pins; only valid when the VDD supply
voltage is present
[3]
Vx
voltage on pin x
no time limit; DC value
supply current
IDD
ISS
ground current
Ilatch
I/O latch-up current
Min
Max
Unit
0.5
4.6
V
0.5
+5.5
V
on pins CANH and CANL
58
+58
V
on pins STB, VCC, VDD_CAN
0.3
+7
V
per supply pin
[4]
-
100
mA
per ground pin
[4]
-
100
mA
-
100
mA
65
+150
C
(0.5VDD) < VI < (1.5VDD);
Tj < 125 C
[5]
Tstg
storage temperature
Tj(max)
maximum junction
temperature
-
150
C
Ptot(pack)
total power dissipation based on package heat transfer, not device power
(per package)
consumption
-
1.5
W
VESD
electrostatic discharge human body model;
voltage
all pins except CAN on-chip transceiver pins CANL,
CANH, STB, VDD_CAN, VCC, GND on
LPC11C22/C24
[6]
6500
+6500
V
pins CANH and CANL on LPC11C22/C24
[6]
8000
+8000
V
pins STB, VDD_CAN, VCC, GND on
LPC11C22/C24
[6]
4000
+4000
V
[1]
non-operating
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Maximum/minimum voltage above the maximum operating voltage (see Table 6) and below ground that can be applied for a short time
(<10 ms) to a device without leading to irrecoverable failure. Failure includes the loss of reliability and shorter lifetime of the device.
[3]
Including voltage on outputs in 3-state mode.
[4]
The peak current is limited to 25 times the corresponding maximum current.
[5]
The maximum non-operating storage temperature is different than the temperature for required shelf life which should be determined
based on required shelf lifetime. Please refer to the JEDEC spec (J-STD-033B.1) for further details.
[6]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
28 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9. Static characteristics
Table 6.
Static characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
VDD
supply voltage (core
and external rail)
on pins VDD
1.8
3.3
3.6
V
IDD
supply current
Active mode; code
-
3
-
mA
-
9
-
mA
-
2
-
mA
-
6
-
A
-
220
-
nA
while(1){}
executed from flash
system clock = 12 MHz
VDD = 3.3 V
system clock = 50 MHz
VDD = 3.3 V
Sleep mode;
system clock = 12 MHz
[2][3][4]
[5][6][7]
[2][3][6]
[5][7][8]
[2][3][4]
[5][6][7]
VDD = 3.3 V
Deep-sleep mode;
VDD = 3.3 V
Deep power-down mode;
VDD = 3.3 V
[2][3][5]
[9]
[2][10]
Standard port pins, RESET
IIL
LOW-level input current VI = 0 V; on-chip pull-up
resistor disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip
pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD;
on-chip pull-up/down
resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide
a digital function
0
-
5.0
V
0
-
VDD
V
[11][12]
VO
output voltage
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
-
0.4
-
V
VOH
HIGH-level output
voltage
2.0 V VDD 3.6 V;
IOH = 4 mA
VDD 0.4
-
-
V
1.8 V VDD < 2.0 V;
IOH = 3 mA
VDD 0.4
-
-
V
2.0 V VDD 3.6 V;
IOL = 4 mA
-
-
0.4
V
1.8 V VDD < 2.0 V;
IOL = 3 mA
-
-
0.4
V
VOL
LPC11CX2_CX4
Product data sheet
LOW-level output
voltage
output active
[13]
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
29 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 6.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
IOH
HIGH-level output
current
VOH = VDD 0.4 V;
4
-
-
mA
3
-
-
mA
4
-
-
mA
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
IOL
LOW-level output
current
VOL = 0.4 V
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
3
-
-
mA
-
-
45
mA
-
-
50
mA
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[14]
IOLS
LOW-level short-circuit
output current
VOL = VDD
[14]
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V;
15
50
85
A
10
50
85
A
0
0
0
A
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
VDD < VI < 5 V
High-drive output pin (PIO0_7)
IIL
LOW-level input current VI = 0 V; on-chip pull-up
resistor disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip
pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD;
on-chip pull-up/down
resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide
a digital function
0
-
5.0
V
0
-
VDD
V
[11][12]
[13]
VO
output voltage
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
0.4
-
-
V
VOH
HIGH-level output
voltage
2.5 V VDD 3.6 V;
IOH = 20 mA
VDD 0.4
-
-
V
1.8 V VDD < 2.5 V;
IOH = 12 mA
VDD 0.4
-
-
V
2.0 V VDD 3.6 V;
IOL = 4 mA
-
-
0.4
V
1.8 V VDD < 2.0 V;
IOL = 3 mA
-
-
0.4
V
VOH = VDD 0.4 V;
2.5 V VDD 3.6 V
20
-
-
mA
1.8 V VDD < 2.5 V
12
-
-
mA
VOL
IOH
LPC11CX2_CX4
Product data sheet
LOW-level output
voltage
HIGH-level output
current
output active
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
30 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 6.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
IOL
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
3
-
-
mA
-
-
50
mA
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
[14]
IOLS
LOW-level short-circuit
output current
VOL = VDD
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V
15
50
85
A
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
VDD < VI < 5 V
I2C-bus
10
50
85
A
0
0
0
A
pins (PIO0_4 and PIO0_5)
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
-
0.05VDD
-
V
3.5
-
-
mA
LOW-level output
current
IOL
I2C-bus
VOL = 0.4 V;
pins
configured as standard
mode pins
2.0 V VDD 3.6 V
LOW-level output
current
IOL
1.8 V VDD < 2.0 V
3
-
-
VOL = 0.4 V; I2C-bus pins
configured as Fast-mode
Plus pins
20
-
-
16
-
-
-
2
4
A
-
10
22
A
mA
2.0 V VDD 3.6 V
1.8 V VDD < 2.0 V
input leakage current
ILI
VI = VDD
VI = 5 V
[15]
Oscillator pins
Vi(xtal)
crystal input voltage
0.5
1.8
1.95
V
Vo(xtal)
crystal output voltage
0.5
1.8
1.95
V
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
[2]
Tamb = 25 C.
