PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE TFT-LCD SBU AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE TFTLCD SBU AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST TITLE : HT190E01-100 Product Specification Rev. B BOE TFT-LCD SBU BEIJING BOE OPTOELECTRONICS TECHNOLOGY BOE HYDIS TECHNOLOGY SPEC. NUMBER S864-1221 B2005-C001-O(1/3) PRODUCT GROUP TFT-LCD REV. B ISSUE DATE 2005.09.08 PAGE 1 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 DATE PREPARED REVISION HISTORY REV. ECN No. 0 DESCRIPTION OF CHANGES Initial Release 05.04.22. W.K. Chang A E0506-F001 Weight : 2150 g max. Æ 2050 g max. 05.05.31 W.K.Chang B E0508-F019 1.Add View Angle Spec at CR>5 05.09.08 W.K.Chang : 80/80/80/80 Typ. 70/70/70/70 Min. 2.Divide Response Time Spec from Total into Rising and Falling - Rising : 2 ms Typ. 4 ms Max. - Falling : 6 ms Typ. 8 ms Max. SPEC. NUMBER S864-1221 B2005-C001-O(2/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 2 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 Contents No. Item Page 1.0 General Description 4 2.0 Absolute Maximum Ratings 6 3.0 Electrical specifications 7 4.0 Optical specifications 8 5.0 Interface Connection 10 6.0 Signal Timing Specifications 14 7.0 Signal Timing waveforms of Interface Signal 16 8.0 Input Signals, Display Colors & Gray Scale of Colors 18 9.0 Power Sequence 19 10.0 Mechanical Characteristics 20 11.0 Reliability Test 21 12.0 Handling & Cautions 22 13.0 Product Serial Number 23 14.0 Packing 24 15.0 Appendix 26 SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 3 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 1.0 GENERAL DESCRIPTION 1.1 Introduction HT190E01-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 19.0 inch diagonally measured active area with SXGA resolutions (1280 horizontal by 1024 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16,194,227 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. CN21 CN22 LVDS Input Signal Source Driver VDD 1 Gate Driver Connector (CN LVDS Rx + T/CON + mini-LVDS Tx ) DC/DC Gamma Vcom TFT LCD Panel 1280 ×1024 CN23 CN24 1.2 Features z LVDS Interface with 2 pixel / clock z High-speed response z Low power consumption z 6-bit (FRC) color depth, display 16,194,227 colors z Incorporated edge type back-light (Four lamps) z High luminance and contrast ratio, low reflection and wide viewing angle z DE (Data Enable) & H-Sync & V-Sync mode z RoHS Compliant SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 4 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 1.3 Application z Desktop Type of PC & Workstation Use z Slim-Size Display for Stand-alone Monitor z Display Terminals for Control System z Monitors for Process Controller 1.4 General Specification The followings are general specifications at the model HT190E01-100. <Table 1. General Specifications> Parameter Specification Unit Active area 376.32(H) * 301.06(V) Number of pixels 1280(H) ×1024(V) pixels Pixel pitch 0.294(H) ×0.294(V) mm Pixel arrangement RGB Vertical stripe Display colors 16,194,227 Display mode Normally White Dimensional outline 396.0(H) × 324.0(V) × 16.5(D) typ. Weight 2050 (max.) Surface Treatment Haze 25%, 3H Back-light Top/Bottom edge side, 4-CCFL type SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification Remarks mm colors mm g PAGE 5 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE B 2005.09.08 TFT- LCD PRODUCT 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS=GND=0V] Symbol Min. Max. Unit Remarks Power Supply Voltage VDD VSS-0.5 6.5 V Logic Supply Voltage VIN VSS-0.3 VDD+0.3 V Back-light Lamp Current IBL 3 8 mA Back-light Lamp frequency FL 30 80 kHz Operating Temperature TOP 0 +50 ℃ 1) Storage Temperature TST -20 +60 ℃ 1) Parameter Ta = 25 ℃ Note : 1) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 OC max. and no condensation of water. 