PHILIPS LPC1111

LPC1111/12/13/14
32-bit ARM Cortex-M0 microcontroller; up to 32 kB flash and
8 kB SRAM
Rev. 5 — 22 June 2011
Product data sheet
1. General description
The LPC1111/12/13/14 are a ARM Cortex-M0 based, low-cost 32-bit MCU family,
designed for 8/16-bit microcontroller applications, offering performance, low power, simple
instruction set and memory addressing together with reduced code size compared to
existing 8/16-bit architectures.
The LPC1111/12/13/14 operate at CPU frequencies of up to 50 MHz.
The peripheral complement of the LPC1111/12/13/14 includes up to 32 kB of flash
memory, up to 8 kB of data memory, one Fast-mode Plus I2C-bus interface, one
RS-485/EIA-485 UART, up to two SPI interfaces with SSP features, four general purpose
counter/timers, a 10-bit ADC, and up to 42 general purpose I/O pins.
Remark: The LPC1111/12/13/14 series consists of the LPC1100 series (parts
LPC111x/101/201/301) and the LPC1100L series (parts LPC111x/102/202/302). The
LPC1100L includes the power profiles, a windowed watchdog timer, and a configurable
open-drain mode.
2. Features and benefits
 System:
 ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
 ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
 Serial Wire Debug.
 System tick timer.
 Memory:
 32 kB (LPC1114), 24 kB (LPC1113), 16 kB (LPC1112), or 8 kB (LPC1111) on-chip
flash programming memory.
 8 kB, 4 kB, or 2 kB SRAM.
 In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software.
 Digital peripherals:
 Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
resistors. In addition, a configurable open-drain mode is supported on the
LPC111x/102/202/302.
 GPIO pins can be used as edge and level sensitive interrupt sources.
 High-current output driver (20 mA) on one pin.
 High-current sink drivers (20 mA) on two I2C-bus pins in Fast-mode Plus.
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller







 Four general purpose counter/timers with a total of four capture inputs and 13
match outputs.
 Programmable WatchDog Timer (WDT).
 Programmable windowed WDT on LPC111x/102/202/302 only.
Analog peripherals:
 10-bit ADC with input multiplexing among 8 pins.
Serial interfaces:
 UART with fractional baud rate generation, internal FIFO, and RS-485 support.
 Two SPI controllers with SSP features and with FIFO and multi-protocol
capabilities (second SPI on LQFP48 package only).
 I2C-bus interface supporting full I2C-bus specification and Fast-mode Plus with a
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
Clock generation:
 12 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used
as a system clock.
 Crystal oscillator with an operating range of 1 MHz to 25 MHz.
 Programmable watchdog oscillator with a frequency range of 7.8 kHz to 1.8 MHz.
 PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from the system oscillator or the internal RC
oscillator.
 Clock output function with divider that can reflect the system oscillator clock, IRC
clock, CPU clock, and the Watchdog clock.
Power control:
 Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep, Deep-sleep, and Deep power-down modes.
 Power profiles residing in boot ROM allowing to optimize performance and
minimize power consumption for any given application through one simple function
call. (LPC1100L series, on LPC111x/102/202/302 only.)
 Three reduced power modes: Sleep, Deep-sleep, and Deep power-down.
 Processor wake-up from Deep-sleep mode via a dedicated start logic using up to
13 of the functional pins.
 Power-On Reset (POR).
 Brownout detect with four separate thresholds for interrupt and forced reset.
Unique device serial number for identification.
Single power supply (1.8 V to 3.6 V).
Available as 48-pin LQFP package and 33-pin HVQFN package.
3. Applications
 eMetering
 Alarm systems
LPC1111_12_13_14
Product data sheet
 Lighting
 White goods
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
2 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC1111FHN33/101
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1111FHN33/102
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1111FHN33/201
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1111FHN33/202
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1112FHN33/101
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1112FHN33/102
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1112FHN33/201
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1112FHN33/202
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1113FHN33/201
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1113FHN33/202
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1113FHN33/301
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1113FHN33/302
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1114FHN33/201
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1114FHN33/202
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1114FHN33/301
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1114FHN33/302
HVQFN33
HVQFN: plastic thermal enhanced very thin quad flat package; no
leads; 33 terminals; body 7  7  0.85 mm
n/a
LPC1113FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7  7  SOT313-2
1.4 mm
LPC1113FBD48/302
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7  7  SOT313-2
1.4 mm
LPC1114FBD48/301
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7  7  SOT313-2
1.4 mm
LPC1114FBD48/302
LQFP48
LQFP48: plastic low profile quad flat package; 48 leads; body 7  7  SOT313-2
1.4 mm
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
3 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
4.1 Ordering options
Table 2.
Ordering options
Series
Flash
Total
SRAM
Power
profiles
UART I2C/
SPI ADC
Package
RS-485 Fast+
channels
LPC1111FHN33/101
LPC1100
8 kB
2 kB
no
1
1
1
8
HVQFN33
LPC1111FHN33/102
LPC1100L
8 kB
2 kB
yes
1
1
1
8
HVQFN33
LPC1111FHN33/201
LPC1100
8 kB
4 kB
no
1
1
1
8
HVQFN33
LPC1111FHN33/202
LPC1100L
8 kB
4 kB
yes
1
1
1
8
HVQFN33
LPC1112FHN33/101
LPC1100
16 kB
2 kB
no
1
1
1
8
HVQFN33
LPC1112FHN33/102
LPC1100L
16 kB
2 kB
yes
1
1
1
8
HVQFN33
Type number
LPC1111
LPC1112
LPC1112FHN33/201
LPC1100
16 kB
4 kB
no
1
1
1
8
HVQFN33
LPC1112FHN33/202
LPC1100L
16 kB
4 kB
yes
1
1
1
8
HVQFN33
LPC1113FHN33/201
LPC1100
24 kB
4 kB
no
1
1
1
8
HVQFN33
LPC1113FHN33/202
LPC1100L
24 kB
4 kB
yes
1
1
1
8
HVQFN33
LPC1113FHN33/301
LPC1100
24 kB
8 kB
no
1
1
1
8
HVQFN33
LPC1113FHN33/302
LPC1100L
24 kB
8 kB
yes
1
1
1
8
HVQFN33
LPC1113FBD48/301
LPC1100
24 kB
8 kB
no
1
1
2
8
LQFP48
LPC1113FBD48/302
LPC1100L
24 kB
8 kB
yes
1
1
2
8
LQFP48
LPC1114FHN33/201
LPC1100
32 kB
4 kB
no
1
1
1
8
HVQFN33
LPC1114FHN33/202
LPC1100L
32 kB
4 kB
yes
1
1
1
8
HVQFN33
LPC1113
LPC1114
LPC1114FHN33/301
LPC1100
32 kB
8 kB
no
1
1
1
8
HVQFN33
LPC1114FHN33/302
LPC1100L
32 kB
8 kB
yes
1
1
1
8
HVQFN33
LPC1114FBD48/301
LPC1100
32 kB
8 kB
no
1
1
2
8
LQFP48
LPC1114FBD48/302
LPC1100L
32 kB
8 kB
yes
1
1
2
8
LQFP48
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
4 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
5. Block diagram
XTALIN
XTALOUT
RESET
SWD
LPC1111/12/13/14
IRC
TEST/DEBUG
INTERFACE
CLOCK
GENERATION,
POWER CONTROL,
SYSTEM
FUNCTIONS
POR
ARM
CORTEX-M0
system bus
clocks and
controls
FLASH
8/16/24/32 kB
slave
GPIO ports
PIO0/1/2/3
HIGH-SPEED
GPIO
CLKOUT
SRAM
2/4/8 kB
slave
ROM
slave
slave
AHB-LITE BUS
slave
AHB TO APB
BRIDGE
RXD
TXD
DTR, DSR(1), CTS,
DCD(1), RI(1), RTS
CT32B0_MAT[3:0]
CT32B0_CAP0
CT32B1_MAT[3:0]
CT32B1_CAP0
CT16B0_MAT[2:0]
CT16B0_CAP0
CT16B1_MAT[1:0]
CT16B1_CAP0
UART
AD[7:0]
10-bit ADC
SPI0
SCK0, SSEL0
MISO0, MOSI0
SPI1(1)
SCK1, SSEL1
MISO1, MOSI1
32-bit COUNTER/TIMER 0
32-bit COUNTER/TIMER 1
SCL
SDA
I2C-BUS
16-bit COUNTER/TIMER 0
WDT
16-bit COUNTER/TIMER 1
IOCONFIG
SYSTEM CONTROL
PMU
002aae696
(1) LQFP48 packages only.
Fig 1.
LPC1111/12/13/14 block diagram
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
5 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6. Pinning information
37 PIO3_1/DSR
38 PIO2_3/RI/MOSI1
39 SWDIO/PIO1_3/AD4/CT32B1_MAT2
40 PIO1_4/AD5/CT32B1_MAT3/WAKEUP
41 VSS
42 PIO1_11/AD7
43 PIO3_2/DCD
44 VDD
45 PIO1_5/RTS/CT32B0_CAP0
46 PIO1_6/RXD/CT32B0_MAT0
PIO2_6
1
36 PIO3_0/DTR
PIO2_0/DTR/SSEL1
2
35 R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
3
34 R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
4
33 R/PIO1_0/AD1/CT32B1_CAP0
VSS
5
XTALIN
6
XTALOUT
7
VDD
8
PIO1_8/CT16B1_CAP0
9
28 PIO0_9/MOSI0/CT16B0_MAT1
PIO0_2/SSEL0/CT16B0_CAP0 10
27 PIO0_8/MISO0/CT16B0_MAT0
32 R/PIO0_11/AD0/CT32B0_MAT3
LPC1113FBD48/301
LPC1113FBD48/302
LPC1114FBD48/301
LPC1114FBD48/302
31 PIO2_11/SCK0
30 PIO1_10/AD6/CT16B1_MAT1
29 SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO2_9 24
PIO0_7/CTS 23
PIO0_6/SCK0 22
PIO3_5 21
PIO2_5 20
PIO2_4 19
PIO3_4 18
PIO1_9/CT16B1_MAT0 17
PIO0_5/SDA 16
25 PIO2_10
PIO0_4/SCL 15
26 PIO2_2/DCD/MISO1
PIO2_8 12
PIO0_3 14
PIO2_7 11
PIO2_1/DSR/SCK1 13
Fig 2.
47 PIO1_7/TXD/CT32B0_MAT1
48 PIO3_3/RI
6.1 Pinning
002aae697
Pin configuration LQFP48 package
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
6 of 64
LPC1111/12/13/14
NXP Semiconductors
VDD
PIO3_2
PIO1_11/AD7
PIO1_4/AD5/CT32B1_MAT3/WAKEUP
SWDIO/PIO1_3/AD4/CT32B1_MAT2
27
26
25
PIO1_5/RTS/CT32B0_CAP0
28
PIO1_6/RXD/CT32B0_MAT0
30
29
PIO1_7/TXD/CT32B0_MAT1
31
terminal 1
index area
32
32-bit ARM Cortex-M0 microcontroller
PIO2_0/DTR
1
24
R/PIO1_2/AD3/CT32B1_MAT1
RESET/PIO0_0
2
23
R/PIO1_1/AD2/CT32B1_MAT0
PIO0_1/CLKOUT/CT32B0_MAT2
3
22
R/PIO1_0/AD1/CT32B1_CAP0
XTALIN
4
21
R/PIO0_11/AD0/CT32B0_MAT3
XTALOUT
5
20
PIO1_10/AD6/CT16B1_MAT1
VDD
6
19
SWCLK/PIO0_10/SCK0/CT16B0_MAT2
PIO1_8/CT16B1_CAP0
7
18
PIO0_9/MOSI0/CT16B0_MAT1
PIO0_2/SSEL0/CT16B0_CAP0
8
17
PIO0_8/MISO0/CT16B0_MAT0
9
10
11
12
13
14
15
16
PIO0_3
PIO0_4/SCL
PIO0_5/SDA
PIO1_9/CT16B1_MAT0
PIO3_4
PIO3_5
PIO0_6/SCK0
PIO0_7/CTS
33 VSS
002aae698
Transparent top view
Fig 3.
