PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HYDIS AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST TITLE : HX104X02-100 Preliminary Product Specification Rev. P0 HYDIS TECHNOLOGIES FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 PHONE: (949) 360 5830 E-MAIL: [email protected] Website: www.azdisplays.com SPEC. NUMBER TD-0008369 B2005-C001-C(1/3) PRODUCT GROUP TFT-LCD PRODUCTS REV. P0 ISSUE DATE 2011.09.07 PAGE 1 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 REVISION HISTORY REV. ECN NO. P0 SPEC. NUMBER TD-0008369 B2005-C001-C(2/3) DESCRIPTION OF CHANGES Initial Release DATE PREPARED 11.09.07 C.H.Hwang SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 2 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 CONTENS NO. ITEM PAGE 1.0 General Description 4 2.0 Absolute Maximum ratings 6 3.0 Electrical specifications 7 4.0 Optical specifications 9 5.0 Interface Connection 11 6.0 Signal Timing Specification 15 7.0 Signal Timing waveforms of interface signal (DE mode) 16 8.0 Input Signals, Display Colors & Gray Scale of Colors 17 9.0 Power Sequence 18 10.0 Mechanical Characteristics 19 11.0 Reliability Test 20 12.0 Packing Specifications 21 13.0 Handling & Cautions 25 14.0 EDID Data 26 15.0 Appendix 28 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 3 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 1.0 GENERAL DESCRIPTION 1.1 Introduction 10.4” AFFS+ TFT-LCD is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as active switching devices. This module has a 10.4 inch diagonally measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type. SMD LED Array Gate Driver IC (COG) VDD (3.3V) CN1 Power Block 10.4" XGA T/CON LVDS 1CH (6bit) Source Driver IC (COG) 1.2 Features • • • • • • • • • 1Ch LVDS Interface with 1 pixel / clock 6-bit color depth, Display 262,144 colors High luminance and contrast ratio, low reflection and wide viewing angle Front Mounting Frame DE (Data Enable) mode only SLG (Single Level Gate) function use RoHS Product SMD LED Array On board EDID 1.3 Application • Pen type & Tablet PC SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 4 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 1.3 General Specifications PARAMETER SPECIFICATION UNIT Active area 210.432 X 157.824 mm Number of pixels 1024(H) × 768(V) pixels Pixel pitch 0.2055(H) × 0.2055(V) Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Dimensional outline 238.6±0.5(H) X 173.2±0.5(V) X 4.3max Weight 210 Typ. / 220 Max. Back-light SMD LED Array Surface treatment Anti-Glare REMARK mm colors mm Note 1 gram Note : 1. LCM Height : 4.3mm max. (LED), 6.8mm max. (Component) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 5 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. PARAMETER SYMBOL MIN. MAX. UNIT REMARK Logic Power Supply VDD VSS-0.3 4.0 V Ta = 25 ±2 ℃ Logic Input Voltage VIN VSS-0.3 VDD+0.3 V HVDD -0.3 40 V 25℃ ILED - 30 mA 50℃ ILED - 20 mA Back-light LED Reverse Voltage VR - 5 V Operating Temperature TOP -20 +70 ℃ Back-light Power Supply Voltage Back-light LED Current Note1 Note1. As compromised, T-Con and D-IC are excluded within the range of guarantee for Operating Temperature. *T-CON : 0~70℃ / D-IC : -10 ~ 75℃(Source) / -20 ~ 75℃(Gate) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 6 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Parameter Min. Typ. Max. Unit Remarks Logic Power Supply Voltage VDD 3.0 3.3 3.6 V Note 1 Logic Power Supply Current IDD - 270 300 mA Note 1 Back-light Power Supply Voltage HVDD 7.0 12.0 20 V Note 2 Back-light Power Supply Current IHVDD - 246 283 mA Note 2, 3 PBL - 2.95 3.39 W Note 2, 3 η - 82 - % Note 2, 3 Back-light PWM Frequency FPWM 200 320 350 ㎐ High Level PWM Signal Voltage VPWMH 2.1 3.3 5.0 V Low Level PWM Signal Voltage VPWML - 0 0.6 V High Level Differential Input Signal Voltage VIH - - +100 mV Low Level Differential Input Signal Voltage VIL -100 - - mV Back-light LED Voltage / Back-light LED Total Voltage VLED /VBL - 3.2 / 22.4 3.4 / 23.8 V Note 4 Back-light LED Current / Back-light LED Total Current ILED /IBL - 19.0 /114.0 20.0 / 120.0 mA Note 4 12,000 - - Hrs Note 6 PD - 0.90 1.00 W Note 1 PLED - 2.55 2.85 W Note 4 Ptotal - 3.45 3.85 W Note 1, 4 Back-light Power Consumption LED Driver’s Efficiency Life Time Power Consumption SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification VCM = 1.2V PAGE 7 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25℃. a) Typ : Window XP pattern, b) Max : Vertical Sub line pattern 2. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 3. Reference value, which is measured with LED Driver for 12V. 4. Reference value, which is measured without LED Driver. 5. Calculated value for reference (VLED × ILED × # of LEDs (42EA) ). 6. End of Life shall be determined by the time when any of the following is satisfied under continuous lighting at 25℃ and ILED = 19.0mA. - Intensity drops to 50% of the Initial Value (Luminance Spec.) - Based on LED 3.2 PWM Duty Ratio vs Brightness 100 Relative Brightness (%) 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Duty Ratio (%) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 8 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 4.0 OPTICAL SPECIFICATION The test of Optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25C. Optimum viewing angle direction is 6 o’clock. PARAMETER SYMBOL CONDITION Horizontal Viewing Angle Range Vertical MIN. TYP. MAX. UNIT - 89 - Deg. - 89 - Deg. - 89 - Deg. - 89 - Deg. 400 600 - - 300 - 80 - - 65 - - 0.273 0.313 0.353 0.289 0.329 0.369 xR - T.B.D - yR - T.B.D - xG - T.B.D - - T.B.D - xB - T.B.D - yB - T.B.D - - 40 - % Θ3 Θ9 Θ12 Θ6 Luminance Contrast ratio CR Luminance of White Yw White Luminance Uniformity Center 5 Points ΔY5 13 Points ΔY13 xw White Chromaticity yw Red Reproduction of Color Green Blue CR > 10 yG Θ = 0 Θ = 0 Θ = 0 Θ = 0 Color Reproduction Response Time Cross Talk SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) REMARK Note 1 Note 2 cd/m2 Note 3 Note 4 Note 5 Tr +Td Ta= 25 C Θ = 0 - 36 - ms Note 6 CT Θ = 0 - - 2.0 % Note 7 SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 9 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface . (see FIGURE 1) 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. Luminance of white is defined as a luminance value of a point across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed. (See FIGURE 2) Uniformity ΔY = Minimum Luminance of 5(or 13) points Maximum Luminance of 5(or 13) points X 100 (%) 5. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electro-optical response time measurements shall be made as FIGURE 3 by switching the data input signal OFF and ON. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 ). SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 10 / 31 A4(210 X 297) 5.0 PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 INTERFACE CONNECTION. 5.1 Electrical Interface Connection CN1 : Interface Connector : 20455-030E-02(I-PEX) or equivalent User side Connector : 20453-030T (I-PEX) or equivalent Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) Symbol VSS VDD1 VDD2 EDID 3.3V NC EDID CLK EDID DATA RIN0RIN0+ VSS RIN1RIN1+ VSS RIN2RIN2+ VSS RCLKINRCLKIN+ VSS VDIM VSW VSS VSS VSS VSS VCD1 VCD2 VCD3 VCD4 VSS Function Ground Power Supply: +3.3V Power Supply: +3.3V EDID +3.3V Reserved EDID CLK EDID DATA LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative clock signal (-) LVDS Positive clock signal (+) Ground PWM Brightness Control LED On/Off Control Ground Ground Ground Ground Back-light Power Supply: +12V Back-light Power Supply: +12V Back-light Power Supply: +12V Back-light Power Supply: +12V Ground SPEC. TITLE HX104X02-100 Preliminary Product Specification Remark Tx pin # 48 Tx pin # 47 Tx pin # 46 Tx pin # 45 Tx pin # 42 Tx pin # 41 Tx pin # 40 Tx pin # 39 HVDD: 7~20V PAGE 11 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 [ LVDS Block Diagram ] 5.1.1 INTERFACE CONNECTION SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 12 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 5.2. LVDS Interface LVDS Transmitter: THC63LVDM83A or equivalent. TRANSMITTER INTERFACE INPUT