[3]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[4]
IRC enabled; system oscillator disabled; system PLL disabled.
[5]
Pin CAN_RXD pulled LOW externally.
[6]
BOD disabled.
[7]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART and SPI0/1 disabled in system configuration
block.
[8]
IRC disabled; system oscillator enabled; system PLL enabled.
[9]
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 18FF.
[10] WAKEUP pin pulled HIGH externally.
[11] Including voltage on outputs in 3-state mode.
[12] VDD supply voltage must be present.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
31 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
[13] 3-state outputs go into 3-state mode in Deep power-down mode.
[14] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[15] To VSS.
9.1 ADC characteristics
Table 7.
ADC static characteristics
Tamb = 40 C to +85 C unless otherwise specified; ADC frequency 4.5 MHz, VDD = 2.5 V to 3.6 V.
Symbol
Parameter
VIA
analog input voltage
Cia
analog input capacitance
Conditions
Min
Typ
Max
Unit
0
-
VDD
V
pF
-
-
1
[1][2]
ED
differential linearity error
-
-
1
LSB
EL(adj)
integral non-linearity
[3]
-
-
1.5
LSB
EO
offset error
[4]
-
-
3.5
LSB
gain error
[5]
-
-
0.6
%
[6]
EG
ET
absolute error
Rvsi
voltage source interface
resistance
Ri
input resistance
[7][8]
-
-
4
LSB
-
-
40
k
-
-
2.5
M
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 6.
[3]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 6.
[4]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 6.
[5]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 6.
[6]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve. See Figure 6.
[7]
Tamb = 25 C; maximum sampling frequency fs = 400 kSamples/s and analog input capacitance Cia = 1 pF.
[8]
Input resistance Ri depends on the sampling frequency fs: Ri = 1 / (fs Cia).
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
32 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
offset error
EO
1 LSB =
VDD − VSS
1024
002aaf426
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 6.
ADC characteristics
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
33 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.2 C_CAN on-chip, high-speed transceiver characteristics
Table 8.
Static characteristics
Tamb = 40 C to +85 C; VCC = 4.5 V to 5.5 V; RL = 60 ; unless otherwise specified; all voltages are defined with respect to
ground; positive currents flow into the IC. Also see Figure 28.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
4.5
-
5.5
V
0.1
1
2.5
mA
Supply; pin VCC
VCC
supply voltage
ICC
supply current
Silent mode
Normal mode
Vuvd(VCC)
recessive
2.5
5
10
mA
dominant; CAN_TXD = LOW
20
50
70
mA
3.5
-
4.5
V
2.8
-
5.5
V
undervoltage detection
voltage on pin VCC
I/O level adapter supply; pin VDD_CAN
VDD
supply voltage
on pin VDD_CAN
IDD
supply current
on pin VDD_CAN; Normal and Silent
modes
[1]
recessive; CAN_TXD = HIGH
10
80
250
A
dominant; CAN_TXD = LOW
50
350
500
A
1.3
-
2.7
V
Vuvd(VDD_CAN) undervoltage detection
voltage on pin VDD_CAN
Mode control input; pin STB
VIH
HIGH-level input voltage
0.7VCC
-
VCC + 0.3 V
VIL
LOW-level input voltage
0.3
-
0.3VCC
V
IIH
HIGH-level input current
1
4
10
A
IIL
LOW-level input current
1
0
+1
A
2.75
3.5
4.5
V
Voltage on pin STB = 0 V
Bus lines; pins CANH and CANL
VO(dom)
dominant output voltage
CAN_TXD = LOW; t < tto(dom)TXD
pin CANH
0.5
1.5
2.25
V
Vdom(TX)sym
transmitter dominant voltage Vdom(TX)sym = VCC VCANH VCANL
symmetry
pin CANL
400
0
+400
mV
VO(dif)bus
bus differential output
voltage
CAN_TXD = LOW; t < tto(dom)TXD
1.5
-
3
V
CAN_TXD = HIGH; recessive;
no load
50
-
+50
mV
VO(rec)
recessive output voltage
Normal and Silent modes;
CAN_TXD = HIGH; no load
2
0.5VCC 3
V
Vth(RX)dif
differential receiver
threshold voltage
Normal and Silent modes
Vcm(CAN)[2] = 12 V to +12 V
0.5
0.7
0.9
V
Vhys(RX)dif
differential receiver
hysteresis voltage
Normal and Silent modes
Vcm(CAN) = 12 V to +12 V
50
120
400
mV
IO(dom)
dominant output current
CAN_TXD = LOW; t < tto(dom)TXD;
VCC = 5 V
pin CANH; VCANH = 0 V
120
70
40
mA
pin CANL; VCANL = 5 V/40 V
40
70
120
mA
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
34 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 8.