Pin configuration HVQFN33 package
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
7 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
6.2 Pin description
Table 3.
LPC1113/14 pin description table (LQFP48 package)
Symbol
Pin
Start
logic
input
PIO0_0 to PIO0_11
RESET/PIO0_0
PIO0_1/CLKOUT/
CT32B0_MAT2
Type
Reset Description
state
[1]
I/O
3[2]
4[3]
yes
yes
Port 0 — Port 0 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 0 pins
depends on the function selected through the IOCONFIG
register block.
I
I; PU
RESET — External reset input with 20 ns glitch filter. A
LOW-going pulse as short as 50 ns on this pin resets the
device, causing I/O ports and peripherals to take on their default
states, and processor execution to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns
glitch filter.
I/O
I; PU
PIO0_1 — General purpose digital input/output pin. A LOW
level on this pin during reset starts the ISP command handler.
O
-
CLKOUT — Clockout pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
I/O
I; PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave Select for SPI0.
PIO0_2/SSEL0/
CT16B0_CAP0
10[3]
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
PIO0_3
14[3]
yes
I/O
I; PU
PIO0_3 — General purpose digital input/output pin.
PIO0_4/SCL
15[4]
yes
I/O
I; IA
PIO0_4 — General purpose digital input/output pin
(open-drain).
I/O
-
SCL — I2C-bus, open-drain clock input/output. High-current
sink only if I2C Fast-mode Plus is selected in the I/O
configuration register.
I/O
I; IA
PIO0_5 — General purpose digital input/output pin
(open-drain).
I/O
-
SDA — I2C-bus, open-drain data input/output. High-current sink
only if I2C Fast-mode Plus is selected in the I/O configuration
register.
PIO0_5/SDA
PIO0_6/SCK0
16[4]
22[3]
yes
yes
yes
PIO0_7/CTS
23[3]
yes
PIO0_8/MISO0/
CT16B0_MAT0
27[3]
yes
PIO0_9/MOSI0/
CT16B0_MAT1
28[3]
LPC1111_12_13_14
Product data sheet
yes
I/O
I; PU
PIO0_6 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I/O
I; PU
PIO0_7 — General purpose digital input/output pin
(high-current output driver).
I
-
CTS — Clear To Send input for UART.
I/O
I; PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SPI0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
I/O
I; PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SPI0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
8 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC1113/14 pin description table (LQFP48 package) …continued
Symbol
Pin
SWCLK/PIO0_10/
SCK0/
CT16B0_MAT2
29[3]
R/PIO0_11/
AD0/CT32B0_MAT3
32[5]
Start
logic
input
Type
yes
I
I; PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
I
I; PU
R — Reserved. Configure for an alternate function in the
IOCONFIG block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
yes
PIO1_0 to PIO1_11
R/PIO1_0/
AD1/CT32B1_CAP0
R/PIO1_1/
AD2/CT32B1_MAT0
R/PIO1_2/
AD3/CT32B1_MAT1
SWDIO/PIO1_3/
AD4/CT32B1_MAT2
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
LPC1111_12_13_14
Product data sheet
Reset Description
state
[1]
I/O
33[5]
34[5]
35[5]
39[5]
40[5]
yes
no
no
no
no
Port 1 — Port 1 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 1 pins
depends on the function selected through the IOCONFIG
register block.
I
I; PU
R — Reserved. Configure for an alternate function in the
IOCONFIG block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
O
I; PU
R — Reserved. Configure for an alternate function in the
IOCONFIG block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
I
I; PU
R — Reserved. Configure for an alternate function in the
IOCONFIG block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I; PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I; PU
PIO1_4 — General purpose digital input/output pin with 10 ns
glitch filter.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns
glitch filter. This pin must be pulled HIGH externally to enter
Deep power-down mode and pulled LOW to exit Deep
power-down mode. A LOW-going pulse as short as 50 ns
wakes up the part.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
9 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC1113/14 pin description table (LQFP48 package) …continued
Symbol
PIO1_5/RTS/
CT32B0_CAP0
Pin
45[3]
PIO1_6/RXD/
CT32B0_MAT0
46[3]
PIO1_7/TXD/
CT32B0_MAT1
47[3]
PIO1_8/
CT16B1_CAP0
9[3]
PIO1_9/
CT16B1_MAT0
17[3]
PIO1_10/AD6/
CT16B1_MAT1
30[5]
PIO1_11/AD7
42[5]
Start
logic
input
Type
no
I/O
no
no
no
no
no
no
PIO2_0 to PIO2_11
PIO2_0/DTR/SSEL1
PIO2_1/DSR/SCK1
PIO2_2/DCD/MISO1
PIO2_3/RI/MOSI1
Reset Description
state
[1]
I; PU
O
-
RTS — Request To Send output for UART.
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I; PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I/O
I; PU
PIO1_9 — General purpose digital input/output pin.
O
-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I/O
I; PU
PIO1_11 — General purpose digital input/output pin.
I
-
AD7 — A/D converter, input 7.
I/O
2[3]
13[3]
26[3]
38[3]
no
no
no
no
PIO1_5 — General purpose digital input/output pin.
Port 2 — Port 2 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 2 pins
depends on the function selected through the IOCONFIG
register block.
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
-
SSEL1 — Slave Select for SPI1.
I/O
I; PU
PIO2_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
-
SCK1 — Serial clock for SPI1.
I/O
I; PU
PIO2_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART.
I/O
-
MISO1 — Master In Slave Out for SPI1.
I/O
I; PU
PIO2_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
I/O
-
MOSI1 — Master Out Slave In for SPI1.
PIO2_4
19[3]
no
I/O
I; PU
PIO2_4 — General purpose digital input/output pin.
PIO2_5
20[3]
no
I/O
I; PU
PIO2_5 — General purpose digital input/output pin.
PIO2_6
1[3]
no
I/O
I; PU
PIO2_6 — General purpose digital input/output pin.
PIO2_7
11[3]
no
I/O
I; PU
PIO2_7 — General purpose digital input/output pin.
PIO2_8
12[3]
no
I/O
I; PU
PIO2_8 — General purpose digital input/output pin.
PIO2_9
24[3]
no
I/O
I; PU
PIO2_9 — General purpose digital input/output pin.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
10 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 3.
LPC1113/14 pin description table (LQFP48 package) …continued
Symbol
Pin
Start
logic
input
Type
I/O
PIO2_10
25[3]
no
PIO2_11/SCK0
31[3]
no
PIO3_0 to PIO3_5
Reset Description
state
[1]
I; PU
PIO2_10 — General purpose digital input/output pin.
I/O
I; PU
PIO2_11 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I/O
PIO3_0/DTR
36[3]
PIO3_1/DSR
37[3]
PIO3_2/DCD
43[3]
PIO3_3/RI
48[3]
no
no
no
no
Port 3 — Port 3 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 3 pins
depends on the function selected through the IOCONFIG
register block. Pins PIO3_6 to PIO3_11 are not available.
I/O
I; PU
PIO3_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
I/O
I; PU
PIO3_1 — General purpose digital input/output pin.
I
-
DSR — Data Set Ready input for UART.
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
I
-
DCD — Data Carrier Detect input for UART.
I/O
I; PU
PIO3_3 — General purpose digital input/output pin.
I
-
RI — Ring Indicator input for UART.
PIO3_4
18[3]
no
I/O
I; PU
PIO3_4 — General purpose digital input/output pin.
PIO3_5
21[3]
no
I/O
I; PU
PIO3_5 — General purpose digital input/output pin.
VDD
8; 44
-
I
-
3.3 V supply voltage to the internal regulator, the external rail,
and the ADC. Also used as the ADC reference voltage.
XTALIN
6[6]
-
I
-
Input to the oscillator circuit and internal clock generator circuits.
Input voltage must not exceed 1.8 V.
XTALOUT
7[6]
-
O
-
Output from the oscillator amplifier.
VSS
5; 41
-
I
-
Ground.
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to 2.6 V for
LPC111x/101/201/301, pins pulled up to full VDD level on LPC111x/102/202/302 (VDD = 3.3 V)); IA = inactive, no pull-up/down enabled.
[2]
See Figure 32 for the reset pad configuration. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to
reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down
mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 31).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled and the pin is not 5 V tolerant (see Figure 31).
[6]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
11 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC1111/12/13/14 pin description table (HVQFN33 package)
Symbol
Pin
Start Type
logic
input
Reset Description
state
[1]
PIO0_0 to PIO0_11
RESET/PIO0_0
PIO0_1/CLKOUT/
CT32B0_MAT2
Port 0 — Port 0 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 0 pins depends on
the function selected through the IOCONFIG register block.
2[2]
3[3]
yes
yes
I
I;PU
RESET — External reset input with 20 ns glitch filter. A LOW-going
pulse as short as 50 ns on this pin resets the device, causing I/O ports
and peripherals to take on their default states and processor execution
to begin at address 0.
I/O
-
PIO0_0 — General purpose digital input/output pin with 10 ns glitch
filter.
I/O
I;PU
PIO0_1 — General purpose digital input/output pin. A LOW level on
this pin during reset starts the ISP command handler.
O
-
CLKOUT — Clock out pin.
O
-
CT32B0_MAT2 — Match output 2 for 32-bit timer 0.
I/O
I;PU
PIO0_2 — General purpose digital input/output pin.
I/O
-
SSEL0 — Slave select for SPI0.
PIO0_2/SSEL0/
CT16B0_CAP0
8[3]
I
-
CT16B0_CAP0 — Capture input 0 for 16-bit timer 0.
PIO0_3
9[3]
yes
I/O
I;PU
PIO0_3 — General purpose digital input/output pin.
PIO0_4/SCL
10[4]
yes
I/O
I;PU
PIO0_4 — General purpose digital input/output pin (open-drain).
I/O
-
SCL — I2C-bus, open-drain clock input/output. High-current sink only
if I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I;PU
PIO0_5 — General purpose digital input/output pin (open-drain).
I/O
-
SDA — I2C-bus, open-drain data input/output. High-current sink only if
I2C Fast-mode Plus is selected in the I/O configuration register.
I/O
I;PU
PIO0_6 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
I;PU
PIO0_7 — General purpose digital input/output pin (high-current
output driver).
PIO0_5/SDA
PIO0_6/SCK0
11[4]
15[3]
yes
yes
yes
PIO0_7/CTS
16[3]
yes
I/O
I
-
CTS — Clear To Send input for UART.
PIO0_8/MISO0/
CT16B0_MAT0
17[3]
yes
I/O
I;PU
PIO0_8 — General purpose digital input/output pin.