100 90 Relative Humidity (%RH) 80 60 O p e ra tin g R a n g e 40 20 S to ra g e R a n g e 5 -2 0 0 20 40 60 80 T e m p e ra tu re (˚ C) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 6 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE B 2005.09.08 TFT- LCD PRODUCT 3.0 ELECTRICAL SPECIFICATIONS 3.1Electrical Specifications [Ta =25±2 ℃] < Table 3. Electrical specifications > Parameter Min. Typ. Max. Unit Power Supply Voltage VDD 4.5 5.0 5.5 V Power Supply Current IDD - 600 900 mA Permissible Input Ripple Voltage VRF 100 mV High Level Differential Input Threshold Voltage VIH +100 mV Remarks Note1 - VDD = 5.0V Vcm = 1.2V typ. Low Level Differential Input Threshold Voltage VIL -100 - Back-light Lamp Voltage VBL 610 620 770 Vrms Back-light Lamp Current IBL 3.0 7.5 8.0 mArms Back-light Lamp operating Frequency FL 30 - 70 KHz Note 2 1400 Vrms 25℃, Note 3 1700 Vrms 0℃, Note 3 Hrs IBL= 8.0mA mV Lamp Start Voltage Lamp Life 50000 PD Power Consumption - 3.0 4.5 W PBL 18.6 Å W Ptotal 21.6 23.1 W IBL=7.5mA, Note 4 Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz and Clock frequency = 67.5MHz. Test Pattern of power supply current a) Typ : Color Bar pattern b) Max : Dot pattern 2. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 3. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the lamps may not be turned on. 4. Calculated value for reference (VBL × IBL) ×4 excluding inverter loss. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 7 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 4.0 OPTICAL SPECIFICATION 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock. 4.2 Optical Specifications [VDD = 5.0V, Frame rate = 60Hz, Clock = 54MHz, IBL = 7.5mA, Ta =25±2 ℃] Parameter Symbol Horizontal Viewing Angle range Vertical Horizontal Viewing Angle range Vertical Luminance Contrast ratio Condition Min. Typ. Max. Unit 65 75 - Deg. 65 75 - Deg. 65 75 - Deg. Θ6 50 60 - Deg. Θ3 70 80 - Deg. 70 80 - Deg. 70 80 - Deg. Θ6 70 80 - Deg. CR 550 700 Θ3 Θ9 Θ12 Θ9 Θ12 Remark CR > 10 Note 1 CR > 5 Note 2 2 Luminance of White Yw 250 300 cd/m Note 3 White luminance uniformity ΔY 75 80 % Note 4 0.283 0.313 0.343 0.299 0.329 0.359 0.609 0.639 0.669 0.309 0.339 0.369 0.249 0.279 0.309 White Wx Wy Rx Red Reproduction of color Response Time Cross Talk SPEC. NUMBER S864-1221 B2005-C001-O(3/3) Ry Gx Θ = 0° (Center) Normal Viewing Angle Green Gy 0.571 0.601 0.631 Blue Bx 0.111 0.141 0.171 By 0.048 0.078 0.108 Note 5 Rising Tr 2 4 ms Falling Tf 6 8 ms - 2.0 CT Note 6 - SPEC. TITLE HT190E01-100 Product Specification % Note 7 PAGE 8 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 Note : 1. 2. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR 3. 4. 5. 6. 7. = Luminance when displaying a white raster Luminance when displaying a black raster Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100 (See FIGURE 2 shown in Appendix). The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix). SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 9 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT 5.0 REV ISSUE DATE B 2005.09.08 INTERFACE CONNECTION. 