Static characteristics …continued
Tamb = 40 C to +85 C; VCC = 4.5 V to 5.5 V; RL = 60 ; unless otherwise specified; all voltages are defined with respect to
ground; positive currents flow into the IC. Also see Figure 28.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
IO(rec)
recessive output current
Normal and Silent modes;
CAN_TXD = HIGH;
VCANH = VCANL = 27 V to +32 V
5
-
+5
mA
IL
leakage current
VCC = 0 V; VCANH = VCANL = 5 V
5
0
+5
A
Ri
input resistance
9
15
28
k
Ri
input resistance deviation
3
0
+3
%
Ri(dif)
differential input resistance
19
30
52
k
Ci(cm)
common-mode input
capacitance
-
-
20
pF
Ci(dif)
differential input capacitance
-
-
10
pF
-
190
-
C
between VCANH and VCANL
Temperature protection
Tj(sd)
shutdown junction
temperature
[1]
VDD_CAN must be equal to the VDD of the microcontroller
[2]
Vcm(CAN) is the common mode voltage of CANH and CANL.
Table 9.
Dynamic characteristics
Tamb = 40 C to +85 C; VCC = 4.5 V to 5.5 V; RL = 60 unless specified otherwise. All voltages are defined with respect to
ground. Positive currents flow into the IC.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tto(dom)TXD
TXD dominant time-out time
CAN_TXD = LOW; Normal
mode
0.3
1
12
ms
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
35 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.3 BOD static characteristics
Table 10. BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Vth
threshold voltage
interrupt level 1
Min
Typ
Max
Unit
assertion
-
2.22
-
V
de-assertion
-
2.35
-
V
assertion
-
2.52
-
V
de-assertion
-
2.66
-
V
assertion
-
2.80
-
V
de-assertion
-
2.90
-
V
assertion
-
1.46
-
V
de-assertion
-
1.63
-
V
interrupt level 2
interrupt level 3
reset level 0
reset level 1
assertion
-
2.06
-
V
de-assertion
-
2.15
-
V
assertion
-
2.35
-
V
de-assertion
-
2.43
-
V
assertion
-
2.63
-
V
de-assertion
-
2.71
-
V
reset level 2
reset level 3
[1]
Interrupt levels are selected by writing the level value to the BOD control register BODCTRL, see LPC11Cx
user manual.
9.4 Power consumption
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see LPC11Cx user manual):
• Configure all pins as GPIO with pull-up resistor disabled in the IOCONFIG block.
• Configure GPIO pins as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
36 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf390
12
IDD
(mA)
48 MHz(2)
8
36 MHz(2)
24 MHz(2)
4
12 MHz(1)
0
1.8
2.4
3.0
3.6
VDD (V)
Conditions: Tamb = 25 C; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; pin CAN_RXD pulled LOW
externally.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 7.
Active mode: Typical supply current IDD versus supply voltage VDD for different
system clock frequencies
002aaf391
12
IDD
(mA)
48 MHz(2)
8
36 MHz(2)
24 MHz(2)
4
0
−40
12 MHz(1)
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; active mode entered executing code while(1){} from flash; all
peripherals disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral
clocks disabled; internal pull-up resistors disabled; BOD disabled; pin CAN_RXD pulled LOW
externally.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 8.
LPC11CX2_CX4
Product data sheet
Active mode: Typical supply current IDD versus temperature for different system
clock frequencies
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
37 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf392
8
IDD
(mA)
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; sleep mode entered from flash; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks disabled; internal
pull-up resistors disabled; BOD disabled; pin CAN_RXD pulled LOW externally.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 9.
Sleep mode: Typical supply current IDD versus temperature for different system
clock frequencies
002aaf394
40
IDD
(μA)
30
3.6 V
3.3 V
2.0 V
1.8 V
20
10
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks disabled in the PDSLEEPCFG register
(PDSLEEPCFG = 0x0000 18FF); pin CAN_RXD pulled LOW externally.