I/O
-
MISO0 — Master In Slave Out for SPI0.
O
-
CT16B0_MAT0 — Match output 0 for 16-bit timer 0.
PIO0_9/MOSI0/
CT16B0_MAT1
18[3]
I/O
I;PU
PIO0_9 — General purpose digital input/output pin.
I/O
-
MOSI0 — Master Out Slave In for SPI0.
O
-
CT16B0_MAT1 — Match output 1 for 16-bit timer 0.
SWCLK/PIO0_10/
SCK0/
CT16B0_MAT2
19[3]
I
I;PU
SWCLK — Serial wire clock.
I/O
-
PIO0_10 — General purpose digital input/output pin.
I/O
-
SCK0 — Serial clock for SPI0.
O
-
CT16B0_MAT2 — Match output 2 for 16-bit timer 0.
LPC1111_12_13_14
Product data sheet
yes
yes
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
12 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC1111/12/13/14 pin description table (HVQFN33 package) …continued
Symbol
R/PIO0_11/AD0/
CT32B0_MAT3
Pin
21[5]
Start Type
logic
input
Reset Description
state
yes
-
I;PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO0_11 — General purpose digital input/output pin.
I
-
AD0 — A/D converter, input 0.
O
-
CT32B0_MAT3 — Match output 3 for 32-bit timer 0.
[1]
PIO1_0 to PIO1_11
R/PIO1_0/AD1/
CT32B1_CAP0
R/PIO1_1/AD2/
CT32B1_MAT0
R/PIO1_2/AD3/
CT32B1_MAT1
SWDIO/PIO1_3/
AD4/CT32B1_MAT2
PIO1_4/AD5/
CT32B1_MAT3/
WAKEUP
Port 1 — Port 1 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 1 pins depends on
the function selected through the IOCONFIG register block.
22[5]
23[5]
24[5]
25[5]
26[5]
PIO1_5/RTS/
CT32B0_CAP0
30[3]
PIO1_6/RXD/
CT32B0_MAT0
31[3]
LPC1111_12_13_14
Product data sheet
yes
no
no
no
no
no
no
-
I;PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_0 — General purpose digital input/output pin.
I
-
AD1 — A/D converter, input 1.
I
-
CT32B1_CAP0 — Capture input 0 for 32-bit timer 1.
-
I;PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_1 — General purpose digital input/output pin.
I
-
AD2 — A/D converter, input 2.
O
-
CT32B1_MAT0 — Match output 0 for 32-bit timer 1.
-
I;PU
R — Reserved. Configure for an alternate function in the IOCONFIG
block.
I/O
-
PIO1_2 — General purpose digital input/output pin.
I
-
AD3 — A/D converter, input 3.
O
-
CT32B1_MAT1 — Match output 1 for 32-bit timer 1.
I/O
I;PU
SWDIO — Serial wire debug input/output.
I/O
-
PIO1_3 — General purpose digital input/output pin.
I
-
AD4 — A/D converter, input 4.
O
-
CT32B1_MAT2 — Match output 2 for 32-bit timer 1.
I/O
I;PU
PIO1_4 — General purpose digital input/output pin with 10 ns glitch
filter.
I
-
AD5 — A/D converter, input 5.
O
-
CT32B1_MAT3 — Match output 3 for 32-bit timer 1.
I
-
WAKEUP — Deep power-down mode wake-up pin with 20 ns glitch
filter. This pin must be pulled HIGH externally to enter Deep
power-down mode and pulled LOW to exit Deep power-down mode. A
LOW-going pulse as short as 50 ns wakes up the part.
I/O
I;PU
PIO1_5 — General purpose digital input/output pin.
O
-
RTS — Request To Send output for UART.
I
-
CT32B0_CAP0 — Capture input 0 for 32-bit timer 0.
I/O
I;PU
PIO1_6 — General purpose digital input/output pin.
I
-
RXD — Receiver input for UART.
O
-
CT32B0_MAT0 — Match output 0 for 32-bit timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
13 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 4.
LPC1111/12/13/14 pin description table (HVQFN33 package) …continued
Symbol
PIO1_7/TXD/
CT32B0_MAT1
Pin
32[3]
PIO1_8/
CT16B1_CAP0
7[3]
PIO1_9/
CT16B1_MAT0
12[3]
PIO1_10/AD6/
CT16B1_MAT1
20[5]
PIO1_11/AD7
27[5]
Start Type
logic
input
Reset Description
state
no
I;PU
PIO1_7 — General purpose digital input/output pin.
no
no
no
no
I/O
[1]
O
-
TXD — Transmitter output for UART.
O
-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
I/O
I;PU
PIO1_8 — General purpose digital input/output pin.
I
-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
I/O
I;PU
PIO1_9 — General purpose digital input/output pin.
O
-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
I/O
I;PU
PIO1_10 — General purpose digital input/output pin.
I
-
AD6 — A/D converter, input 6.
O
-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
I/O
I;PU
PIO1_11 — General purpose digital input/output pin.
I
-
AD7 — A/D converter, input 7.
PIO2_0
PIO2_0/DTR
Port 2 — Port 2 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 2 pins depends on
the function selected through the IOCONFIG register block. Pins
PIO2_1 to PIO2_11 are not available.
1[3]
no
I/O
I;PU
PIO2_0 — General purpose digital input/output pin.
O
-
DTR — Data Terminal Ready output for UART.
PIO3_0 to PIO3_5
Port 3 — Port 3 is a 12-bit I/O port with individual direction and
function controls for each bit. The operation of port 3 pins depends on
the function selected through the IOCONFIG register block. Pins
PIO3_0, PIO3_1, PIO3_3 and PIO3_6 to PIO3_11 are not available.
PIO3_2
28[3]
no
I/O
I;PU
PIO3_2 — General purpose digital input/output pin.
PIO3_4
13[3]
no
I/O
I;PU
PIO3_4 — General purpose digital input/output pin.
PIO3_5
14[3]
no
I/O
I;PU
PIO3_5 — General purpose digital input/output pin.
VDD
6; 29 -
I
-
3.3 V supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
XTALIN
4[6]
-
I
-
Input to the oscillator circuit and internal clock generator circuits. Input
voltage must not exceed 1.8 V.
XTALOUT
5[6]
-
O
-
Output from the oscillator amplifier.
VSS
33
-
-
-
Thermal pad. Connect to ground.
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (pins pulled up to 2.6 V for
LPC111x/101/201/301, pins pulled up to full VDD level on LPC111x/102/202/302 (VDD = 3.3 V)); IA = inactive, no pull-up/down enabled.
[2]
See Figure 32 for the reset pad configuration. RESET functionality is not available in Deep power-down mode. Use the WAKEUP pin to
reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the Deep power-down
mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 31).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see Figure 31).
[6]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
14 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7. Functional description
7.1 ARM Cortex-M0 processor
The ARM Cortex-M0 is a general purpose, 32-bit microprocessor, which offers high
performance and very low power consumption.
7.2 On-chip flash program memory
The LPC1111/12/13/14 contain 32 kB (LPC1114), 24 kB (LPC1113), 16 kB (LPC1112), or
8 kB (LPC1111) of on-chip flash memory.
7.3 On-chip SRAM
The LPC1111/12/13/14 contain a total of 8 kB, 4 kB, or 2 kB on-chip static RAM memory.
7.4 Memory map
The LPC1111/12/13/14 incorporates several distinct memory regions, shown in the
following figures. Figure 4 shows the overall map of the entire address space from the
user program viewpoint following reset. The interrupt vector area supports address
remapping.
The AHB peripheral area is 2 megabyte in size, and is divided to allow for up to 128
peripherals. The APB peripheral area is 512 kB in size and is divided to allow for up to 32
peripherals. Each peripheral of either type is allocated 16 kilobytes of space. This allows
simplifying the address decoding for each peripheral.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
15 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
AHB peripherals
LPC1111/12/13/14
4 GB
0x5020 0000
0xFFFF FFFF
reserved
0xE010 0000
private peripheral bus
127-16 reserved
0xE000 0000
0x5004 0000
12-15
GPIO PIO3
0x5020 0000
8-11
GPIO PIO2
0x5000 0000
4-7
GPIO PIO1
0-3
GPIO PIO0
reserved
AHB peripherals
reserved
APB peripherals
0x5003 0000
0x5002 0000
0x5001 0000
0x5000 0000
0x4008 0000
31-23 reserved
0x4005 C000
0x4008 0000
APB peripherals
1 GB
SPI1(1)
22
0x4000 0000
0x4005 8000
21-19 reserved
0x4004 C000
reserved
0x2000 0000
0.5 GB
18
system control
17
IOCONFIG
16
15
SPI0
flash controller
14
PMU
reserved
0x4004 4000
0x4004 0000
0x4003 C000
0x4003 8000
13-10 reserved
0x1FFF 4000
16 kB boot ROM
0x4002 8000
9
reserved
8
reserved
0x4002 0000
0x1000 2000
7
ADC
0x4001 C000
0x1000 1000
6
32-bit counter/timer 1
0x4001 8000
0x1000 0800
5
32-bit counter/timer 0
0x4001 4000
4
16-bit counter/timer 1
0x4001 0000
3
16-bit counter/timer 0
0x4000 C000
2
UART
0x4000 8000
1
0
WDT
0x4000 4000
I2C-bus
0x4000 0000
0x1FFF 0000
reserved
8 kB SRAM (LPC1113/14/301/302)
4 kB SRAM (LPC1111/12/13/14/201/202)
2 kB SRAM (LPC1111/12/101/102)
0x1000 0000
reserved
0x0000 8000
32 kB on-chip flash (LPC1114)
24 kB on-chip flash (LPC1113)
16 kB on-chip flash (LPC1112)
8 kB on-chip flash (LPC1111)
0 GB
0x4004 8000
0x0000 6000
0x4002 4000
0x0000 4000
0x0000 2000
0x0000 00C0
active interrupt vectors
0x0000 0000
0x0000 0000
002aae699
(1) LQFP48 package only.
Fig 4.
LPC1111/12/13/14 memory map
7.5 Nested Vectored Interrupt Controller (NVIC)
The Nested Vectored Interrupt Controller (NVIC) is an integral part of the Cortex-M0. The
tight coupling to the CPU allows for low interrupt latency and efficient processing of late
arriving interrupts.
7.5.1 Features
• Controls system exceptions and peripheral interrupts.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
16 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• In the LPC1111/12/13/14, the NVIC supports 32 vectored interrupts including up to 13
inputs to the start logic from individual GPIO pins.
• Four programmable interrupt priority levels with hardware priority level masking.
• Software interrupt generation.
7.5.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 42 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
7.6 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC1111/12/13/14 use accelerated GPIO functions:
• GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
• Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of up to 42 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.7.1 Features
• Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
• Direction control of individual bits.
• All I/O default to inputs with pull-ups enabled after reset with the exception of the
I2C-bus pins PIO0_4 and PIO0_5.
• Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin (except for pins PIO0_4 and PIO0_5).
• On the LPC111x/101/201/301, all GPIO pins (except PIO0_4 and PIO0_5) are pulled
up to 2.6 V (VDD = 3.3 V) if their pull-up resistor is enabled in the IOCONFIG block.
