153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S DESCRIPTION • • • 153.6 MHz SAW bandpass filter with 20 MHz bandwidth. 7 x 5 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 5 deg/div Delay 100 ns/div Center = 153.6 MHz, 15 MHz/div (187.5 kHz incr) S11 (78.6-228.6 MHz) S22 (78.6-228.6 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 1 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S SPECIFICATION Parameter Center Frequency, FC 1 Minimum Insertion Loss Passband Ripple (143.6 to 163.6 MHz) Group Delay Deviation (143.6 to 153.6 MHz) Phase Ripple (143.6 to 153.6 MHz) Absolute Delay 1 dB bandwidth 2 Relative Attenuation (10 to 105 MHz) 2 Relative Attenuation (200 to 230 MHz) 2 Relative Attenuation (230 to 1000 MHz) 2 Input Return Loss at Fc Output Return Loss at Fc Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 20 50 52 40 10 10 - Typ 153.6 8.8 0.4 30 3.5 560 23.4 52 55 60 15 18 50 -86 25 Max 12 1 60 5 - - Units MHz dB dB p-p ns p-p deg p-p ns MHz dB dB dB dB dB ohms ppm/˚C ˚C 1. Reference frequency. Computed as mean of the 3 dB frequencies. 2. All dB values are referenced to the insertion loss value. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 - 85 85 10 Units ˚C ˚C dBm MATCHING CIRCUIT 10 5 Input 50 Ω Single ended Output 50 Ω Single ended All other pads GND Ls1 = 138 nH GND Ls2 = 207 nH Cp1 = 22 pF Cp2 = 15 pF Notes: • Recommend 2% or better tolerance matching components. Typical inductor Q=40. • Optimum values may change depending on board layout. Values shown are intended as a guide only. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 2 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S PACKAGE OUTLINE ∆ SMI BA03191S YYDDD Date Code (YY=year, DDD=day) Pad 1 indicator mark (ESD) Units: mm Tolerances are typically ±0.15 mm except where indicated. Pad Configuration: Input: 10 Output: 5 Ground: All other pads SUGGESTED FOORPRINT Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating 2.54 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 3 of 3