Fig 10. Deep-sleep mode: Typical supply current IDD versus temperature for different
supply voltages VDD
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
38 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf457
0.8
IDD
(μA)
0.6
VDD = 3.6 V
3.3 V
2.0 V
1.8 V
0.4
0.2
0
−40
−15
10
35
60
85
temperature (°C)
Fig 11. Deep power-down mode: Typical supply current IDD versus temperature for
different supply voltages VDD
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
39 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.5 Peripheral power consumption
The supply current per peripheral is measured as the difference in supply current between
the peripheral block enabled and the peripheral block disabled in the SYSAHBCLKCFG
and PDRUNCFG (for analog blocks) registers. All other blocks are disabled in both
registers and no code is executed. Measured on a typical sample at Tamb = 25 C. Unless
noted otherwise, the system oscillator and PLL are running in both measurements.
The supply currents are shown for system clock frequencies of 12 MHz and 48 MHz.
Table 11.
Power consumption for individual analog and digital blocks
Peripheral
LPC11CX2_CX4
Product data sheet
Typical supply current in
mA
Notes
n/a
12 MHz
48 MHz
IRC
0.27
-
-
System oscillator running; PLL off;
independent of main clock frequency.
System oscillator
at 12 MHz
0.22
-
-
IRC running; PLL off; independent of main
clock frequency.
Watchdog
oscillator at
500 kHz/2
0.004
-
-
System oscillator running; PLL off;
independent of main clock frequency.
BOD
0.051
-
-
Independent of main clock frequency.
Main PLL
-
0.21
-
ADC
-
0.08
0.29
CLKOUT
-
0.12
0.47
CT16B0
-
0.02
0.06
CT16B1
-
0.02
0.06
CT32B0
-
0.02
0.07
CT32B1
-
0.02
0.06
GPIO
-
0.23
0.88
IOCONFIG
-
0.03
0.10
I2C
-
0.04
0.13
ROM
-
0.04
0.15
SPI0
-
0.12
0.45
SPI1
-
0.12
0.45
UART
-
0.22
0.82
C_CAN
-
0.03
0.1
WDT
-
0.02
0.06
Main clock divided by 4 in the CLKOUTDIV
register.
GPIO pins configured as outputs and set to
LOW. Direction and pin state are maintained if
the GPIO is disabled in the SYSAHBCLKCFG
register.
Main clock selected as clock source for the
WDT.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
40 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.6 Electrical pin characteristics
002aae990
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
10
20
30
40
50
60
IOH (mA)
Conditions: VDD = 3.3 V; on pin PIO0_7.
Fig 12. High-drive output: Typical HIGH-level output voltage VOH versus HIGH-level
output current IOH.
002aaf019
60
T = 85 °C
25 °C
−40 °C
IOL
(mA)
40
20
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; on pins PIO0_4 and PIO0_5.
Fig 13. I2C-bus pins (high current sink): Typical LOW-level output current IOL versus
LOW-level output voltage VOL
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
41 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae991
15
IOL
(mA)
T = 85 °C
25 °C
−40 °C
10
5
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; standard port pins and PIO0_7.
Fig 14. Typical LOW-level output current IOL versus LOW-level output voltage VOL
002aae992
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
8
16
24
IOH (mA)
Conditions: VDD = 3.3 V; standard port pins.
Fig 15. Typical HIGH-level output voltage VOH versus HIGH-level output source current
IOH
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
42 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae988
10
Ipu
(μA)
−10
−30
T = 85 °C
25 °C
−40 °C
−50
−70
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 16. Typical pull-up current Ipu versus input voltage VI
002aae989
80
T = 85 °C
25 °C
−40 °C
Ipd
(μA)
60
40
20
0
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 17. Typical pull-down current Ipd versus input voltage VI
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
43 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10. Dynamic characteristics
10.1 Flash memory
Table 12. Flash characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
[1]
Nendu
endurance
tret
retention time
ter
erase time
tprog
programming
time
Typ
Max
Unit
10000
100000
-
cycles
powered
10
-
-
years
unpowered
20
-
-
years
sector or multiple
consecutive
sectors
95
100
105
ms
0.95
1
1.05
ms
[2]
[1]
Number of program/erase cycles.
[2]
Programming times are given for writing 256 bytes from RAM to the flash. Data must be written to the flash
in blocks of 256 bytes.
10.2 External clock
Table 13. Dynamic characteristic: external clock
Tamb = 40 C to +85 C; VDD over specified ranges.[1]
Min
Typ[2]
Max
Unit
oscillator frequency
1
-
25
MHz
Tcy(clk)
clock cycle time
40
-
1000
ns
tCHCX
clock HIGH time
Tcy(clk) 0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk) 0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
Symbol
Parameter
fosc
Conditions
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 18. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
44 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.3 Internal oscillators
Table 14. Dynamic characteristic: internal oscillators
Tamb = 40 C to +85 C; 2.7 V VDD 3.6 V.[1]
Symbol
Parameter
Conditions
fosc(RC)
internal RC oscillator frequency -
Min
Typ[2]
Max
Unit
11.88
12
12.12
MHz
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
002aaf403
12.15
f
(MHz)
VDD = 3.6 V
3.3 V
3.0 V
2.7 V
2.4 V
2.0 V
12.05
11.95
11.85
−40
−15
10
35
60
85
temperature (°C)
Conditions: Frequency values are typical values. 12 MHz 1 % accuracy is guaranteed for
2.7 V VDD 3.6 V and Tamb = 40 C to +85 C. Variations between parts may cause the IRC to
fall outside the 12 MHz 1 % accuracy specification for voltages below 2.7 V.
