REVISION AA QSH-XXX-01-X-D-XXX No OF POSITIONS -030, -060, -090, *-120,* -150 (PER ROW) *SEE NOTE 11 LEAD STYLE -01: .1280[3.25] PLATING SPECIFICATION -F: FLASH SELECTIVE GOLD WITH MATTE TIN TAILS (USE C-126-21-F, T-1G2-01-F) (SEE NOTE 8 & 10) -L: LIGHT SELECTIVE GOLD WITH MATTE TIN TAILS (USE C-126-21-L, T-1G2-01-L) (SEE NOTE 10) -H: HEAVY GOLD (USE C-126-21-H, T-1G2-01-G) (SEE NOTE 10) -C: ELECTRO-POLISHED SELECTIVE (USE C-126-21-C, T-1G2-01-L) (SEE NOTE 10) ROW SPECIFICATION -D: DOUBLE (USE QSH-30-01-D-XX) FIG. 1 -LC: LOCKING CLIP OPTION SHOWN C3 DO NOT SCALE FROM THIS PRINT ((No OF POSITIONS / 30) x .7875[20.003] + "A") .7875 20.003 (TYP) 02 29 EQ. SPACES x .01965[.500] .245 6.22 REF 01 .626 15.89 REF .006 0.15 REF .036 0.92 REF .0550 1.397 "A" .150 3.81 REF No OF BANKS .285 7.24 REF QSH-30-01-D-XX C-126-21-X .010 0.25 REF .725 18.42 REF C1 .007 0.18 REF .070 1.77 REF T-1G2-01-X SECTION "A"-"A" ((No OF POSITIONS / 30) x .7875[20.003]) + .005[.13] UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS .XX: .01[.3] .XXX: .005[.13] .XXXX: .0020[.051] MATERIAL: ANGLES 2 +0.076 SEE TABLE 1 LC-08-TM-01 .0375 0.953 REF +.0030 .1280 - .0010 3.251 - 0.025 (SEE NOTE 6 & 7) C2 .120 3.05 REF "A" OPTION -A: ALIGNMENT PINS (USE QSH-30-01-D-XX-A, SEE FIG. 2) -LC: LOCKING CLIPS (USE LC-08-TM-01) -GP: GUIDE POSTS (USE QSH-30-01-D-XX-X-GP) (SEE FIG. 4, SHEET 3) (TAPE & REEL FOR -GP, 60 POS MAX) -K: POLYIMIDE FILM PAD (USE K-DOT-.325-.450-.005, SEE FIG. 3) -TR: TAPE & REEL (90 POS MAX) -FL: FRICTION LOCKS (SEE FIG. 5, SHEET 3) (NOT AVAILABLE WITH -GP) -RT1: RETENTION (MUST USE -A OPTION) (USE QSH-30-01-D-XX-A-RT1 & SUB-SC-05-01-FF) (SEE FIG. 6, SHEET 3) (NOT AVAILABLE WITH -LC, -GP, OR -FL) (NOT AVAILABLE WITH -120 & -150 POS) .2950 7.493 REF NOTES: 1. C REPRESENTS A CRITICAL DIMENSION. 2. NOTE DELETED. 3. CONTACT RETENTION: 8 OZ. MINIMUM. 4. GROUND PLANE RETENTION: 8 OZ. MINIMUM. 5. BURR ALLOWANCE: .0015[.038] MAX. 6. MAX VARIANCE: .002[.05]. 7. DIMENSION APPLIES TO CONTACT & GROUND PLANE. 8. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING, -G PLATED GROUND PLANE CAN BE SUBSTITUTED FOR -F PLATED GROUND PLANE. 9. SUB-SC-05-01-XX RETENTION TO BE 1.0 LBF IN BODY. 10. MAY SUB C-126-01 FOR C-126-21. 11. FOR NEW APPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT SAMTEC INTERCONNECT PROCESSING GROUP. PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 1.5:1 INSULATOR: BLACK LCP CONTACT & GROUND PLANE: PHOS BRONZE c:\enterprisevault\DWG\MISC\MKTG\QSH-XXX-01-X-D-XXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: .5mm DOUBLE ROW HS SOCKET ASSEMBLY DWG. NO. QSH-XXX-01-X-D-XXX BY: DEAN P 05/21/1999 SHEET 1 OF 3 REVISION AA FIG. 2 -A: ALIGNMENT PIN OPTION QSH-30-01-D-XX-A .030 0.76 REF R .035 0.89 REF ((No OF POSITIONS / 30) x .7875[20.003]) + .005[.13] REF FIG. 3 -K: POLYIMIDE FILM PAD [USE K-DOT-.325-.450-.005] "S" .020 0.51 .133 3.38 .325 8.26 "R" REF NOTE: "R" = ((No OF POSITIONS / 30) x .7875[20.003]) + .050[1.27] WITH -RT1 OPTION: "R" = ((No OF POSITIONS / 30) x .7875[20.003]) + .650[16.51] REF WITH -GP OPTION: "R" = ((No OF POSITIONS / 30) x .7875[20.003]) + .4285[10.884] REF "S" = (("R" - .325[8.26]) / 2) .020[.51] PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 2.5:1 c:\enterprisevault\DWG\MISC\MKTG\QSH-XXX-01-X-D-XXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: .5mm DOUBLE ROW HS SOCKET ASSEMBLY DWG. NO. QSH-XXX-01-X-D-XXX BY: DEAN P 05/21/1999 SHEET 2 OF 3 REVISION AA FIG. 4 FIG. 5 -GP: GUIDE POSTS (SAME AS FIG. 1, UNLESS OTHERWISE STATED) -FL: FRICTION LOCKS (NOT AVAILABLE WITH -GP OPTION) (SAME AS FIG. 1, UNLESS OTHERWISE STATED) ((No OF POS / 30) x .7875[20.003]) + .4285[10.884] REF .102 2.58 REF ((No OF POS / 30) x .7875[20.003]) + .225[5.72] REF .221 5.61 REF "B" "B" .080 2.03 REF (TYP) QSH-30-01-D-XX-FL .140 3.56 THRU REF 'A' QSH-30-01-D-XX-GP .026 0.66 REF (TYP) DETAIL 'A' SCALE 8 : 1 SECTION "B"-"B" FIG. 6 -RT1: RETENTION OPTION (MUST USE -A OPTION) (NOT AVAILABLE WITH -LC, -GP, OR -FL OPTIONS) (NOT AVAILABLE WITH -120 & -150 POS) (SAME AS FIG. 1, UNLESS OTHERWISE STATED) ((No OF BANKS) x .7875[20.003]) + .650[16.51] REF C4 ((No OF BANKS) x .7875[20.003]) + .341[8.66] .003 .004 .045 1.14 REF "D" "D" C6 .150 3.81 (SEE NOTE 9) QSH-30-01-D-XX-A-RT1 'E' DETAIL 'E' SCALE 3 : 1 PROPRIETARY NOTE SUB-SC-05-01-FF (2 PLCS) C5 .148 3.76 REF ((No OF BANKS) x .7875[20.003]) + .341[8.66] .003 .004 THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SECTION "D"-"D" SCALE 1.5 : 1 SHEET SCALE: 1.5:1 c:\enterprisevault\DWG\MISC\MKTG\QSH-XXX-01-X-D-XXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: [email protected] code: 55322 DESCRIPTION: .5mm DOUBLE ROW HS SOCKET ASSEMBLY DWG. NO. QSH-XXX-01-X-D-XXX BY: DEAN P 05/21/1999 SHEET 3 OF 3