CAV25080, CAV25160 8-Kb and 16-Kb SPI Serial CMOS EEPROM Description The CAV25080/25160 are 8−Kb/16−Kb Serial CMOS EEPROM devices internally organized as 1024x8/2048x8 bits. They feature a 32−byte page write buffer and support the Serial Peripheral Interface (SPI) protocol. The device is enabled through a Chip Select (CS) input. In addition, the required bus signals are a clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input may be used to pause any serial communication with the CAV25080/25160 device. These devices feature software and hardware write protection, including partial as well as full array protection. Features • • • • • • • • • • • • • • Automotive Temperature Grade 1 (−40°C to +125°C) 10 MHz SPI Compatible 2.5 V to 5.5 V Supply Voltage Range SPI Modes (0,0) & (1,1) 32−byte Page Write Buffer Self−timed Write Cycle Hardware and Software Protection Block Write Protection − Protect 1/4, 1/2 or Entire EEPROM Array Low Power CMOS Technology 1,000,000 Program/Erase Cycles 100 Year Data Retention Industrial and Extended Temperature Range 8−lead SOIC and TSSOP Packages These Devices are Pb−Free, Halogen Free/BFR Free, and RoHS Compliant CAV25080 CAV25160 TSSOP−8 Y SUFFIX CASE 948AL PIN CONFIGURATION CS 1 VCC SO HOLD WP SCK VSS SI SOIC (V), TSSOP (Y) PIN FUNCTION Pin Name Function CS Chip Select SO Serial Data Output WP Write Protect VSS Ground Serial Data Input SCK HOLD SI WP SOIC−8 V SUFFIX CASE 751BD SI VCC CS http://onsemi.com VCC Serial Clock Hold Transmission Input Power Supply SO ORDERING INFORMATION HOLD See detailed ordering and shipping information in the package dimensions section on page 13 of this data sheet. SCK VSS Figure 1. Functional Symbol © Semiconductor Components Industries, LLC, 2011 November, 2011 − Rev. 0 1 Publication Order Number: CAV25080/D CAV25080, CAV25160 MARKING DIAGRAMS 25xx0D AYMXXX G SxxD AYMXXX G (SOIC−8) (TSSOP−8) S08D = CAV25080 S16D = CAV25160 A = Assembly Location Y = Production Year (Last Digit) M = Production Month (1−9, O, N, D) XXX = Last Three Digits of XXX = Assembly Lot Number G = Pb−Free Package 25080D = CAV25080 25160D = CAV25160 A = Assembly Location Y = Production Year (Last Digit) M = Production Month (1−9, O, N, D) XXX = Last Three Digits of XXX = Assembly Lot Number G = Pb−Free Package Table 1. ABSOLUTE MAXIMUM RATINGS Ratings Units Operating Temperature Parameters −45 to +130 °C Storage Temperature −65 to +150 °C Voltage on any Pin with Respect to Ground (Note 1) −0.5 to +6.5 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns. Table 2. RELIABILITY CHARACTERISTICS (Note 2) Symbol Parameter NEND (Note 3) TDR Endurance Data Retention Min Units 1,000,000 Program / Erase Cycles 100 Years 2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100 and JEDEC test methods. 3. Page Mode, VCC = 5 V, 25°C. Table 3. D.C. OPERATING CHARACTERISTICS (VCC = 2.5 V to 5.5 V, TA = −40°C to +125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min Max Units ICCR Supply Current (Read Mode) Read, VCC = 5.5 V, 5 MHz, SO open 2 mA ICCW Supply Current (Write Mode) Write, VCC = 5.5 V, 5 MHz, SO open 3 mA ISB1 Standby Current VIN = GND or VCC, CS = VCC, WP = VCC, VCC = 5.5 V 2 mA ISB2 Standby Current VIN = GND or VCC, CS = VCC, WP = GND, VCC = 5.5 V 5 mA Input Leakage Current VIN = GND or VCC −2 2 mA ILO Output Leakage Current CS = VCC, VOUT = GND or VCC −1 2 mA VIL Input Low Voltage −0.5 0.3 VCC V 0.7 VCC VCC + 0.5 V 0.4 V IL VIH Input High Voltage VOL1 Output Low Voltage IOL = 3.0 mA VOH1 Output High Voltage IOH = −1.6 mA http://onsemi.com 2 VCC − 0.8 V V CAV25080, CAV25160 Table 4. PIN CAPACITANCE (TA = 25°C, f = 1.0 MHz, VCC = +5.0 V) (Note 2) Test Symbol COUT Conditions Output Capacitance (SO) CIN Input Capacitance (CS, SCK, SI, WP, HOLD) Min