SIGNAL PIN NO. PIN NO. SYSTEM (TX) TFT-LCD (RX) R0 R1 51 52 R2 54 R3 55 R4 56 R5 3 G0 4 G1 6 G2 7 G3 11 G4 12 G5 14 B0 15 B1 19 B2 20 B3 22 B4 23 B5 24 HSYNC 27 VSYNC 28 DE 30 MCLK 31 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) FI-XB30S-HF10 PIN NO. 48 47 OUT0OUT0+ IN0IN0+ 8 9 46 45 OUT1OUT1+ IN1IN1+ 11 12 42 41 OUT2OUT2+ IN2IN2+ 14 15 40 CLKOUT- CLKIN- 17 39 CLKOUT+ CLKIN+ 18 SPEC. TITLE HX104X02-100 Preliminary Product Specification REMARK PAGE 13 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 5.3 Back-light Interface CN2 LED FPC Connector (20397-008E, Manufactured by I-PEX ) Pin No. Symbol Function 1 Anode1 2 NC 3 Cathode1 LED Cathode Power Supply 4 Cathode2 LED Cathode Power Supply 5 Cathode3 LED Cathode Power Supply 6 Cathode4 LED Cathode Power Supply 7 Cathode5 LED Cathode Power Supply 8 Cathode6 LED Cathode Power Supply LED Anode Power Supply Remark LED Anode Power Supply (3.2V X 7 EA = 22.4V) Non-Connection LED Cathode Power Supply 5.4. Data Input Format (1,1) (1,2) (1023,1) (1024,1) R G B R G B R G B R G B 1 Pixel = 3 Dots R G B R G B R G B (1,768) (2,768) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) R G B R G B Display position of input data (1023,768) (1024,768) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 14 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 6.0. SIGNAL TIMING SPECIFICATIONS 6.1 LVDS Transmitter Input The 10.4” XGA LCM is operated by the only DE (Data enable) mode (LVDS Transmitter Input) ITEM SYMBOL MIN TYP MAX UNIT Frame Period T1 772 806 - lines Vertical Display Period T2 - 768 - lines One Line Scanning Period T3 1100 1344 - clocks Horizontal Display Period T4 - 1024 - clocks 1/T5 - 65 80 MHz Clock Frequency 6.2. LVDS Rx interface timing parameter ITEM SYMBOL MIN TYP MAX UNIT CLKIN Period tRCIP 12.5 15.38 - nsec Input Data 0 tRIP1 -0.4 0.0 +0.4 nsec Input Data 1 tRIP0 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP6 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP5 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP3 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP2 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec REMARK tRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RxINz +/* Z = 0, 1, 2,3 RxCLKIN+/- SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) Rx3 Rx2 Rx1 Rx0 Rx6 Vdiff=0[v] Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Vdiff=0[v] tRCIP SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 15 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL (DE MODE) 7.1 Timing Waveforms of Interface Signal T1 T2 DE T3 DCLK T5 T4 DE DATA SIGNALS SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) Valid display data (1024 Clocks) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 16 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data. COLORS & GRAY SCALE Basic Colors Gray Scale Of Red Gray Scale Of Green Gray Scale Of Blue Gray Scale Of White & Black RED DATA GREEN DATA BLUE DATA R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Darker 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 △ ↓ ▽ ↓ ↓ ↓ ↓ ↓ Brighter 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ▽ 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Darker 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 △ ↓ ▽ ↓ ↓ ↓ ↓ ↓ Brighter 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 ▽ 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 △ ↓ ▽ ↓ ↓ ↓ ↓ ↓ Brighter 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 ▽ 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 Darker 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 △ ↓ ↓ ↓ ▽ ↓ ↓ ↓ Brighter 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 ▽ 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 17 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 9.