APITECH SF0160BA01961S

160 MHz SAW Filter
30 MHz Bandwidth
Part Number: SF0160BA01961S
DESCRIPTION
•
•
•
160 MHz SAW bandpass filter with 30 MHz bandwidth.
13.3 x 6.5 mm LCC package.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal:
Vertical from Top:
S11 (60 to 260 MHz)
Frequency :
Relative Magnitude :
Relative magnitude :
Phase Linearity :
20
10
1
10
MHz/div
dB/div
dB/div
deg/div
S22 (60 to 260 MHz)
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0160BA01961S Rev A 15-Mar-2010
ECN 36650 Page 1 of 3
160 MHz SAW Filter
30 MHz Bandwidth
Part Number: SF0160BA01961S
SPECIFICATION
Parameter
Center Frequency (Fc) 1,3
Insertion Loss
1 dB Bandwidth
3 dB Bandwidth
40 dB Bandwidth
Passband Amplitude Ripple 2
Phase Ripple( Fc +/- 15 MHz) 2
Rejection:
10 - 135 MHz
185 - 280 MHz
270 - 370 MHz
VSWR ( Fc +/- 15 MHz)
Ambient Temperature (Tref)
Notes:
Min
159.75
30
40
40
20
4.4
-
Typ
160.0
12.2
33.0
35.0
44.0
0.8
9
50
50
25
6
25
Max
160.25
14
50
1
12
-
Units
MHz
dB
MHz
MHz
MHz
dB p-p
deg p-p
dB
dB
dB
dB
ºC
1. Average of the lower and upper 3 dB band edge frequencies.
2. When used in the suggested matching network.
3. Typical change of filter frequency response with temperature is ∆f = (T-Tref)*Tc*Fc, in ppm.
MAXIMUM RATINGS
Parameter
Storage Temperature Range
Operating Temperature Range (T)
Temperature Coefficient of Frequency (Tc) 3
Input Power Level
Min
Typ
Max
Units
-40
-20
-
25
25
-94
10
85
70
13
˚C
˚C
ppm/˚C
dBm
MATCHING CIRCUIT
Ls1
Input
50 Ω
Single-ended
12
6
Lp2
Lp1
11
Output
50 Ω
Single-ended
5
Typical component values:
Ls1
Lp1
=
=
47
43
nH
nH
Ls2
=
47
nH
Notes:
1. Recommend use of 2% tolerance matching components. Inductor Q=45.
2. Component values are for reference only and may change depending on board layout.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0160BA01961S Rev A 15-Mar-2010
ECN 36650 Page 2 of 3
160 MHz SAW Filter
30 MHz Bandwidth
Part Number: SF0160BA01961S
PACKAGE OUTLINE
SUGGESTED FOOTPRINT
Units: mm
Tolerances are ±0.15 mm except
where indicated and for the
overall length and width, which
are nominal values.
Pad Configuration:
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm min,
over a 1.3-8.9 µm Ni plating
Input:
Input return:
Output:
Output return:
Ground:
11
12
5
6
All other pads
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0160BA01961S Rev A 15-Mar-2010
ECN 36650 Page 3 of 3