120 MHz SAW Filter 42 MHz Bandwidth Part Number: SF0120BA03167S DESCRIPTION • • • 120 MHz SAW bandpass filter with 42 MHz bandwidth. 7 x 5 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 14 deg/div Delay 150 ns/div Center = 120 MHz, 12 MHz/div (150 kHz incr) S11 (60-180 MHz) S22 (60-180 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0120BA03167S Rev A 22-Feb-2010 ECN 36650 Page 1 of 3 120 MHz SAW Filter 42 MHz Bandwidth Part Number: SF0120BA03167S SPECIFICATION Parameter Min 1 Center Frequency (Fc) Insertion Loss 2 Lower 1 dB Frequency Upper 1 dB Frequency Passband Amplitude Variation 3 Passband Amplitude Variation 4 Phase Deviation from Linear 3 Group Delay Variation 3 Lower 40 dB Frequency Upper 40 dB Frequency Absolute Delay Source and Load Impedance Notes: 141 92 - Typ Max 120 14.7 96.7 142.2 0.85 1.1 8 70 93.5 147.0 0.76 50 18 99 1.2 1.7 14 150 148 1.2 - Units MHz dB MHz MHz dB p-p dB p-p deg p-p ns p-p MHz MHz us Ω 1. Average of lower and upper 3 dB frequencies. 2. Measured at 120 MHz. 3. Evaluated over 100 to 140 MHz. 4. Evaluated over 99 to 141 MHz. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min -40 0 - Max 85 85 +13 Units ˚C ˚C dBm MATCHING CIRCUIT 10 4 Input 50 Ω Single-ended Output 50 Ω Single-ended 12 6 GND GND Typical component values: Lp1 = 100 nH Ls1 = 82 nH Ls2 = 68 nH Cp2 = 21 pF Notes: 1. Recommend +/-2% tolerance matching components. Typical inductor Q=0. 2. Tuning values shown are for reference only. Optimum values may change depending upon board layout Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0120BA03167S Rev A 22-Feb-2010 ECN 36650 Page 2 of 3 120 MHz SAW Filter 42 MHz Bandwidth Part Number: SF0120BA03167S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are ±0.15 mm except where indicated. Pad Configuration: Input: 10 Input Return: 12 Output: 4 Output Return: 6 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0120BA03167S Rev A 22-Feb-2010 ECN 36650 Page 3 of 3