DS1347 Low-Current, SPI-Compatible Real-Time Clock General Description Features The DS1347 SPI-compatible real-time clock (RTC) contains a real-time clock/calendar and 31 x 8 bits of static random-access memory (SRAM). The real-time clock/calendar provides seconds, minutes, hours, day, date, month, year, and century information. A time/date programmable polled ALARM is included in the device. The end-of-the-month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24hr or 12hr format with an AM/PM indicator. The device operates with a supply voltage of +2V to +5.5V, are available in the ultra-small 8-pin TDFN package, and work over the -40°C to +85°C industrial temperature range. o RTC Counts Seconds, Minutes, Hours, Day of Week, Date of Month, Month, Year, and Century o Leap-Year Compensation o +2V to +5.5V Wide Operating Voltage Range o SPI (Mode 1 or 3) Interface: 4MHz at 5V, 1MHz at 2V o 31 x 8-Bit SRAM for Scratchpad Data Storage o Uses Standard 32.768kHz Watch Crystal o Low Timekeeping Current (400nA at 2V) o Single-Byte or Multiple-Byte (Burst Mode) Data Transfer for Read or Write of Clock Registers or SRAM o Ultra-Small, 3mm x 3mm x 0.8mm, 8-Pin TDFN Package o Programmable Time/Date Polled ALARM Function o No External Crystal Bias Resistors or Capacitors Required Applications Point-of-Sale Equipment Intelligent Instruments Fax Machines Battery-Powered Products Typical Operating Circuit Portable Instruments +3.3V 0.1µF Ordering Information PART DS1347T+ TEMP RANGE OSC CL (pF) -40°C to +85°C 12.5 6 PIN-PACKAGE VCC +3.3V 8 TDFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. DS1347 1 µc 5 2 3 SCLK X1 X2 8 7 32.768kHz CRYSTAL CS DOUT DIN GND 4 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. 19-6007; Rev 3; 1/13 DS1347 Low-Current, SPI-Compatible Real-Time Clock ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V All Other Pins to GND ................................-0.3V to (VCC + 0.3V) Current into Any Pin..........................................................±20mA Rate of Rise, VCC ............................................................100V/µs Continuous Power Dissipation (TA = +70°C) TDFN (derate 24.4mW/°C above +70°C)...................1.375mW Junction Temperature .....................................................+150°C Storage Temperature Range…………………… -55°C to +125°C ESD Protection (All Pins, Human Body Model)................±2000V Lead Temperature (soldering, 10s) .................................+300°C Soldering Temperature (reflow) .......................................+260°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = +2.0V to +5.5V, TA = -40°C to +85°C. Typical values are at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL Operating Voltage Range VCC Active Supply Current (Note 2) ICC Timekeeping Supply Current (Note 3) ITK CONDITIONS MIN TYP 2 MAX UNITS 5.5 V VCC = +2V 0.1 VCC = +5V 0.25 VCC = +2V 0.35 VCC = +3.6V 0.35 0.7 VCC = +5V 0.4 0.8 mA 0.7 μA SPI DIGITAL INPUTS (SCLK, DIN, CS) Input High Voltage VIH Input Low Voltage VIL Input Leakage Current I IL VCC = +2V 1.4 VCC = +5V 2.2 VCC = +2V 0.6 VCC = +5V 0.8 VIN = 0 to VCC Input Capacitance CIN SPI DIGITAL OUTPUT (DOUT) (Note 4) Output Leakage Current CS = VIH (Note 4) Output Capacitance IO C OUT Output Low Voltage VOL Output High Voltage VOH 2 V -0.1 V +0.1 10 -0.1 μA pF +0.1 15 μA pF VCC = +2V, I SINK = 1.5mA 0.4 VCC = +5V, I SINK = 4mA VCC = +2V, I SOURCE = -0.4mA 0.4 1.8 VCC = +5V, I SOURCE = -1mA 4.5 V V Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock AC ELECTRICAL CHARACTERISTICS (V CC = +2.0V to +5.5V, T A = -40°C to +85°C. Typical values are at V CC = +3.3V, T A = +25°C, unless otherwise noted.) (Figure 5, Notes 1, 5) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SPI SERIAL TIMING Input Rise Time Input Fall Time trIN t fIN Output Rise Time trOUT Output Fall Time t fOUT DIN, SCLK, CS 5 ns DIN, SCLK, CS 5 ns DOUT, CLOAD = 100pF 10 ns 10 ns DOUT, CLOAD = 100pF VCC = +2V 1000 VCC = +5V 238 ns SCLK Period tCP SCLK