Fig 19. Internal RC oscillator frequency versus temperature
Table 15.
Dynamic characteristics: Watchdog oscillator
Min
Typ[1]
Max
Unit
internal oscillator DIVSEL = 0x1F, FREQSEL = 0x1
frequency
in the WDTOSCCTRL register;
[2][3]
-
7.8
-
kHz
DIVSEL = 0x00, FREQSEL = 0xF
in the WDTOSCCTRL register
[2][3]
-
1700
-
kHz
Symbol Parameter
fosc(int)
LPC11CX2_CX4
Product data sheet
Conditions
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[2]
The typical frequency spread over processing and temperature (Tamb = 40 C to +85 C) is 40 %.
[3]
See the LPC11Cx user manual.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
45 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.4 I/O pins
Table 16. Dynamic characteristic: I/O pins[1]
Tamb = 40 C to +85 C; 3.0 V VDD 3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
pin
configured as
output
3.0
-
5.0
ns
tf
fall time
pin
configured as
output
2.5
-
5.0
ns
[1]
Applies to standard port pins and RESET pin.
10.5 I2C-bus
Table 17. Dynamic characteristic: I2C-bus pins[1]
Tamb = 40 C to +85 C.[2]
Symbol
Parameter
Conditions
Min
Max
Unit
fSCL
SCL clock
frequency
Standard-mode
0
100
kHz
Fast-mode
0
400
kHz
Fast-mode Plus
0
1
MHz
of both SDA and
SCL signals
-
300
ns
20 + 0.1 Cb
300
ns
[4][5][6][7]
fall time
tf
Standard-mode
Fast-mode
Fast-mode Plus
tLOW
tHIGH
tHD;DAT
tSU;DAT
[1]
LPC11CX2_CX4
Product data sheet
LOW period of
the SCL clock
HIGH period of
the SCL clock
data hold time
data set-up
time
[3][4][8]
[9][10]
-
120
ns
Standard-mode
4.7
-
s
Fast-mode
1.3
-
s
Fast-mode Plus
0.5
-
s
Standard-mode
4.0
-
s
Fast-mode
0.6
-
s
Fast-mode Plus
0.26
-
s
Standard-mode
0
-
s
Fast-mode
0
-
s
Fast-mode Plus
0
-
s
Standard-mode
250
-
ns
Fast-mode
100
-
ns
Fast-mode Plus
50
-
ns
See the I2C-bus specification UM10204 for details.
[2]
Parameters are valid over operating temperature range unless otherwise specified.
[3]
tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission
and the acknowledge.
[4]
A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the
VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.
[5]
Cb = total capacitance of one bus line in pF.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
46 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
[6]
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA
output stage tf is specified at 250 ns. This allows series protection resistors to be connected in between the
SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf.
[7]
In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors
are used, designers should allow for this when considering bus timing.
[8]
The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than
the maximum of tVD;DAT or tVD;ACK by a transition time (see UM10204). This maximum must only be met if
the device does not stretch the LOW period (tLOW) of the SCL signal. If the clock stretches the SCL, the
data must be valid by the set-up time before it releases the clock.
[9]
tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in
transmission and the acknowledge.
[10] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement tSU;DAT =
250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period
of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-mode I2C-bus
specification) before the SCL line is released. Also the acknowledge timing must meet this set-up time.
tf
SDA
tSU;DAT
70 %
30 %
70 %
30 %
tHD;DAT
tf
70 %
30 %
SCL
tVD;DAT
tHIGH
70 %
30 %
70 %
30 %
70 %
30 %
tLOW
S
1 / fSCL
002aaf425
Fig 20. I2C-bus pins clock timing
10.6 SPI interfaces
Table 18.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
-
-
ns
-
-
SPI master (in SPI mode)
Tcy(clk)
tDS
full-duplex mode
[1]
50
when only transmitting
[1]
40
in SPI mode
[2]
15
2.0 V VDD < 2.4 V
[2]
20
1.8 V VDD < 2.0 V
[2]
24
-
-
ns
in SPI mode
[2]
0
-
-
ns
data output valid time in SPI mode
[2]
-
-
10
ns
data output hold time in SPI mode
[2]
0
-
-
ns
20
-
-
ns
clock cycle time
data set-up time
ns
ns
2.4 V VDD 3.6 V
tDH
tv(Q)
th(Q)
data hold time
ns
SPI slave (in SPI mode)
Tcy(PCLK)
PCLK cycle time
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
47 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 18.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tDS
data set-up time
in SPI mode
[3][4]
0
-
-
ns
tDH
data hold time
in SPI mode
[3][4]
3 Tcy(PCLK) + 4
-
-
ns
data output valid time in SPI mode
[3][4]
-
-
3 Tcy(PCLK) + 11
ns
data output hold time in SPI mode
[3][4]
-
-
2 Tcy(PCLK) + 5
ns
tv(Q)
th(Q)
[1]
Tcy(clk) = (SSPCLKDIV (1 + SCR) CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SPI peripheral clock divider (SSPCLKDIV), the SPI SCR parameter (specified in the SSP0CR0 register),
and the SPI CPSDVSR parameter (specified in the SPI clock prescale register).