Typ Max Units VOUT = 0 V 8 pF VIN = 0 V 8 pF Table 5. A.C. CHARACTERISTICS (TA = −40°C to +125°C) (Note 4) VCC = 2.5 V − 5.5 V Min Max Units fSCK Clock Frequency DC 10 MHz tSU Data Setup Time 10 ns tH Data Hold Time 10 ns tWH SCK High Time 40 ns tWL SCK Low Time 40 ns tLZ Parameter Symbol HOLD to Output Low Z 25 ns tRI (Note 5) Input Rise Time 2 ms tFI (Note 5) Input Fall Time 2 ms tHD HOLD Setup Time 0 ns tCD HOLD Hold Time 10 ns tV tHO tDIS tHZ Output Valid from Clock Low 35 Output Hold Time 0 Output Disable Time HOLD to Output High Z ns ns 20 ns 25 ns tCS CS High Time 40 ns tCSS CS Setup Time 30 ns tCSH CS Hold Time 30 ns tCNS CS Inactive Setup Time 20 ns tCNH CS Inactive Hold Time 20 ns tWPS WP Setup Time 10 ns tWPH WP Hold Time 10 ns tWC (Note 6) Write Cycle Time 5 ms 4. AC Test Conditions: Input Pulse Voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 10 ns Input and output reference voltages: 0.5 VCC Output load: current source IOL max/IOH max; CL = 30 pF 5. This parameter is tested initially and after a design or process change that affects the parameter. 6. tWC is the time from the rising edge of CS after a valid write sequence to the end of the internal write cycle. Table 6. POWER−UP TIMING (Notes 5, 7) Min Max Units tPUR Power−up to Read Operation 0.1 1 ms tPUW Power−up to Write Operation 0.1 1 ms Symbol Parameter 7. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. http://onsemi.com 3 CAV25080, CAV25160 Pin Description SI: The serial data input pin accepts op−codes, addresses and data. In SPI modes (0,0) and (1,1) input data is latched on the rising edge of the SCK clock input. SO: The serial data output pin is used to transfer data out of the device. In SPI modes (0,0) and (1,1) data is shifted out on the falling edge of the SCK clock. SCK: The serial clock input pin accepts the clock provided by the host and used for synchronizing communication between host and CAV25080/160. CS: The chip select input pin is used to enable/disable the CAV25080/160. When CS is high, the SO output is tri−stated (high impedance) and the device is in Standby Mode (unless an internal write operation is in progress). Every communication session between host and CAV25080/160 must be preceded by a high to low transition and concluded with a low to high transition of the CS input. WP: The write protect input pin will allow all write operations to the device when held high. When WP pin is tied low and the WPEN bit in the Status Register (refer to Status Register description, later in this Data Sheet) is set to “1”, writing to the Status Register is disabled. HOLD: The HOLD input pin is used to pause transmission between host and CAV25080/160, without having to retransmit the entire sequence at a later time. To pause, HOLD must be taken low and to resume it must be taken back high, with the SCK input low during both transitions. When not used for pausing, the HOLD input should be tied to VCC, either directly or through a resistor. Functional Description The CAV25080/160 devices support the Serial Peripheral Interface (SPI) bus protocol, modes (0,0) and (1,1). The device contains an 8−bit instruction register. The instruction set and associated op−codes are listed in Table 7. Reading data stored in the CAV25080/160 is accomplished by simply providing the READ command and an address. Writing to the CAV25080/160, in addition to a WRITE command, address and data, also requires enabling the device for writing by first setting certain bits in a Status Register, as will be explained later. After a high to low transition on the CS input pin, the CAV25080/160 will accept any one of the six instruction op−codes listed in Table 7 and will ignore all other possible 8−bit combinations. The communication