5.1 Electrical Interface Connection ● CN11 Module Side Connector : JAE FI-XB30SSRL-HF16 or Equivalent User Side Connector : JAE FI-X30H or Equivalent Pin No Symbol Function Remark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RXO0RXO0+ RXO1RXO1+ RXO2RXO2+ GND RXOCLKRXOCLK+ RXO3RXO3+ RXE0RXE0+ GND RXE1RXE1+ GND RXE2RXE2+ RXECLKRXECLK+ RXE3RXE3+ GND NC NC NC VDD VDD VDD LVDS ODD 0- SIGNAL LVDS ODD 0+ SIGNAL LVDS ODD 1- SIGNAL LVDS ODD 1+ SIGNAL LVDS ODD 2- SIGNAL LVDS ODD 2+ SIGNAL GROUND LVDS ODD CLOCK- SIGNAL LVDS ODD CLOCK+ SIGNAL LVDS ODD 3- SIGNAL LVDS ODD 3+ SIGNAL LVDS EVEN 0- SIGNAL LVDS EVEN 0+ SIGNAL GROUND LVDS EVEN 1- SIGNAL LVDS EVEN 1+ SIGNAL GROUND LVDS EVEN 2- SIGNAL LVDS EVEN 2+ SIGNAL LVDS EVEN CLOCK- SIGNAL LVDS EVEN CLOCK+ SIGNAL LVDS EVEN 3- SIGNAL LVDS EVEN 3+ SIGNAL GROUND NO CONNECTION NO CONNECTION NO CONNECTION Note 1 Internal Use Internal Use Internal Use POWER SUPPLY ( +5.0 V ) Note 1 : This pin should be connected with GND. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 10 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 5.2 LVDS Interface (Tx; THC63LVDF83A or Equivalent) 5.2.1 ODD LVDS Interface Input Signal O D D L V D S Transmitter Pin No. OR0 OR1 OR2 OR3 OR4 OR5 OG0 OG1 OG2 OG3 OG4 OG5 OB0 OB1 OB2 OB3 OB4 OB5 Hsync Vsync DE MCLK 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 31 OR6 OR7 OG6 OG7 OB6 OB7 RSVD 50 2 8 10 16 18 25 SPEC. NUMBER S864-1221 B2005-C001-O(3/3) Interface FI-XB30SSRLHF16 Pin No. System (Tx) TFT-LCD (Rx) Pin No. 48 47 OUT0OUT0+ RXO0RXO0+ 1 2 46 45 OUT1OUT1+ RXO1RXO1+ 3 4 42 41 OUT2OUT2+ RXO2RXO2+ 5 6 40 39 CLK OUTCLK OUT+ RXO CLKRXO CLK+ 8 9 38 37 OUT3OUT3+ RXO3RXO3+ SPEC. TITLE HT190E01-100 Product Specification Remark 10 11 PAGE 11 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 5.2.2 EVEN LVDS Interface Input Signal E V E N L V D S Transmitter Pin No. ER0 ER1 ER2 ER3 ER4 ER5 EG0 EG1 EG2 EG3 EG4 EG5 EB0 EB1 EB2 EB3 EB4 EB5 Hsync Vsync DE MCLK 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 31 ER6 ER7 EG6 EG7 EB6 EB7 RSVD 50 2 8 10 16 18 25 SPEC. NUMBER S864-1221 B2005-C001-O(3/3) Interface FI-XB30SSRLHF16 Pin No. System (Tx) TFT-LCD (Rx) Pin No. 48 47 OUT0OUT0+ RXE0RXE0+ 12 13 46 45 OUT1OUT1+ RXE1RXE1+ 15 16 42 41 OUT2OUT2+ RXE2RXE2+ 18 19 40 39 CLK OUTCLK OUT+ RXE CLKRXE CLK+ 20 21 38 37 OUT3OUT3+ RXE3RXE3+ SPEC. TITLE HT190E01-100 Product Specification Remark 22 23 PAGE 12 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 5.3 Data Input Format ODD (1,1) EVEN (2,1) (1279,1) R G B R G B (1280,1) R G B R G B 1 Pixel = 3 Dots R G B R G B R G B R G B R G B (1,1024) (2,1024) (1279,1024) (1280, 1024) Display Position of Input Data (V-H) 5.4 Back-light Interface Connection ●CN 21,22,23,24 Module Side Connector :35001HS-02L(YeonHo) or Equivalent User Side Connector :35001HS-02L(YeonHo) or Equivalent PIN NO. INPUT COLOR FUNCTION 1 HOT Pink & Blue High Voltage 2 COLD Black & White Ground SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 13 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE B 2005.09.08 TFT- LCD PRODUCT 6.0 SIGNAL TIMING SPECIFICATION 6.1 The HT190E01-100 is operated by the DE & H-Sync & V-Sync mode ( LVDS Transmitter Input ) Item Symbols Min Typ Max Unit Frequency 1/Tc 40 54 68 MHz High Time T6 5 - - ns Low Time T7 5 - - ns Setup time T8 4 - - ns Hold time T9 4 - - ns Data Enable Setup Time Tes 4 - - ns Frame Period Ty 1032 1066 1536 lines 13.33 16.67 - ms Clock Data Vertical Display Period Tyd - 1024 - lines One line Scanning Period T3 672 844 1022 clocks Horizontal Display Period T4 640 640 640 clocks SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 14 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 6.