[2]
Tamb = 40 C to 85 C.
[3]
Tcy(clk) = 12 Tcy(PCLK).
[4]
Tamb = 25 C; for normal voltage supply range: VDD = 3.3 V.
Tcy(clk)
tclk(H)
tclk(L)
SCK (CPOL = 0)
SCK (CPOL = 1)
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDS
DATA VALID
MISO
tDH
DATA VALID
tv(Q)
MOSI
DATA VALID
th(Q)
DATA VALID
tDH
tDS
MISO
DATA VALID
CPHA = 1
CPHA = 0
DATA VALID
002aae829
Pin names SCK, MISO, and MOSI refer to pins for both SPI peripherals, SPI0 and SPI1.
Fig 21. SPI master timing in SPI mode
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
48 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Tcy(clk)
tclk(H)
tclk(L)
tDS
tDH
SCK (CPOL = 0)
SCK (CPOL = 1)
MOSI
DATA VALID
DATA VALID
tv(Q)
MISO
th(Q)
DATA VALID
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
DATA VALID
CPHA = 1
DATA VALID
th(Q)
CPHA = 0
DATA VALID
002aae830
Pin names SCK, MISO, and MOSI refer to pins for both SPI peripherals, SPI0 and SPI1.
Fig 22. SPI slave timing in SPI mode
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
49 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11. Application information
11.1 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in Table 7:
• The ADC input trace must be short and as close as possible to the LPC11Cx2/Cx4
chip.
• The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
• Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
• To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mv (RMS) is needed.
LPC1xxx
XTALIN
Ci
100 pF
Cg
002aae788
Fig 23. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure 23), with an amplitude between 200 mv (RMS) and 1000 mv (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in Figure 24 and in
Table 19 and Table 20. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances CX1 and CX2 need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, CL and
RS). Capacitance CP in Figure 24 represents the parallel package capacitance and should
not be larger than 7 pF. Parameters FOSC, CL, RS and CP are supplied by the crystal
manufacturer (see Table 19).
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
50 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
LPC1xxx
L
XTALIN
XTALOUT
=
CL
CP
XTAL
RS
CX2
CX1
002aaf424
Fig 24. Oscillator modes and models: oscillation mode of operation and external crystal
model used for CX1/CX2 evaluation
Table 19.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) low frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
1 MHz - 5 MHz
10 pF
< 300
18 pF, 18 pF
20 pF
< 300
39 pF, 39 pF
5 MHz - 10 MHz
10 MHz - 15 MHz
15 MHz - 20 MHz
Table 20.
30 pF
< 300
57 pF, 57 pF
10 pF
< 300
18 pF, 18 pF
20 pF
< 200
39 pF, 39 pF
30 pF
< 100
57 pF, 57 pF
10 pF
< 160
18 pF, 18 pF
20 pF
< 60
39 pF, 39 pF
10 pF
< 80
18 pF, 18 pF
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) high frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
15 MHz - 20 MHz
10 pF
< 180
18 pF, 18 pF
20 pF
< 100
39 pF, 39 pF
20 MHz - 25 MHz
10 pF
< 160
18 pF, 18 pF
20 pF
< 80
39 pF, 39 pF
11.3 XTAL Printed Circuit Board (PCB) layout guidelines
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors Cx1, Cx2, and Cx3 in case of
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plain. Loops must be made as small as possible in
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
51 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
order to keep the noise coupled in via the PCB as small as possible. Also parasitics
should stay as small as possible. Values of Cx1 and Cx2 should be chosen smaller
accordingly to the increase in parasitics of the PCB layout.