protocol follows the timing from Figure 2. Table 7. INSTRUCTION SET Instruction Opcode Operation WREN 0000 0110 Enable Write Operations WRDI 0000 0100 Disable Write Operations RDSR 0000 0101 Read Status Register WRSR 0000 0001 Write Status Register READ 0000 0011 Read Data from Memory WRITE 0000 0010 Write Data to Memory tCS CS tCSS tCNH tWH tWL tCSH tCNS SCK tSU tH tRI tFI VALID IN SI tV tV tDIS tHO SO HI−Z VALID OUT HI−Z Figure 2. Synchronous Data Timing Status Register Write Enable state and when set to 0, the device is in a Write Disable state. The BP0 and BP1 (Block Protect) bits determine which blocks are currently write protected. They are set by the user with the WRSR command and are non−volatile. The user is allowed to protect a quarter, one half or the entire memory, by setting these bits according to Table 9. The protected blocks then become read−only. The Status Register, as shown in Table 8, contains a number of status and control bits. The RDY (Ready) bit indicates whether the device is busy with a write operation. This bit is automatically set to 1 during an internal write cycle, and reset to 0 when the device is ready to accept commands. For the host, this bit is read only. The WEL (Write Enable Latch) bit is set/reset by the WREN/WRDI commands. When set to 1, the device is in a http://onsemi.com 4 CAV25080, CAV25160 Table 8. STATUS REGISTER 7 6 5 4 3 2 1 0 WPEN 0 0 0 BP1 BP0 WEL RDY Table 9. BLOCK PROTECTION BITS Status Register Bits BP1 BP0 0 0 None No Protection 0 1 25080: 0300−03FF 25160: 0600−07FF Quarter Array Protection 1 0 25080: 0200−03FF 25160: 0400−07FF Half Array Protection 1 1 25080: 0000−03FF 25160: 0000−07FF Full Array Protection Array Address Protected Protection Table 10. WRITE PROTECT CONDITIONS WPEN WP WEL Protected Blocks Unprotected Blocks Status Register 0 X 0 Protected Protected Protected 0 X 1 Protected Writable Writable 1 Low 0 Protected Protected Protected 1 Low 1 Protected Writable Protected X High 0 Protected Protected Protected X High 1 Protected Writable Writable http://onsemi.com 5 CAV25080, CAV25160 WRITE OPERATIONS The CAV25080/160 device powers up into a write disable state. The device contains a Write Enable Latch (WEL) which must be set before attempting to write to the memory array or to the status register. In addition, the address of the memory location(s) to be written must be outside the protected area, as defined by BP0 and BP1 bits from the status register. instruction to the CAV25080/160. Care must be taken to take the CS input high after the WREN instruction, as otherwise the Write Enable Latch will not be properly set. WREN timing is illustrated in Figure 3. The WREN instruction must be sent prior to any WRITE or WRSR instruction. The internal write enable latch is reset by sending the WRDI instruction as shown in Figure 4. Disabling write operations by resetting the WEL bit, will protect the device against inadvertent writes. Write Enable and Write Disable The internal Write Enable Latch and the corresponding Status Register WEL bit are set by sending the WREN CS SCK 0 SI SO 0 0 0 0 1 1 0 HIGH IMPEDANCE Dashed Line = mode (1, 1) Figure 3. WREN Timing CS SCK SI SO 0 0 0 0 0 1 0 HIGH IMPEDANCE Dashed Line = mode (1, 1) Figure 4. WRDI Timing http://onsemi.com 6 0 CAV25080, CAV25160 Byte Write Page Write Once the WEL bit is set, the user may execute a write sequence, by sending a WRITE instruction, a 16−bit address and data as shown in Figure 5. Only 10 significant address bits are used by the CAV25080 and 11 by the CAV25160. The rest are don’t care bits, as shown in Table 11. Internal programming will start after the low to high CS transition. During an internal write cycle, all commands, except for RDSR (Read Status Register) will