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below Power Supply 0.9VDD 0.1VDD 0.9VDD 0.1VDD 0V T1 T5 T2 Interface Signal Valid 0 T3 Back- light Parameter T6 T4 0 Values Units Min Typ Max T1 0 - 10 ms T2 0 - 50 ms T3 100 - - ms T4 100 - - ms T5 0 - 50 ms T6 1 - - Sec Notes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 18 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements FIGURE 5, 6 shown in appendix shows mechanical outlines for the model. PARAMETER SPECIFICATION UNIT Active area 210.432 (H) × 157.824 (V) mm Number of pixels 1024 (H) × 768 (V) (1 pixel = R + G + B dots) pixels Pixel pitch 0.2055 (H) × 0.2055 (V) Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Dimensional outline 238.6±0.5 (W) X 173.2±0.5 (V) X 4.3 Max. (LED), 6.8 Max. (Component) Weight 210 Typ. / 220 Max. Back-light SMD LED Arrary mm colors mm g 10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Anti-Glare Polarizer. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50 cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable. SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 19 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 11.0 RELIABLITY TEST NO TEST ITEMS CONDITIONS 1 High temperature storage test Ta = 80 C, 240 hrs 2 Low temperature storage test Ta = -20 C, 240 hrs 3 High temperature & high humidity operation test Ta = 50 ℃, 80%RH, 240hrs 4 High temperature operation test Ta = 70 C, 240 hrs 5 Low temperature operation test Ta = 0 C, 240 hrs 6 Thermal shock Ta = -20 C ~ 80 C (0.5H), 100 cycle 7 Vibration test (non-operating) Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min 8 Shock test (non-operating) Gravity : 220G Pulse width : 2ms, half sine wave ±X, ±Y, ±Z Once for each direction 9 Electro-Static Discharge Test (non-operating) Air : 150pF, 330ohm, 15KV Contact : 150pF, 330ohm, 8KV SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 20 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 12.0 PACKING SPECIFICATION 12.1 Packing Order Hydis provides the standard shipping container for customers, unless customer specifies their packing information. The standard packing method is shown in below. Put Pad into the box. Put silica gels in the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. As shown in the figure, place the Modules bundled by shielding bag in the box. Notes Box Dimension: 349.0mm(W) X 261.0mm(D) X 311.0mm(H) Package Quantity in one Box: 10pcs SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 21 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 12.2 Pallet Packing * Note Pallet Dimension : : 1100 mm (L) 1100 mm (W) 120 mm (H) Package Quantity in one Box : 10pcs Box Quantity in one Pallet : 36 box SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 22 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 12.3 Packing Label Label Size: 108 mm (L) 56 mm (W) Contents Model: HX104X02-100 Q`ty: Module Q`ty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product MODEL : HX104X02-100 Q’TY : 10 SERIAL NO. : 0000000000000 DATE : XXXX. XX. XX 00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) FG CODE SPEC. TITLE HX104X02-100 Preliminary Product Specification RoHS Mark PAGE 23 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 12.3 Product Label 0 1 HX104X02-100 HYDIS Barcode 1 2 3 4 5 X X X X X X X 6 7 X X X X X X X X X X No 1. Control Number No 5. Month (1, 2, 3,…, 9, X, Y, Z) No 2. Rank / Grade No 6. FG Code No 3. Line Classification (HYDIS : H) No 7. Serial Number No 4. Year (8 : 2008, 9 : 2009, …) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 24 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 13.0 HANDLING & CAUTIONS 13.1 Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and backlight element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. 13.3 Cautions for the operation When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence were applied, the module would be damaged. 13.4 Cautions for the atmosphere Dewdrop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer-packing pouch and under relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. 