High Time tCH 100 ns SCLK Low Time tCL 100 ns SCLK Fall to DOUT Valid tDO DIN to SCLK Setup Time tDS 100 ns DIN to SCLK Hold Time tDH 20 ns SCLK Rise to CS Rise Hold Time tCSH CS High Pulse Width tCSW CS High to DOUT High Impedance tCSZ CS to SCLK Setup Time tCSS VCC = +2V, CLOAD = 100pF VCC = +5V, CLOAD = 100pF 300 100 VCC = +2V 200 VCC = +5V 50 ns ns 200 ns 100 100 ns ns Note 1: All parameters are 100% tested at TA = +25°C. Limits over temperature are guaranteed by design and characterization and not production tested. Note 2: ICC is specified with DOUT open, CS = DIN = GND, SCLK = 4MHz at VCC = +5V; SCLK = 1MHz at VCC = +2.0V. Note 3: Timekeeping current is specified with CS = VCC, SCLK = DIN = GND, DOSF = 0, EGFIL = 1. Note 4: Guaranteed by design and not 100% production tested. Note 5: All values referred to VIH(MIN) and VIL(MAX) levels. CRYSTAL CHARACTERISTICS PARAMETER SYMBOL Nominal Frequency fO Series Resistance ESR Load Capacitance CL Maxim Integrated CONDITIONS MIN TYP MAX 32.768 kHz 100 12.5 UNITS k pF 3 DS1347 Low-Current, SPI-Compatible Real-Time Clock SUPPLY CURRENT (μA) SUPPLY CURRENT (nA) TA = +25°C, IOUT = 0mA, CS = DIN = GND 100 400 DS1347 toc01 120 80 60 fSCLK = 4MHz 40 fSCLK = 1MHz TA = +25°C, CS = VCC DS1347 toc02 SUPPLY CURRENT vs. SUPPLY VOLTAGE SUPPLY CURRENT vs. SUPPLY VOLTAGE EGFIL = 1, DOSF = 0 350 300 EGFIL = 0, DOSF = 0 250 EGFIL = 0, DOSF = 1 20 200 0 2 3 4 2 6 5 3 4 5 6 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE SUPPLY CURRENT (nA) CS = VCC, EGFIL = DOSF = 0 DS1347 toc03 500 +85°C 400 +70°C +25°C 300 0°C -40°C 200 2 3 4 5 6 SUPPLY VOLTAGE (V) 4 Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Pin Configuration TOP VIEW + SCLK 1 DOUT 2 8 X1 7 X2 6 VCC 5 CS DS1347 DIN 3 GND 4 EP TDFN Pin Description PIN NAME FUNCTION 1 SCLK Serial-Clock Input. SCLK is used to synchronize data movement on the serial interface for either 3-wire or SPI communications. 2 DOUT Serial-Data Output. When SPI communication is enabled, the DOUT pin is the serial-data output for the SPI bus. 3 DIN Serial-Data Input. When SPI communication is enabled, the DIN pin is the serial-data input for the SPI bus. 4 GND Ground 5 CS Active-Low Chip Select. The chip-enable signal must be asserted low during a read or a write for SPI communications. 6 VCC Power-Supply Input 7 X2 8 X1 — EP Maxim Integrated Connections for Standard 32.768kHz Quartz Crystal (see the Crystal Characteristics table). Exposed Pad. Connect to GND or leave unconnected. 5 DS1347 Low-Current, SPI-Compatible Real-Time Clock Functional Diagram X1 X2 OSCILLATOR 32.768kHz 1Hz DIVIDER SECONDS MINUTES HOURS DS1347 DATE VCC GND CONTROL LOGIC MONTH DAY SCLK DIN DOUT CS YEAR INPUT SHIFT REGISTERS CONTROL ADDRESS REGISTER CENTURY ALARM CONFIG 31x 8 RAM STATUS ALARM THRESHOLDS CLOCK BURST RAM BURST ALARM OUT 6 ALARM CONTROL LOGIC Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Detailed Description The DS1347 is a real-time clock/calendar with an SPIcompatible interface and 31 x 8 bits of SRAM. It provides seconds, minutes, hours, day of the week, date of the month, month, and year information, held in seven 8-bit timekeeping registers (see the Functional Diagram ). An on-chip 32.768kHz oscillator circuit requires only a single external crystal to operate. Table 1 shows the device’s register addresses and definitions. Time and calendar data are stored in the registers in binary-coded decimal (BCD) format. A polled alarm function is included for scheduled timing of userdefined times or intervals. Table 1. Register Map ADDRESS BIT 7 FUNCTION RANGE 01h 0 BIT 6 10 SECONDS BIT 5 BIT 4 SECONDS Seconds 00–59 03h ALM OUT 10 MINUTES MINUTES Minutes 00–59 05h 12/24 HOUR Hours 1–12+AM/PM 00–23 AM/PM 0 BIT 3 10 HR 20 HR 07h 0 0 09h 0 0 0 10 MO 0Bh 0 0 0 0 0 WP 0 0 0 0 0Dh 0Fh BIT 2 10 DATE BIT 0 DATE Date 01–31 MONTH Month 01–12 Day 1–7 DAY 10 YEAR 13h BIT 1 YEAR 1000 YEAR 0 0 ID 100 YEAR 15h 0 YEAR DAY MONTH DATE HOUR 17h EOSC DOSF EGFIL 0 0 OSF MINUTE SECOND 1 1 Year 00–99 