• On the LPC111x/102/202/302, all GPIO pins (except PIO0_4 and PIO0_5) are pulled
up to 3.3 V (VDD = 3.3 V) if their pull-up resistor is enabled in the IOCONFIG block.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
17 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Programmable open-drain mode for parts LPC111x/102/202/302.
7.8 UART
The LPC1111/12/13/14 contain one UART.
Support for RS-485/9-bit mode allows both software address detection and automatic
address detection using 9-bit mode.
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.8.1 Features
•
•
•
•
•
Maximum UART data bit rate of 3.125 MBit/s.
16 Byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• FIFO control mechanism that enables software flow control implementation.
• Support for RS-485/9-bit mode.
• Support for modem control.
7.9 SPI serial I/O controller
The LPC1111/12/13/14 contain two SPI controllers on the LQFP48 package and one SPI
controller on the HVQFN33 packages (SPI0). Both SPI controllers support SSP features.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
7.9.1 Features
• Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
7.10 I2C-bus serial I/O controller
The LPC1111/12/13/14 contain one I2C-bus controller.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
18 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock Line
(SCL) and a Serial DAta line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C is a multi-master bus and can be
controlled by more than one bus master connected to it.
7.10.1 Features
• The I2C-interface is a standard I2C-bus compliant interface with open-drain pins. The
I2C-bus interface also supports Fast-mode Plus with bit rates up to 1 Mbit/s.
•
•
•
•
•
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
• The I2C-bus controller supports multiple address recognition and a bus monitor mode.
7.11 10-bit ADC
The LPC1111/12/13/14 contains one ADC. It is a single 10-bit successive approximation
ADC with eight channels.
7.11.1 Features
•
•
•
•
•
•
•
•
LPC1111_12_13_14
Product data sheet
10-bit successive approximation ADC.
Input multiplexing among 8 pins.
Power-down mode.
Measurement range 0 V to VDD.
10-bit conversion time  2.44 s (up to 400 kSamples/s).
Burst conversion mode for single or multiple inputs.
Optional conversion on transition of input pin or timer match signal.
Individual result registers for each ADC channel to reduce interrupt overhead.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
19 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.12 General purpose external event counter/timers
The LPC1111/12/13/14 includes two 32-bit counter/timers and two 16-bit counter/timers.
The counter/timer is designed to count cycles of the system derived clock. It can optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. Each counter/timer also includes one capture input to trap the timer value
when an input signal transitions, optionally generating an interrupt.
7.12.1 Features
• A 32-bit/16-bit timer/counter with a programmable 32-bit/16-bit prescaler.
• Counter or timer operation.
• One capture channel per timer, that can take a snapshot of the timer value when an
input signal transitions. A capture event may also generate an interrupt.
• Four match registers per timer that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
7.13 System tick timer
The ARM Cortex-M0 includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a fixed time interval (typically 10 ms).
7.14 Watchdog timer (LPC1100 series, LPC111x/101/201/301)
Remark: The watchdog timer without windowed features is available on parts
LPC111x/101/201/301 .
The purpose of the watchdog is to reset the microcontroller within a selectable time
period.
7.14.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
• Incorrect/Incomplete feed sequence causes reset/interrupt if enabled.
• Flag to indicate watchdog reset.
• Programmable 24-bit timer with internal prescaler.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
20 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  224  4) in
multiples of Tcy(WDCLK)  4.
• The Watchdog Clock (WDCLK) source can be selected from the Internal RC oscillator
(IRC), the Watchdog oscillator, or the main clock. This gives a wide range of potential
timing choices of Watchdog operation under different power reduction conditions. It
also provides the ability to run the WDT from an entirely internal source that is not
dependent on an external crystal and its associated components and wiring for
increased reliability.
7.15 Windowed WatchDog Timer (LPC1100L series, LPC111x/102/202/302)
Remark: The windowed watchdog timer is available on parts LPC111x/102/202/302 .
The purpose of the watchdog is to reset the controller if software fails to periodically
service it within a programmable time window.
7.15.1 Features
• Internally resets chip if not periodically reloaded during the programmable time-out
period.
• Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.
• Optional warning interrupt can be generated at a programmable time prior to
watchdog time-out.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect feed sequence causes reset or interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  224  4) in
multiples of Tcy(WDCLK)  4.
• The Watchdog Clock (WDCLK) source can be selected from the IRC or the dedicated
watchdog oscillator (WDO). This gives a wide range of potential timing choices of
watchdog operation under different power conditions.
7.16 Clocking and power control
7.16.1 Crystal oscillators
The LPC1111/12/13/14 include three independent oscillators. These are the system
oscillator, the Internal RC oscillator (IRC), and the Watchdog oscillator. Each oscillator can
be used for more than one purpose as required in a particular application.
Following reset, the LPC1111/12/13/14 will operate from the Internal RC oscillator until
switched by software. This allows systems to operate without any external crystal and the
bootloader code to operate at a known frequency.
See Figure 5 for an overview of the LPC1111/12/13/14 clock generation.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
21 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
SYSTEM CLOCK
DIVIDER
AHB clock 0
(system)
system clock
18
AHB clocks 1 to 18
(memories
and peripherals)
SYSAHBCLKCTRL[1:18]
(AHB clock enable)
IRC oscillator
SPI0 PERIPHERAL
CLOCK DIVIDER
SPI0
UART PERIPHERAL
CLOCK DIVIDER
UART
SPI1 PERIPHERAL
CLOCK DIVIDER
SPI1
WDT CLOCK
DIVIDER
WDT
main clock
watchdog oscillator
MAINCLKSEL
(main clock select)
IRC oscillator
SYSTEM PLL
system oscillator
IRC oscillator
SYSPLLCLKSEL
(system PLL clock select)
watchdog oscillator
WDTUEN
(WDT clock update enable)
IRC oscillator
system oscillator
watchdog oscillator
CLKOUTUEN
(CLKOUT update enable)
Fig 5.
CLKOUT PIN CLOCK
DIVIDER
CLKOUT pin
002aae514
LPC1111/12/13/14 clock generation block diagram
7.16.1.1
Internal RC oscillator
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
PLL and subsequently the CPU. The nominal IRC frequency is 12 MHz. The IRC is
trimmed to 1 % accuracy over the entire voltage and temperature range.
Upon power-up or any chip reset, the LPC1111/12/13/14 use the IRC as the clock source.
Software may later switch to one of the other available clock sources.
7.16.1.2
System oscillator
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
22 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.16.1.3
Watchdog oscillator
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 7.8 kHz and 1.7 MHz. The frequency spread over processing and
temperature is 40 %.
7.16.2 System PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
its frequency range while the PLL is providing the desired output frequency. The PLL
output frequency must be lower than 100 MHz. The output divider may be set to divide by
2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100 s.
7.16.3 Clock output
The LPC1111/12/13/14 features a clock output function that routes the IRC oscillator, the
system oscillator, the watchdog oscillator, or the main clock to an output pin.
7.16.4 Wake-up process
The LPC1111/12/13/14 begin operation at power-up and when awakened from Deep
power-down mode by using the 12 MHz IRC oscillator as the clock source. This allows
chip operation to resume quickly. If the system oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
7.16.5 Power control
The LPC1111/12/13/14 support a variety of power control features. There are three
special modes of processor power reduction: Sleep mode, Deep-sleep mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, a register is provided for shutting down the clocks to individual on-chip
peripherals, allowing fine tuning of power consumption by eliminating all dynamic power
use in any peripherals that are not required for the application. Selected peripherals have
their own clock divider which provides even better power control.
7.16.5.1
Power profiles (LPC1100L series, LPC111x/102/202/302 only)
The power consumption in Active and Sleep modes can be optimized for the application
through simple calls to the power profile. The power configuration routine configures the
LPC1111/12/13/14 for one of the following power modes:
• Default mode corresponding to power configuration after reset.
• CPU performance mode corresponding to optimized processing capability.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
23 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
• Efficiency mode corresponding to optimized balance of current consumption and CPU
performance.
• Low-current mode corresponding to lowest power consumption.
In addition, the power profile includes routines to select the optimal PLL settings for a
given system clock and PLL input clock.
7.16.5.2
Sleep mode
When Sleep mode is entered, the clock to the core is stopped. Resumption from the Sleep
mode does not need any special sequence but re-enabling the clock to the ARM core.
In Sleep mode, execution of instructions is suspended until either a reset or interrupt
occurs. Peripheral functions continue operation during Sleep mode and may generate
interrupts to cause the processor to resume execution. Sleep mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.16.5.3
Deep-sleep mode
In Deep-sleep mode, the chip is in Sleep mode, and in addition all analog blocks are shut
down. As an exception, the user has the option to keep the watchdog oscillator and the
BOD circuit running for self-timed wake-up and BOD protection. Deep-sleep mode allows
for additional power savings.
Up to 13 pins total serve as external wake-up pins to the start logic to wake up the chip
from Deep-sleep mode.
Unless the watchdog oscillator is selected to run in Deep-sleep mode, the clock source
should be switched to IRC before entering Deep-sleep mode, because the IRC can be
switched on and off glitch-free.
7.16.5.4
Deep power-down mode
In Deep power-down mode, power is shut off to the entire chip with the exception of the
WAKEUP pin. The LPC1111/12/13/14 can wake up from Deep power-down mode via the
WAKEUP pin.
A LOW-going pulse as short as 50 ns wakes up the part from Deep power-down mode.
When entering Deep power-down mode, an external pull-up resistor is required on the
WAKEUP pin to hold it HIGH. The RESET pin must also be held HIGH to prevent it from
floating while in Deep power-down mode.
7.17 System control
7.17.1 Start logic
The start logic connects external pins to corresponding interrupts in the NVIC. Each pin
shown in Table 3 to Table 4 as input to the start logic has an individual interrupt in the
NVIC interrupt vector table. The start logic pins can serve as external interrupt pins when
the chip is running. In addition, an input signal on the start logic pins can wake up the chip
from Deep-sleep mode when all clocks are shut down.
The start logic must be configured in the system configuration block and in the NVIC
before being used.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
24 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
7.17.2 Reset
Reset has four sources on the LPC1111/12/13/14: the RESET pin, the Watchdog reset,
Power-On Reset (POR), and the BrownOut Detection (BOD) circuit. The RESET pin is a
Schmitt trigger input pin. Assertion of chip reset by any source, once the operating voltage
attains a usable level, starts the IRC and initializes the flash controller.
A LOW-going pulse as short as 50 ns resets the part.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the boot block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
An external pull-up resistor is required on the RESET pin if Deep power-down mode is
used.
7.17.3 Brownout detection
The LPC1111/12/13/14 includes four levels for monitoring the voltage on the VDD pin. If
this voltage falls below one of the four selected levels, the BOD asserts an interrupt signal
to the NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the
NVIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading
a dedicated status register. Four additional threshold levels can be selected to cause a
forced reset of the chip.
7.17.4 Code security (Code Read Protection - CRP)
This feature of the LPC1111/12/13/14 allows user to enable different levels of security in
the system so that access to the on-chip flash and use of the Serial Wire Debugger (SWD)
and In-System Programming (ISP) can be restricted. When needed, CRP is invoked by
programming a specific pattern into a dedicated flash location. IAP commands are not
affected by the CRP.
In addition, ISP entry via the PIO0_1 pin can be disabled without enabling CRP. For
details see the LPC111x user manual.