11.4 Standard I/O pad configuration
Figure 25 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
Digital output driver
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
VDD
ESD
output enable
pin configured
as digital output
driver
output
PIN
ESD
VDD
VSS
weak
pull-up
pull-up enable
pin configured
as digital input
weak
pull-down
repeater mode
enable
pull-down enable
data input
select analog input
pin configured
as analog input
analog input
002aaf304
Fig 25. Standard I/O pad configuration
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
52 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11.5 Reset pad configuration
VDD
VDD
VDD
Rpu
reset
ESD
20 ns RC
GLITCH FILTER
PIN
ESD
VSS
002aaf274
Fig 26. Reset pad configuration
11.6 C_CAN with external transceiver (LPC11C12/C14 only)
BAT
3V
5V
VIO
VCC
CANH
CANH
S
TJF1051
TXD
RXD
CANL
CANL
GND
LPC11C12/C14
PIOx_y
CAN_TXD
CAN_RXD
002aaf911
Fig 27. Connecting the C_CAN to an external transceiver (LPC11C12/C14)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
53 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11.7 C_CAN with on-chip, high-speed transceiver (LPC11C22/C24 only)
VDD
3V
5V
VDD_CAN
VCC
VDD
LPC11C22/C24
CANH
CAN_TXD
CANH
CAN
HIGH-SPEED
TRANSCEIVER
CANL
C_CAN
CAN_RXD
CANL
STD
GND
002aaf910
Fig 28. Connecting the CAN high-speed transceiver to the CAN bus (LPC11C22/C24)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
54 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
12. Package outline
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
c
y
X
36
25
A
37
24
ZE
e
E HE
A A2
(A 3)
A1
w M
θ
bp
pin 1 index
Lp
L
13
48
detail X
12
1
ZD
e
v M A
w M
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HD
HE
L
Lp
v
w
y
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
7.1
6.9
7.1
6.9
0.5
9.15
8.85
9.15
8.85
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
θ
0.95
0.55
7o
o
0
0.95
0.55
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT313-2
136E05
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 29. Package outline SOT313-2 (LQFP48)
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
55 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
13. Soldering
Footprint information for reflow soldering of LQFP48 package
SOT313-2
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
P2
0.500
0.560
Ax
Ay
10.350 10.350
Bx
By
C
D1
D2
Gx
7.350
7.350
1.500
0.280
0.500
7.500
Gy
Hx
Hy
7.500 10.650 10.650
sot313-2_fr
Fig 30. Reflow soldering of the LQFP48 package
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
56 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
14. Abbreviations
Table 21.
LPC11CX2_CX4
Product data sheet
Abbreviations
Acronym
Description
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
APB
Advanced Peripheral Bus
API
Application Programming Interface
BOD
BrownOut Detection
CAN
Controller Area Network
GPIO
General Purpose Input/Output
PLL
Phase-Locked Loop
RC
Resistor-Capacitor
SDO
Service Data Object
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SSP
Synchronous Serial Port
UART
Universal Asynchronous Receiver/Transmitter
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
57 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
15. Revision history
Table 22.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
LPC11CX2_CX4 v.3.1
20130515
Product data sheet
-
LPC11CX2_CX4 v.3
Modifications:
•
•
Table 3 and Table 4: Added “5 V tolerant pad” to RESET/PIO0_0 table note.
Table 5:
– Added Table note 2.
– Corrected VDD min and max.
•
•
LPC11CX2_CX4 v.3
Modifications:
LPC11CX2_CX4 v.2
Modifications:
LPC11C12_C14 v.1
LPC11CX2_CX4
Product data sheet
Table 8: Added Table note 1.
Table 10: Removed BOD interrupt level 0.
20110627
Product data sheet
-
•
I2C-bus
•
•
•
•
•
•
•
•
•
Parameter Vx added to Table 5 “Limiting values”.
LPC11C12_C14 v.2
pins configured as standard mode pins, parameter IOL changed to 3.5 mA
(minimum) for 2.0 V VDD 3.6 V.
C_CAN power consumption data added to Table 11.
ADC sampling frequency corrected in Table 7 (Table note 7).
Reflow soldering footprint drawing added (Section 13).
Pull-up level specified in Table 3 and Table 4.
Parameter Tcy(clk) corrected on Table 18.
Condition for parameter Tstg in Table 5 updated.
Table note 5 of Table 5 updated.
Table 18 T~cy(clk) condition changed from “when only receiving” to “full-duplex mode”
20101203
Product data sheet
-
LPC11C12_C14 v.1
•
•
•
•
Parts LPC11C22 and LPC11C24 added.
•
Application diagram for connecting the C_CAN to an external transceiver added
(Section 11.6).
•
•
•
•
•
Application diagram for high-speed, on-chip CAN transceiver added (Section 11.7).
Pin description for parts LPC11C22 and LPC11C24 added (Table 4).
Static characteristics for CAN transceiver added (Table 8).
Description of high-speed, on-chip CAN transceiver added (LPC11C22/C24). See
Section 7.11.2.
Typical value for parameter Nendu added in Table 12 “Flash characteristics”.
Description of RESET and WAKEKUP pins updated in Table 3.
PLL output frequency limited to < 100 MHz in Section 7.16.2 “System PLL”.
Parameter Vhys for I2C bus pins: typical value corrected Vhys = 0.05VDD in Table 6.
20100921
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
-
© NXP B.V. 2013. All rights reserved.