Control 00h or 81h Century 00–99 Alarm Configuration 00h–7Fh Status 03h–E7h 19h 0 10 SECONDS SECONDS Alarm Seconds 00–59 1Bh 0 10 MINUTES MINUTES Alarm Minutes 00–59 1Dh 12/24 HOURS Alarm Hours 1–12 + AM/PM 00–23 0 1Fh 0 0 21h 0 0 23h 0 0 25h AM/PM 20 HR 10 HR 10 DATE 0 10 MO 0 0 Alarm Date 1–31 Alarm Month 1–12 0 DAY 10 YEAR 3Fh DATE MONTH YEAR See the Data Input (Burst Write) section. Alarm Day 1–7 Alarm Year 00–99 Clock Burst — 41h X X X X X X X X RAM 0 00h–FFh 43h X X X X X X X X RAM 1 00h–FFh 45h X X X X X X X X RAM 2 00h–FFh 47h X X X X X X X X RAM 3 00h–FFh 49h X X X X X X X X RAM 4 00h–FFh 4Bh X X X X X X X X RAM 5 00h–FFh 4Dh X X X X X X X X RAM 6 00h–FFh 4Fh X X X X X X X X RAM 7 00h–FFh 51h X X X X X X X X RAM 8 00h–FFh 53h X X X X X X X X RAM 9 00h–FFh 55h X X X X X X X X RAM 10 00h–FFh Maxim Integrated 7 DS1347 Low-Current, SPI-Compatible Real-Time Clock Table 1. Register Map (continued) ADDRESS BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 FUNCTION RANGE 57h X X X X X X X X RAM 11 00h–FFh 59h X X X X X X X X RAM 12 00h–FFh 5Bh X X X X X X X X RAM 13 00h–FFh 5Dh X X X X X X X X RAM 14 00h–FFh 5Fh X X X X X X X X RAM 15 00h–FFh 61h X X X X X X X X RAM 16 00h–FFh 63h X X X X X X X X RAM 17 00h–FFh 65h X X X X X X X X RAM 18 00h–FFh 67h X X X X X X X X RAM 19 00h–FFh 69h X X X X X X X X RAM 20 00h–FFh 6Bh X X X X X X X X RAM 21 00h–FFh 6Dh X X X X X X X X RAM 22 00h–FFh 6Fh X X X X X X X X RAM 23 00h–FFh 71h X X X X X X X X RAM 24 00h–FFh 73h X X X X X X X X RAM 25 00h–FFh 75h X X X X X X X X RAM 26 00h–FFh 77h X X X X X X X X RAM 27 00h–FFh 79h X X X X X X X X RAM 28 00h–FFh 7Bh X X X X X X X X RAM 29 00h–FFh 7Dh X X X X X X X X RAM 30 00h–FFh RAM Burst — 7Fh See the Data Input (Burst Write) section. 0 = Reads as logic 0, 1 = Reads as logic 1, X = Don’t care. Command and Control Address/Command Byte Each data transfer into or out of the device is initiated by an address/command byte. The address/command byte specifies which registers are to be accessed, and if the access is a read or a write. Table 1 shows the address/command bytes and their associated registers, and lists the hex codes for all read and write operations. The address/command bytes are input MSB (bit 7) first. Bit 7 specifies a write (logic 0) or read (logic 1). Bit 6 specifies register data (logic 0) or RAM data (logic 1). Bits 5–1 specify the designated register to be written or read. The LSB (bit 0) must be logic 1. If the LSB is a zero, writes to the device are disabled. Clock Burst Mode Sending the clock burst address/command (3Fh) specifies burst-mode operation. In this mode, multiple bytes are read or written after a single address/command. 8 The first seven clock/calendar registers (Seconds, Minutes, Hours, Date, Month, Day, and Year) and the Control register are consecutively read or written, starting with the MSB of the Seconds register. When writing to the clock registers in burst mode, all seven clock/calendar registers and the Control register must be written in order for the data to be transferred. See the Example: Setting the Clock with a Burst Write section. RAM Burst Mode Sending the RAM burst address/command (7Fh) specifies burst-mode operation. In this mode, the 31 RAM locations can be consecutively read or written, starting at 41h. When writing to RAM in burst mode, it is not necessary to write all 31 bytes for the data to transfer; each complete byte written is transferred to RAM. When reading from RAM, data is output until all 31 bytes have been read, or until CS is driven high. Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Setting the Clock Writing to the Timekeeping Registers The time and date are set by writing to the timekeeping registers (Seconds, Minutes, Hours, Date, Month, Day, Year, and Century). During a write operation, an input buffer accepts the new time data while the timekeeping registers continue to increment normally, based on the crystal counter. The buffer also keeps the timekeeping registers from changing as the result of an incomplete write operation, and collision-detection circuitry ensures that a time write does not occur coincident with a Seconds register increment. The updated time is loaded into the timekeeping registers after the rising edge of CS, at the end of the SPI write operation. An incomplete write operation aborts the update procedure, and the contents of the input buffer are discarded. The timekeeping registers reflect the new time beginning with the first Seconds register increment after the rising edge of CS. Although both single writes and burst writes are possible, the best way to write to the timekeeping registers is with a burst write. With a burst write, the main timekeeping registers (Seconds, Minutes, Hours, Date, Month, Day, Year) and the Control register are written sequentially following the address/command byte. They must be written as a group of eight registers, with 8 bits each, for proper execution of the burst write function. All seven timekeeping registers are simultaneously loaded into the clock counters by the rising edge of CS, at the end of the SPI write operation. If single write operations are used to enter data into the timekeeping registers, error checking is required. If not writing to the Seconds register, begin by reading the Seconds register and save it as initial-seconds. Then write to the required timekeeping registers, and finally read the Seconds register again (final-seconds). Check to see that final-seconds is equal to initial-seconds. If not, repeat the write process. If writing to the Seconds register, update the Seconds register first, and then read it back and store its value (initial-seconds). Update the remaining timekeeping registers and then read the Seconds register again (final-seconds). Check to see that final-seconds is equal to initial-seconds. If not, repeat the write process. Maxim Integrated AM/PM and 12Hr/24Hr Mode Bit 7 of the Hours register selects 12hr or 24hr mode. When high, 12hr mode is selected. In 12hr mode, bit 5 is the AM/PM bit, logic-high for PM. In 24hr mode, bit 5 is the 20hr bit, logic-high for hours 20 through 23. Write-Protect Bit Bit 7 of the Control register is the write-protect bit. When high, the write-protect bit prevents write operations to all registers except itself. After initial settings are written to the timekeeping registers, set the writeprotect bit to logic 1 to prevent erroneous data from entering the registers during power glitches or interrupted serial transfers. The lower 7 bits (bits 0–6) are unusable, and always read zero. Any data written to bits 0–6 are ignored. Bit 7 must be set to zero before a single write to the clock, before a write to RAM, or during a burst write to the clock. Example: Setting the Clock with a Burst Write To set the clock to 10:11:31PM, Thursday July 4th, 2002, with a burst write operation, write 3Fh as the address/command byte, followed by 8 bytes, 31h, 11h, B0h, 04h, 07h, 05h, 02h, and 00h (Figure 2). 3Fh is the clock burst write address/command. The first data byte, 31h, sets the Seconds register to 31. The second data byte, 11h, sets the Minutes register to 11. The third data byte, B0h, sets the Hours register to 12hr mode, and 10PM. The fourth data byte, 04h, sets the Date register (day of the month) to the 4th. The fifth data byte, 07h, sets the Month register to July. The sixth data byte, 05h, sets the Day register (day of the week) to Thursday. The seventh data byte, 02h, sets the Year register to 02. The eighth data byte, 00h, clears the write-protect bit of the Control register to allow writing to the device. The Century register is not accessed with a burst write and therefore must be written to separately to set the century to 20. Note the Century register corresponds to the thousand and hundred digits of the current year and defaults to 19. 