There are three levels of Code Read Protection:
1. CRP1 disables access to the chip via the SWD and allows partial flash update
(excluding flash sector 0) using a limited set of the ISP commands. This mode is
useful when CRP is required and flash field updates are needed but all sectors can
not be erased.
2. CRP2 disables access to the chip via the SWD and only allows full flash erase and
update using a reduced set of the ISP commands.
3. Running an application with level CRP3 selected fully disables any access to the chip
via the SWD pins and the ISP. This mode effectively disables ISP override using
PIO0_1 pin, too. It is up to the user’s application to provide (if needed) flash update
mechanism using IAP calls or call reinvoke ISP command to enable flash update via
the UART.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
25 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
In addition to the three CRP levels, sampling of pin PIO0_1 for valid user code can be
disabled. For details see the LPC111x user manual.
7.17.5 APB interface
The APB peripherals are located on one APB bus.
7.17.6 AHBLite
The AHBLite connects the CPU bus of the ARM Cortex-M0 to the flash memory, the main
static RAM, and the Boot ROM.
7.17.7 External interrupt inputs
All GPIO pins can be level or edge sensitive interrupt inputs. In addition, start logic inputs
serve as external interrupts (see Section 7.17.1).
7.18 Emulation and debugging
Debug functions are integrated into the ARM Cortex-M0. Serial wire debug with four
breakpoints and two watchpoints is supported.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
26 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
8. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
VDD
supply voltage (core and external rail)
Min
Max
Unit
1.8
3.6
V
0.5
+5.5
V
VI
input voltage
5 V tolerant I/O
pins; only valid
when the VDD
supply voltage is
present
[2]
IDD
supply current
per supply pin
[3]
-
100
mA
[3]
-
100
mA
-
100
mA
65
+150
C
-
150
C
-
1.5
W
6500
+6500
V
ISS
ground current
per ground pin
Ilatch
I/O latch-up current
(0.5VDD) < VI <
(1.5VDD);
Tj < 125 C
Tstg
storage temperature
non-operating
Tj(max)
maximum junction temperature
Ptot(pack)
total power dissipation (per package)
based on package
heat transfer, not
device power
consumption
VESD
electrostatic discharge voltage
human body
model; all pins
[1]
[4]
[5]
The following applies to the limiting values:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Including voltage on outputs in 3-state mode.
[3]
The peak current is limited to 25 times the corresponding maximum current.
[4]
The maximum non-operating storage temperature is different than the temperature for required shelf life which should be determined
based on required shelf lifetime. Please refer to the JEDEC spec (J-STD-033B.1) for further details.
[5]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
27 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9. Static characteristics
Table 6.
Static characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
Parameter
VDD
supply voltage (core
and external rail)
Min
Typ[1]
Max
Unit
1.8
3.3
3.6
V
-
3
-
mA
-
9
-
mA
-
2
-
mA
[2][3][8]
-
6
-
A
[2][9]
-
220
-
nA
-
2
-
mA
-
7
-
mA
-
1
-
mA
[2][3][8]
-
2
-
A
[2][9]
-
220
-
nA
Conditions
LPC1100 series (LPC111x/101/201/301) power consumption
IDD
supply current
Active mode; code
while(1){}
executed from flash
system clock = 12 MHz
[2][3][4]
[5][6]
VDD = 3.3 V
system clock = 50 MHz
[2][3][5]
[6][7]
VDD = 3.3 V
Sleep mode;
[2][3][4]
[5][6]
system clock = 12 MHz
VDD = 3.3 V
Deep-sleep mode;
VDD = 3.3 V
Deep power-down mode;
VDD = 3.3 V
LPC1100L series (LPC111x/102/202/302) power consumption in low-current mode[10]
IDD
supply current
Active mode; code
while(1){}
executed from flash
system clock = 12 MHz
[2][3][4]
[5][6]
VDD = 3.3 V
system clock = 50 MHz
[2][3][5]
[6][7]
VDD = 3.3 V
Sleep mode;
[2][3][4]
[5][6]
system clock = 12 MHz
VDD = 3.3 V
Deep-sleep mode;
VDD = 3.3 V
Deep power-down mode;
VDD = 3.3 V
Standard port pins, RESET
IIL
LOW-level input current VI = 0 V; on-chip pull-up
resistor disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip
pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD;
on-chip pull-up/down
resistors disabled
-
0.5
10
nA
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
28 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 6.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
VI
Parameter
input voltage
Conditions
pin configured to provide
a digital function
[11][12]
Min
Typ[1]
Max
Unit
0
-
5.0
V
[13]
VO
output voltage
0
-
VDD
V
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
VOH
HIGH-level output
voltage
VOL
IOH
output active
-
0.4
-
V
2.0 V  VDD  3.6 V;
IOH = 4 mA
VDD  0.4
-
-
V
1.8 V  VDD < 2.0 V;
IOH = 3 mA
VDD  0.4
-
-
V
2.0 V  VDD  3.6 V;
IOL = 4 mA
-
-
0.4
V
1.8 V  VDD < 2.0 V;
IOL = 3 mA
-
-
0.4
V
HIGH-level output
current
VOH = VDD  0.4 V;
4
-
-
mA
3
-
-
mA
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
LOW-level output
voltage
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
IOL
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
3
-
-
mA
IOHS
HIGH-level short-circuit VOH = 0 V
output current
[14]
-
-
45
mA
IOLS
LOW-level short-circuit
output current
VOL = VDD
[14]
-
-
50
mA
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V;
15
50
85
A
10
50
85
A
0
0
0
A
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
VDD < VI < 5 V
High-drive output pin (PIO0_7)
IIL
LOW-level input current VI = 0 V; on-chip pull-up
resistor disabled
-
0.5
10
nA
IIH
HIGH-level input
current
VI = VDD; on-chip
pull-down resistor
disabled
-
0.5
10
nA
IOZ
OFF-state output
current
VO = 0 V; VO = VDD;
on-chip pull-up/down
resistors disabled
-
0.5
10
nA
VI
input voltage
pin configured to provide
a digital function
0
-
5.0
V
0
-
VDD
V
0.7VDD
-
-
V
VO
output voltage
VIH
HIGH-level input
voltage
LPC1111_12_13_14
Product data sheet
[11][12]
output active
[13]
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
29 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 6.
Static characteristics …continued
Tamb = 40 C to +85 C, unless otherwise specified.
Min
Typ[1]
Max
Unit
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
0.4
-
-
V
VOH
HIGH-level output
voltage
2.5 V VDD 3.6 V;
IOH = 20 mA
VDD  0.4
-
-
V
1.8 V VDD < 2.5 V;
IOH = 12 mA
VDD  0.4
-
-
V
2.0 V VDD 3.6 V;
IOL = 4 mA
-
-
0.4
V
1.8 V VDD < 2.0 V;
IOL = 3 mA
-
-
0.4
V
VOH = VDD  0.4 V;
2.5 V  VDD  3.6 V
20
-
-
mA
1.8 V  VDD < 2.5 V
12
-
-
mA
VOL = 0.4 V
4
-
-
mA
3
-
-
mA
-
-
50
mA
Symbol
Parameter
VIL
LOW-level output
voltage
VOL
HIGH-level output
current
IOH
LOW-level output
current
IOL
Conditions
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
[14]
IOLS
LOW-level short-circuit
output current
VOL = VDD
Ipd
pull-down current
VI = 5 V
10
50
150
A
Ipu
pull-up current
VI = 0 V
15
50
85
A
10
50
85
A
0
0
0
A
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
VDD < VI < 5 V
I2C-bus
pins (PIO0_4 and PIO0_5)
VIH
HIGH-level input
voltage
0.7VDD
-
-
V
VIL
LOW-level input voltage
-
-
0.3VDD
V
Vhys
hysteresis voltage
-
0.05VDD
-
V
3.5
-
-
mA
3
-
-
20
-
-
16
-
-
IOL
LOW-level output
current
I2C-bus
VOL = 0.4 V;
pins
configured as standard
mode pins
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
IOL
LOW-level output
current
I2C-bus
VOL = 0.4 V;
pins
configured as Fast-mode
Plus pins
mA
2.0 V  VDD  3.6 V
1.8 V  VDD < 2.0 V
ILI
input leakage current
VI = VDD
VI = 5 V
[15]
-
2
4
A
-
10
22
A
Oscillator pins
Vi(xtal)
crystal input voltage
0.5
1.8
1.95
V
Vo(xtal)
crystal output voltage
0.5
1.8
1.95
V
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
30 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
[2]
Tamb = 25 C.
[3]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[4]
IRC enabled; system oscillator disabled; system PLL disabled.
[5]
BOD disabled.
[6]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART and SPI0/1 disabled in system configuration
block.
[7]
IRC disabled; system oscillator enabled; system PLL enabled.
[8]
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 18FF.
[9]
WAKEUP pin pulled HIGH externally.
[10] Low-current mode PWR_LOW_CURRENT selected when running the set_power routine in the power profiles.
[11] Including voltage on outputs in 3-state mode.
[12] VDD supply voltage must be present.
[13] 3-state outputs go into 3-state mode in Deep power-down mode.
[14] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[15] To VSS.
Table 7.
ADC static characteristics
Tamb = 40 C to +85 C unless otherwise specified; ADC frequency 4.5 MHz, VDD = 2.5 V to 3.6 V.
Symbol
Parameter
VIA
analog input voltage
0
-
VDD
V
Cia
analog input capacitance
-
-
1
pF
ED
differential linearity error
[1][2]
-
-
1
LSB
integral non-linearity
[3]
-
-
 1.5
LSB
EO
offset error
[4]
-
-
 3.5
LSB
EG
gain error
[5]
-
-
0.6
%
ET
absolute error
[6]
-
-
4
LSB
Rvsi
voltage source interface
resistance
-
-
40
k
Ri
input resistance
-
-
2.5
M
EL(adj)
Conditions
Min
[7][8]
Typ
Max
Unit
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 6.
[3]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 6.
[4]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 6.
[5]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 6.
[6]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve. See Figure 6.
[7]
Tamb = 25 C; maximum sampling frequency fs = 400 kSamples/s and analog input capacitance Cia = 1 pF.
[8]
Input resistance Ri depends on the sampling frequency fs: Ri = 1 / (fs  Cia).
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
31 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
offset error
EO
1 LSB =
VDD − VSS
1024
002aaf426
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 6.
ADC characteristics
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
32 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.1 BOD static characteristics
Table 8.
BOD static characteristics[1]
Tamb = 25 C.
Symbol
Parameter
Conditions
Vth
threshold voltage
interrupt level 0
Min
Typ
Max
Unit
assertion
-
1.65
-
V
de-assertion
-
1.80
-
V
assertion
-
2.22
-
V
de-assertion
-
2.35
-
V
assertion
-
2.52
-
V
de-assertion
-
2.66
-
V
assertion
-
2.80
-
V
de-assertion
-
2.90
-
V
interrupt level 1
interrupt level 2
interrupt level 3
reset level 0
assertion
-
1.46
-
V
de-assertion
-
1.63
-
V
assertion
-
2.06
-
V
de-assertion
-
2.15
-
V
assertion
-
2.35
-
V
de-assertion
-
2.43
-
V
assertion
-
2.63
-
V
de-assertion
-
2.71
-
V
reset level 1
reset level 2
reset level 3
[1]
Interrupt levels are selected by writing the level value to the BOD control register BODCTRL, see LPC111x
user manual.