be ignored. The RDY bit will indicate if the internal write cycle is in progress (RDY high), or the device is ready to accept commands (RDY low). After sending the first data byte to the CAV25080/160, the host may continue sending data, up to a total of 32 bytes, according to timing shown in Figure 6. After each data byte, the lower order address bits are automatically incremented, while the higher order address bits (page address) remain unchanged. If during this process the end of page is exceeded, then loading will “roll over” to the first byte in the page, thus possibly overwriting previously loaded data. Following completion of the write cycle, the CAV25080/160 is automatically returned to the write disable state. Table 11. BYTE ADDRESS Address Significant Bits Address Don’t Care Bits # Address Clock Pulse CAV25080 Device A9 − A0 A15 − A10 16 CAV25160 A10 − A0 A15 − A11 16 CS 0 1 2 3 4 5 6 7 21 8 22 23 24 25 26 27 28 29 30 31 SCK OPCODE SI 0 0 0 0 0 0 DATA IN BYTE ADDRESS* 1 0 A0 D7 D6 D5 D4 D3 D2 D1 D0 AN HIGH IMPEDANCE SO * Please check the Byte Address Table (Table 11) Dashed Line = mode (1, 1) Figure 5. Byte WRITE Timing CS 0 1 2 3 4 5 6 7 8 21 SCK 0 0 0 0 0 0 23 24−31 32−39 24+(N−1)x8−1 .. 24+(N−1)x8 24+Nx8−1 BYTE ADDRESS* OPCODE SI 22 1 0 AN DATA IN A0 Data Data Data Byte 1 Byte 2 Byte 3 HIGH IMPEDANCE SO Dashed Line = mode (1, 1) Data Byte N 7..1 0 * Please check the Byte Address Table (Table 11) Figure 6. Page WRITE Timing http://onsemi.com 7 CAV25080, CAV25160 Write Status Register Write Protection The Status Register is written by sending a WRSR instruction according to timing shown in Figure 7. Only bits 2, 3 and 7 can be written using the WRSR command. The Write Protect (WP) pin can be used to protect the Block Protect bits BP0 and BP1 against being inadvertently altered. When WP is low and the WPEN bit is set to “1”, write operations to the Status Register are inhibited. WP going low while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated, WP going low will have no effect on any write operation to the Status Register. The WP pin function is blocked when the WPEN bit is set to “0”. The WP input timing is shown in Figure 8. CS 0 1 2 3 4 5 6 7 8 9 10 11 1 7 6 5 4 12 13 14 15 2 1 0 SCK OPCODE SI 0 0 0 0 0 DATA IN 0 0 MSB HIGH IMPEDANCE SO Dashed Line = mode (1, 1) Figure 7. WRSR Timing tWPS tWPH CS SCK WP WP Dashed Line = mode (1, 1) Figure 8. WP Timing http://onsemi.com 8 3 CAV25080, CAV25160 READ OPERATIONS Read from Memory Array Read Status Register To read from memory, the host sends a READ instruction followed by a 16−bit address (see Table 11 for the number of significant address bits). After receiving the last address bit, the CAV25080/160 will respond by shifting out data on the SO pin (as shown in Figure 9). Sequentially stored data can be read out by simply continuing to run the clock. The internal address pointer is automatically incremented to the next higher address as data is shifted out. After reaching the highest memory address, the address counter “rolls over” to the lowest memory address, and the read cycle can be continued indefinitely. The read operation is terminated by taking CS high. To read the status register, the host simply sends a RDSR command. After receiving the last bit of the command, the CAV25080/160 will shift out the contents of the status register on the SO pin (Figure 10). The status register may be read at any time, including during an internal write cycle. While the internal write cycle is in progress, the RDSR command will output the full content of the status register. For easy detection of the internal write cycle completion, both during writing to the memory array and to the status register, we recommend sampling the