9 DS1347 Low-Current, SPI-Compatible Real-Time Clock Reading the Clock Reading the Timekeeping Registers The main timekeeping registers (Seconds, Minutes, Hours, Date, Month, Day, Year) can be read with either single reads or a burst read. In the device, a latch buffers each clock counter’s data. Clock counter data is latched by the SPI read command (on the falling edge of SCLK, after the address/command byte has been sent by the master to read a timekeeping register). Collision-detection circuitry ensures that this does not happen coincident with a Seconds counter increment to ensure accurate time data is read. The clock counters continue to count and keep accurate time during the read operation. The simplest way to read the timekeeping registers is to use a burst read. In a burst read, the main timekeeping registers (Seconds, Minutes, Hours, Date, Month, Day, Year), and the Control register are read sequentially, in the order listed with the Seconds register first. They are read out as a group of eight registers, with 8 bits each. All timekeeping registers (except Century) are latched upon the receipt of the burst read command. The worst-case error between the “actual” time and the “read” time is 1s for a normal data transfer. The timekeeping registers can also be read using single reads. If single reads are used, it is necessary to do some error checking on the receiving end, because it is possible that the clock counters could change during the read operations, and report inaccurate time data. The potential for error is when the Seconds register increments before all the registers are read. For example, suppose a carry of 13:59:59 to 14:00:00 occurs during single read operations. The net data read could be 14:59:59, which is erroneous. To prevent errors from occurring with single read operations, read the Seconds register first (initial-seconds) and store this value for future comparison. After the remaining timekeeping registers have been read, reread the Seconds register (final-seconds). Check that the final-seconds value equals the initial-seconds value. If not, repeat the entire single read process. Using single reads at a 100kHz serial speed, it takes under 2.5ms to read all seven of the timekeeping registers, including two reads of the Seconds register. 10 Example: Reading the Clock with a Burst Read To read the time with a burst read, send BFh as the Address/Command byte. Then clock out 8 bytes, Seconds, Minutes, Hours, Date of the month, Month, Day of the week, Year, and finally the Control byte. All data is output MSB first. Decode the required information based on the register definitions listed in Table 1. Using the Alarm A polled alarm function is available by reading the ALM OUT bit. The ALM OUT bit is D7 of the Minutes timekeeping register. A logic 1 in ALM OUT indicates the Alarm function is triggered. There are eight registers associated with the alarm function—seven programmable alarm threshold registers and one programmable Alarm Configuration register. The Alarm Configuration register determines which alarm threshold registers are compared to the timekeeping registers, and the ALM OUT bit sets if the compared registers are equal. Table 1 shows the function of each bit of the Alarm Configuration register. Placing a logic 1 in any given bit of the Alarm Configuration register enables the respective alarm function. For example, if the Alarm Configuration register is set to 0000 0011, ALM OUT is set when both the minutes and seconds indicated in the alarm threshold registers match the respective timekeeping registers. Once set, ALM OUT stays high until it is cleared by reading or writing to the Alarm Configuration register, or by reading or writing to any of the alarm threshold registers. The Alarm Configuration register is located at address 15h, and is initialized to 00h on the first application of power. Using the On-Board RAM The static RAM is 31 x 8 bits addressed consecutively in the RAM Address/Command space. Table 1 details the specific hex address/commands for reads and writes to each of the 31 locations of RAM. The contents of the RAM are static and remain valid for VCC down to 2V. All RAM data is lost if power is cycled. The writeprotect bit (WP in the Control register), when high, disallows any writes to RAM. The RAM’s power-on state is undefined. Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Control Register (0Fh) BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 WP 0 0 0 0 0 0 ID 0 0 0 0 0 0 0 0 BIT 7 WP: Write-Protect RAM. If the WP bit is logic one, writing to the 31 bytes of RAM is inhibited. This bit is cleared (0) when power is first applied. BIT 0 ID: Device Identification Bit. The content of this bit does not alter the component functionality. This bit is cleared (0) when power is first applied. Alarm Configuration Register (15h) BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 0 YEAR DAY MONTH DATE HOUR MINUTE SECOND 0 0 0 0 0 0 0 0 Status Register (17h) BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 EOSC DOSF EGFIL 0 0 OSF 0 0 0 0 0 0 0 1 1 1 BIT 7 EOSC: Enable Oscillator. When the EOSC bit is logic 0, the oscillator is enabled. When this bit is logic 1, the oscillator is disabled. This bit is cleared (0) when power is first applied. BIT 6 DOSF: Disable Oscillator Stop Flag. When the DOSF bit is set to 1, sensing of the oscillator conditions that would set the OSF bit is disabled. OSF remains at 0 regardless of what happens to the oscillator. This bit is cleared (0) on the initial application of power. BIT 5 EGFIL: Enable Glitch Filter. When the EGFIL bit is 1, the 5μs glitch filter at the output of crystal oscillator is enabled. The glitch filter is disabled when this bit is 0. This bit is cleared (0) on the initial application of power. BIT 2 OSF: Oscillator Stop Flag. If the OSF bit is 1, the oscillator either has stopped or was stopped for some period and could be used to judge the validity of the clock and calendar data. This bit is edge triggered and is set to 1 when the internal circuitry senses the oscillator has transitioned from a normal run state to a stop condition. This bit remains at logic 1 until written to logic 0. Attempting to write OSF to 1 leaves the value unchanged. The following are examples of conditions that can cause the OSF bit to be set: 1) The first time power is applied. 2) The voltage present on VCC is insufficient to support oscillation. 3) The EOSC bit is set to logic 1. 4) External influences on the crystal (i.e., noise, leakage, etc.). Alarm Seconds Register (19h) BIT 7 BIT 6 0 0 Maxim Integrated BIT 5 BIT 4 BIT 3 BIT 2 10 SECONDS 1 1 BIT 1 BIT 0 1 1 SECONDS 1 1 1 11 DS1347 Low-Current, SPI-Compatible Real-Time Clock Alarm Minutes Register (1Bh) BIT 7 BIT 6 0 0 BIT 5 BIT 4 BIT 3 BIT 2 10 MINUTES 1 1 BIT 1 BIT 0 1 1 MINUTES 1 1 1 Alarm Hours Register (1Dh) BIT 7 BIT 6 12/24 0 1 0 BIT 5 BIT 4 AM/PM 20 HR 1 BIT 3 BIT 2 10 HR 1 BIT 1 BIT 0 1 1 HOURS 1 1 Alarm Date Register (1Fh) BIT 7 BIT 6 0 0 0 0 BIT 5 BIT 4 BIT 3 BIT 2 10 DATE 1 BIT 1 BIT 0 1 1 DATE 1 1 1 Alarm Month Register (21h) BIT 7 BIT 6 BIT 5 BIT 4 0 0 0 10 MO 0 0 0 1 BIT 3 BIT 2 BIT 1 BIT 0 1 1 MONTH 1 1 Alarm Day Register (23h) BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 0 0 0 0 0 0 0 0 0 0 BIT 2 BIT 1 BIT 0 DAY 1 1 1 Alarm Year Register (25h) BIT 7 BIT 6 1 1 BIT 5 BIT 4 BIT 3 BIT 2 1 1 1 1 10 YEAR BIT 0 1 1 YEAR SPI-Compatible Serial Interface Interface the device with a microcontroller using a serial, 4-wire, SPI interface. SPI is a synchronous bus for address and data transfer, and is used with Motorola or other microcontrollers that have an SPI port. Four connections are required for the interface: DOUT (serialdata out); DIN (serial-data in); SCLK (serial clock); and CS (chip select). In an SPI application, the device acts 12 BIT 1 as a slave device and the microcontroller acts as the master. CS is asserted low by the microcontroller to initiate a transfer, and deasserted high to terminate a transfer. DIN transfers input data from the microcontroller to the device. DOUT transfers output data from the device to the microcontroller. A shift clock, SCLK, is