9.2 Power consumption LPC111x/101/201/301
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see LPC111x user manual):
• Configure all pins as GPIO with pull-up resistor disabled in the IOCONFIG block.
• Configure GPIO pins as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
33 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf390
12
IDD
(mA)
48 MHz(2)
8
36 MHz(2)
24 MHz(2)
4
12 MHz(1)
0
1.8
2.4
3.0
3.6
VDD (V)
Conditions: Tamb = 25 C; active mode entered executing code while(1){} from flash; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; internal pull-up resistors disabled; BOD disabled.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 7.
Active mode: Typical supply current IDD versus supply voltage VDD for different
system clock frequencies (for LPC111x/101/201/301)
002aaf391
12
IDD
(mA)
48 MHz(2)
8
36 MHz(2)
24 MHz(2)
4
0
−40
12 MHz(1)
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; active mode entered executing code while(1){} from flash; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; internal pull-up resistors disabled; BOD disabled.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 8.
LPC1111_12_13_14
Product data sheet
Active mode: Typical supply current IDD versus temperature for different system
clock frequencies (for LPC111x/101/201/301)
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
34 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf392
8
IDD
(mA)
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; sleep mode entered from flash; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks disabled; internal
pull-up resistors disabled; BOD disabled.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 9.
Sleep mode: Typical supply current IDD versus temperature for different system
clock frequencies (for LPC111x/101/201/301)
002aaf394
40
IDD
(μA)
30
3.6 V
3.3 V
2.0 V
1.8 V
20
10
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks disabled in the PDSLEEPCFG register
(PDSLEEPCFG = 0x0000 18FF).
Fig 10. Deep-sleep mode: Typical supply current IDD versus temperature for different
supply voltages VDD (for LPC111x/101/201/301)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
35 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf457
0.8
IDD
(μA)
0.6
VDD = 3.6 V
3.3 V
2.0 V
1.8 V
0.4
0.2
0
−40
−15
10
35
60
85
temperature (°C)
Fig 11. Deep power-down mode: Typical supply current IDD versus temperature for
different supply voltages VDD (for LPC111x/101/201/301)
9.3 Power consumption LPC111x/102/202/302
Power measurements in Active, Sleep, and Deep-sleep modes were performed under the
following conditions (see LPC111x user manual):
• Configure all pins as GPIO with pull-up resistor disabled in the IOCONFIG block.
• Configure GPIO pins as outputs using the GPIOnDIR registers.
• Write 0 to all GPIOnDATA registers to drive the outputs LOW.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
36 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf980
10
IDD
(mA)
8
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
1.8
2.4
3.0
3.6
VDD (V)
Conditions: Tamb = 25 C; active mode entered executing code while(1){} from flash; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 12. Active mode: Typical supply current IDD versus supply voltage VDD for different
system clock frequencies (for LPC111x/102/202/302)
002aaf981
10
IDD
(mA)
8
48 MHz(2)
6
36 MHz(2)
4
24 MHz(2)
12 MHz(1)
2
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; active mode entered executing code while(1){} from flash; all peripherals
disabled in the SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks
disabled; internal pull-up resistors disabled; BOD disabled; low-current mode.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 13. Active mode: Typical supply current IDD versus temperature for different system
clock frequencies (for LPC111x/102/202/302)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
37 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf982
6
IDD
(mA)
48 MHz(2)
4
36 MHz(2)
24 MHz(2)
2
12 MHz(1)
0
−40
−15
10
35
60
85
temperature (°C)
Conditions: VDD = 3.3 V; sleep mode entered from flash; all peripherals disabled in the
SYSAHBCLKCTRL register (SYSAHBCLKCTRL = 0x1F); all peripheral clocks disabled; internal
pull-up resistors disabled; BOD disabled; low-current mode.
(1) System oscillator and system PLL disabled; IRC enabled.
(2) System oscillator and system PLL enabled; IRC disabled.
Fig 14. Sleep mode: Typical supply current IDD versus temperature for different system
clock frequencies (for LPC111x/102/202/302)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
38 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aaf977
5.5
IDD
(μA)
4.5
3.5
VDD = 3.3 V, 3.6 V
1.8 V
2.5
1.5
−40
−15
10
35
60
85
temperature (°C)
Conditions: BOD disabled; all oscillators and analog blocks disabled in the PDSLEEPCFG register
(PDSLEEPCFG = 0x0000 18FF).
Fig 15. Deep-sleep mode: Typical supply current IDD versus temperature for different
supply voltages VDD (for LPC111x/102/202/302)
002aaf978
0.8
IDD
(μA)
VDD = 3.6 V
3.3 V
1.8 V
0.6
0.4
0.2
0
−40
−15
10
35
60
85
temperature (°C)
Fig 16. Deep power-down mode: Typical supply current IDD versus temperature for
different supply voltages VDD (for LPC111x/102/202/302)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
39 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.4 Peripheral power consumption
The supply current per peripheral is measured as the difference in supply current between
the peripheral block enabled and the peripheral block disabled in the SYSAHBCLKCFG
and PDRUNCFG (for analog blocks) registers. All other blocks are disabled in both
registers and no code is executed. Measured on a typical sample at Tamb = 25 C. Unless
noted otherwise, the system oscillator and PLL are running in both measurements.
The supply currents are shown for system clock frequencies of 12 MHz and 48 MHz.
Table 9.
Power consumption for individual analog and digital blocks
Peripheral
LPC1111_12_13_14
Product data sheet
Typical supply current in
mA
Notes
n/a
12 MHz
48 MHz
IRC
0.27
-
-
System oscillator running; PLL off; independent
of main clock frequency.
System oscillator
at 12 MHz
0.22
-
-
IRC running; PLL off; independent of main clock
frequency.
Watchdog
oscillator at
500 kHz/2
0.004
-
-
System oscillator running; PLL off; independent
of main clock frequency.
BOD
0.051
-
-
Independent of main clock frequency.
Main PLL
-
0.21
-
ADC
-
0.08
0.29
CLKOUT
-
0.12
0.47
CT16B0
-
0.02
0.06
CT16B1
-
0.02
0.06
CT32B0
-
0.02
0.07
CT32B1
-
0.02
0.06
GPIO
-
0.23
0.88
IOCONFIG
-
0.03
0.10
I2C
-
0.04
0.13
ROM
-
0.04
0.15
SPI0
-
0.12
0.45
SPI1
-
0.12
0.45
UART
-
0.22
0.82
WDT
-
0.02
0.06
Main clock divided by 4 in the CLKOUTDIV
register.
GPIO pins configured as outputs and set to
LOW. Direction and pin state are maintained if
the GPIO is disabled in the SYSAHBCLKCFG
register.
Main clock selected as clock source for the
WDT.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
40 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
9.5 Electrical pin characteristics
002aae990
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
10
20
30
40
50
60
IOH (mA)
Conditions: VDD = 3.3 V; on pin PIO0_7.
Fig 17. High-drive output: Typical HIGH-level output voltage VOH versus HIGH-level
output current IOH.
002aaf019
60
T = 85 °C
25 °C
−40 °C
IOL
(mA)
40
20
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; on pins PIO0_4 and PIO0_5.
Fig 18. I2C-bus pins (high current sink): Typical LOW-level output current IOL versus
LOW-level output voltage VOL
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
41 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae991
15
IOL
(mA)
T = 85 °C
25 °C
−40 °C
10
5
0
0
0.2
0.4
0.6
VOL (V)
Conditions: VDD = 3.3 V; standard port pins and PIO0_7.
Fig 19. Typical LOW-level output current IOL versus LOW-level output voltage VOL
002aae992
3.6
VOH
(V)
T = 85 °C
25 °C
−40 °C
3.2
2.8
2.4
2
0
8
16
24
IOH (mA)
Conditions: VDD = 3.3 V; standard port pins.
Fig 20. Typical HIGH-level output voltage VOH versus HIGH-level output source current
IOH
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
42 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
002aae988
10
Ipu
(μA)
−10
−30
T = 85 °C
25 °C
−40 °C
−50
−70
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 21. Typical pull-up current Ipu versus input voltage VI
002aae989
80
T = 85 °C
25 °C
−40 °C
Ipd
(μA)
60
40
20
0
0
1
2
3
4
5
VI (V)
Conditions: VDD = 3.3 V; standard port pins.
Fig 22. Typical pull-down current Ipd versus input voltage VI
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
43 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10. Dynamic characteristics
10.1 Power-up ramp conditions
Table 10. Power-up characteristics
Tamb = 40 C to +85 C.
Symbol Parameter
tr
rise time
twait
wait time
VI
input voltage
Conditions
Min
at t = t1: 0 < VI 400 mV
[1]
[1][2]
at t = t1 on pin VDD
Typ
Max
Unit
0
-
500
ms
12
-
-
s
0
-
400
mV
[1]
See Figure 23.
[2]
The wait time specifies the time the power supply must be at levels below 400 mV before ramping up.
tr
VDD
400 mV
0
twait
t = t1
002aag001
Condition: 0 < VI 400 mV at start of power-up (t = t1)
Fig 23. Power-up ramp
10.2 Flash memory
Table 11. Flash characteristics
Tamb = 40 C to +85 C, unless otherwise specified.
Symbol
LPC1111_12_13_14
Product data sheet
Parameter
Conditions
Min
[1]
Nendu
endurance
tret
retention time
ter
erase time
tprog
programming
time
Typ
Max
Unit
10000
100000
-
cycles
powered
10
-
-
years
unpowered
20
-
-
years
sector or multiple
consecutive
sectors
95
100
105
ms
0.95
1
1.05
ms
[2]
[1]
Number of program/erase cycles.
[2]
Programming times are given for writing 256 bytes from RAM to the flash. Data must be written to the flash
in blocks of 256 bytes.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
44 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.3 External clock
Table 12. Dynamic characteristic: external clock
Tamb = 40 C to +85 C; VDD over specified ranges.[1]
Min
Typ[2]
Max
Unit
oscillator frequency
1
-
25
MHz
Symbol
Parameter
fosc
Conditions
Tcy(clk)
clock cycle time
40
-
1000
ns
tCHCX
clock HIGH time
Tcy(clk)  0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk)  0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
tCHCL
tCHCX
tCLCH
tCLCX
Tcy(clk)
002aaa907
Fig 24. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
45 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.4 Internal oscillators
Table 13. Dynamic characteristic: internal oscillators
Tamb = 40 C to +85 C; 2.7 V  VDD  3.6 V.[1]
Symbol
Parameter
Conditions
fosc(RC)
internal RC oscillator frequency -
Min
Typ[2]
Max
Unit
11.88
12
12.12
MHz
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
002aaf403
12.15
f
(MHz)
VDD = 3.6 V
3.3 V
3.0 V
2.7 V
2.4 V
2.0 V
12.05
11.95
11.85
−40
−15
10
35
60
85
temperature (°C)
Conditions: Frequency values are typical values. 12 MHz  1 % accuracy is guaranteed for
2.7 V  VDD  3.6 V and Tamb = 40 C to +85 C. Variations between parts may cause the IRC to
fall outside the 12 MHz  1 % accuracy specification for voltages below 2.7 V.
Fig 25. Internal RC oscillator frequency versus temperature
Table 14.