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. <Table 4. LVDS Rx Interface Timing Specification> Item Symbol Min Typ Max Unit CLKIN Period tRCIP 14.7 18.5 - msec CLK Difference tCdiff -tRCIP*(3/7) 0 +tRCIP*(3/7) nsec Input Data 0 tRIP1 -0.4 0.0 +0.4 nsec Input Data 1 tRIP0 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP6 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP5 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP3 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP2 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec Remark tRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RXO/Ez +/* Z = 0, 1, 2,3 Rx3 Rx2 Rx1 RxOCLKIN+ Vdiff=0[v] RxECLKIN+ tCdiff Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 tRCIP Rx1 Rx0 Vdiff=0[v] * Vdiff = (RXO/Ez+)-(RXO/Ez-),…. ,(RXO/ECLK+)-(RXO/ECLK-) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 15 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL 7.1 Sync Timing Waveforms Over 3 H-sync V-Sync H-Sync Fix H-Sync width Area DE 1) Need over 3 H-sync during V-Sync Low 2) Fix H-Sync width from V-Sync falling edge to first rising edge 7.2 Horizontal Timing Waveforms Tv Tvd MCLK Th DE R7 ~ R0 G7 ~ G0 B7 ~ B0 Invalid Data SPEC. NUMBER S864-1221 B2005-C001-O(3/3) x,1 x,2 x,y x,1024 Invalid SPEC. TITLE HT190E01-100 Product Specification Data x+1,1 PAGE 16 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 7.3 Horizontal Timing Waveforms Th Thd MCLK Tc DE RA7 ~RA0 GA7 ~GA0 BA7 ~BA0 D1 D2 D638 Dn Tch D639 D640 Invalid Dat a D1 D2 D3 Tcl 2.0V 1.5V MCLK Data Tds Tdh Valid Data 0.8V 2.0V 0.8V Tes DE SPEC. NUMBER S864-1221 B2005-C001-O(3/3) 2.0V SPEC. TITLE HT190E01-100 Product Specification PAGE 17 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Color & Gray Scale Basic Colors Gray Scale of RED Gray Scale of GREEN Gray Scale of BLUE Gray Scale of WHITE Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White SPEC. NUMBER S864-1221 B2005-C001-O(3/3) R7 0 0 0 0 1 1 1 1 0 0 0 R6 0 0 0 0 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 RED DATA R5 R4 R3 R2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 R1 0 0 0 0 1 1 1 1 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 GREEN DATA R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 0 1 1 1 1 1 1 0 1 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 1 1 1 1 1 1 1 0 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 SPEC. TITLE HT190E01-100 Product Specification B6 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 BLUE DATA B5 B4 B3 B2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 1 1 1 1 1 1 B1 0 1 0 1 0 1 0 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 1 0 0 1 1 0 1 0 1 0 0 1 1 0 1 1 PAGE 18 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 9.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below 0.9VDD Power Supply 0V 0.9VDD 0.1VDD 0.1VDD T1 T5 T6 T2 Interface Signal Valid 0V T3 Back- light T4 0V ● T1 ≤ 10 ms ● 0 ≤ T2 ≤ 50 ms ● 200ms ≤ T3 ● 200ms ≤ T4 ● 0 ≤ T5 ≤ 50ms ● 1sec ≤ T6 Notes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 19 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT190E01-100. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters> Parameter Specification Unit Dimensional outline 396.0 ×324.0×16.5 mm Weight 2050 (max.) gram Active area 376.32(H) * 301.06(V) mm Pixel pitch 0.294(H) ×0.294(V) mm Number of pixels 1280(H) ×1024(V) (1 pixel = R + G + B dots) Back-light Top / Bottom edge side 4-CCFL type pixels 10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350lux. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 20 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE B 2005.09.08 TFT- LCD PRODUCT 11.