used to synchronize data movement between the microcontroller and the device. SCLK, which is generated by the Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock microcontroller, is active only during address and data transfer to any device on the SPI bus. The inactive clock polarity is usually programmable on the microcontroller side of the SPI interface. In the device, input data is latched on the positive edge, and output data is shifted out on the negative edge. There is one clock cycle for each bit transferred. Address and data bits are transferred in groups of eight. The SPI protocol allows for one of four combinations of serial clock phase and polarity from the microcontroller, through a 2-bit selection in its SPI Control register. The clock polarity is specified by the CPOL Control bit, which selects active-high or active-low clock, and has no significant effect on the transfer format. The clock phase control bit, CPHA, selects one of two different transfer formats. The clock phase and polarity must be identical for the master and the slave. For the device, set the control bits to CPHA = 1 and CPOL = 1. This configures the system for data out to be launched on the negative edge of SCLK and data in to be sampled on the positive edge. With CPHA equal to 1, CS can remain low between successive data byte transfers, allowing burst-mode data transfers to occur. Address and data bytes are shifted MSB first into DIN of the device, and out of DOUT. Data is shifted out at the negative edge of SCLK, and shifted in or sampled at the positive edge of SCLK. Any transfer requires an address/command byte followed by one or more bytes of data. Data is transferred out of DOUT for a read operation, and into DIN for a write operation. DOUT transmits data only after an address/command byte specifies a read operation; otherwise, it is high impedance. Data transfer write timing is shown in Figure 1. Data transfer read timing is shown in Figure 2. Detailed read and write timing is shown in Figure 3. CS SCLK DIN R/W A6 A5 A4 A3 A2 A1 1 D7 D6 D5 ADDRESS/COMMAND BYTE D4 D3 D2 D1 D0 DATA BYTE HIGH IMPEDANCE; NO ACTIVITY ON DOUT LINE DURING WRITES. DOUT Figure 1a. Single Write CS SCLK DIN R/W A6 1 1 1 1 1 1 D7 D6 ADDRESS/COMMAND BYTE* DOUT D5 D4 D3 D2 DATA BYTE 1 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE N HIGH IMPEDANCE; NO ACTIVITY ON DOUT LINE DURING WRITES. *ONLY ONE ADDRESS/COMMAND BYTE IS REQUIRED PER BURST TRANSACTION. Figure 2b. Burst Write Maxim Integrated 13 DS1347 Low-Current, SPI-Compatible Real-Time Clock CS SCLK DIN R/W A6 A5 A4 A3 A2 A1 1 ADDRESS/COMMAND BYTE HIGH IMPEDANCE DOUT D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE Figure 2a. Single Read CS SCLK DIN R/W A6 1 1 1 1 1 1 ADDRESS/COMMAND BYTE* HIGH IMPEDANCE DOUT D7 D6 *ONLY ONE ADDRESS/COMMAND BYTE IS REQUIRED PER BURST TRANSACTION. D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 DATA BYTE N DATA BYTE 1 Figure 2b. Burst Read tCSH CS tCSS tCH tCL tCP tCSW SCLK tDH tDS DIN R/W A6 A5 1 tCSZ D7 DOUT D0 tDO Figure 3. SPI Bus Timing Diagram 14 Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Chip Select CS serves two functions. First, CS turns on the control logic that allows access to the Shift register for address/command and data transfer. Second, CS provides a method of terminating either single-byte or multiple-byte data transfers. All data transfers are initiated by driving CS low. If CS is high, then DOUT is high impedance. Serial Clock A clock cycle on SCLK is a rising edge followed by a falling edge. For data input, data must be valid at DIN before the rising edge of the clock. For data outputs, bits are valid on DOUT after the falling edge of the clock. Data Input (Single-Byte Write) Following the eight SCLK cycles that input a single-byte write address/command, data bits are input on the rising edges of the next eight SCLK cycles. Additional SCLK cycles are ignored. Input data MSB first. Data Input (Burst Write) Following the eight SCLK cycles