RDY bit only through the polling routine. After detecting the RDY bit “0”, the next RDSR instruction will always output the expected content of the status register. CS 0 1 2 3 4 5 6 7 8 20 21 10 9 22 23 24 25 26 27 28 29 30 SCK OPCODE SI 0 0 0 0 0 0 BYTE ADDRESS* 1 1 A0 AN DATA OUT HIGH IMPEDANCE SO 7 Dashed Line = mode (1, 1) * Please check the Byte Address Table (Table 11) 6 5 4 3 2 1 0 MSB Figure 9. READ Timing CS 0 1 2 3 4 5 6 7 1 0 1 8 9 10 6 5 11 12 13 14 2 1 SCK OPCODE SI SO 0 0 0 0 0 DATA OUT HIGH IMPEDANCE 7 MSB Dashed Line = mode (1, 1) Figure 10. RDSR Timing http://onsemi.com 9 4 3 0 CAV25080, CAV25160 Hold Operation below the POR trigger level. This bi−directional POR behavior protects the device against ‘brown−out’ failure following a temporary loss of power. The CAV25080/160 device powers up in a write disable state and in a low power standby mode. A WREN instruction must be issued prior to any writes to the device. After power up, the CS pin must be brought low to enter a ready state and receive an instruction. After a successful byte/page write or status register write, the device goes into a write disable mode. The CS input must be set high after the proper number of clock cycles to start the internal write cycle. Access to the memory array during an internal write cycle is ignored and programming is continued. Any invalid op−code will be ignored and the serial output pin (SO) will remain in the high impedance state. The HOLD input can be used to pause communication between host and CAV25080/160. To pause, HOLD must be taken low while SCK is low (Figure 11). During the hold condition the device must remain selected (CS low). During the pause, the data output pin (SO) is tri−stated (high impedance) and SI transitions are ignored. To resume communication, HOLD must be taken high while SCK is low. Design Considerations The CAV25080/160 devices incorporate Power−On Reset (POR) circuitry which protects the internal logic against powering up in the wrong state. The device will power up into Standby mode after VCC exceeds the POR trigger level and will power down into Reset mode when VCC drops CS tCD tCD SCK tHD tHD HOLD tHZ HIGH IMPEDANCE SO tLZ Dashed Line = mode (1, 1) Figure 11. HOLD Timing http://onsemi.com 10 CAV25080, CAV25160 PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O E1 E SYMBOL MIN A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 MAX 4.00 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 θ 0º 8º TOP VIEW D h A1 θ A c e b L SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 11 CAV25080, CAV25160 PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 A2 0.80 b 0.19 0.15 0.90 1.05 0.30 c 0.09 D 2.90 3.00 3.10 E 6.30 6.40 6.50 E1 4.30 4.40 4.50 e 0.20 0.65 BSC L 1.00 REF L1 0.50 θ 0º 0.60 0.75 8º e TOP VIEW D A2 c q1 A A1 L1 SIDE VIEW L END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. http://onsemi.com 12 CAV25080, CAV25160 ORDERING INFORMATION (Notes 8−10) Specific Device Marking Package Type Temperature Range CAV25080VE−GT3 25080D SOIC−8, JEDEC E = Extended (−40°C to +125°C) NiPdAu Tape & Reel, 3,000 Units / Reel CAV25080YE−GT3 S08D TSSOP−8 E = Extended (−40°C to +125°C) NiPdAu Tape & Reel, 3,000 Units / Reel CAV25160VE−GT3 25160D SOIC−8, JEDEC E = Extended (−40°C to +125°C) NiPdAu Tape & Reel, 3,000 Units / Reel CAV25160YE−GT3 S16D TSSOP−8 E = Extended (−40°C to +125°C) NiPdAu Tape & Reel, 3,000 Units / Reel Device Order Number Lead Finish Shipping (Note 11) 8. All packages are RoHS−compliant (Lead−free, Halogen−free). 9. The standard lead finish is NiPdAu. 10. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. 11. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 13 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAV25080/D