REVISION G DO NOT SCALE FROM THIS PRINT ANY REV MADE TO THIS PRINT MUST HAVE AN UPDATED MKT PRINT NOTES: 1. BANK 1 IS DIFFERENTIAL PAIR, BANK 2 & 3 ARE SINGLE ENDED. 2. C REPRESENTS A CRITICAL DIMENSION. 3. MINIMUM GROUND PLANE & CONTACT RETENTION: 8 OZ. 4. MAXIMUM BURR ALLOWANCE: .0015. 5. MAXIMUM HEIGHT VARIANCE OF .002 APPLIES TO SIGNAL OR GROUNDS INDEPENDENT OF THE GROUND OR SIGNAL PINS RESPECTIVELY. 6. GROUND PLANE PRESS HEIGHT MUST BE .003 LESS THAN THE MAX HEIGHT OR .002 GREATER THAN THE MINIMUM HEIGHT OF SIGNAL PIN. 7. PARTS TO BE PACKAGED IN TRAYS. .1107 .105 2.368 .551 .571(2 PLCS) .0197(TYP) .028(9 PLCS) .0895(TYP) .040 .068 (TYP) .017 (TYP) .236 .011(TYP) .153(2 PLCS) .250(TYP) .1925(TYP) .100(TYP) (2 PLCS PER BANK) .217 .185(TYP) (2 PLCS PER BANK) FOOT PRINT .78 REF 02 2.413 ((90 POS / 30 x .7875) + .050) .571 (29 EQ SPACES @ .0197) .150 REF .245 REF 01 DP BANK .036 REF .285 REF 2 .006 REF .626 REF 1 "A" .038 REF C1 .120 REF .725 REF .035 REF .006 "A" 3 +.003 .128 - .001 .070 REF .038 REF .007 .2950 REF 2.368 REF ((90 POS/30) x .7875) + .005 SECTION "A"-"A" SCALE 2 : 1 UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ITEM NO. PART NUMBER QUANTITY MATERIAL 1 QSH-30-01-D-03-A 1.0000 VECTRA E130i, COLOR: BLACK 2 C-126-21-F 160.00 PHOS BRONZE, 510 SPRING TEMPER 3 T-1G2-01-F 3.0000 PHOS BRONZE, 510 HALF HARD TEMPER 4 TRAY-QXX008-PR-01-AP-T-A 1.0000 ANTI-STATIC BLACK HIPS ANGLES .XX: .01[.3] .XXX: .005[.13] .XXXX: .0020[.051] 2 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING GROUND PLANE & CONTACT PLATING: CONTACT AREA: .000003 GOLD OVER .000050 NICKEL SHEET SCALE: 3:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: .5MM DBL HS/DP SOCKET ASSEMBLY DWG. NO. c:\enterprisevault\DWG\MISC\MKTG\ASP-122953-01-MKT.SLDDRW BY: RRC ASP-122953-01 1/13/06 SHEET 1 OF 1