that input a burst-write address/command, data bits are input on the rising edges of the following SCLK cycles. The number of clock cycles depends on whether the timekeeping registers or RAM are being written. A clock burst write requires 1 address/command byte, 7 timekeeping data bytes, and 1 control register byte. A burst write to RAM can be terminated after any complete data byte by driving CS high. Input data MSB first (Figure 1). Data Output (Single-Byte Read and Burst Read) A read from the device is initiated by an address/command Write from the microcontroller (master) to the device (slave). The address/command write portion of the data transfer is clocked into the device on rising clock edges. Following the eighth falling clock edge of SCLK, after tDO (Figure 2) data begins to be output on DOUT of the device. Data bytes are output MSB first. Additional SCLK cycles transmit additional data bits, as long as CS remains low. This permits continuous burstmode read capability. Maxim Integrated Applications Information Oscillator Start Time The device’s oscillator typically takes less than 2s to begin oscillating. To ensure the oscillator is operating correctly, the software should validate proper timekeeping. This is accomplished by reading the Seconds register. Any reading of 1s or more from the POR value of zero seconds is a validation of proper startup. Power-On Reset The device contains an integral POR circuit that ensures all registers are reset to a known state on power-up. Upon a POR, the time and date are set to 00:00:00 01/01/1970 (hh:mm:ss DD/MM/YYYY) and the day register is set to 01. Once VCC rises, the POR circuit releases the registers for normal operation. Power-Supply Considerations For most applications, a 0.1µF capacitor from VCC to GND provides adequate bypassing for the device. A series resistor can be added to the supply line for operation in extremely harsh or noisy environments. PCB Considerations The device uses a very low-current oscillator to minimize supply current. This causes the oscillator pins, X1 and X2, to be relatively high impedance. Exercise care to prevent unwanted noise pickup. Connect the 32.768kHz crystal directly across X1 and X2 of the device. To eliminate unwanted noise pickup, design the PCB using these guidelines (Figure 4): 1) Place the crystal as close to X1 and X2 as possible and keep the trace lengths short. 2) Place a guard ring around the crystal, X1 and X2 traces (where applicable), and connect the guard ring to GND; keep all signal traces away from beneath the crystal, X1, and X2. 3) Finally, an additional local ground plane can be added under the crystal on an adjacent PCB layer. The plane should be isolated from the regular PCB ground plane, and connected to ground at the IC ground pin. 4) Restrict the plane to be no larger than the perimeter of the guard ring. Do not allow this ground plane to contribute significant capacitance between X1 and X2. 15 DS1347 Low-Current, SPI-Compatible Real-Time Clock GROUND PLANE VIA CONNECTION * VCC PLANE VIA CONNECTION GUARD RING GROUND PLANE VIA CONNECTION * 0.1µF SM CAP * ** ** * DS1347 * * * * * ** 2 LOCAL GROUND PLANE ** LAYER CONNECT ONLY TO PIN 4 SM WATCH CRYSTAL GROUND PLANE VIA * ** * GROUND PLANE VIA CONNECTION *LAYER 1 TRACE Figure 4. Crystal PCB Layout Chip Information PROCESS: CMOS 16 Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 8 TDFN-EP T833+2 21-0137 90-0059 Maxim Integrated DS1347 Low-Current, SPI-Compatible Real-Time Clock Revision History PAGES CHANGED REVISION NUMBER REVISION DATE 0 8/11 Initial release — 1 1/12 Removed all references to the DS1346 All 2 2/12 Removed the external oscillator text from the X1 pin description in the Pin Description table 5 3 1/13 Moved Crystal Characteristics table below notes; added POR content for clock/calendar registers. 3, 15 DESCRIPTION Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 © 2013 Maxim Integrated Products, Inc. 17 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.