13.6 Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc, please pack the module not to be broken. We recommend using the original shipping packages. SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 25 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 14.0 EDID Data Add Function Hex Input Value Add Function Hex Input Value 00 00 20 BLue y high bits 21 01 FF 21 White x high bits 50 0.313 02 FF 22 White y high bits 54 0.329 23 Established timing 1 21 24 Established timing 2 08 Established timing 3 00 03 04 Header FF FF EDID 05 FF 25 06 FF 26 07 00 27 08 09 0A 0B ID Manufacturer Name ID Product Code 09 E5 00 40 ID 10.4XGA 28 29 2A 2B 0C 00 2C 0D 00 2D 00 2E 00 2F 0E 32-bit serial No. 0F Standard timing #1 Standard timing #2 Standard timing #3 Standard timing #4 Standard timing #5 01 01 01 01 01 30 11 Year of Manufacture 13 2009 31 12 EDID Structure Ver. 01 1 32 13 EDID revision # 03 3 33 14 Video input definition 80 15 Max H image size 15 21 35 16 Max V image size 10 16 36 64 17 Display Gamma 78 2.2 37 19 18 Feature support EA RGB mode 38 00 19 Red/Green low bits BD 39 01 01 01 30 3A 1B Red x high bits 91 3B 1C Red y high bits 54 3C 26 1D Green x high bits 4F 3D 30 1E Green y high bits 8B 3E 18 1F Blue x high bits 26 3F 88 TD-0008369 B2005-C001-C(3/3) Not Used 01 Blue/White low bits SPEC. TITLE HX104X02-100 Preliminary Product Specification Not Used 01 1A SPEC. NUMBER Not Used 01 40 Detailed timing / monitor descriptor #1 Not Used 01 0 Standard timing #8 Not Used 01 00 34 Not Used 01 Week of manufacture Standard timing #7 Not Used 01 10 Standard timing #6 Not Used 01 41 00 . . . . . . . . . . . Main clock : 65.0MHz Hor. Active : 1024 Hor. Blanking : 320 4 bits of Hor. Active + 4 bits of Hor. Blanking Ver. Active : 768 Ver. Blanking : 38 4 bits of Ver. Active + 4 bits of Ver. Blanking Hor. Sync Offset : 24 H sync Pulse Width:136 V sync Offset : 1 line V Sync Pulse width : 3 line PAGE 26 / 31 A4(210 X 297) Add Function 41 00 42 44 REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Input Value 36 40 43 Hex PRODUCT GROUP D2 Detailed timing / monitor descriptor #1 9E 00 . Horizontal Image Size : 210 mm (Low 8 bits) . Vertical Image Size : 158 mm (Low 8 bits) . 4 bits of Hor. Image Size + 4 bits of Ver. Image Size . Hor. Border : 0 pixel . Vertical Border : 0 line Add Function Hex 60 59 61 44 62 49 63 53 64 0A Detailed timing / monitor descriptor #3 45 00 46 00 47 18 67 20 48 28 68 20 49 15 69 20 4A 00 6A 20 4B 40 6B 20 4C 41 6C 00 4D 00 6D 00 4E 26 6E 00 4F 30 6F FE 18 70 00 88 71 48 52 36 72 58 53 00 73 50 51 Detailed timing / monitor descriptor #2 65 66 20 20 D2 74 55 9E 75 56 00 76 58 57 00 77 30 58 00 78 31 59 18 79 2D 5A 00 7A 32 00 7B 31 00 7C 30 FE 7D 0A 5E 00 7E Extension flag 00 5F 48 7F Checksum A7 5C 5D Detailed timing / monitor descriptor #3 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) Company name : HYDIS 31 Detailed timing / monitor descriptor #4 54 5B Input Value SPEC. TITLE HX104X02-100 Preliminary Product Specification 30 34 Model name : HX104X01-210 PAGE 27 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 15.0 APPENDIX Figure 1. Measurement Set Up (L = 50cm) <Indoor> Figure 2. Average Luminance Measurement Locations & Uniformity Measurement Locations 10mm 7 6 192 384 2 9 4 Lines 10mm 11 10 5 13 12 10mm X TD-0008369 B2005-C001-C(3/3) 3 1 576 SPEC. NUMBER 8 256 512 768 Pixels 10mm : Test Point SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 28 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Figure 3. Response Time Testing TFT Off (Black) TFT On (White) TFT Off (Black) Tr Td 100% 90% 10% 0% Time Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA 256, 192 256, 576 768,192 768,576 YB (896,384) YA (896, 384) YB - YA Cross-Talk = YA × 100 Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns. SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 29 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Figure 5. TFT-LCD Module Outline Dimensions (Front View) SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 30 / 31 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT P0 2011.09.07 Figure 5. TFT-LCD Module Outline Dimensions (Rear View) HX104X02-100 10 SPEC. NUMBER TD-0008369 B2005-C001-C(3/3) SPEC. TITLE HX104X02-100 Preliminary Product Specification PAGE 31 / 31 A4(210 X 297)