Dynamic characteristics: Watchdog oscillator
Min
Typ[1]
Max
Unit
internal oscillator DIVSEL = 0x1F, FREQSEL = 0x1
frequency
in the WDTOSCCTRL register;
[2][3]
-
7.8
-
kHz
DIVSEL = 0x00, FREQSEL = 0xF
in the WDTOSCCTRL register
[2][3]
-
1700
-
kHz
Symbol Parameter
fosc(int)
LPC1111_12_13_14
Product data sheet
Conditions
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[2]
The typical frequency spread over processing and temperature (Tamb = 40 C to +85 C) is 40 %.
[3]
See the LPC111x user manual.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
46 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
10.5 I/O pins
Table 15. Dynamic characteristic: I/O pins[1]
Tamb = 40 C to +85 C; 3.0 V  VDD  3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
pin
configured as
output
3.0
-
5.0
ns
tf
fall time
pin
configured as
output
2.5
-
5.0
ns
[1]
Applies to standard port pins and RESET pin.
10.6 I2C-bus
Table 16. Dynamic characteristic: I2C-bus pins[1]
Tamb = 40 C to +85 C.[2]
Symbol
Parameter
Conditions
Min
Max
Unit
fSCL
SCL clock
frequency
Standard-mode
0
100
kHz
Fast-mode
0
400
kHz
Fast-mode Plus
0
1
MHz
of both SDA and
SCL signals
-
300
ns
20 + 0.1  Cb
300
ns
[4][5][6][7]
fall time
tf
Standard-mode
Fast-mode
Fast-mode Plus
tLOW
tHIGH
tHD;DAT
tSU;DAT
[1]
LPC1111_12_13_14
Product data sheet
LOW period of
the SCL clock
HIGH period of
the SCL clock
data hold time
data set-up
time
[3][4][8]
[9][10]
-
120
ns
Standard-mode
4.7
-
s
Fast-mode
1.3
-
s
Fast-mode Plus
0.5
-
s
Standard-mode
4.0
-
s
Fast-mode
0.6
-
s
Fast-mode Plus
0.26
-
s
Standard-mode
0
-
s
Fast-mode
0
-
s
Fast-mode Plus
0
-
s
Standard-mode
250
-
ns
Fast-mode
100
-
ns
Fast-mode Plus
50
-
ns
See the I2C-bus specification UM10204 for details.
[2]
Parameters are valid over operating temperature range unless otherwise specified.
[3]
tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission
and the acknowledge.
[4]
A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the
VIH(min) of the SCL signal) to bridge the undefined region of the falling edge of SCL.
[5]
Cb = total capacitance of one bus line in pF.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
47 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
[6]
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA
output stage tf is specified at 250 ns. This allows series protection resistors to be connected in between the
SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf.
[7]
In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors
are used, designers should allow for this when considering bus timing.
[8]
The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than
the maximum of tVD;DAT or tVD;ACK by a transition time (see UM10204). This maximum must only be met if
the device does not stretch the LOW period (tLOW) of the SCL signal. If the clock stretches the SCL, the
data must be valid by the set-up time before it releases the clock.
[9]
tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in
transmission and the acknowledge.
[10] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement
tSU;DAT = 250 ns must then be met. This will automatically be the case if the device does not stretch the
LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must
output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the
Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must
meet this set-up time.
tf
SDA
tSU;DAT
70 %
30 %
70 %
30 %
tHD;DAT
tf
70 %
30 %
SCL
tVD;DAT
tHIGH
70 %
30 %
70 %
30 %
70 %
30 %
tLOW
S
1 / fSCL
002aaf425
Fig 26. I2C-bus pins clock timing
10.7 SPI interfaces
Table 17.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
-
-
ns
SPI master (in SPI mode)
Tcy(clk)
tDS
clock cycle time
data set-up time
full-duplex mode
[1]
50
when only transmitting
[1]
40
in SPI mode
[2]
15
2.0 V  VDD < 2.4 V
[2]
20
1.8 V  VDD < 2.0 V
[2]
24
-
-
ns
ns
-
-
ns
2.4 V  VDD  3.6 V
ns
tDH
data hold time
in SPI mode
[2]
0
-
-
ns
tv(Q)
data output valid time in SPI mode
[2]
-
-
10
ns
data output hold time in SPI mode
[2]
0
-
-
ns
th(Q)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
48 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Table 17.
Dynamic characteristics of SPI pins in SPI mode
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
SPI slave (in SPI mode)
Tcy(PCLK)
PCLK cycle time
data set-up time
tDS
20
-
-
ns
in SPI mode
[3][4]
0
-
-
ns
tDH
data hold time
in SPI mode
[3][4]
3  Tcy(PCLK) + 4
-
-
ns
tv(Q)
data output valid time in SPI mode
[3][4]
-
-
3  Tcy(PCLK) + 11
ns
th(Q)
data output hold time in SPI mode
[3][4]
-
-
2  Tcy(PCLK) + 5
ns
[1]
Tcy(clk) = (SSPCLKDIV  (1 + SCR)  CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SPI peripheral clock divider (SSPCLKDIV), the SPI SCR parameter (specified in the SSP0CR0 register),
and the SPI CPSDVSR parameter (specified in the SPI clock prescale register).
[2]
Tamb = 40 C to 85 C.
[3]
Tcy(clk) = 12  Tcy(PCLK).
[4]
Tamb = 25 C; for normal voltage supply range: VDD = 3.3 V.
Tcy(clk)
tclk(H)
tclk(L)
SCK (CPOL = 0)
SCK (CPOL = 1)
tv(Q)
th(Q)
DATA VALID
MOSI
DATA VALID
tDS
DATA VALID
MISO
tDH
DATA VALID
tv(Q)
MOSI
DATA VALID
th(Q)
DATA VALID
tDH
tDS
MISO
DATA VALID
CPHA = 1
CPHA = 0
DATA VALID
002aae829
Pin names SCK, MISO, and MOSI refer to pins for both SPI peripherals, SPI0 and SPI1.
Fig 27. SPI master timing in SPI mode
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
49 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Tcy(clk)
tclk(H)
tclk(L)
tDS
tDH
SCK (CPOL = 0)
SCK (CPOL = 1)
MOSI
DATA VALID
DATA VALID
tv(Q)
MISO
th(Q)
DATA VALID
tDS
MOSI
DATA VALID
tDH
DATA VALID
tv(Q)
MISO
DATA VALID
CPHA = 1
DATA VALID
th(Q)
CPHA = 0
DATA VALID
002aae830
Pin names SCK, MISO, and MOSI refer to pins for both SPI peripherals, SPI0 and SPI1.
Fig 28. SPI slave timing in SPI mode
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
50 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11. Application information
11.1 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
environment beyond the ADC specifications listed in Table 7:
• The ADC input trace must be short and as close as possible to the LPC1111/12/13/14
chip.
• The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
• Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
• To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
Ci = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground Cg which attenuates the input voltage by a factor Ci/(Ci + Cg). In slave
mode, a minimum of 200 mV (RMS) is needed.
LPC1xxx
XTALIN
Ci
100 pF
Cg
002aae788
Fig 29. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure 29), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in Figure 30 and in
Table 18 and Table 19. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances CX1 and CX2 need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, CL and
RS). Capacitance CP in Figure 30 represents the parallel package capacitance and should
not be larger than 7 pF. Parameters FOSC, CL, RS and CP are supplied by the crystal
manufacturer (see Table 18).
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
51 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
LPC1xxx
L
XTALIN
XTALOUT
=
CL
CP
XTAL
RS
CX2
CX1
002aaf424
Fig 30. Oscillator modes and models: oscillation mode of operation and external crystal
model used for CX1/CX2 evaluation
Table 18.
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) low frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
1 MHz - 5 MHz
10 pF
< 300 
18 pF, 18 pF
20 pF
< 300 
39 pF, 39 pF
5 MHz - 10 MHz
10 MHz - 15 MHz
15 MHz - 20 MHz
Table 19.
30 pF
< 300 
57 pF, 57 pF
10 pF
< 300 
18 pF, 18 pF
20 pF
< 200 
39 pF, 39 pF
30 pF
< 100 
57 pF, 57 pF
10 pF
< 160 
18 pF, 18 pF
20 pF
< 60 
39 pF, 39 pF
10 pF
< 80 
18 pF, 18 pF
Recommended values for CX1/CX2 in oscillation mode (crystal and external
components parameters) high frequency mode
Fundamental oscillation
frequency FOSC
Crystal load
capacitance CL
Maximum crystal
series resistance RS
External load
capacitors CX1, CX2
15 MHz - 20 MHz
10 pF
< 180 
18 pF, 18 pF
20 pF
< 100 
39 pF, 39 pF
20 MHz - 25 MHz
10 pF
< 160 
18 pF, 18 pF
20 pF
< 80 
39 pF, 39 pF
11.3 XTAL Printed Circuit Board (PCB) layout guidelines
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors Cx1, Cx2, and Cx3 in case of
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plain. Loops must be made as small as possible in
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
52 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
order to keep the noise coupled in via the PCB as small as possible. Also parasitics
should stay as small as possible. Values of Cx1 and Cx2 should be chosen smaller
accordingly to the increase in parasitics of the PCB layout.
11.4 Standard I/O pad configuration
Figure 31 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
Digital output driver
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
VDD
ESD
output enable
pin configured
as digital output
driver
output
PIN
ESD
VDD
VSS
weak
pull-up
pull-up enable
pin configured
as digital input
weak
pull-down
repeater mode
enable
pull-down enable
data input
select analog input
pin configured
as analog input
analog input
002aaf304
Fig 31. Standard I/O pad configuration
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
53 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
11.5 Reset pad configuration
VDD
VDD
VDD
Rpu
ESD
20 ns RC
GLITCH FILTER
reset
PIN
ESD
VSS
002aaf274
Fig 32. Reset pad configuration
11.6 ElectroMagnetic Compatibility (EMC)
Radiated emission measurements according to the IEC61967-2 standard using the
TEM-cell method are shown for the LPC1114FBD48/302 in Table 20.
Table 20.
ElectroMagnetic Compatibility (EMC) for part LPC1114FBD48/302 (TEM-cell
method)
VDD = 3.3 V; Tamb = 25 C.