58 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
LPC11CX2_CX4
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
59 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
60 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
18. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
4.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7
7
Functional description . . . . . . . . . . . . . . . . . . 15
7.1
ARM Cortex-M0 processor . . . . . . . . . . . . . . . 15
7.2
On-chip flash program memory . . . . . . . . . . . 15
7.3
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 15
7.4
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.5
Nested Vectored Interrupt Controller (NVIC) . 16
7.5.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5.2
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 17
7.6
IOCONFIG block . . . . . . . . . . . . . . . . . . . . . . 17
7.7
Fast general purpose parallel I/O . . . . . . . . . . 17
7.7.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.8
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.8.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.9
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 18
7.9.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.10
I2C-bus serial I/O controller . . . . . . . . . . . . . . 18
7.10.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.11
C_CAN controller . . . . . . . . . . . . . . . . . . . . . . 19
7.11.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.11.2
On-chip, high-speed CAN transceiver . . . . . . 20
7.11.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.11.2.2 Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.11.2.3 Silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.11.2.4 Undervoltage protection . . . . . . . . . . . . . . . . . 20
7.11.2.5 Thermal protection . . . . . . . . . . . . . . . . . . . . . 20
7.11.2.6 Time-out function . . . . . . . . . . . . . . . . . . . . . . 21
7.12
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.12.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.13
General purpose external event
counter/timers . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.13.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.14
System tick timer . . . . . . . . . . . . . . . . . . . . . . 22
7.15
Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . 22
7.15.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.16
Clocking and power control . . . . . . . . . . . . . . 22
7.16.1
Crystal oscillators . . . . . . . . . . . . . . . . . . . . . . 22
7.16.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . . 23
7.16.1.2 System oscillator . . . . . . . . . . . . . . . . . . . . . . 23
7.16.1.3 Watchdog oscillator . . . . . . . . . . . . . . . . . . . .
7.16.2
System PLL . . . . . . . . . . . . . . . . . . . . . . . . . .
7.16.3
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . .
7.16.4
Wake-up process . . . . . . . . . . . . . . . . . . . . . .
7.16.5
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
7.16.5.1 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . .
7.16.5.2 Deep-sleep mode. . . . . . . . . . . . . . . . . . . . . .
7.16.5.3 Deep power-down mode . . . . . . . . . . . . . . . .
7.17
System control . . . . . . . . . . . . . . . . . . . . . . . .
7.17.1
Start logic . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.3
Brownout detection . . . . . . . . . . . . . . . . . . . .
7.17.4
Code security (Code Read Protection - CRP)
7.17.5
Bootloader . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.6
APB interface . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.7
AHBLite . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.8
External interrupt inputs . . . . . . . . . . . . . . . . .
7.18
Emulation and debugging . . . . . . . . . . . . . . .
8
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
9
Static characteristics . . . . . . . . . . . . . . . . . . .
9.1
ADC characteristics . . . . . . . . . . . . . . . . . . . .
9.2
C_CAN on-chip, high-speed transceiver
characteristics . . . . . . . . . . . . . . . . . . . . . . . .
9.3
BOD static characteristics . . . . . . . . . . . . . . .
9.4
Power consumption . . . . . . . . . . . . . . . . . . .
9.5
Peripheral power consumption . . . . . . . . . . .
9.6
Electrical pin characteristics. . . . . . . . . . . . . .
10
Dynamic characteristics. . . . . . . . . . . . . . . . .
10.1
Flash memory . . . . . . . . . . . . . . . . . . . . . . . .
10.2
External clock. . . . . . . . . . . . . . . . . . . . . . . . .
10.3
Internal oscillators . . . . . . . . . . . . . . . . . . . . .
10.4
I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.5
I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6
SPI interfaces. . . . . . . . . . . . . . . . . . . . . . . . .
11
Application information . . . . . . . . . . . . . . . . .
11.1
ADC usage notes. . . . . . . . . . . . . . . . . . . . . .
11.2
XTAL input . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3
XTAL Printed Circuit Board (PCB) layout
guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4
Standard I/O pad configuration . . . . . . . . . . .
11.5
Reset pad configuration . . . . . . . . . . . . . . . . .
11.6
C_CAN with external transceiver
(LPC11C12/C14 only) . . . . . . . . . . . . . . . . . .
11.7
C_CAN with on-chip, high-speed transceiver
(LPC11C22/C24 only) . . . . . . . . . . . . . . . . . .
12
Package outline. . . . . . . . . . . . . . . . . . . . . . . .
13
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
24
24
24
24
25
25
25
25
25
25
26
26
27
27
27
27
28
29
32
34
36
36
40
41
44
44
44
45
46
46
47
50
50
50
51
52
53
53
54
55
56
continued >>
LPC11CX2_CX4
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3.1 — 15 May 2013
© NXP B.V. 2013. All rights reserved.
61 of 62
LPC11Cx2/Cx4
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
14
15
16
16.1
16.2
16.3
16.4
17
18
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . . .
Legal information. . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information. . . . . . . . . . . . . . . . . . . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
58
59
59
59
59
60
60
61
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2013.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 15 May 2013
Document identifier: LPC11CX2_CX4