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters > No Test Items Conditions 1 High temperature storage test Ta = 60 ℃, 240 hrs 2 Low temperature storage test Ta = -20 ℃, 240 hrs 3 High temperature & high humidity operation test Ta = 50 ℃, 80%RH, 240hrs 4 High temperature operation test Ta = 50 ℃, 240hrs 5 Low temperature operation test Ta = 0 ℃, 240hrs 6 Thermal shock Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle 7 Vibration test (non-operating) 8 9 Shock test (non-operating) Electro-static discharge test (non-operating) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) Frequency 10 ~ 300 Hz, Sweep rate 30 min Gravity / AMP 1.5 G Period ±X, ±Y, ±Z 30 min Gravity 50G Pulse width 11msec, sine wave Direction ±X, ±Y, ±Z Once for each Air : 150 pF, 330Ω, 15 KV Contact : 150 pF, 330Ω, 8 KV SPEC. TITLE HT190E01-100 Product Specification PAGE 21 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 12.0 HANDLING & CAUTIONS (1) Cautions when taking out the module y Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module y As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. y As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. (3) Cautions for the operation y When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. y Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking. (6) Other cautions y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. yWhen returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 22 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 13.0 PRODUCT SERIAL NUMBER SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 23 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 14.0 Packing 14.1 Packing Order Put Pad into the box. Put silica gels in the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification As shown in figure, place Modules bundled shielding bag in box. the the by the PAGE 24 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 14.2 Packing Note y Box Dimension : 346mm(W) × 526mm(D) × 448mm(H) y Package Quantity in one Box : 7pcs 14.3 Box label y Label Size : 108 mm (L) × 56 mm (W) y Contents Model : HT190E01 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product 7 HT190E01- ### 0000000000000 00 Type 0 0 00 0 Grade Line Year Month SPEC. NUMBER S864-1221 B2005-C001-O(3/3) 2005.02.22. 0 00000 ITEM-CODE Serial_no SPEC. TITLE HT190E01-100 Product Specification FG CODE PAGE 25 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 15.0 APPENDIX Figure 1. Measurement Set Up (L = 5 0 c m ) Figure 2. White Luminance and Uniformity Measurement Locations (5 points) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 26 OF 29 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE B 2005.09.08 TFT- LCD PRODUCT Figure 3. Response Time Testing Display data White(TFT OFF) White(TFT OFF) Black(TFT ON) TR Optical Response TF 100% 90% 10% 0% Time Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA 320,256 960,256 YB(1120, 512) L31 320,768 960,768 YA (1120,512) Cross-Talk (%) = L0 YB - YA × 100 YA Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 27 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 Figure 5. TFT-LCD Module Outline Dimensions (Front view) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 28 OF 29 A4(210 X 297) PRODUCT GROUP TFT- LCD PRODUCT REV ISSUE DATE B 2005.09.08 Figure 6. TFT-LCD Module Outline Dimensions (Rear view) SPEC. NUMBER S864-1221 B2005-C001-O(3/3) SPEC. TITLE HT190E01-100 Product Specification PAGE 29 OF 29 A4(210 X 297)