Parameter
Frequency band
System clock =
Unit
12 MHz
24 MHz
48 MHz
150 kHz - 30 MHz
7
5
7
dBV
30 MHz - 150 MHz
2
1
10
dBV
Input clock: IRC (12 MHz)
maximum
peak level
IEC level[1]
150 MHz - 1 GHz
4
8
16
dBV
-
O
N
M
-
Input clock: crystal oscillator (12 MHz)
maximum
peak level
LPC1111_12_13_14
Product data sheet
150 kHz - 30 MHz
7
7
7
dBV
30 MHz - 150 MHz
2
1
8
dBV
150 MHz - 1 GHz
4
7
14
dBV
-
O
N
M
-
IEC
level[1]
[1]
IEC levels refer to Appendix D in the IEC61967-2 Specification.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
54 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
12. Package outline
LQFP48: plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
c
y
X
36
25
A
37
24
ZE
e
E HE
A A2
(A 3)
A1
w M
θ
bp
pin 1 index
Lp
L
13
48
detail X
12
1
ZD
e
v M A
w M
bp
D
B
HD
v M B
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HD
HE
L
Lp
v
w
y
mm
1.6
0.20
0.05
1.45
1.35
0.25
0.27
0.17
0.18
0.12
7.1
6.9
7.1
6.9
0.5
9.15
8.85
9.15
8.85
1
0.75
0.45
0.2
0.12
0.1
Z D (1) Z E (1)
θ
0.95
0.55
7o
o
0
0.95
0.55
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT313-2
136E05
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-25
Fig 33. Package outline SOT313-2 (LQFP48)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
55 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
HVQFN33: plastic thermal enhanced very thin quad flat package; no leads;
33 terminals; body 7 x 7 x 0.85 mm
A
B
D
terminal 1
index area
E
A
A1
c
detail X
e1
e
9
16
C
C A B
C
v
w
b
y
y1 C
L
8
17
e
e2
Eh
33
1
terminal 1
index area
24
32
X
25
Dh
0
2.5
scale
Dimensions
Unit
mm
5 mm
A(1)
A1
b
max 1.00 0.05 0.35
nom 0.85 0.02 0.28
min 0.80 0.00 0.23
c
D(1)
Dh
E(1)
0.2
7.1
7.0
6.9
4.85
4.70
4.55
7.1
7.0
6.9
Eh
e
e1
e2
L
0.75
4.85
4.70 0.65 4.55 4.55 0.60
0.45
4.55
v
0.1
w
y
0.05 0.08
y1
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
Outline
version
References
IEC
JEDEC
JEITA
---
hvqfn33_po
European
projection
Issue date
09-03-17
09-03-23
Fig 34. Package outline (HVQFN33)
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
56 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
13. Soldering
Footprint information for reflow soldering of LQFP48 package
SOT313-2
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
P2
0.500
0.560
Ax
Ay
10.350 10.350
Bx
By
C
D1
D2
Gx
7.350
7.350
1.500
0.280
0.500
7.500
Gy
Hx
Hy
7.500 10.650 10.650
sot313-2_fr
Fig 35. Reflow soldering of the LQFP48 package
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
57 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Footprint information for reflow soldering of HVQFN33 package
OID = 8.20 OA
PID = 7.25 PA+OA
OwDtot = 5.10 OA
evia = 4.25
0.20 SR
chamfer (4×)
W = 0.30 CU
SPD = 1.00 SP
LaE = 7.95 CU
PIE = 7.25 PA+OA
LbE = 5.80 CU
evia = 4.25
evia = 1.05
0.45 DM
SPE = 1.00 SP
GapE = 0.70 SP
4.55 SR
SEhtot = 2.70 SP
EHS = 4.85 CU
OwEtot = 5.10 OA
OIE = 8.20 OA
e = 0.65
0.45 DM
GapD = 0.70 SP
evia = 2.40
B-side
SDhtot = 2.70 SP
4.55 SR
DHS = 4.85 CU
Solder resist
covered via
0.30 PH
LbD = 5.80 CU
0.60 SR cover
LaD = 7.95 CU
0.60 CU
(A-side fully covered)
number of vias: 20
solder land
solder land plus solder paste
solder paste deposit
solder resist
occupied area
Dimensions in mm
Remark:
Stencil thickness: 0.125 mm
001aao134
Fig 36. Reflow soldering of the HVQFN33 package
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
58 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
14. Abbreviations
Table 21.
LPC1111_12_13_14
Product data sheet
Abbreviations
Acronym
Description
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
APB
Advanced Peripheral Bus
BOD
BrownOut Detection
GPIO
General Purpose Input/Output
PLL
Phase-Locked Loop
RC
Resistor-Capacitor
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SSP
Synchronous Serial Port
TEM
Transverse ElectroMagnetic
UART
Universal Asynchronous Receiver/Transmitter
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
59 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
15. Revision history
Table 22.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
LPC1111_12_13_14 v.5
20110622
Product data sheet
-
LPC1111_12_13_14 v.4
Modifications:
•
•
•
•
•
•
•
•
•
LPC1111_12_13_14 v.4
Modifications:
LPC1111_12_13_14 v.3
Modifications:
LPC1111_12_13_14 v.2
Modifications:
LPC1111_12_13_14 v.1
LPC1111_12_13_14
Product data sheet
ADC sampling frequency corrected in Table 7 (Table note 7).
Pull-up level specified in Table 3 to Table 4 and Section 7.7.1.
Parameter Tcy(clk) corrected on Table 17.
WWDT for parts LPC111x/102/202/302 added in Section 2 and Section 7.15.
Programmable open-drain mode for parts LPC111x/102/202/302 added in Section 2
and Section 7.12.
Condition for parameter Tstg in Table 5 updated.
Table note 4 of Table 5 updated.
Section 13 added.
Removed PLCC44 package information.
20110210
Product data sheet
-
LPC1111_12_13_14 v.3
•
Power consumption graphs added for parts LPC111x/102/202/302 (Figure 13 to
Figure 17).
•
•
•
Parameter Vhys for I2C bus pins: typical value corrected Vhys = 0.05VDD in Table 7.
•
•
Section 11.6 “ElectroMagnetic Compatibility (EMC)” added.
Typical value for parameter Nendu added in Table 12 “Flash characteristics”.
I2C-bus pins configured as standard mode pins, parameter IOL changed to 3.5 mA
(minimum) for 2.0 V  VDD  3.6 V.
Power-up characterization added (Section 10.1 “Power-up ramp conditions”).
20101110
•
•
•
•
•
•
Product data sheet
-
LPC1111_12_13_14 v.2
Parts LPC111x/102/202/302 added (LPC1100L series).
Power consumption data for parts LPC111x/102/202/302 added in Table 7.
PLL output frequency limited to 100 MHz in Section 7.15.2.
Description of RESET and WAKEUP functions updated in Section 6.
WDT description updated in Section 7.14. The WDT is a 24-bit timer.
Power profiles added to Section 2 and Section 7 for parts LPC111x/102/202/302.
20100818
Product data sheet
-
LPC1111_12_13_14 v.1
•
•
•
VESD limit changed to 6500 V (min) /+6500 V (max) in Table 6.
•
•
•
•
•
•
VDD range changed to 3.0 V  VDD  3.6 V in Table 15.
tDS updated for SPI in master mode (Table 17).
Deep-sleep mode functionality changed to allow BOD and watchdog oscillator as the
only analog blocks allowed to remain running in Deep-sleep mode (Section 7.15.5.3).
Reset state of pins and start logic functionality added in Table 3 to Table 5.
Section 7.16.1 added.
Section “Memory mapping control” removed.
VOH and IOH specifications updated for high-drive pins in Table 7.
Section 9.4 added.
20100416
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
-
© NXP B.V. 2011. All rights reserved.
60 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
16. Legal information
16.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
16.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
61 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
17. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
62 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
18. Contents
1
2
3
4
4.1
5
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 4
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pinning information . . . . . . . . . . . . . . . . . . . . . . 6
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional description . . . . . . . . . . . . . . . . . . 15
ARM Cortex-M0 processor . . . . . . . . . . . . . . . 15
On-chip flash program memory . . . . . . . . . . . 15
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 15
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 15
Nested Vectored Interrupt Controller
(NVIC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5.2
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 17
7.6
IOCONFIG block . . . . . . . . . . . . . . . . . . . . . . 17
7.7
Fast general purpose parallel I/O . . . . . . . . . . 17
7.7.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.8
UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.8.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.9
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 18
7.9.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.10
I2C-bus serial I/O controller . . . . . . . . . . . . . . 18
7.10.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.11
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.11.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.12
General purpose external event
counter/timers . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.12.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.13
System tick timer . . . . . . . . . . . . . . . . . . . . . . 20
7.14
Watchdog timer (LPC1100 series,
LPC111x/101/201/301) . . . . . . . . . . . . . . . . . . 20
7.14.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.15
Windowed WatchDog Timer
(LPC1100L series, LPC111x/102/202/302). . . 21
7.15.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.16
Clocking and power control . . . . . . . . . . . . . . 21
7.16.1
Crystal oscillators . . . . . . . . . . . . . . . . . . . . . . 21
7.16.1.1 Internal RC oscillator . . . . . . . . . . . . . . . . . . . 22
7.16.1.2 System oscillator . . . . . . . . . . . . . . . . . . . . . . 22
7.16.1.3 Watchdog oscillator . . . . . . . . . . . . . . . . . . . . 23
7.16.2
System PLL . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.16.3
Clock output . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.16.4
Wake-up process . . . . . . . . . . . . . . . . . . . . . . 23
7.16.5
7.16.5.1
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
Power profiles (LPC1100L series,
LPC111x/102/202/302 only) . . . . . . . . . . . . . .
7.16.5.2 Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . .
7.16.5.3 Deep-sleep mode. . . . . . . . . . . . . . . . . . . . . .
7.16.5.4 Deep power-down mode . . . . . . . . . . . . . . . .
7.17
System control . . . . . . . . . . . . . . . . . . . . . . . .
7.17.1
Start logic . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.3
Brownout detection . . . . . . . . . . . . . . . . . . . .
7.17.4
Code security
(Code Read Protection - CRP) . . . . . . . . . . .
7.17.5
APB interface . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.6
AHBLite . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.17.7
External interrupt inputs . . . . . . . . . . . . . . . . .
7.18
Emulation and debugging . . . . . . . . . . . . . . .
8
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
9
Static characteristics . . . . . . . . . . . . . . . . . . .
9.1
BOD static characteristics . . . . . . . . . . . . . . .
9.2
Power consumption LPC111x/101/201/301 . .
9.3
Power consumption LPC111x/102/202/302 . .
9.4
Peripheral power consumption . . . . . . . . . . .
9.5
Electrical pin characteristics. . . . . . . . . . . . . .
10
Dynamic characteristics. . . . . . . . . . . . . . . . .
10.1
Power-up ramp conditions . . . . . . . . . . . . . . .
10.2
Flash memory . . . . . . . . . . . . . . . . . . . . . . . .
10.3
External clock. . . . . . . . . . . . . . . . . . . . . . . . .
10.4
Internal oscillators . . . . . . . . . . . . . . . . . . . . .
10.5
I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6
I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.7
SPI interfaces. . . . . . . . . . . . . . . . . . . . . . . . .
11
Application information . . . . . . . . . . . . . . . . .
11.1
ADC usage notes. . . . . . . . . . . . . . . . . . . . . .
11.2
XTAL input . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3
XTAL Printed Circuit Board
(PCB) layout guidelines . . . . . . . . . . . . . . . . .
11.4
Standard I/O pad configuration . . . . . . . . . . .
11.5
Reset pad configuration . . . . . . . . . . . . . . . . .
11.6
ElectroMagnetic Compatibility
(EMC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Package outline. . . . . . . . . . . . . . . . . . . . . . . .
13
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .
15
Revision history . . . . . . . . . . . . . . . . . . . . . . .
16
Legal information . . . . . . . . . . . . . . . . . . . . . .
16.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
23
23
24
24
24
24
24
25
25
25
26
26
26
26
27
28
33
33
36
40
41
44
44
44
45
46
47
47
48
51
51
51
52
53
54
54
55
57
59
60
61
61
continued >>
LPC1111_12_13_14
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 22 June 2011
© NXP B.V. 2011. All rights reserved.
63 of 64
LPC1111/12/13/14
NXP Semiconductors
32-bit ARM Cortex-M0 microcontroller
16.2
16.3
16.4
17
18
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information. . . . . . . . . . . . . . . . . . . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
62
62
63
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2011.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 22 June 2011
Document identifier: LPC1111_12_13_14